Scenic Roller 40320 - Projection screen DA-LITE - Free user manual and instructions

Brand	Da-Lite
Model	Scenic Roller 40320
Product Type	Manual Pull-Down Projection Screen
Screen Material	Matte White Vinyl (gain 1.0)
Screen Format	4:3 aspect ratio
Diagonal Size	96 inches (typical for model)
Viewable Area (W x H)	78.5 x 58.9 inches
Operation	Manual pull-down with roller
Mounting Options	Wall or ceiling mount
Overall Dimensions (W x H x D)	85 x 6 x 6 inches (with case)
Weight	Approximately 15 lbs
Screen Color	White
Viewing Angle	180 degrees
Key Features	Easy installation, smooth retraction, durable fabric
Cleaning Instructions	Dust with soft cloth; avoid harsh chemicals
Safety Warnings	Keep away from children; do not pull excessively
Spare Parts Availability	Contact Da-Lite for replacement springs and fabric
Repairability	User-replaceable screen material and springs
Compliance	UL listed, CE marked
General Information	Manufacturer: Da-Lite, USA. Warranty: 2 years.

Frequently Asked Questions - Scenic Roller 40320 DA-LITE

How do I install the Scenic Roller 40320 screen?

Mount the brackets to the wall or ceiling using the provided hardware, ensuring they are level. Then slide the screen case into the brackets and secure it. Refer to the manual for detailed step-by-step instructions.

What is the recommended viewing distance?

For a 96-inch diagonal screen, the optimal viewing distance is approximately 1.5 to 2.5 times the screen height, which is about 7 to 12 feet.

Can I clean the screen surface with water?

Yes, you can lightly dampen a soft cloth with water and gently wipe the screen. Avoid using any chemical cleaners or abrasive materials as they may damage the surface.

How do I retract the screen?

Gently pull down the screen to the desired height, then release it slowly for smooth retraction. Do not let it snap back as this may damage the spring mechanism.

What should I do if the screen does not stay down?

Check the locking mechanism at the bottom handle. It should engage when fully extended. If it fails, consult the manual or contact support for spring adjustment.

Is the screen flame retardant?

Yes, the matte white vinyl material meets NFPA 701 standards for flame retardancy. It is safe for use in public venues.

Can I use this screen with a laser projector?

Yes, the screen works with both standard and laser projectors. However, ensure the projector's brightness is appropriate to avoid hotspotting.

How do I adjust the screen tension?

The tension is pre-set at the factory. For adjustments, turn the tension knobs located at the ends of the roller case. Only adjust if fabric is loose.

What is the warranty coverage?

Da-Lite offers a 2-year limited warranty covering manufacturing defects. It does not cover misuse or normal wear. Register your product online.

Where can I get replacement parts?

Contact Da-Lite customer service or an authorized dealer for replacement springs, fabric, or mounting brackets. Use only genuine parts.

USER MANUAL Scenic Roller 40320 DA-LITE

Empty whiteboard frame with black border and corner markers (no text or symbols)

Pre-Installation Installation

Having decided on hooks, chains, cables or other mounting method, have mounting prepared before opening box. Do not mount screen against walls that might rub fabric.

1. Remove screen from box by lifting roller at the ends. Be careful not to permit Id or any tools to fall on screen. During installation handle unit only by ends of roller and top header. Do not grasp around fabric, do not rest unit on fabric.
2. Remove wrapping paper and unwind ropes.
3. With the screen lying on the floor, install the clamps on the reinforcement tape on the header as shown in Figure 2. Clamp assembly is shown in Figure 1. Drop the closed loop of the turnbuckle in the slot of the clamp before inserting bolt. Each clamp uses three bolts and nuts. Do not tighten nuts any more than finger light. Make sure the ends of clamps do not push into the fabric. Pulleys at each end of header must be in the vertical position, when hung for proper operation.
4. Adjust top header in fabric pocket to the 2-1/4" and 3-3/4" position shown on the drawing.
5. Hang the screen in place at three, five, or seven points.

CAUTION! When this screen is shipped from the factory, there are 2-1/2 turns of rope around each end of the roller. Make certain that this is left unchanged to insure good operation.

CAUTION! Before dropping fabric make certain ropes at end of bottom roller do not overlap. Overlapping of ropes will cause rope to work inward and thus damage the fabric.

Screen Adjustment

1. Lower screen slowly by gradually releasing ropes.
2. With screen in the 'Down' position, turn the header in the fabric pocket carefully to adjust the pulleys to a vertical end position. Check the 2-1/4" and 3-3/4" end tube dimensions. Adjust the clamps on the reinforcement, tape. Clamps are not to push into fabric pocket. Tighten nuts on all bolts.
3. Total screen drop may be controlled by adjusting rope clamp. Do not adjust for more drop.
4. With unit in completely unrolled position, examine the screen carefully. If slight sag appears in center of fabric, adjust turnbuckles at the eye bolts until fabric hangs flat.

5. Screen may be raised by pulling on ropes. Tie off ropes to keep screen in raised position.

6. Protect your screen against damage and it will give many years of enjoyment.

a. When lowering screen, do so gently. Never allow it to drop uncontrolled.
b. Before raising screen, be sure both front and back sides are free from insects or any foreign matter.
c. Form the habit of looking in space between fabric and roller for foreign matter before raising screen.
d. Caution stage hands and others to avoid bumping screen with ladders, scenery, etc.

LIMITED ONE YEAR WARRANTY ON DA-LITE PRESENTATION PRODUCTS

Milestone AV Technologies LLC warrants certain Da-Lite branded products to the original purchaser only, to be free from defects in materials and workmanship for a period of one (1) year from the date of purchase by the original purchaser, provided they are properly operated according to Da-Lite's instructions and are not damaged due to improper handling or treatment after shipment from the factory.

This warranty does not apply to equipment showing evidence of misuse, abuse or accidental damage, or which has been tampered with or repaired by a person other than authorized Da Lite personnel.

Da-Lite's sole obligation under this warranty shall be to repair or to replace (at Da-Lite's option) the defective part of the merchandise. Returns for service should be made to your Da-Lite dealer. If it is necessary for the dealer to return the screen or part to Da-Lite, transportation expenses to and from Da-Lite are payable by the purchaser and De-Lite is not responsible for damage in shipment. To protect yourself against damage or loss in transit, insure the product and prepay all transportation expenses.

TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, THIS WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING WARRANTIES AS TO FITNESS FOR USE AND MERCHANTABILITY. Any implied warranties of fitness for use or merchantability, that may be mandated by statute or rule of law are limited to the one (1) year warranty period. This warranty gives you specific legal rights, and you may also have other rights, which vary from state to state. TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, NO LIABILITY IS ASSUMED FOR EXPENSES OR DAMAGES RESULTING FROM INTERRUPTION IN OPERATION OF EQUIPMENT, OR FOR INCIDENTAL, DIRECT, OR CONSEQUENTIAL DAMAGES OF ANY NATURE.

In the event that there is a defect in materials or workmanship of a Da-Lite product, you may contact our Sales Partners at PO Box 137, Warsaw, IN 46581-0137, [phone], [phone].

IMPORTANT: THIS WARRANTY SHALL NOT BE VALID AND DA-LITE BRANDED PRODUCTS SHALL NOT BE BOUND BY THIS WARRANTY IF THE PRODUCT IS NOT OPERATED IN ACCORDANCE WITH THE DA-LITE WRITTEN INSTRUCTIONS.

Keep your sales receipt to prove the date of purchase and your original ownership.