TA200 - Flat screen mount Chief - Free user manual and instructions

USER MANUAL TA200 Chief

INSTALLATION INSTRUCTIONS

Video Conferencing and Component Shelves

DISCLAIMER

Milestone AV Technologies and its affiliated corporations and subsidiaries (collectively "Milestone"), intend to make this manual accurate and complete. However, Milestone makes no claim that the information contained herein covers all details, conditions or variations, nor does it provide for every possible contingency in connection with the installation or use of this product. The information contained in this document is subject to change without notice or obligation of any kind. Milestone makes no representation of warranty, expressed or implied, regarding the information contained herein. Milestone assumes no responsibility for accuracy, completeness or sufficiency of the information contained in this document.

Chief® is a registered trademark of Milestone AV Technologies. All rights reserved.

IMPORTANT SAFETY INSTRUCTIONS!

WARNING: A WARNING alerts you to the possibility of serious injury or death if you do not follow the instructions.

CAUTION: A CAUTION alerts you to the possibility of damage or destruction of equipment if you do not follow the corresponding instructions.

WARNING: Failure to read, thoroughly understand, and follow all instructions can result in serious personal injury, damage to equipment, or voiding of factory warranty! It is the installer's responsibility to make sure all components are properly assembled and installed using the instructions provided.

WARNING: Failure to provide adequate structural strength for this component can result in serious personal injury or damage to equipment! It is the installer's responsibility to make sure the structure to which this component is attached can support five times the combined weight of all equipment. Reinforce the structure as required before installing the component.

WARNING: Exceeding the weight capacity can result in serious personal injury or damage to equipment! It is the installer's responsibility to make sure the combined weight of all equipment and accessories mounted on each TA100/200/250 shelf does not exceed 10 lbs (4.54 kg) per shelf.

WARNING: RISK OF INJURY TO PERSONS! Do not use this mounting system to support video equipment such as televisions or computer monitors.

WARNING: Do not use this product outdoors.

--SAVE THESE INSTRUCTIONS--

DIMENSIONS

TA100
SHELF CAN BE USED EITHER ABOVE OR BELOW SCREEN

[457.2] 18.00 [149.7] 5.90 [31.8] 1.25 [304.8] 12.00 [264.2] 11.19

Simple line drawing of a vertical cylindrical object mounted on a flat base (no text or symbols)

[560.3] 22.06 DISTANCE TO C/L OF TSSXXX SERIES SWING ARMS [552.3] 21.75 DISTANCE TO C/L OF TSSXXX SERIES SWING ARMS

LOWEST POSITION

[438] 17.25 DISTANCE TO C/L OF TS3XXXX SERIES SWING ARMS [446] 17.56 DISTANCE TO C/L OF TS5XXXX SERIES SWING ARMS

HIGHEST POSITION WITH EXTENDER BRACKET

[114.3] 4.50 HEIGHT ADJUSTMENT [388.8] 16.31 DISTANCE TO C/L OF TS3XXX SERIES SWING ARMS [380.9] 16.00 DISTANCE TO C/L OF TS3XXX SERIES SWING ARMS

HIGHEST POSITION WITHOUT EXTENDER BRACKET

DIMENSIONS (CONTINUED)
TA200
SHELF CAN BE USED EITHER ABOVE OR BELOW THE SCREEN

[31.8] 1.25 [6.4] .25 [7.1] .28 [101.6] 4.00 [101.6] 8.00 [03.2] 4.00 [184.2] 7.25

[555] 21.85 DISTANCE TO C/L OF THE TS3XXX SERIES SWING ARMS [562.9] 22.16 DISTANCE TO C/L OF TS5XXX SERIES SWING ARMS

HIGHEST EXTENSION

[SSS] 21.85 DISTANCE TO C/L OF THE TSXXXX SERIES SWING ARMS [562.9] 22.16 DISTANCE TO C/L OF TSXXXX SERIES SWING ARMS

LOWEST EXTENSION WITH EXTENDER BRACKET

[114.3] 4.50 HEIGHT ADJUSTMENT [383.5] 15.10 DISTANCE TO C/L OF THE 153XXX SERIES SWING ARMS [391.5] 15.41 DISTANCE TO C/L OF TS5XXX SERIES SWING ARMS

HIGHEST EXTENSION WITHOUT EXTENDER BRACKET

TA250
SHELF CAN BE USED EITHER ABOVE OR BELOW THE SCREEN

[31.8] 1.25 [6.4] .25 [101.6] 4.00 [7.1] .28 [152.4] 6.00 [304.8] 12.00 [48°] 1.90 [92.6] 3.65 [184.2] 7.25

Technical line drawing of a mechanical support bracket with mounting feet (no text or symbols)

[555] 21.85 DISTANCE TO C/L OF TS3XXX SERIES SWING ARMS [562.9] 22.16 DISTANCE TO C/L OF TS3XXX SERIES SWING ARMS

HIGHEST EXTENSION

[440.7] 17.35 DISTANCE TO C/L OF TSGXXX SERIES SWING ARMS [448.6] 17.66 DISTANCE TO C/L OF TSGXXX SERIES SWING ARMS

LOWEST EXTENSION WITH EXTENDER BRACKET

[114.3] 4.50 HEIGHT ADJUSTMENT [383.5] 15.10 DISTANCE TO C/L OF TS3XXX SERIES SWING ARMS [391.5] 15.41 DISTANCE TO C/L OF TS3XXX SERIES SWING ARMS

HIGHEST EXTENSION WITHOUT EXTENDER BRACKET

LEGEND

	Tighten Fastener
	Apretar elemento de fijación
	Befestigungsteil festziehen
	Apertar fixador
	Serrare il fissaggio
	Bevestiging vastdraaien
	Serrez les fixations
	Loosen Fastener
	Aflojar elemento de fijación
	Befestigungsteil lösen
	Desapertar fixador
	Allentare il fissaggio
	Bevestiging losdraaien
	Desserrez les fixations
	Phillips Screwdriver
	Destornillador Phillips
	Kreuzschlitzschraubendreher
	Chave de fendas Phillips
	Cacciavite a stella
	Kruiskopschroevendraaier
	Tournevis à pointe cruciforme
	Open-Ended Wrench
	Llave de boca
	Gabelschlüssel
	Chave de bocas
	Chiave a punte aperte
	Steeksleutel
	Clé à fourche
	By Hand
	A mano
	Von Hand
	Com a mão
	A mano
	Met de hand
	À la main
	Hex-Head Wrench
	Llave de cabeza hexagonal
	Sechskantschlüssel
	Chave de cabeça sextavada
	Chiave esagonale
	Zeskantsleutel
	Clé à tête hexagonale

Pencil Mark

Marcar con lápiz

Stiftmarkierung

Marcar com lápis

Segno a matita

Potloodmerkteken

Marquage au crayon

Drill Hole

Perforar

Bohrloch

Fazer furo

Praticare un foro

Gat boren

Percez un trou

Adjust

Ajustar

Einstellen

Ajustar

Regolare

Afstellen

Ajuster

Remove

Quitar

Entfernen

Remover

Rimuovere

Verwijderen

Retirez

Optional

Opcional

Optional

Opcional

Opzionale

Optie

En option

Security Wrench

Llave de seguridad

Sicherheitsschlüssel

Chave de segurança

Chiave di sicurezza

Veiligheidssleutel

Clé de sécurité

TOOLS REQUIRED FOR INSTALLATION

5/32" (included) 1/8" (included) #2 3/8"

PARTS

A (1) [attachment bracket] B (1) [extension bracket] C (1) [TA200 8" video conferencing shelf] [TA100 component shelf] [TA250 12" video conferencing shelf] D (1) [backing bracket] E (4) #10-24 x 3/8" F (6) 1/4-20 x 5/8" G (6) 1/4" M (8) 1" adhesive hook and loop H (4) #10-24 x 1/2" J (4) #10-24 K (1) 5/32" L (1) 1/8" N (1)* 1/4-20 x 3/8" *only with TA200 and TA250

Installation

Shelf Assembly

1. Use three 1/4-20 x 5/8" button head cap screws (F) and three 1/4" washers (G) to connect shelf (C) to either extension bracket (B) or attachment bracket (A). (See Figure 1)

NOTE: Use extension bracket (B) for larger displays or if component needs to be mounted further from the display.

(TA200 shown) With extension bracket ① (F) x 3 (G) x 3 (B) (C) Without extension bracket ① (F) x 3 (G) x 3 (A) (C)

Figure 1

1. If using extension bracket, use three 1/4-20 x 5/8" button head cap screws (F) and three 1/4" washers (G) to attach extension bracket (B) to attachment bracket (A). (See Figure 2)

(TA200 shown) (A) (D) (B) (G) x 3 (F) x 3 ②

Figure 2

Installation to Faceplate

TS525 or iCF50 Installation

NOTE: Display does NOT have to be removed for shelf installation.

1. Use four #10-24 x 3/8" button head cap screws (E) to connect attachment bracket (A) to swing arm faceplate. (See Figure 3) and (See Figure 4)

(upper installation) (display not shown for clarity) ① (E) x 4 (A)

Figure 3

(lower installation) (display not shown for clarity)

Figure 4

TS3XX or iCF30 Installation

1. If already installed, remove display from faceplate. See swing arm installation instructions for details.
2. Use four #10-24 x 1/2" Phillips head cap screws (H) and four #10-24 lock nuts (J) to connect attachment bracket (A) to faceplate. (See Figure 5) and (See Figure 6)

(J) x 4 (upper installation) (display not shown (A) for clarity) ② (H) x 4

Figure 5

(J) x 4 (A) (lower installation) (display not shown for clarity) ② (H) x 4

Figure 6

1. Reinstall display to faceplate. See swing arm installation instructions for details.

NOTE: If also installing side speaker brackets (TA300), attachment bracket (A) should also be attached to TA300 horizontal brackets for additional support. Use hardware provided with TA300. (See Figure 7)

Technical line drawing of a mechanical assembly with labeled component (A), showing structural components and mounting brackets (no text or symbols beyond label)

Figure 7

Camera/Component Installation

WARNING: Exceeding the weight capacity can result in serious personal injury or damage to equipment! It is the installer's responsibility to make sure the combined weight of all equipment and accessories mounted on the TA100/200/250 shelves does not exceed 10 lbs (4.54 kg) per shelf.

NOTE: Mounting options will vary depending on the type of camera being mounted.

NOTE: Camera or component can also be secured to mount by threading cable ties or a PAC103 safety strap (not included) through outside slots on shelf and around the device.

Using Adhesive Squares

1. Use up to eight adhesive hook and loop squares (M) to secure camera or component to shelf. Attach adhesive squares to bottom of camera first and then attach corresponding squares to shelf when the exact mounting location has been determined.

Using Screw (TA200/250 only)

1. Install 1/4-20 x 3/8" Phillips pan machine screw (N) through mounting slot and into hole on bottom of camera. (See Figure 8)

(TA250 shown) camera (example) mounting slot ② (N)

Figure 8

NOTE: It is also acceptable to mount the camera directly to the shelf without any screws or ties.

Adjustments

Height Adjustment

1. Loosen three 1/4-20 x 5/8" button head cap screws (F) holding extension bracket (B) or shelf (C) to attachment bracket (A). (See Figure 9)
2. Adjust height of shelf (C) as desired.
3. Tighten three 1/4-20 x 5/8" button head cap screws (F) holding extension bracket (B) or shelf (C) to attachment bracket (A). (See Figure 9)

with extension bracket without extension bracket ① ③ ② ②

Figure 9