WLR-2100 - Router SITECOM - Free user manual and instructions

USER MANUAL WLR-2100 SITECOM

Front view of a white Siemens 5G network switch with four Ethernet ports and a blue port, no visible text or symbols on the device body.

User Manual

TABLE OF CONTENTS

1 KEY FEATURES....4
2 PACKAGE CONTENTS....5
1 CAUTIONS....6
3 PRODUCT LAYOUT....7
4 NETWORK + SYSTEM REQUIREMENTS ....10
5 WLR-2100/3100 PLACEMENT....10
6 SETUP LAN, WAN....11
7 PC NETWORK ADAPTER SETUP ....12
8 BRING UP THE WLR-2100/3100....16
9 INITIAL SETUP WLR-2100/3100 ....16
10 CONFIGURATION WIZARD....25
11 WIRELESS SETTINGS ....27
12 FIREWALL SETTINGS ....37
13 ADVANCED SETTINGS....43
14 TOOLBOX SETTINGS....50

Revision 1.0

© Sitecom Europe BV 2012

Note: All the information contained in this manual was correct at the time of publication.

However, as our engineers are always updating and improving the product, your device's software may have a slightly different appearance or modified functionality than presented in this manual.

Introduction

Congratulations on your purchase of the WLR-2100/3100 Wireless Network Broadband Router. The WLR-2100/3100 is compliant with 802.11n and up to 6 times faster than standard 802.11g based routers while still being compatible with 802.11g & 802.11b. The WLR-2100/3100 is not only a Wireless Access Point, but also doubles as a 4-port full-duplex Switch that connects your wired-Ethernet devices together.

At 300 Mbps wireless transmission rate, the Access Point built into the Router uses advanced MIMO (Multi-Input, Multi-Output) technology to transmit multiple streams of data in a single wireless channel, giving you seamless access to multimedia content. Robust RF signal travels farther, eliminates dead spots and extends network range. For data protection and privacy, the WLR-2100/3100 encodes all wireless transmissions with WEP, WPA, and WPA2 encryption.

With the inbuilt DHCP Server & powerful SPI firewall, the WLR-2100/3100 protects your computers against intruders and most known Internet attacks but provides safe VPN pass-through. With incredible speed and QoS function of 802.11n(draft2.0), the WLR-2100/3100 is ideal for media-centric applications like streaming video, gaming, and VoIP telephony to run multiple media-intense data streams through the network at the same time, with no degradation in performance.

The router includes Sitecom Cloud Security to protect your home network against cybercrime.

1 Key Features

Features	Advantages
Incredible Data Rate up to 300Mbps	Heavy data payloads such as MPEG video streaming
IEEE 802.11n compliant and backwards compatible with 802.11b/g	Fully Interoperable with IEEE 802.11b / IEEE802.11g compliant devices with legacy protection
Four 10/100 Mbps Fast Switch Ports (Auto-Crossover)	Scalability, extend your network .
Firewall supports Virtual Server Mapping, DMZ, IP Filter, ICMP Blocking, SPI	Avoids the attacks of Hackers or Viruses from Internet
Support 802.1x authenticator, 802.11i (WPA/WPA2, AES), VPN pass-through	Provide mutual authentication (Client and dynamic encryption keys to enhance security
Sitecom Cloud Security	Security integrated in the router protects all the devices in your network against cybercrime when surfing the Internet.

* Theoretical wireless signal rate based on IEEE standard of 802.11a, b, g, n chipset used. Actual throughput may vary. Network conditions and environmental factors lower actual throughput rate. All specifications are subject to change without notice.

2 Package Contents

Open the package carefully, and make sure that none of the items listed below are missing. Do not discard the packing materials, in case of return; the unit must be shipped back in its original package.

1. WLR-2100/3100 Router
2. 5V 1A Power Adapter
3. Quick Install Guide
4. CD (User's Manual)
5. Warranty card
6. UTP cable

3 Cautions

This router's design and manufacturer has your safety in mind. In order to safely and effectively use this router, please read the following before usage.

3.1 Usage Cautions

The user should not modify this router. The environmental temperature should be within +5 \~ +35 degrees Celsius.

3.2 Power

The router's power voltage is DC 5V 1A.

When using this router, please connect the supplied AC adapter or AC adapter cable to the router's power jack. When placing the adapter cable, make sure it can not get damaged or be subject to pressure. To reduce the risk of electric shock, unplug the adapter first before cleaning it. Never connect the adapter to the router in a humid or dusty area. Do not replace the adapter or cable's wire or connector.

3.3 Repair

If the router has a problem, you should take it to an appointed repair centre and let the specialists do the repair. Never repair the router yourself, you might damage the router or endanger yourself.

3.4 Disposing of the Router

When you dispose of the router, be sure to dispose it appropriately. Some countries may regulate disposal of an electrical device, please consult with your local authority.

3.5 Others

When using this router, please do not let it come into contact with water or other liquids. If water is accidentally spilled on the router, please use a dry cloth to absorb the spillage. Electronic products are vulnerable, when using please avoid shaking or hitting the router, and do not press the buttons too hard.

• Do not let the router come into contact with water or other liquid.
• Do not disassemble the router; repair the router or change the design of the router, any damage done will not be included in the repair policy.
• Avoid hitting the router with a hard object, avoid shaking the router and stay away from magnetic fields.
• If during electrostatic discharge or a strong electromagnetic field the product will malfunction, unplug the power cable. The product will return to normal performance the next time it is powered on.

4 Product Layout

Front view of a white GE Telecom network switch with four Ethernet ports and a blue port (no visible text or symbols)

Port	Description
Power connector	Connect the 5V DC adapter to this port
LAN (Yellow)	Connect your PC's or network devices to this port
WAN (Blue)	Connect your ADSL/Cable modem to this port

Backlabel

The backlabel describes the IP address, login details, SSID, security code and WPS button functionality.

To access the router configuration, type the following IP address in your internet browser: 192.168.0.1 Username: admin Password: To make a wireless connection with this router, choose the network: WPA2 code: Serial No.: Wireless Router 300N X2 SITECOM Model No: WLR-2000 v2 001 CE! 8"716502"023585" Made in Taiwan Designed in Europe Press 2 sec. = OPS mode Press 10 sec. = Reset Press 15 sec. = Factory default MODEM LAN LAN LAN

Button	Description
WPS BUTTON	Press 2 seconds for WPS modePress 10 seconds to reset the routerPress 15 Seconds to reset the router to factory defaults.

LED Definition

From left to right.

Port	Description
LAN (Blue)	Shows the cable is connected.
LAN (Blue)	Shows the cable is connected.
LAN (Blue)	Shows the cable is connected.
LAN (Blue)	Shows the cable is connected.
WAN (Blue)	Shows the cable is connected.
WiFi (Blue)	Shows WiFi activity and WPS.
Power (Red)	Shows the device is turned on.

Front view of a white SITCOM networking device with four Ethernet ports and a blue port, no visible text or symbols on the device body.

5 Network + System Requirements

To begin using the WLR-2100/3100, make sure you meet the following as minimum requirements:

• PC/Notebook.
• Operating System – Microsoft Windows XP/VISTA/7
  • 1 Free Ethernet port.
• WiFi card/USB dongle (802.11 b/g/n) – optional.
• External xDSL (ADSL) or Cable modem with an Ethernet port (RJ-45).
  • PC with a Web-Browser (Internet Explorer, Safari, Firefox, Opera)
• Ethernet compatible CAT5 cables.

6 WLR-2100/3100 Placement

You can place the WLR-2100/3100 on a desk or other flat surface, or you can mount it on a wall. For optimal performance, place your Wireless Broadband Router in the center of your office (or your home) in a location that is away from any potential source of interference, such as a metal wall or microwave oven. This location must be close to a power connection and your ADSL/Cable modem.

7 Setup LAN, WAN

WAN connection:

Line SITSCOM MODEM

LAN connection:

LAN PC

8 PC Network Adapter setup

Windows XP

- Enter [Start Menu] select [Control panel] select [Network].

Network Connections File Edit View Favorites Tools Advanced Help Back Search Polders Address Network Connections Network Tasks Create a new connection Set up a phone or small office network Change Windows Firewall settings See Also Network Troubleshooter Other Places Control Panel My Network Places Internet Gateway Internet Connection Connected Internet Connection LAN or High-Speed Internet Wireless Network Connection Not connected, Promoted Internet LAN/Wireless LAN/CAA Local Area Connection Connected, Promoted Internet LAN/CAA/2013 PCE E... L394 Connection Connected, Connected L394 Net Adapter

- Select [Local Area Connection]) icon =>select [properties]

Local Area Connection Connected, Firewalled Realtek Disable Status Repair Bridge Connections Create Shortcut Delete Rename Properties

- Select [Internet Protocol (TCP/IP)] =>Click [Properties].

Local Area Connection Properties General | Authentication | Advanced | Connect using: Realtek RTL8168/8111 PCI-E Gigabi Configure... This connection uses the following items: Network Monitor Driver Microsoft TCP/IP version 6 Internet Protocol (TCP/IP) Install... Uninstall Properties Description Transmission Control Protocol/Internet Protocol. The default wide area network protocol that provides communication across diverse interconnected networks. Show icon in notification area when connected Notify me when this connection has limited or no connectivity OK Cancel

Internet Protocol (TCP/IP) Properties General Alternate Configuration You can get IP settings assigned automatically if your network supports this capability. Otherwise, you need to ask your network administrator for the appropriate IP settings. Obtain an IP address automatically a Use the following IP address: IP address: Subnet mask: Default gateway: Obtain DNS server address automatically a Use the following DNS server addresses: Preferred DNS server: Alternate DNS server: Advanced... OK Cancel

- Select the [General] tab.

The router supports [DHCP] function, please select both [Obtain an IP address automatically] and [Obtain DNS server address automatically].

Windows Vista/Seven

- Enter [Start Menu] → select [Control panel] → select [View network status and tasks] -> select [Manage network connections].

Network and Internet ▶ Network Connections ▶ Organize ▶ Views ▶ Name Status Device Name Connectivity Network Category Owner LAN or High-Speed Internet (2) Local Area Connection Network_2 Broadcom 440x10/100 Integ... Wireless Network Connection Not connected Broadcom 602.11g Network ...

- Select [Local Area Connection]) icon =>select [properties]

Network and Internet > Network Connections Organize > Views > Disable this network device Name Status Device Name Connectivity Network LAN or High-Speed Internet (2) Local Area Connection Network 2 Broadcom 440x10 Wireless Network Co Disable Status Diagnose Bridge Connections Create Shortcut Delete Rename Properties

- Select [Internet Protocol Version 4 (TCP/IPv4)] =>Click [Properties].

Local Area Connection Properties Networking Sharing Connect using: Broadcom 440x 10/100 Integrated Controller Configure... This cgnction uses the following items: ✓ Client for Microsoft Networks ✓ QoS Packet Scheduler ✓ File and Printer Sharing for Microsoft Networks ✓ Internet Protocol Version 6 (TCP/IPv6) ✓ Internet Protocol Version 4 (TCP/IPv4) ✓ Link-Layer Topology Discovery Mapper I/O Driver ✓ Link-Layer Topology Discovery Responder Install... Uninstall Properties Description Transmission Control Protocol/Internet Protocol. The default wide area network protocol that provides communication across diverse interconnected networks. OK Cancel

Internet Protocol Version 4 (TCP/IPv4) Properties General Alternate Configuration You can get IP settings assigned automatically if your network supports this capability. Otherwise, you need to ask your network administrator for the appropriate IP settings. Obtain an IP address automatically Use the following IP address: IP address: . Subnet mask: . Default gateway: . Obtain DNS server address automatically Use the following DNS server addresses: Preferred DNS server: . Alternate DNS server: . Advanced... OK Cancel

- Select the [General] tab.

The router supports [DHCP] function, please select both [Obtain an IP address automatically] and [Obtain DNS server address automatically].

9 Bring up the WLR-2100/3100

Connect the supplied power-adapter to the power inlet port and connect it to a wall outlet. The WLR-2100/3100 automatically enters the self-test phase. During self-test phase, the Power LED will be lit continuously to indicate that this product is in normal operation.

10 Initial Setup WLR-2100/3100

LOGIN procedure

1. OPEN your browser (e.g. Internet Explorer).

1. Type http://192.168.0.1 in the address bar and press [Enter]

Blank Page - Windows Internet Explorer http://192.168.0.1/ File Edit View Favorites Tools Help Connecting... Connect to 192.168.0.1 The server 192.168.0.1 requires a username and password. Warning: This server is requesting that your username and password be sent in an insecure manner (basic authentication without a secure connection). User name: Password: Remember my password OK Cancel

1. Type user name and password (default username is admin. The password can be found on the backlabel on the bottom of your router).

Connect to 192.168.0.1 The server 192.168.0.1 requires a username and password. Warning: This server is requesting that your username and password be sent in an insecure manner (basic authentication without a secure connection). User name: admin Password: ****** Remember my password OK Cancel

1. Click OK.

2. You will see the home page of the WLR-2100/3100.

Status Wizard Wireless Settings Firewall Advanced Settings Toolbox Choose your language System Status DHCP Server Device States Internet States DHCP Status Log Statistics IPv6 You can use the Status page to monitor the connection status for the WAN/LAN interfaces, firmware and hardware version numbers, any illegal attempts to access your network and information on all DHCP client PCs currently connected to your network. System Model : WLR-1000 Up Time : 0day:Oh:8mu:8s Hardware Version : Rev. A Boot Code Version : 1.0 Runtime Code Version : 1.07

The System status section allows you to monitor the current status of your router.

The UP time, hardware information, serial number as well as firmware version information is displayed here.

DHCP Server

The LAN tab gives you the opportunity to change the IP settings of the WLR-2100/3100.

Status Wizard Wireless Settings Firewall Advanced Settings Toolbox Choose your language System Status DHCP Server Device Status Internet Status DHCP Status Log Statistics TP6 You can enable the Wireless Router's DHCP server to dynamically allocate IP Addresses to your LAN client PCs. The Wireless Router must have an IP Address in the Local Area Network. LAN IP IP Address : 192.168.0.1 Subnet Mask : 255.255.255.0 802.1d Spanning Tree : Disable DHCP Server : Enable Lense Time : Forever DHCP Server DHCP Client Start IP : 192.168.0.100 DHCP Client End IP : 192.168.0.200 Domain Name : sitocomw/r1000 Apply Cancel

Click at the bottom of this screen to save any changes.

IP address 192.168.0.1. It is the router's LAN IP address (Your LAN clients default gateway IP address).

IP Subnet Mask 255.255.255.0 Specify a Subnet Mask for your LAN segment.

802.1d Spanning Tree is Disabled by default. If the 802.1d Spanning Tree function is enabled, this router will use the spanning tree protocol to prevent network loops.

DHCP Server Enabled by default. You can enable or disable the DHCP server. When DHCP is disabled no ip-addresses are assigned to clients and you have to use static ip-addresses. When DHCP server is enabled your computers will be assigned an ip-address automatically until the lease time expires.

Lease Time Forever. In the Lease Time setting you can specify the time period that the DHCP lends an IP address to your LAN clients. The DHCP will change your LAN client's IP address when this time threshold period is reached.

DHCP START client IP/DHCP Client end IP You can select a particular IP address range for your DHCP server to issue IP addresses to your LAN Clients.

Note: default IP range 192.168.0.100 192.168.0.200. If you want your PC(s) to have a static/fixed IP address, then you'll have to choose an IP address outside this IP address Pool

Domain Name You can specify a Domain Name for your LAN. Or just keep the default (sitecomwlrxxxx).

Device Status

View the Broadband router's current configuration settings. Device Status displays the configuration settings you've configured in the Wizard / Basic Settings / Wireless Settings section.

Status Wizard Wireless Settings Firewall Advanced Settings Toolbox Choose your language System Status DHCP Server Device Status Internet Status DHCP Status Log Statistics TIPG View the current setting status of this device. Wireless Configuration Mode: Access Point ESSID: SibecomC7A7B0 Channel Number: auto Security: WPA pre-shared key LAN Configuration IP Address: 192.168.0.1 Subnet Mask: 255.255.255.0 DHCP Server: Enable MAC Address: 00:0C:F6:00:00:00

Internet Status

This page displays whether the WAN port is connected to a Cable/DSL connection. It also displays the router's WAN IP address, Subnet Mask, and ISP Gateway as well as MAC address, the Primary DNS. Press Renew button to renew your WAN IP address.

Status Wizard Wireless Settings Firewall Advanced Settings Toolbox Choose your language System Status DHCP Server Device Status Internet Status DHCP Status Log Statistics IPv6 View the current internet connection status and related information. Attain IP Protocol : Dynamic IP disconnect IP Address : Subnet Mask : Default Gateway : MAC Address : 00:0C:F5:6A:D2:91 Primary DNS : Secondary DNS : Refresh

DHCP Client Status

DHCP This page shows all DHCP clients (LAN PCs) currently connected to your network. The table shows the assigned IP address, MAC address and expiration time for each DHCP leased client. Use the Refresh button to update the available information.

You can check Enable Static DHCP IP. It is possible to add more static DHCP IPs.

They are listed in the table Static DHCP Lease Table. IP can be deleted at will from the table.

Click the 'apply' button to save the changed configuration.

Status Wizard Wireless Settings Firewall Advanced Settings Toolbox Choose your language System Status DHCP Server Device Status Internet Status DHCP Status Lug Statistics IPv6 This table shows the assigned IP address, MAC address and time expired for each DHCP leased client. IP Address MAC Address Time Expired (Second) 192.168.0.100 00:26:22/ac:5f:2a forever Refresh Enable Static DHCP Leases IP Address MAC Address Add Clear Static DHCP Lease Table : NO. MAC Address IP Address Select Delete Delete All Apply Cancel

WLR-2100/3100 Log

View the operation log of the WLR-2100/3100. This page shows the current system log of the Broadband router. It displays any event occurred after system start up. At the bottom of the page, the system log can be saved to a local file for further processing or the system log can be cleared or it can be refreshed to get the most updated information. When the system is powered down, the system log will disappear if not saved to a local file.

System Status DHCP Server Device Status Internet Status DHCP Status Log Statistics IPv6 View the system operation information. You can see the system start up time, connection process, etc. Jul 28 00:00:01 (none) syslog.info syslogd started: BusyBox v1.15.2 Save Clear Refresh

WLR-2100/3100 Statistics

Shows the counters of packets sent and received on WAN, LAN & WLAN.

Status Wizard Wireless Settings Firewall Advanced Settings Toolbox Choose your language System Status DHCP Server Device Status Internet Status DHCP Status Log Statistics IPv6 This page shows the packet counters for transmission and reception regarding to networks. Wireless LAN : Packets Sent 440 Packets Received 0 Ethernet LAN : Packets Sent 1639 Packets Received 2192 Ethernet WAN : Packets Sent 0 Packets Received 0 Refresh

11 Configuration Wizard

Click Wizard to configure the router. The Setup wizard will now be displayed; check that the modem is connected and click Next.

300N ROUTER WIRELESS SITECOM Status Wizard Wireless Settings Firewall Advanced Settings Toolbox Choose your language Setup Wizard The Setup Wizard will guide you step by step through a basic configuration procedure. Next

Select your country from the Country list. Select your internet provider. Click Next.

300N ROUTER WIRELESS SITECOM Status Wizard Wireless Settings Firewall Advanced Settings Toolbox Choose your language Select your country and ISP Country : Netherlands Service : Selectser uw provider Selectser uw provider ADSL Provider (alle modem types in u.v. Speedtouch Home modem) ADSL Provider met Speedtouch Home modem Kabel Provider (zonder gebruikensteem en wachword) Kabel Provider met gebruikvername en wachword Kabel Provider (wachword, Verduver type) Previous Next

Depending on the chosen provider, you may need to enter your user name and password, MAC address or hostname in the following window. After you have entered the correct information, click Next.

300N ROUTER WIRELESS SITECOM Status Wizard Wireless Settings Firewall Advanced Settings Toolbox Choose your language Please, enter the data which is supplied by your ISP. Hostname : (Aleen voor audere ©home verbindingen) MAC Address : 00000000000 Clone MAC address Previous Apply Cancel 300N ROUTER WIRELESS SITECOM Status Wizard Wireless Settings Firewall Advanced Settings Toolbox Choose your language Please, enter the data which is supplied by your ISP. Login Method : PPP over Ethernet Username : Password : Service : MTU : 1452 (312<=MTU Value<=1492) Connection Type : Keep connection Connect Disconnect Idle Time : 10 (1-1000 Minutes) Previous Apply Cancel

Click APPLY to complete the configuration.

12 Wireless Settings

You can set parameters that are used for the wireless stations to connect to this router. The parameters include Mode, ESSID, Channel Number and Associated Client.

Wireless Function

Status Wizard Wireless Settings Firewall Advanced Settings Toolbox Choose your language Enable Basic Advanced Security ACL WPS The gateway can be quickly configured as a wireless access point for roaming clients by setting the SSID and channel number. It also supports data encryption and client filtering. Wireless Module: Enable Disable Apply

Enable or Disable Wireless function here. Click Apply and wait for module to be ready and loaded.

Basic Settings

Status Wizard Wireless Settings Firewall Advanced Settings Toolbox Choose your language Enable Basic Advanced Security ACI WPS This page allows you to define the ESSID and Channel for the wireless connection. These parameters are used for the wireless stations to connect to the Access Point. Mode: Access Point Band: 2.4 GHz (B+G+N) SSID: SitecomC7A7B0 Channel: Auto Apply Cancel

Band Allows you to set the AP fixed at 802.11b or 802.11g mode. You can also select B+G mode to allow 80211b and 802.11g clients at the same time.

SSID This is the name of the wireless signal which is broadcasted. All the devices in the same wireless LAN should have the same SSID.

Channel The channel used by the wireless LAN. All devices in the same wireless LAN should use the same channel.

Advanced

This tab allows you to set the advanced wireless options. The options included are, Fragment Threshold, RTS Threshold, Beacon Interval, and Preamble Type. You should not change these parameters unless you know what effect the changes will have on the router.

Status Wizard Wireless Settings Firewall Advanced Settings Toolbox Choose your language Enable Basic Advanced Security ACL WPS These settings are only for more technically advanced users who have a sufficient knowledge about wireless LAN. These settings should not be changed unless you know what effect the changes will have on your Access Point. Fragment Threshold : 2346 (256-2346) RTS Threshold : 2347 (0-2347) Beacon Interval : 100 (20-1024 ms) DTIM Period : 1 (1-10) Data Rate : Auto N Data Rate : Auto Channel Bandwidth : Auto 20/40 MHZ 20 MHZ Preamble Type : Short Preamble Long Preamble CTS Protection : Always None Apply Cancel

Fragment Threshold "Fragment Threshold" specifies the maximum size of a packet during the fragmentation of data to be transmitted. If you set this value too low, it will result in bad performance.

RTS Threshold When the packet size is smaller then the RTS threshold, the wireless router will not use the RTS/CTS mechanism to send this packet.

Beacon Interval is the interval of time that this wireless router broadcasts a beacon. A Beacon is used to synchronize the wireless network.

Data Rate The "Data Rate" is the rate that this access point uses to transmit data packets. The access point will use the highest possible selected transmission rate to transmit the data packets.

N Data Rate The "Data Rate" is the rate that this access point uses to transmit data packets for N compliant wireless nodes. Highest to lowest data rate can be fixed.

Channel Bandwidth is the range of frequencies that will be used.

Preamble Type The "Long Preamble" can provide better wireless LAN compatibility while the "Short Preamble" can provide better wireless LAN performance.

CTS Protection: It is recommended to enable the protection mechanism. This mechanism can decrease the rate of data collision between 802.11b and 802.11g wireless stations. When the protection mode is enabled, the throughput of the AP will be a little lower due to a lot of frame-network that is transmitted.

Security

This Access Point provides complete wireless LAN security functions, included are WEP, IEEE 802.11x, IEEE 802.11x with WEP, WPA with pre-shared key and WPA with RADIUS. With these security functions, you can prevent your wireless LAN from illegal access. Please make sure your wireless stations use the same security function, and are setup with the same security key.

Disable

When you choose to disable encryption, it is very insecure to operate the WLR-2100/3100.

Enable Basic Advanced Security ACL WPS This page allows you setup the wireless security. Turn on WEP or WPA by using Encryption Keys could prevent any unauthorized access to your wireless network. Encryption : Disable Enable 802.1x Authentication Apply Cancel

WPA Radius

IEEE 802.1x is an authentication protocol. Every user must use a valid account to login to this Access Point before accessing the wireless LAN. The authentication is processed by a RADIUS server. This mode only authenticates users by IEEE 802.1x, but it does not encrypt the data during communication

Status Wizard Wireless Settings Firewall Advanced Settings Toolbox Choose your language enable Basic Advanced Security ACL WPS This page allows you to setup the wireless security. Turning on WEP or WPA by using Encryption Keys could prevent any unauthorized access to your wireless network. WMM: Enable Broadcast Essid: Enable Encryption: WPA RADIUS WPA Unicast Cipher Suite: ○ WPA(TKIP) ● WPA2(AE5) ○ WPA2 Mixed RADIUS Server IP Address: RADIUS Server Port: 1812 RADIUS Server Password: Apply Cancel

WEP

When you select 64-bit or 128-bit WEP key, you have to enter WEP keys to encrypt data. You can generate the key by yourself and enter it. You can enter four WEP keys and select one of them as a default key. Then the router can receive any packets encrypted by one of the four keys.

Encryption : WEP Key Length : 64-bit Key Type : ASCII (5 characters) Default Key : Key 1 Encryption Key 1 : Encryption Key 2 : Encryption Key 3 : Encryption Key 4 :

Key Length You can select the WEP key length for encryption, 64-bit or 128-bit. The larger the key will be the higher level of security is used, but the throughput will be lower.

Key Format You may select ASCII Characters (alphanumeric format) or Hexadecimal Digits (in the "A-F", "a-f" and "0-9" range) to be the WEP Key.

Key1 - Key4 The WEP keys are used to encrypt data transmitted in the wireless network. Use the following rules to setup a WEP key on the device. 64-bit WEP: input 10-digits Hex values (in the "A-F", "a-f" and "0-9" range) or 5-digit ASCII character as the encryption keys. 128-bit WEP: input 26-digit Hex values (in the "A-F", "a-f" and "0-9" range) or 13-digit ASCII characters as the encryption keys.

Click at the bottom of the screen to save the above configurations. You can now configure other sections by choosing Continue, or choose Apply to apply the settings and reboot the device.

WPA Pre-shared Key

Wi-Fi Protected Access (WPA) is an advanced security standard. You can use a pre-shared key to authenticate wireless stations and encrypt data during communication. It uses TKIP or CCMP (AES) to change the encryption key frequently. So the encryption key is not easy to be cracked by hackers. This is the best security available.

Encryption : WPA pre-shared key WPA Type : ○ WPA(TKIP) ○ WPA2(AES) ○ WPA2 Mixed Pre-shared Key Type : Passphrase Pre-sharedKey : Apply Cancel

WPA-Radius

Wi-Fi Protected Access (WPA) is an advanced security standard. You can use an external RADIUS server to authenticate wireless stations and provide the session key to encrypt data during communication. It uses TKIP or CCMP (AES) to change the encryption key frequently. Press Apply button when you are done.

Encryption : WPA RADIUS WPA Type : ○ WPA(TKIP) ○ WPA2(AES) ○ WPA2 Mixed RADIUS Server IP Address : RADIUS Server Port : 1812 RADIUS Server Password : Apply Cancel

ACL

This wireless router supports MAC Address Control, which prevents unauthorized clients from accessing your wireless network.

Status Wizard Wireless Settings Firewall Advanced Settings Toolbox Choose your language Enable Basic Advanced Security ACL WPS For security reasons, the Wireless Router features MAC Address Filtering that only allows authorized MAC Addresses to associate with the Wireless Router. MAC Address Filtering Table NO. MAC Address Comment Select Delete Delete All Enable Access Control New: MAC Address: Comment: Add Reset Apply Cancel

Enable wireless access control Enables the wireless access control function

Adding an address into the list Enter the "MAC Address" and "Comment" of the wireless station to be added and then click "Add". The wireless station will now be added into the "Current Access Control List" below. If you are having any difficulties filling in the fields, just click "Clear" and both "MAC Address" and "Comment" fields will be cleared.

Remove an address from the list If you want to remove a MAC address from the "Current Access Control List", select the MAC address that you want to remove in the list and then click "Delete Selected". If you want to remove all the MAC addresses from the list, just click the "Delete All" button. Click "Reset" will clear your current selections.

Click at the bottom of the screen to save the above configurations. You can now configure other sections by choosing Continue, or choose Apply to apply the settings and reboot the device.

WPS

Wi-Fi Protected Setup (WPS) is the simplest way to establish a connection between the wireless clients and the wireless router. You don't have to select the encryption mode and fill in a long encryption passphrase every time when you try to setup a wireless connection. You only need to press a button on both wireless client and wireless router, and WPS will do the rest for you.

The wireless router supports two types of WPS: WPS via Push Button and WPS via PIN code. If you want to use the Push Button, you have to push a specific button on the wireless client or in the utility of the wireless client to start the WPS mode, and switch the wireless router to WPS mode. You can simply push the WPS button of the wireless router, or click the 'Start to Process' button in the web configuration interface. If you want to use the PIN code, you have to know the PIN code of the wireless client and switch it to WPS mode, then fill-in the PIN code of the wireless client through the web configuration interface of the wireless router.

Status Wizard Wireless Settings Firewall Advanced Settings Toolbox Choose your language Enable Basic Advanced Security ACL WPS WPS : Enable WPS Information WPS Current Status : Configured PinCode Self : 04534082 SSID : SitecomC7A7B0 Authentication Mode : WPA pre-shared key PassphraseKey : *************** Current Password WPS Via Push Button : Start to Process WPS Via PIN : Start PIN

WPS Check the box to enable WPS function and uncheck it to disable the WPS function.

WPS Current Status If the wireless security (encryption) function of this wireless router is properly set, you'll see a 'Configured' message here. Otherwise, you'll see 'UnConfigured'.

Self Pin Code This is the WPS PIN code of the wireless router. You may need this information when connecting to other WPS-enabled wireless devices.

SSID This is the network broadcast name (SSID) of the router.

Authentication Mode It shows the active authentication mode for the wireless connection.

Passphrase Key It shows the passphrase key that is randomly generated by the wireless router during the WPS process. You may need this information when using a device which doesn't support WPS.

WPS via Push Button Press the button to start the WPS process. The router will wait for the WPS request from the wireless devices within 2 minutes.

WPS via PIN You can fill-in the PIN code of the wireless device and press the button to start the WPS process. The router will wait for the WPS request from the wireless device within 2 minutes.

13 Firewall Settings

The Broadband router provides extensive firewall protection by restricting connection parameters, thus limiting the risk of hacker attacks, and defending against a wide array of common Internet attacks. However, for applications that require unrestricted access to the Internet, you can configure a specific client/server as a Demilitarized Zone (DMZ).

Note: To enable the Firewall settings select Enable and click Apply

Status Wizard Wireless Settings Firewall Advanced Settings Toolbox Choose your language Enable DMZ DoS Access URL block The Wireless Router provides extensive firewall protection by restricting connection parameters, thus limiting the risk of hacker attack, and defending against a wide array of common attacks. However, for applications that require unrestricted access to the Internet, you can configure a specific client/server as a Demilitarized Zone (DMZ). Firewall Module: Enable Disable Apply

DMZ

If you have a client PC that cannot run an Internet application (e.g. Games) properly from behind the NAT firewall, then you can open up the firewall restrictions to unrestricted two-way Internet access by defining a DMZ Host. The DMZ function allows you to re-direct all packets going to your WAN port IP address to a particular IP address in your LAN. The difference between the virtual server and the DMZ function is that the virtual server re-directs a particular service/Internet application (e.g. FTP, websites) to a particular LAN client/server, whereas DMZ re-directs all packets (regardless of services) going to your WAN IP address to a particular LAN client/server.

Status Wizard Wireless Settings Firewall Advanced Settings Toolbox Choose your language Enable DMZ Des Access URL block If you have a local client PC that cannot run an Internet application properly from behind the NAT firewall, you can open the client up to unrestricted two-way Internet access by defining a Virtual DMZ Host. Enable DMZ Public IP Address Client PC IP Address Dynamic IP Session 1 Static IP Add Reset Current DMZ Table: NO. Public IP Address Client PC IP Address Select Delete Delete All Reset Apply Cancel

Enable DMZ Enable/disable DMZ

Public IP Address The IP address of the WAN port or any other Public IP addresses given to you by your ISP

Client PC IP Address Fill-in the IP address of a particular host in your LAN that will receive all the packets originally going to the WAN port/Public IP address above.

Click at the bottom of the screen to save the above configurations.

Denial of Service (DoS)

The Broadband router's firewall can block common hacker attacks, including Denial of Service, Ping of Death, Port Scan and Sync Flood. If Internet attacks occur the router can log the events.

Status Wizard Wireless Settings Firewall Advanced Settings Toolbox Choose your language Enable DMZ DoS Access URL block The Wireless Router's firewall can block common hacker attacks, including DoS, Discard Ping from WAN and Port Scan. Denial of Service features Ping of Death : ✓ Discard Ping on WAN : ✓ Port Scan : ✓ Sync Flood : ✓ Advanced Settings Apply Cancel

Ping of Death Protections from Ping of Death attack

Discard Ping From WAN The router's WAN port will not respond to any Ping requests

Port Scan Protects the router from Port Scans.

Sync Flood Protects the router from Sync Flood attack.

Access

You can restrict users from accessing certain Internet applications/services (e.g. Internet websites, email, FTP etc.), Access Control allows users to define the traffic type permitted in your LAN. You can control which PC client can have access to these services.

Status Wizard Wireless Settings Firewell Advanced Settings Toolbox Choose your language Enable DMZ DoS Access BRL block Access Control allows users to define the traffic type permitted or not permitted in your LAN. You can control which PC client uses what services in which they can have access to these services. If both MAC filtering and IP filtering are enabled simultaneously, the MAC filtering table will be checked first and then the IP filtering table. Enable MAC Filtering ▶ Deny ▶ Allow Client PC MAC Address Comment Add Reset Current MAC Filtering Table NO. Client PC MAC Address Comment Select Delete Delete All Reset Enable IP Filtering ▶ Deny ▶ Allow NO. PC Description PC IP Address Client Service Protocol Port Range Select Add PC Delete Delete All Apply Cancel

Deny If you select "Deny" then all clients will be allowed to access Internet accept for the clients in the list below.

Allow If you select "Allow" then all clients will be denied to access Internet accept for the PCs in the list below.

Filter client PCs by IP Fill in "IP Filtering Table" to filter PC clients by IP.

Add PC You can click Add PC to add an access control rule for users by IP addresses.

Remove PC If you want to remove some PCs from the "IP Filtering Table", select the PC you want to remove in the table and then click "Delete Selected". If you want to remove all PCs from the table, just click the "Delete All" button.

Filter client PC by MAC Check "Enable MAC Filtering" to enable MAC Filtering.

Add PC Fill in "Client PC MAC Address" and "Comment" of the PC that is allowed to access the Internet, and then click "Add". If you find any typo before adding it and want to retype again, just click "Reset" and the fields will be cleared.

Remove PC If you want to remove some PC from the "MAC Filtering Table", select the PC you want to remove in the table and then click "Delete Selected". If you want to remove all PCs from the table, just click the "Delete All" button. If you want to clear the selection and re-select again, just click "Reset".

Click at the bottom of the screen to save the above configuration.

URL block

You can block access to some Web sites from particular PCs by entering a full URL address or just keywords of the Web site.

Status Wizard Wireless Settings Firewall Advanced Settings Toolbox Choose your language Enable DMZ DoS Access URL block You can block access to certain Web sites from a particular PC by entering either a full URL address or just a keyword of the Web site. Enable URL block URL /Keyword : Add Reset Current URL Blocking Table NO. URL /Keyword Select Delete Delete All Reset Apply Cancel

Enable URL Blocking Enable/disable URL Blocking

Add URL Keyword Fill in "URL/Keyword" and then click "Add". You can enter the full URL address or the keyword of the web site you want to block.

Remove URL Keyword If you want to remove some URL keywords from the "Current URL Blocking Table", select the URL keyword you want to remove in the table and then click "Delete Selected". If you want remove all URL keywords from the table, just click "Delete All" button. If you want to clear the selection and re-select again, just click "Reset".

Click at the bottom of the screen to save the above configurations

14 Advanced Settings

Network Address Translation (NAT) allows multiple users at your local site to access the Internet through a single Public IP Address or multiple Public IP Addresses. NAT provides Firewall protection from hacker attacks and has the flexibility to allow you to map Private IP Addresses to Public IP Addresses for key services such as Websites and FTP. Select Disable to disable the NAT function.

Port Forwarding

Port Forwarding allows you to re-direct a particular range of service port numbers (from the Internet/WAN Port) to a particular LAN IP address. It helps you to host servers behind the router NAT firewall.

Status Wizard Wireless Settings Firewall Advanced Settings Toolbox Choose your language NAT Enable Port Forwarding Special Applications Update Quality of Service Entries in this table allow you to automatically redirect common network services to a specific machine behind the NAT firewall. These settings are only necessary if you wish to host some sort of server like a web server or mail server on the private local network behind your Gateway's NAT firewall. Enable Port Forwarding Local IP Type Port Range Comment Both Add Reset Current Port Forwarding Table: NO. Local IP Type Port Range Comment Select Delete Delete All Reset Apply Cancel

Enable Port Forwarding Enable Port Forwarding

Local IP This is the local IP of the server behind the NAT firewall.

Type This is the protocol type to be forwarded. You can choose to forward "TCP" or "UDP" packets only, or select "both" to forward both "TCP" and "UDP" packets.

Port Range The range of ports to be forward to the private IP.

Comment description of this setting.

Add Port Forwarding Fill in the "Private IP", "Type", "Port Range" and "Comment" of the setting to be added and then click "Add". Then this Port Forwarding setting will be added into the "Current Port Forwarding Table" below.

Remove Port Forwarding If you want to remove a Port Forwarding setting from the "Current Port Forwarding Table", select the Port Forwarding setting that you want to remove in the table and then click "Delete Selected". If you want to remove all Port Forwarding settings from the table, just click "Delete All" button. Click "Reset" will clear your current selections.

Special Applications

Some applications require multiple connections, such as Internet games, video Conferencing, Internet telephony and others. In this section you can configure the router to support multiple connections for these types of applications.

Enable Trigger Port Enable the Special Application function.

TCP Port to open This is the range of TCP port numbers for this particular application.

UDP Port to Open This is the range of UDP port numbers for this particular application.

Status Wizard Wireless Settings Firewall Advanced Settings Toolbox Choose your language NAT Enable Port Forwarding Special Applications UPnP Quality of Service Some applications require multiple connections, such as Internet gaming, video conferencing, Internet telephony and others. These applications cannot work when Network Address Translation (NAT) is enabled. If you need to run applications that require multiple connections, specify the port normally associated with an application in the "Trigger Port" field, select the protocol type as TCP or UDP, then enter the public ports associated with the trigger port to open them for inbound traffic. Enable Trigger port IP Address TCP Port to Open UDP Port to Open Comment 0 0 0 0 Popular Applications: Select an application Add Add Reset Current Trigger-Port Table NO. IP Address TCP Port to Open UDP Port to Open Comment Select Delete Delete All Reset Apply Cancel

Comment The description of this setting.

Popular applications This section lists the more popular applications that require multiple connections. Select an application from the Popular Applications selection. Once you have selected an application, select a location (1-10) in the Copy to selection box and then click the Copy to button. This will automatically list the Public Ports required for this popular application in the location (1-10) you specified.

Add Special Application Fill in the "Trigger Port", "Trigger Type", "Public Port", "Public Type", "Public Port" and "Comment" of the setting to be added and then click "Add". The Special Application setting will be added into the "Current Trigger-Port Table" below. If you happen to make a mistake, just click "Clear" and the fields will be cleared.

Delete If you want to remove Special Application settings from the "Current Trigger-Port Table", select the Special Application settings you want to remove in the table and then click "Delete Selected". If you want remove all Special Application settings from the table, just click the "Delete All" button. Click "Reset" will clear your current selections.

UPnP

With UPnP, all PCs in you Intranet will discover this router automatically, so you don't have to configure your PC and it can easily access the Internet through this router.

Status Wizard Wireless Settings Firewall Advanced Settings Toolbox Choose your language NAT Enable Port Forwarding Special Applications UPnP Quality of Service Universal Plug and Play is designed to support zero-configuration, "invisible" networking, and automatic discovery for a range of device from a wide range of vendors. With UPnP, a device can dynamically join a network, obtain an IP address and learn about the presence and capabilities of other devices all automatically. Devices can subsequently communicate with each other directly. UPnP: : Enable Disable Apply Cancel

UPnP Feature You can enable or Disable the UPnP feature here. After you enable the UPnP feature, all client systems that support UPnP, like Windows XP, can discover this router automatically and access the Internet through this router without having to configure anything. The NAT Traversal function provided by UPnP can let applications that support UPnP connect to the internet without having to configure the virtual server sections.

QoS

QoS can let you classify Internet application traffic by source/destination IP address and port number. You can assign priority for each type of application and reserve bandwidth for it. The packets of applications with higher priority will always go first. Lower priority applications will get bandwidth after higher priority applications get enough bandwidth. This can let you have a better experience in using critical real time services like Internet phone, video conference ...etc. All the applications not specified by you are classified as rule name "Others". The rule with a smaller priority number has a higher priority; the rule with a larger priority number has a lower priority. You can adjust the priority of the rules by moving them up or down.

Status Wizard Wireless Settings Firewall Advanced Settings Toolbox Choose your language NAT Enable Port Forwarding Special Applications UPnP Quality of Service Quality of Service (QoS) refers to the capability of a network to provide better service to selected network traffic. The primary goal of QoS is to provide priority including dedicated bandwidth, controlled jitter and latency (required by some real-time and interactive traffic), and improved loss characteristics. Also important is making sure that providing priority for one or more flows does not make other flows fail. Enable QoS Current QoS Table Priority Rule Name Upload Bandwidth Download Bandwidth Select Add Edit Delete Delete All Move Up Move Down Apply Cancel

Enable/Disable QoS You can check "Enable QoS" to enable QoS functionality for the WAN port.

Add a QoS rule into the table Click "Add" then enter a form of the QoS rule. Click "Apply" after filling out the form the rule will be added into the table.

Remove QoS rules from the table If you want to remove QoS rules from the table, select the QoS rules you want to remove in the table and then click "Delete Selected". If you want remove all QoS rules from the table, just click the "Delete All" button. Clicking "Reset" will clear your current selections.

Edit a QoS rule Select the rule you want to edit and click "Edit", then enter the detail form of the QoS rule. Click "Apply" after editing the form and the rule will be saved.

Adjust QoS rule priority You can select the rule and click "Move Up" to make its priority higher. You also can select the rule and click "Move Down" to make its priority lower.

15 TOOLBOX Settings

Sitecom Cloud Security

Antivirus software alone is not safe enough. You can now benefit from additional built-in security in your modem or router. Protect all devices in your home network against cybercrime while browsing. Activated automatically, your network and devices are better secured than ever before.

Your Sitecom device comes with a 6 month free Sitecom cloud security subscription.

After you have set up your Sitecom device for internet access, open the webbrowser and enter http://www.sitecomcloudsecurity.com in the address bar.

If the device has been properly configured the following web page should be shown.

Sitecom Cloud Security Congratulations, you can now surf safely How many devices in your home use the Internet? Do you have a Mac, smartphone, tablet, or game console next to your Windows PC? All these devices have an Internet connection and all are susceptible to actions by cybercriminals. Sitecom Cloud Security protects all these devices against viruses, phishing and fraud, without you having to worry about it. ✓ Antivirus and Antimalware ? ✓ Antiphishing ? ✓ Protection against unsafe websites ? ✗ Blocking of online advertisements ? Enable No Security Code needed ? Sitecom Cloud Security is automatically activated You are using a free six month subscription, which is not automatically renewed. Did you know that Sitecom Cloud Security has already stopped attacks and threats at 74.8% of the protected home networks? If you want to surf the web lose safety, click here to switch off the protection Continue © 2011 Sitecom. All rights reserved

Here you can see which security features are activated.

The Sitecom Cloud Security service offers the following protection options:

• Anti-Malware
• Anti-Phishing
• Protection against unsafe websites
• Advertisement blocking

With the protection of unsafe websites activated the Sitecom Cloud Security will always check if a website is safe. If it is not safe it will inform you that is not safe to enter.

SITECOM Silocom Cloud Security Unsafe Host http://www.rootkit.com/ This host contains characteristics of an identified security risk. It may compromise your privacy and security, make dangerous changes to your system's settings without your knowledge and consent, or severely degrade your system's performance and stability. Exchanging sensitive or confidential information with this host could also put you at risk for identity theft and/or financial fraud. Back to Safety Recommended I understand that this website may compromise my personal data, proceed anyway. If this website installs malicious software onto your system, please read these instructions about removing the software from your system.

If you still wish to visit this webpage click on 'proceed anyway'. Alternatively click 'Back to Safety' so that your security will not be breached.

If you wish to change your security options or to extend your subscription at any time, open http://www.sitecomcloudsecurity.com from your web browser.

You will be asked for a username and password. These can be found on the backlabel on the bottom of your Sitecom router or modem.

SITECOM Sitecom Cloud Security Configuration Login Username: Password: Login Powered by Hitman Pro technology from OurFlight Copyright © 2011 Sitecom Allrights received UTM/0.9.25 (WL-351 v1081, 1.6)

If the login succeeded you can click on 'Settings' to change your security options.

SITECOM Sitecom Cloud Security Configuration Settings License Security Antivirus software on your computer alone is not safe enough. The built-in security in your router may use cloud-based services to protect all devices in your home network against cybercrime from the internet. You may optionally disable these services. ✓ Antivirus ✓ Protection against unsafe websites ✓ Antiphishing □ Advertisement blocking Splash-screen The splash-screen shows the protection status, once every 8 hours of idle internet usage. Click the button below to enable and bring up the splash-screen, where you can also disable it. Show splash-screen... Apply Powered by Hitmax Pro technology from SunRight Copyright ©2011 Sitecom. All rights reserved UTM/0.5.28 (WL-361 y1001.1.5)

Or click 'License' to renew your subscription.

SITECOM Sitecom Cloud Security Configuration Settings License Subscription Subscription is activated. Expiration date: zendag 31 juli 2011 (149 dagen resterend) Renew subscription Visit subscription provider website to renew subscription. If you have a Key Code and Security Code, enter them in the spaces below and click Activate. Key Code: Security Code: I understand and accept the License Agreement Activate Powered by Hitman Pro technology from SurRight. Copyright © 2011 Sitecom, All rights reserved. UTI/0.8.29 (WL.351 v1601, 1.6)

If you wish to disable to Sitecom cloud security at any time, open the webpage of your Sitecom product and log in with the supplied credentials (these can be

found on the back label on the bottom of your Sitecom device).

Go to Toolbox and select "Sitecom Cloud Security".

wireless gigabit dualband router 300N SITECOM Choose your language Status Wizard 2.4G Wireless Settings 5G Wireless Settings Eirewall Advanced Settings Toolbox Sitecom Cloud Security Password Timecode Remote Firmware Backup-up Reset NOTES Protect all the devices in your home network against cybercrime while browsing with Sitecom Cloud Security! Enable or disable Sitecom Cloud Security : Enable Disable Sitecom Cloud Security : Activate or configure Apply Cancel

Click the "Disable" radio button and click 'Apply' for the settings to take effect.

Password change options

You can change the password required to log into the broadband router's system web-based management. Passwords can contain 0 to 12 alphanumeric characters, and are case sensitive.

Status Wizard Wireless Settings Firewall Advanced Settings Toolbox Choose your language Password Time Zone Remote Firmware Back-up Reset DDNS You can change the password which is required to log on to the router. By default, the password is admin. Passwords can contain 0 to 30 alphanumeric characters, and are case sensitive. Current Password : New Password : Confirm Password : Apply Cancel

Current Password Fill in the current password to allow changing to a new password.

New Password Enter your new password.

Confirm Password Enter your new password again for verification purposes.

Click at the bottom of the screen to save the above configurations

Time Zone

The Time Zone allows your router to base its time on the settings configured here, which will affect functions such as Log entries and Firewall settings.

Status Wizard Wireless Settings Firewall Advanced Settings Toolbox Choose your language Password Time Zone Remote Firmware Back up Reset DDRS Set the time zone of the Wireless Router. This information is used for log entries and firewall settings. Time Zone : (GMT+01:00)Amsterdam, Berlin, Born, Romo, Stockholm, Vienna Time Server Address : 192.43.244.18 Daylight Savings : Enable Time From January - 1 To January - 1 Apply Cancel

Set Time Zone Select the time zone of the country you are currently in. The router will set its time based on your selection.

Time Server Address You can set an NTP server address.

Enable Daylight Savings The router can also take Daylight savings into account. If you wish to use this function, you must check/tick the enable box to enable your daylight saving configuration (below).

Start Daylight Savings Time Select the period in which you wish to start daylight Savings Time

End Daylight Savings Time Select the period in which you wish to end daylight Savings Time

Click at the bottom of the screen to save the above configurations

Remote Management

The remote management function allows you to designate a host in the Internet the ability to configure the Broadband router from a remote site. Enter the designated host IP Address in the Host IP Address field.

Host Address This is the IP address of the host in the Internet that will have management/configuration access to the Broadband router from a remote site. If the Host Address is left 0.0.0.0 this means anyone can access the router's web-based configuration from a remote location, providing they know the password.

Port The port number of the remote management web interface.

Check "Enabled" to enable the remote management function.

Click at the bottom of the screen to save the above configurations.

Firmware Upgrade

This page allows you to upgrade the router's firmware.

Enable or disable Sitecom Auto Upgrade if Enabled the router will automatically check for firmware updates. If a new firmware has been detected a pop/up will appear in the webbrowser and inform the user about the new firmware and the changes and allows to Install the update.

Select Enable or Disable and click apply for the settings to take effect.

Firmware Upgrade This tool allows you to upgrade the Broadband router's system firmware. To upgrade the firmware of your Broadband router, you need to download the firmware file to your local hard disk, and enter that file name and path in the appropriate field on this page. You can also use the Browse button to find the firmware file on your PC.

Once you've selected the new firmware file, click at the bottom of the screen to start the upgrade process.

Backup Settings

The Backup screen allows you to save (Backup) the router's current configuration settings. When you save the configuration setting (Backup) you can re-load the saved configuration into the router through the Restore selection. If extreme problems occur you can use the Restore to Factory Defaults selection, this will set all configurations to its original default settings (e.g. when you first purchased the router).

Use the "Backup" tool to save the Wireless Router's current configuration to a file named "config.bin". You can then use the "Restore" tool to restore the saved configuration to the Wireless Router. Alternatively, you can use the "Restore to Factory Default" tool to force the Wireless Router to perform a system reset and restore the original factory settings. Restore to Factory Default : Reset Backup Settings : Save Restore Settings : Choose File No file chosen Upload

Use the "Backup" tool to save the Broadband router current configuration to a file named "config.bin" on your PC. You can then use the "Restore" tool to restore the saved configuration to the Broadband router. Alternatively, you can use the "Restore to Factory Defaults" tool to force the Broadband router to perform a power reset and restore the original factory settings.

Reset

You can reset the router's system should any problem exist. The reset function essentially re-boots your router's system.

Status Wizard Wireless Settings Firewall Advanced Settings Toolbox Choose your language Password Time Zone Remote Firmware Lock-up Reset OINS In the event the system stops responding correctly or stops functioning, you can perform a reset. Your settings will not be changed. To perform the reset, click on the APPLY button. You will be asked to confirm your decision. The reset will be completed when the LED Power light stops blinking. Apply

DDNS

DDNS allows you to map the static domain name to a dynamic IP address. You must get an account, password and your static domain name from the DDNS service providers. This router supports DynDNS, TZO and other common DDNS service providers.

Status Wizard Wireless Settings Firewall Advanced Settings Toolbox Choose your language Password Time Zone Remote Firmsare Back-up Reset DDNS DDNS allows users to map a static domain name to a dynamic IP address. You must get an account, password and your static domain name from the DDNS service provider. Dynamic DNS : Enable Disable Provider : DynDNS Domain Name : Account / E-mail : Password / Key : Apply Cancel

Enable/Disable Enable or disable the DDNS function of this router

Provider Select a DDNS service provider

Domain name Fill in your static domain name that uses DDNS

Account/E-mail The account that your DDNS service provider assigned to you

Password/Key The password you set for the DDNS service account above

Click at the bottom of the screen to save the above configurations.