WL-341 - Router SITECOM - Free user manual and instructions

USER MANUAL WL-341 SITECOM

Wireless Broadband router

(802.11bgn draft 2.0)

Front view of a white wireless router with four ports and a yellow connector (no visible text or labels)

User Manual

Revision: 1

TABLE OF CONTENTS

1 KEY FEATURES.... 4
2 PACKAGE CONTENTS.... 5
3 PRODUCT LAYOUT 6
4 NETWORK + SYSTEM REQUIREMENTS 8
5 WL-340/WL-341 PLACEMENT 8
6 SETUP LAN, WAN 9
7 PC NETWORK ADAPTER SETUP (WINDOWS XP) 10
8 BRING UP WL-340/WL-341 12
9 INITIAL SETUP WL-340/WL-341 12
10 CONFIGURATION WIZARD.... 19
11 WIRELESS SETTINGS 21
12 FIREWALL SETTINGS 32
13 ADVANCED SETTINGS 38
14 TOOLBOX SETTINGS 46

Introduction

Congratulations on your purchase of the WL-340/WL-341 Wireless Network Broadband Router. The WL-340/WL-341 is compliant with draft 802.11n v2.0 and up to 6 times faster than standard 802.11g based routers while still being compatible with 802.11g & 802.11b gadgets. The WL-340/WL-341 is not only a Wireless Access Point, but also doubles as a 4-port full-duplex Switch that connects your wired-Ethernet devices together.

At 300 Mbps wireless transmission rate, the Access Point built into the Router uses advanced MIMO (Multi-Input, Multi-Output) technology to transmit multiple streams of data in a single wireless channel, giving you seamless access to multimedia content. Robust RF signals travel farther, eliminating dead spots and extending network range. For data protection and privacy, the WL-340/WL-341 encodes all wireless transmissions with WEP, WPA, or WPA2 encryption.

With an inbuilt DHCP Server & powerful SPI firewall the WL-340/WL-341 protects your computers against intruders and most known Internet attacks but provides safe VPN pass-through. With the incredible speed and the QoS function of 802.11n(draft2.0), the WL-340/WL-341 is ideal for media-centric applications like streaming video, gaming, and VoIP telephony to run multiple media-intense data streams through the network at the same time, with no degradation in performance.

1 Key Features

Features Advantages
Incredible Data Rate up to 300Mbps*	Heavy data payloads such as MPEG video streaming
IEEE 802.11n draft 2.0 Compliant and backward compatible with 802.11b/g	Fully Interoperable with IEEE 802.11b / IEEE802.11g compliant devices with legacy protection
Four 10/100 Mbps Fast Switch Ports (Auto-Crossover)	Scalability, extend your network.
Firewall supports Virtual Server Mapping, DMZ, IP Filter, ICMP Blocking, SPI.	Avoids the attacks of Hackers from Internet.
Support 802.1x authenticator, 802.11i (WPA/WPA2, AES), VPN pass-through	Provide mutual authentication (Client and dynamic encryption keys to enhance security)

* Theoretical wireless signal rate based on IEEE standard of 802.11a, b, g, n chipset used. Actual throughput may vary. Network conditions and environmental factors lower actual throughput rate. All specifications are subject to change without notice.

2 Package Contents

Open the package carefully, and make sure that none of the items listed below are missing. Do not discard the packing materials, in case of return; the unit must be shipped back in its original package.

1. WL-340/WL-341 Router
2. 220V\~240V Power Adapter
3. Quick Install Guide
4. CD (User's Manual)
5. Warranty card
6. UTP cable

3 Product Layout

White wireless router with four Ethernet ports and a yellow connector on the front panel (no visible text or symbols)

Port Description
Power connector	Blinks on traffic for specific LAN PORT
WAN[Yellow]	Connect the cable from you ADSL/Cable modem to this port
LAN[Grey]	Connect the cable from your PC's or network devices to this port

Back label

The back label describes the corresponding LED indications and port functionality.

To access the router configuration, type the following IP address in your internet browser: 192.168.0.1 Username: admin / Password: admin To make a wireless connection with this router, choose the network: Serial No.: WPA2 code: SITECOM Model No: WL-341 v1 001 CE! 8716502 019809 Made in China Designed in Europe Press 2 sec. = WPS mode Press 10 sec. = Reset Press 15 sec. = Factory default

LED Description
POWER Lights up when powered ON. Blinks on TEST/RESET
WLAN	Lights up in Blue when WLAN is enabled. Blinks on traffic
LINK/ACTIVY Blinks on traffic for specific LAN PORT
WPS BUTTON	Press 2 seconds for WPS modePress 10 seconds to reset the routerPress 15 Seconds to reset the router to factory defaults.

4 Network + System Requirements

To begin using the WL-340/WL-341, make sure you meet the following as minimum requirements:

• PC/Notebook.
• Operating System – Microsoft Windows XP/2000/VISTA.
  • 1 Free Ethernet port.
• WiFi card/USB dongle (802.11 b/g/n) – optional.
• External xDSL (ADSL) or Cable modem with an Ethernet port (RJ-45).
  • PC with a Web-Browser (Internet Explorer, Safari, Firefox, Opera).
• Ethernet compatible CAT5 cables.

5 WL-340/WL-341 Placement

You can place the WL-340/WL-341 on a desk or other flat surface, or you can mount it on a wall. For optimal performance, place your Wireless Broadband Router in the center of your home (or your office) in a location that is away from any potential source of interference, such as a metal wall or microwave oven. This location must be close to a power connection and your ADSL/Cable modem.

6 Setup LAN, WAN

WAN connection:

WAN MODEM Click ROUTER

LAN connection:

LAN ROUTER

7 PC Network Adapter setup ( Windows XP)

• Enter [Start Menu] → select [Control panel] → select [Network].

Network Connections File Edit View Favorites Tools Advanced Help Search Folders Address Network Connections Network Tasks Create a new connection Set up a home or small office network. Change Windows Firewall settings Internet Gateway Internet Connection Connected Exclusive Connection LAN or High-Speed Internet Wireless Network Connection Not Connected, Provided IDEWR PRO/Wireless SP4562 Local Area Connection Connected, Provided Readtek RTL8160/8111 PCE-E ... 1394 Connection Connected, Provided 1394 Net Provider See Also Network Troubleshooter Other Places Control Panel My Network Places

- Select [Local Area Connection]) icon =>select [properties]

Local Area Connection Connected, Firewalled Realtek Disable Status Repair Bridge Connections Create Shortcut Delete Rename Properties

- Select [Internet Protocol (TCP/IP)] =>Click [Properties].

Local Area Connection Properties General | Authentication | Advanced | Connect using: Realtek RTL8168/8111 PCI-E Gigabi Configure... This connection uses the following items: Network Monitor Driver Microsoft TCP/IP version 6 Internet Protocol (TCP/IP) Install... Uninstall Properties Description Transmission Control Protocol/Internet Protocol. The default wide area network protocol that provides communication across diverse interconnected networks. Show icon in notification area when connected Notify me when this connection has limited or no connectivity OK Cancel

Internet Protocol (TCP/IP) Properties General Alternate Configuration You can get IP settings assigned automatically if your network supports this capability. Otherwise, you need to ask your network administrator for the appropriate IP settings. Obtain an IP address automatically a Use the following IP address: IP address: Subnet mask: Default gateway: Obtain DNS server address automatically a Use the following DNS server addresses: Preferred DNS server: Alternate DNS server: Advanced... OK Cancel

- Select the [General] tab.

a. WL-340/WL-341 supports [DHCP] function, please select both [Obtain an IP address automatically] and [Obtain DNS server address automatically].

8 Bringing up the WL-340/WL-341

Connect the supplied power-adapter to the power inlet port and connect it to a wall outlet. The WL-340/WL-341 automatically enters the self-test phase.

During self-test phase, the Power LED will be lit continuously to indicate that this product is in normal operation.

9 Initial Setup WL-340/WL-341

LOGIN procedure

1. Click to OPEN your browser (e.g. Internet Explorer).

1. Type http://192.168.0.1 in the address bar and press [Enter].

Blank Page - Windows Internet Explorer http://192.168.0.1/ File Edit View Favorites Tools Help Connecting... Connect to 192.169.0.1 The server 136.169.0.1 of Default: admin/admin requires a username and password. Warning: This server is requesting that your username and password be sent in an insecure manner (basic authentication without a secure connection). User name: Password: □ Remember my password OK Cancel

1. Type user name and password (default is admin/admin).

Connect to 192.168.0.1 The server 192.168.0.1 at Default: admin/admin requires a username and password. Warning: This server is requesting that your username and password be sent in an insecure manner (basic authentication without a secure connection). User name: admin Password: •••••• ✓ Remember my password OK Cancel

1. Click OK.
2. You will see the home page of the WL-340/WL-341.

Sitecom wireless broadband router Wl. 341 - Micilla Wireless Risland, Rogenien, Bred, Goachidroks, RayWixers, Extra Help http://052.968.0.1/index.htm Kleist betoche: Am de slag, Laubite news, Gratis Hotmail, Koppelingen antipossen, Windows Media, Windows 300N ROUTER SITECOM WIRELESS Status Wizard Wireless Settings Forward Advanced Settings Toolbox Choose your language System Status DHCP Server Reserve Status Internet Status DHCP Status Info You can use the Status page to monitor the connection status for the WAY/UX interfaces, firmware and hardware version numbers, any illegal attempts to access your network and information on all DHCP client PCs currently connected to your network. System Model : 300N Wireless Router Runtime : 0day15th 0pm 11s Hardware Version : 01 Serial Number : 3026017.356 Boat Code Version : v0.03 Runtime Code Version : v0.04 (Oct 31 2009 19:19:25) Iber

The System status section allows you to monitor the current status of your router.

The UP time, hardware information, serial number as well as firmware version information is displayed here.

DHCP Server

The DHCP server tab gives you the opportunity to change the IP settings of the WL-340/WL-341.

Sitecom wireless broadband router Wl-341 - Mozilla Firefox Enland Regenlan Rentd Gochatrons Modulators Echo Help http://i92.168.0.1/index.htm Meat besanche Aon de log Loibate nusuv Gstais hswai Kippelogen sampassen Windows Media Windows 300N ROUTER SITECOM WIRELESS Status Wizard Wireless Settings Firewall Advanced Settings Toolbox Choose your language System Status DHCP Server Device Status Internet Status DHCP Media Log You can enable the Broadband routers DHCP server to dynamically allocate IP Addresses to your LAN client PCs. The broadband router must have an IP Address for the Local Area Network. LAN IP IP Address : 192.168.0.1 IP Subnet Mask : 255.255.255.0 DHCP Server : Enabled Lease Time : Two Days DHCP Server Start IP : 192.168.0.100 End IP : 192.168.0.200 Domain Name : Sitecom Apply Cancel http://i92.168.0.1/nn.stn

IP address 192.168.0.1. It is the router's LAN IP address (Your LAN clients default gateway IP address).

IP Subnet Mask 255.255.255.0 Specify a Subnet Mask for your LAN segment.

DHCP Server Enabled by default. You can enable or disable the DHCP server. When DHCP is disabled no ip-addresses are assigned to clients and you have to use static ip-addresses. When DHCP server is enabled your computers will be assigned an ip-address automatically until the lease time expires.

Lease Time Forever. In the Lease Time setting you can specify the time period that the DHCP lends an IP address to your LAN clients. The DHCP will change

your LAN client's IP address when this time threshold period is reached.

Start IP/End IP You can select a particular IP address range for your DHCP server to issue IP addresses to your LAN Clients.

Note: default IP range 192.168.0.100 192.168.0.199. If you want your PC(s) to have a static/fixed IP address, then you'll have to choose an IP address outside this IP address Pool

Domain Name You can specify a Domain Name for your LAN. Or just keep the default (Sitecom).

Click at the bottom of this screen to save any changes.

Device Status

View the Broadband router's current configuration settings. Device Status displays the configuration settings you've configured in the Wizard / Basic Settings / Wireless Settings section.

Sitecom wireless broadband router WL-341 - Mozilla Firefox England Georgia Iceland Madagascar Libya Egypt Help Fleet besoche: Aon de slag Loebate news Global Hostwai Koppelinom passengers Windows Media Windows 300N ROUTER WIRELESS SITECOM Status Wizard Wireless Settings Firewall Advanced Settings Toolbox Choose your language System Status DHCP Server Device Status Internet Status DHCP Status Log View the current setting status of this device. Wireless Configuration Mode: AP ESSID: Starcom241D42 Channel: 11 Security: WPA pre-shared kit BSSID: 00-23-09-24-10-42 LAN Configuration IP Address: 192.168.5.1 Subset Mask: 255.255.258.0 DHCP Server: Enabled MAC Address: 00-23-09-24-10-42

Internet Status

This page displays whether the WAN port is connected to a Cable/DSL connection. It also displays the router's WAN IP address, Subnet Mask, and ISP Gateway as well as MAC address, the Primary DNS. Press Renew button to renew your WAN IP address.

Sitecom wireless broadband router WL-341 - Mozilla Firefox Bestand Regenlan Entd Gezeichnet Modulators Echo Help http://152.168.0/ Index.htm Meat headache Aon de slag Lachite nusus Global Hostnal Koppelingen anpassen Windows Media Windows 300N ROUTER WIRELESS SITECOM Status Wizard Wireless Settings Firewall Advanced Settings Toolbox Choose your language Systemi Status DHCP Server Device Status Internet Status DHCP Status Log View the current internet connection status and related information. Attach IP Protocol : Dynamic IP Address IP Address : 0.0.0.0 Subnet Mask : 0.0.0.0 Default Gateway : 0.0.0.0 MAC address : 00:23-09:24-10-43 Primary DNS : 0.0.0.0 Fislow

DHCP Client Status

This page shows all DHCP clients (LAN PCs) currently connected to your network. The table shows the assigned IP address, MAC address and expiration time for each DHCP leased client. Use the Refresh button to update the available information.

Sitecom wireless broadband router WL-341 - Mozilla Firefox BeLand, Beogen, Need, Geschendix, Sladeners, Echo Help http://192.168.0.1/index.htm 300N ROUTER SITECOM WIRELESS Status Wizard Wireless Settings Firewall Advanced Settings Toolbox Choose your language System Status DHCP Server Device Matrix Internet Status DHCP Status Log This table shows the assigned IP address, MAC address and expiration time for each DHCP leased client. IP address MAC address 192.168.0.100 00:12:23:40:00:70 192.168.0.101 00:00:16:4A:83:91 Refresh

WL-340/WL-341 Log

View the operation log of the WL-340/WL-341. This page shows the current system log of the Broadband router. It displays any event occurred after system start up. At the bottom of the page, the system log can be saved

to a local file for further processing, the system log can be cleared

or it can be refreshed to get the most updated

information. When the system is powered down, the system log will disappear if not saved to a local file.

Sitecom wireless broadband router WL 341 - Mozilla Firefox Risikand, Begeken, Read, Goohendris, LogMallors, Elex, Help http://192.168.0.1/index.htm 300N ROUTER WIRELESS SITECOM Status Wizard Wireless Settings Firewall Advanced Settings Toolbox Choose your language System Status DHCP Server Device Status Internet Status DHCP Status Log View the system operation information. You can see the system start up time, connection process...etc. here. System Log 08/01/2003 01:08:16 BSCP Client: [VAN]Could not find DHCP daemon to get information 08/01/2003 01:08:14 BSCP Client: [VAN]Send Discover 08/01/2003 01:08:12 BSCP Client: [VAN]Send Discover 08/01/2003 01:08:10 BSCP Client: [VAN]Send Discover 08/01/2003 01:08:08 BSCP Client: [VAN]Send Discover 08/01/2003 01:07:49 BSCP Client: [VAN]Could not find DHCP daemon to get information 08/01/2003 01:07:46 BSCP Client: [VAN]Send Discover 08/01/2003 01:07:44 BSCP Client: [VAN]Send Discover 08/01/2003 01:07:42 BSCP Client: [VAN]Send Discover 08/01/2003 01:07:40 BSCP Client: [VAN]Send Discover 08/01/2003 01:07:37 BSCP Client: [VAN]Could not find DHCP daemon to get information 08/01/2003 01:07:35 BSCP Client: [VAN]Send Discover 08/01/2003 01:07:33 BSCP Client: [VAN]Send Discover 08/01/2003 01:07:31 BSCP Client: [VAN]Send Discover 08/01/2003 01:06:53 BSCP Client: [VAN]Could not find DHCP daemon to get information 08/01/2003 01:06:50 BSCP Client: [VAN]Send Discover 08/01/2003 01:06:48 BSCP Client: [VAN]Send Discover 08/01/2003 01:06:45 BSCP Client: [VAN]Send Discover 08/01/2003 01:06:44 BSCP Client: [VAN]Send Discover 08/01/2003 01:06:34 BSCP Client: [VAN]Could not find DHCP daemon to get information http://[e-mail]

10 Configuration Wizard

Click Wizard to configure the router. The Setup wizard will now be displayed; check that the modem is connected and click Next.

Sitecom wireless broadband router WL-341 - Mozilla Firefox Beizand Reberken Need Geschredens Skoduijors Echo Help http://162.168.0.1/index.htm Please choose: Ain de slag Loebate neueve Grobe Hotwar Koppelnogen anpassen Windows Media Windows 300N ROUTER SITECOM WIRELESS Status Wizard Wireless Settings Firewall Advanced Settings Toolbox Choose your language Setup Wizard The Setup Wizard will guide you step by step through a basic configuration procedure. next

Select your country from the Country list. Select your internet provider. Click Next.

Sitecom wireless broadband router WL-341 - Mozilla Firefox Bestand Recognien Next Geschwindis Modulators Echo Help http://162.168.0.x/index.htm Meet besanche Ask de tag Laddite nauve Goisie Hotmail Koppelingen anpassers Windows Media Windows 300N ROUTER WIRELESS SITECOM Status Wizard Wireless Settings Firewall Advanced Settings Toolbox Choose your language Select your country and ISP Country : Netherlands Service : Android Provider Hardware Configurant Select ISP ADSL Provider (all workspaces neu x Speedouch Home modem) ADSL Provider met Speedouch Home modem Label Provider (android gebruikerman en wachuvant) Label Provider met geobylinkungen an wachuvant Android Provider (Software Infrastructure) previous next User

Depending on the chosen provider, you may need to enter your user name and password, MAC address or hostname in the following window. After you have entered the correct information, click Next.

Sitecom wireless broadband router WL 341 - Mozilla Firefox Bestand Recognien Need Geschäftsris Modulators Extra Help http://192.168.0.1/indias.sta Market besanche Aon de slog Loebite neues Grobe Hotwar Koppelingen anpassen Windows Media Windows 300N ROUTER WIRELESS SITECOM Status Wizard Wireless Settings Firewall Advanced Settings Toolbox Choose your language Select your country and ISP Login Method: FPP over Ethernet Username: Password: Confirm Password: Service: MTU: 1452 (512<=MTU Value<=1492) Connection Type: Automatic Connect/Discount Idle Time: 20 (1-1000 Minutes) previous Apply Cancel Preview

Click APPLY to complete the configuration.

11 Wireless Settings

You can set parameters that are used for the wireless stations to connect to this router. The parameters include Mode, ESSID, Channel Number and Associated Client.

Wireless Function

Sitecom wireless broadband router WL 341 - Mozilla Firefox Bestand Engellem Reel Geschadens Skadjahers Extra Help http://192.168.0.1/index.htm Meist besanche: Aon de slag Lockside news Goiba Hotwai Koppelingen senpasses Windows Media Windows 300N ROUTER SITECOM WIRELESS Status Wizard Wireless Settings Firewall Advanced Settings Toolbox Choose your language Enable Basic Advanced Security AI MPS The gateway can be quickly configured as a wireless access point for roaming clients by setting the SSD and channel number. It also supports data encryption and client filtering. Enable or disable Wireless module function : Enable Disable Apply Beig net het lohen van 192.168.0.1

Enable or Disable Wireless function here. Click Apply and wait for module to be ready & loaded.

Basic Settings

Sitecom wireless broadband router WL-341 - Mozilla Firefox Gealand Recognien Rees Geschwindia Regulators Eyle Help Perat besanche: Aon de slag Laubate hniaud Global Hotswol Koppelingen sempassen Windows Media Windows 300N ROUTER WIRELESS Status Wizard Wireless Settings Firewall Advanced Settings Toolbox Choose your language Enable Basic Advanced Security ACL WPS This page allows you to define ESSID, and Channel for the wireless connection. These parameters are used for the wireless stations to connect to the Access Point. Band: 2.4 GHz (E+G+N) ESSID: Sitecom®41.042 Channel: 11 Channel Bandwidth 20/40MHz Extension Channel: ? Apply Cancel http://152.168.0.1/eibasic.shn

Band Allows you to set the AP fixed at 802.11b or 802.11g mode. You can also select B+G mode to allow 802.11b and 802.11g clients at the same time.

ESSID This is the name of the wireless signal which is broadcasted. All the devices in the same wireless LAN should have the same ESSID.

Channel The channel used by the wireless LAN. All devices in the same wireless LAN should use the same channel.

Channel Bandwidth Allows you to choose the channel bandwidth 20 MHz or 20/40 MHz.

Extension Channel Allows you to select the extension channel when Channel bandwidth is set to 20/40 MHz.

Advanced Settings

This tab allows you to set the advanced wireless options. The options included are Authentication Type, Fragment Threshold, RTS Threshold, Beacon Interval, and Preamble Type. You should not change these parameters unless you know what effect the changes will have on the router.

Sitecom wireless broadband router Wt. 341 - Mozilla Firefox Gesland, Begeken, Reid, Gezeichnet, Regulators, Extra Help http://192.168.0.1/index.stn 300N ROUTER WIRELESS SITECOM Status Wizard Wireless Settings Firewall Advanced Settings Toolbox Choose your language Enable Master Advanced Security ACL MPS These settings are only for more technically advanced users who have a sufficient knowledge about wireless LAN. These settings should not be changed unless you know what affect the changes will have on your broadband router. Fragment Threshold : 2346 (250-2346) RTS Threshold : 2347 (0-2347) Beacon Interval : 100 (20-1023 ms) DTM Period : 1 (1-10) Preamble Type : Long Preamble Short Preamble Broadcast FSSID : Enable Disable Transmit Burst Mode : Enable Disable B02.11g protection : Enable Disable WNM : Enable Disable Apply Cancel http://192.168.0.1/wkndome.stn

Fragment Threshold "Fragment Threshold" specifies the maximum size of a packet during the fragmentation of data to be transmitted. If you set this value too low, it will result in bad performance.

RTS Threshold When the packet size is smaller then the RTS threshold, the wireless router will not use the RTS/CTS mechanism to send this packet.

Beacon Interval is the interval of time that this wireless router broadcasts a beacon. A Beacon is used to synchronize the wireless network.

Preamble Type The "Long Preamble" can provide better wireless LAN compatibility while the "Short Preamble" can provide better wireless LAN performance.

Broadcast ESSID If you enabled "Broadcast ESSID", every wireless station located within the coverage of this access point can discover this access point easily. If you are building a public wireless network, enabling this feature is recommended. Disabling "Broadcast ESSID" can provide better security.

802.11g protection: It is recommended to enable the protection mechanism. This mechanism can decrease the rate of data collision between 802.11b and 802.11g wireless stations. When the protection mode is enabled, the throughput of the AP will be a little lower due to a lot of frame-network that is transmitted.

WMM WiFi Multi Media if enabled supports QoS for experiencing better audio, video and voice in applications.

Security

This Access Point provides complete wireless LAN security functions, included are WEP, IEEE 802.11x, IEEE 802.11x with WEP, WPA with pre-shared key and WPA with RADIUS. With these security functions, you can prevent your wireless LAN from illegal access. Please make sure your wireless stations use the same security function, and are setup with the same security key.

Disable

When you choose to disable encryption, it is very insecure to operate the WL-341.

300N ROUTER WIRELESS SITECOM Status Wizard Wireless Settings Password Advanced Settings Toolbar Choose your language Enable Basic Advanced Security ACL WPS This page allows you setup the wireless security. Turn on WEP or WPA by using Encryption Keys could prevent any unauthorized access to your wireless network. Encryption : Disable Enable ID02.1x Authentication Apply Cancel

WEP

When you select 64-bit or 128-bit WEP key, you have to enter WEP keys to encrypt data. You can generate the key by yourself and enter it. You can enter four WEP keys and select one of them as a default key. Then the router can receive any packets encrypted by one of the four keys.

300N ROUTER WIRELESS SITECOM Status: Wizard Wireless Settings Format Advanced Settings Help Box Choose your language Enable Base Advanced Security ALL Nts This page allows you to setup the wireless security. Turn on WEP or MPA by using Encryption Keys could prevent any unauthorized access to your wireless network. Encryption: WEP Key Length: 64 bit Key Type: ASCII (5 characters) Default Key: Key 1 Encryption Key 1: Encryption Key 2: Encryption Key 3: Encryption Key 4: Enable 002.1x Authentication Apply Cancel

Key Length You can select the WEP key length for encryption, 64-bit or 128-bit. The larger the key will be the higher level of security is used, but the throughput will be lower.

Key Type You may select ASCII Characters (alphanumeric format) or Hexadecimal Digits (in the "A-F", "a-f" and "0-9" range) to be the WEP Key.

Key1 - Key4 The WEP keys are used to encrypt data transmitted in the wireless network. Use the following rules to setup a WEP key on the device. 64-bit WEP: input 10-digits Hex values (in the "A-F", "a-f" and "0-9" range) or 5-digit ASCII character as the encryption keys. 128-bit WEP: input 26-digit Hex values (in the "A-F", "a-f" and "0-9" range) or 13-digit ASCII characters as the encryption keys.

Click at the bottom of the screen to save the above configurations. You can now configure other sections by choosing Continue, or choose Apply to apply the settings and reboot the device.

WPA Pre-shared Key

Wi-Fi Protected Access (WPA) is an advanced security standard. You can use a pre-shared key to authenticate wireless stations and encrypt data during communication. It uses TKIP or CCMP (AES) to change the encryption key frequently. So the encryption key is not easy to be cracked by hackers. This is the best security available.

300N ROUTER WIRELESS Status Wizard Wireless Settings Review Advanced Settings Tools Choose your language Google Band Advanced Security Web Help This page allows you to setup the wireless security. Turn on WSP or WPA by using Enovation Keys could prevent any unauthorized access to your wireless network. Encryption: WPA pre-shared key by WPA Type: ○WPA(TUP) ○WPA(ZAES) ○WPA2 Mixed Pre-shared Key Type: Passphrase Pre-sharedKey: Apply Cancel

WPA-Radius

Wi-Fi Protected Access (WPA) is an advanced security standard. You can use an external RADIUS server to authenticate wireless stations and provide the session key to encrypt data during communication. It uses TKIP or AES to change the encryption key frequently. Press Apply button when you are done.

300N ROUTER WIRELESS SITECOM Status Wizard Wireless Settings Firewall Advanced Settings Toolbox Choose your language Trade Basic Not Provided Security ACL WPS This page allows you setup the wireless security. Turn on WEP or WPA by using Encryption Keys could prevent any unauthorized access to your wireless network. Encryption: WPA RADIUS WPA Type: WPGCTE(P) WPGS(AFS) WPG2 Mixed. RADIUS Server IP Address: RADIUS Server Port : 1812 RADIUS Server Password : Apply Cancel

ACL

This wireless router supports MAC Address Control, which prevents unauthorized clients from accessing your wireless network.

Sitecom wireless broadband router WI -341 : Mozilla Firefox Bestand Regelien Besti Geschiedens Bladixers Echo Help http://192.168.0.1/index.htm 300N ROUTER SITECOM WIRELESS Status Wizard Wireless Settings Firewall Advanced Settings Toolbox Choose your language Enable Reset Advanced Security ACL WPS For security reason, the Access Point features MAC Address Filtering which only allows authorized MAC Addresses to associate with the Access POINT. MAC Address Filtering Table Enable Wireless Access Control NO. MAC address 1 00 : 00 : 00 : 00 : 00 : 00 2 00 : 00 : 00 : 00 : 00 : 00 3 00 : 00 : 00 : 00 : 00 : 00 4 00 : 00 : 00 : 00 : 00 : 00 5 00 : 00 : 00 : 00 : 00 : 00 6 00 : 00 : 00 : 00 : 00 : 00 7 00 : 00 : 00 : 00 : 00 : 00 8 00 : 00 : 00 : 00 : 00 : 00 9 00 : 00 : 00 : 00 : 00 : 00 http://192.168.0.1/wkontrol.stm

Enable wireless access control Enables the wireless access control function

Adding an address into the list Enter the "MAC Address" of the wireless station to be added and then click "Apply". The wireless station will now be added into the "MAC Address Filtering Table" below.

Remove an address from the list If you want to remove a MAC address from the "MAC Address Filtering Table", select the MAC address that you want to remove in the list and empty the fields.

Click at the bottom of the screen to save the above configurations. You can now configure other sections by choosing Continue, or choose Apply to apply the settings and reboot the device.

WPS

Wi-Fi Protected Setup (WPS) is the simplest way to establish a connection between the wireless clients and the wireless router. You don't have to select the encryption mode and fill in a long encryption passphrase every time when you try to setup a wireless connection. You only need to press a button on both wireless client and wireless router, and WPS will do the rest for you.

The wireless router supports two types of WPS: WPS via Push Button and WPS via PIN code. If you want to use the Push Button, you have to push a specific button on the wireless client or in the utility of the wireless client to start the WPS mode, and switch the wireless router to WPS mode. You can simply push the WPS button of the wireless router, or click the 'Start to Process' button in the web configuration interface. If you want to use the PIN code, you have to know the PIN code of the wireless client and switch it to WPS mode, then fill-in the PIN code of the wireless client through the web configuration interface of the wireless router.

Sitecom wireless broadband router WI-341 - Mozilla Firefox Enland, Beiglun, Reid, Grochstets, Rgblaziers, Egris Help Please choose: Ano de Sag Lokobte rnaus Griola Hotmail Koppeligen amposers Windows Media WINS 300N ROUTER SITECOM WIRELESS Status: Wizard Wireless Settings Firewall Advanced Settings Toolbox Choose your language Enable Basic Advanced Security API WPS WPS : ☑ enable Wi-Fi Protected Setup Information WPS Current Status : unConfigured Sell Pin Code : 12845670 SSID : 5becom241042 Authentication Mode : WPS pre-shared key Passphrase Key : 24004275 WPS Via Push Button : Start to Process WPS Via PIN : Start to Process http://192.168.01/index.htm

WPS Check the box to enable WPS function and uncheck it to disable the WPS function.

WPS Current Status If the wireless security (encryption) function of this wireless router is properly set, you'll see a 'Configured' message here. Otherwise, you'll see 'UnConfigured'.

Self Pin Code This is the WPS PIN code of the wireless router. You may need this information when connecting to other WPS-enabled wireless devices.

SSID This is the network broadcast name (SSID) of the router.

Authentication Mode It shows the active authentication mode for the wireless connection.

Passphrase Key It shows the passphrase key that is randomly generated by the wireless router during the WPS process. You may need this information when using a device which doesn't support WPS.

WPS via Push Button Press the button to start the WPS process. The router will wait for the WPS request from the wireless devices within 2 minutes.

WPS via PIN You can fill-in the PIN code of the wireless device and press the button to start the WPS process. The router will wait for the WPS request from the wireless device within 2 minutes.

12 Firewall Settings

The Broadband router provides extensive firewall protection by restricting connection parameters, thus limiting the risk of hacker attacks, and defending against a wide array of common Internet attacks. However, for applications that require unrestricted access to the Internet, you can configure a specific client/server as a Demilitarized Zone (DMZ).

Note: To enable the Firewall settings select Enable and click Apply

DMZ

If you have a client PC that cannot run an Internet application (e.g. Games) properly from behind the NAT firewall, then you can open up the firewall restrictions to unrestricted two-way Internet access by defining a DMZ Host. The DMZ function allows you to re-direct all packets going to your WAN port IP address to a particular IP address in your LAN. The difference between the virtual server and the DMZ function is that the virtual server re-directs a particular service/Internet application (e.g. FTP, websites) to a particular LAN client/server, whereas DMZ re-directs all packets (regardless of services) going to your WAN IP address to a particular LAN client/server.

Sitecom wireless broadband router WL-341 - Mozilla Firefox Risland, Regeken, Reed, Gezelnics, Sladeners, Eylea Help Meist besanche: Aon de slag, Laktate news, Grobe Hatwell, Koppeligen ampasses, Windows Media, Windows 300N ROUTER SITECOM WIRELESS Status: Visit and Wireless Settings Firewall Advanced Settings Toolbox Choose your language Choose DMZ Doc Access URL block If you have a local client PC that cannot run an Internet application properly from behind the NAT firewall, you can open unrestricted two-way Internet access for this client by defining a Virtual DMZ Host. Enable DMZ Public IP Address Client PC IP Address 0:0 0:0 192 168 0:0 Apply Cancel http://152.168.0.1/home.stm

Enable DMZ Enable/disable DMZ

Public IP Address The IP address of the WAN port or any other Public IP addresses given to you by your ISP

Client PC IP Address Enter the IP address of a particular host in your LAN that will receive all the packets originally going to the WAN port/Public IP address above.

Click at the bottom of the screen to save the above configurations.

Denial of Service (DoS)

The Broadband router's firewall can block common hacker attacks, including Denial of Service, Ping of Death, Port Scan and Sync Flood. If Internet attacks occur the router can log the events.

Sitecom wireless broadband router WL-341 - Mozilla Firefox Gealand, Begeken, Kred, Gezschroder, Slogdamer, Esbro Help Perat besche: Aon de Sag, Laubate rnaue, Grotis Hotwal, Koppelingen anpassen, Windows Media, Windows 300N ROUTER WIRELESS SITECOM Status: Wizards Wireless Settings Firewall Advanced Settings Toolbox Choose your language Enable ONS DoS Access SSL block The firewall can block common hacker attacks, including DOS, Discord Ping from WAN and Port Scan. Denial of Service features SPI and Anti-DOS firewall protection: RIP defects: Discard Ping to WAN Interface: Stateful Packet Inspection Packet Fragmentation: TCP Connectors: UDP Session: FTP Service: H.323 Service: TFTP Service: E-mail Alert http://192.168.01/bwless.stm

SPI and Anti-Dos firewall protection blocks basic hacker attacks (DOS, Sync flood, port scan)

RIP defect Allows the user to choose if the router should respond to other RIP compliant devices.

Discard Ping to WAN interface The router's WAN port will not respond to any Ping requests.

Stateful packet inspection allows the user to manually determine which packets should be scanned.

E-mail Alert Enter your email address. Specify your SMTP and POP3 servers, user name, and password.

Connection Policy Enter the appropriate values for TCP/UDP sessions as described in the following table.

Access

You can restrict users from accessing certain Internet applications/services (e.g. Internet websites, email, FTP etc.), Access Control allows users to define the traffic type permitted in your LAN. You can control which PC client can have access to these services.

Sitecom wireless broadband router WL-341 - Mozilla Firefox Global Sweden Goachodena Sweden Optimum Ebara Help http://152.168.0.1/index.htm Present besuchs: Aon de slag Lakhate nuneet Global Hotmail Koppelingen anpassen Windows Media Windows 300N ROUTER SITECOM WIRELESS Status Wizard Wireless Settings Firewall Advanced Settings Toolbox Choose your language Enable DP2 Box Access SSL blocks Access Control allows users to define the traffic type permitted or not permitted in your LAN. You can control which PC uses what services or has access to. If both MAC filtering and IP filtering are enabled, the MAC filtering table will be checked first. Enable MAC filtering Deny Allow Client PC MAC Address Add Reset MAC Filtering table: NO. Client PC MAC Address Select Delete Selected Delete Add Reset Enable IP Filtering Table (up to 20 computers) NO. PC Description PC IP Address Client Service Select Layer

Deny If you select "Deny" then all clients will be allowed to access Internet accept for the clients in the list below.

Allow If you select "Allow" then all clients will be denied to access Internet accept for the PCs in the list below.

Filter client PCs by IP Fill in "IP Filtering Table" to filter PC clients by IP.

Add PC You can click Add PC to add an access control rule for users by IP addresses.

Remove PC If you want to remove some PCs from the "IP Filtering Table", select the PC you want to remove in the table and then click "Delete Selected". If you want to remove all PCs from the table, just click the "Delete All" button.

Filter client PC by MAC Check "Enable MAC Filtering" to enable MAC Filtering.

Add PC Fill in "Client PC MAC Address" and "Comment" of the PC that is allowed to access the Internet, and then click "Add". If you find any typo before adding it and want to retype again, just click "Reset" and the fields will be cleared.

Remove PC If you want to remove some PC from the "MAC Filtering Table", select the PC you want to remove in the table and then click "Delete Selected". If you want to remove all PCs from the table, just click the "Delete All" button. If you want to clear the selection and re-select again, just click "Reset".

Click at the bottom of the screen to save the above configuration.

URL block

You can block access to some Web sites from particular PCs by entering a full URL address or just keywords of the Web site.

Sitecom wireless broadband router Wl -341 - Mozilla Firefox Bestand Regenien Besti Geschiedens Agdweers Echo Help http://192.168.0.1/index.htm 300N ROUTER WIRELESS SITECOM Status Wizard Wireless Settings Firewall Advanced Settings Toolbox Choose your language Enable URL Back Address URL block You can block access to certain Web sites for a particular PC by entering either a full URL address or just a keyword of the Web site. URL/keyword : Add Reset Current URL Blocking Table: NO. URL/keyword Select Online Selected Delete All Reset Apply Cancel This

Enable URL Blocking Enable/disable URL Blocking

Add URL Keyword Fill in "URL/Keyword" and then click "Add". You can enter the full URL address or the keyword of the web site you want to block.

Remove URL Keyword If you want to remove some URL keywords from the "Current URL Blocking Table", select the URL keyword you want to remove in the table and then click "Delete Selected". If you want remove all URL keywords from the table, just click "Delete All" button. If you want to clear the selection and re-select again, just click "Reset".

Click at the bottom of the screen to save the above configurations

13 Advanced Settings

Network Address Translation (NAT) allows multiple users at your local site to access the Internet through a single Public IP Address or multiple Public IP Addresses. NAT provides Firewall protection from hacker attacks and has the flexibility to allow you to map Private IP Addresses to Public IP Addresses for key services such as Websites and FTP. Select Disable to disable the NAT function.

Virtual Server

Use the Virtual Server function when you want different servers/clients in your LAN to handle different service/Internet application type (e.g. Email, FTP, Web server etc.) from the Internet. Computers use numbers called port numbers to recognize a particular service/Internet application type. The Virtual Server allows you to re-direct a particular service port number (from the Internet/WAN Port) to a particular LAN private IP address and its service port number.

Sitecom wireless broadband router Wt. 341 - Mozilla Firefox Gealand, Beigden, Send, Gezeichnet, Modulators, Echo Help Meet beazche, Aon de slag, Laktote neaus, Grois Hotwar, Koppelingen ampasses, Windows Media, Windows 300N ROUTER SITECOM WIRELESS Status Wizard Wireless Settings Firewall Advanced Settings Toolbox Choose your language NAS Enable Virt. Serv. Spec. App. DPMP Qns Building SWIP You can configure the router as a Virtual Server allowing remote users to access services such as Web or FTP at your local PC. Depending on the requested server (TCP/UDP) port number, the router will redirect the external service request to the appropriate internal server (located at one of your local PCs). Current Virtual Server Table: NO. Local IP Local Port Type Public Port Enable 1 TCP 2 TCP 3 TCP 4 TCP 5 TCP 6 TCP 7 TCP 8 TCP 9 TCP 10 TCP Add Clean Add Clean Add Clean Add Clean Add Clean Add Clean Add Clean http://192.168.0/index.htm

Local IP This is the LAN client/host IP address that the Public Port number packet will be sent to.

Local Port This is the port number (of the above Private IP host) that the below Public Port number will be changed to when the packet enters your LAN (to the LAN Server/Client IP)

Type Select the port number protocol type (TCP, UDP or both). If you are unsure, then leave it to the default "both" setting. Public Port Enter the service (service/Internet application) port number from the Internet that will be re-directed to the above Private IP address host in your LAN Comment The description of this setting.

Enable Enable Virtual Server.

Add Virtual Server Fill in the "Local IP", "Local Port", "Type", "Public Port" and "Comment" of the setting to be added and then click "Add". Then this Virtual Server setting will be added into the "Current Virtual Server Table" below.

Remove Virtual Server If you want to remove Virtual Server settings from the "Current Virtual Server Table", select the Virtual Server settings you want to remove in the table and then click "Delete Selected". If you want to remove all Virtual Server settings from the table, just click the "Delete All" button. Click "Reset" will clear your current selections.

Click at the bottom of the screen to save the above configurations.

Special Applications

Some applications require multiple connections, such as Internet games, video Conferencing, Internet telephony and others. In this section you can configure the router to support multiple connections for these types of applications.

Sitecom wireless broadband router Wl. 341 - Mozilla Firefox Gealand, Regenien, Reid, Geschendek, Sodgubers, Ebro, Help http://192.168.0/index.htm 300N ROUTER WIRELESS SITECOM Status: Wizard Wireless Settings: Firewall Advanced Settings Toolbox Choose your language HAT Enable VIE Show Spec. App. UHP Qns Raising SHIP Some applications require multiple connections, such as Internet gaming, video conferencing, Internet telephony and others. These applications cannot work when network address Translation (NAT) is enabled. If you need to run applications that require multiple connections, specify the port normally associated with an application in the 'Trigger Port' field, select the protocol type as TCP or UDP, then enter the public ports associated with the trigger port to open them for inbound traffic. Trigger port Trigger type Public Port Public type Enabled 1. TCP ○ UDP 2. TCP ○ UDP 3. TCP ○ UDP 4. TCP ○ UDP 5. TCP ○ UDP 6. TCP ○ UDP 7. TCP ○ UDP 8. TCP ○ UDP 9. TCP ○ UDP 10. TCP ○ UDP http://192.168.0/index.htm

Trigger Port This is the out going (Outbound) range of port numbers for this particular application.

Trigger Type Select whether the outbound port protocol is "TCP", "UDP" or both.

Public Port Enter the In-coming (Inbound) port or port range for this type of application (e.g. 2300-2400, 47624)

Public Type Select the Inbound port protocol type: "TCP", "UDP" or both

Enable Trigger Port Enable the Special Application function.

Popular applications This section lists the more popular applications that require multiple connections. Select an application from the Popular

Applications selection. Once you have selected an application, select a location (1-10) in the Copy to selection box and then click the Copy to button. This will automatically list the Public Ports required for this popular application in the location (1-10) you specified.

UPNP

With UPnP, all PCs in you Intranet will discover this router automatically. So, you don't have to configure your PC and it can easily access the Internet through this router.

Sitecom wireless broadband router Wl. 341 - Mozilla Firefox Global Germany Sweden Switzerland Singapore Egypt Help Hindu besanche Aon da slag Laddate news Global News Kappelingen ampowers Windows Media Windows 300N ROUTER SITECOM WIRELESS Status Wizard Wireless Settings Break all Advanced Settings Toolbar Choose your language NAF Enable Vire Sare Sport App UPnP Open Running NVP Universal Plug and Play is designed to support zero-configuration, "Invisible" networking, and automatic discovery for a range of devices from a wide range of vendors. With UPnP, a device can dynamically join a network, obtain an IP address and learn about the presence and capabilities of other devices all automatically. Devices can subsequently communicate with each other directly. UPnP: Enable Disable Apply Cancel http://192.168.0.jholzqnp.stm

UPnP You can enable or Disable the UPnP feature here. After you enable the UPnP feature, all client systems that support UPnP, like Windows XP, can discover this router automatically and access the Internet through this router without having to configure anything. The NAT Traversal function provided by UPnP can let applications that support UPnP connect to the internet without having to configure the virtual server sections.

QoS

QoS can let you classify Internet application traffic by source/destination IP address and port number. You can assign priority for each type of application and reserve bandwidth for it. The packets of applications with higher priority will always go first. Lower priority applications will get bandwidth after higher priority applications get enough bandwidth. This can let you have a better experience in using critical real time services like Internet phone, video conference ...etc. All the applications not specified by you are classified as rule name "Others". The rule with a smaller priority number has a higher priority; the rule with a larger priority number has a lower priority. You can adjust the priority of the rules by moving them up or down.

Sitecom wireless broadband router Wl. 341 - Mozilla Firefox Bestand Regehen Reel Geosiedras Hydopters Ebro Help https://192.168.0/index.htm Market benchmark Aon de slag Lusible new user Grotis hirtow Koppelingen ampasses Windows Media Windows 300N ROUTER WIRELESS Status Wizard Wireless Settings Firewall Advanced Settings Toolbox Choose your language HAT Enable VAC New Spec App QMP QoS Raising SWP Quality of service (QoS) refers to the capability of a network to provide better service to selected network traffic. The primary goal of QoS is to provide priority including dedicated bandwidth, controlled jitter and latency (required by some real-time and interactive traffic), and improved loss characteristics, also important is making sure that providing priority for one or more flows does not make other flows fail. • WAV Out Bandwidth : 1000 kbps Enable or Disable QoS module function Enable Disable Diffserv Forwarding Groups: Below shows the Diffserv forwarding behaviors this router supports, User can further configure the bandwidth allocation of each forwarding behavior. Name Description Priority Bandwidth Allocation Minimum Allow More BE best Effort forwarding Lowest 0 kbps AF1x Assured Forwarding, provides delivery of packets in four independently forwarded air classes, Within each AF class, an IP packet can be assigned one of three different levels of drop recurrence High 0 kbps AF2x 0 kbps AF3x 0 kbps AF4x 0 kbps

Enable/Disable QoS You can check "Enable QoS" to enable QoS functionality for the WAN port.

Traffic mapping Click "Add traffic class" then enter a form of the QoS rule. Click "Apply" after filling out the form the rule will be added into the table.

Edit a QoS rule Select the rule you want to edit and click "Edit", then enter the detail form of the QoS rule. Click "Apply" after editing the form and the rule will be saved.

Adjust QoS rule priority. You can select the rule and click "Move Up" to make its priority higher. You also can select the rule and click "Move Down" to make its priority lower.

Routing

These screens define routing related parameters, including static routes and RIP (Routing Information Protocol) parameters.

Sitecom wireless broadband router WL-341 - Mozilla Firefox Gazand Recognien Email Geschadena Sluplatens Echo Help http://162.168.0.1/index.htm 300N ROUTER WIRELESS SITECOM Status Wizard Wireless Settings Firewall Advanced Settings Toolbox Choose your language NAV Enable Web, Spore Spore, App HTTP Quick Routing STOP List Routing Table: Flogs Network Address Netmask Gateway Interface Metric C 192.160.0.0 255.255.255.0 Traffic Mapping LAN --- C 197.0.0.1 255.255.255.255 Traffic Mapping Loopback --- Flags: C - directly connected, G - static, R - POP, I - ICMP Redirect: Static Route RIP

Routing Table Flags indicates the route status:

C = Direct connection on the same subnet.

S = Static route.

R = RIP (Routing Information Protocol) assigned route.

I = ICMP (Internet Control Message Protocol) Redirect route.

Static Route Click Add to add a new static route to the list, or check the box of an already entered route and click Modify. Clicking Delete will remove an entry from the list.

RIP RIP mode globally enables or disables RIP.

Auto summary If Auto summary is disabled, then RIP packets will include sub-network information from all sub-networks connected to the router. If enabled, this sub-network information will be summarized to one piece of information covering all sub-networks.

Table of current Interface RIP parameter

Interface The WAN interface to be configured.

Operation Mode Disable: RIP disabled on this interface.

Enable: RIP enabled on this interface.

Silent: Listens for route broadcasts and updates its route table. It does not participate in sending route broadcasts.

Version Sets the RIP (Routing Information Protocol) version to use on this interface.

SNMP

Use the SNMP configuration screen to display and modify parameters for the Simple Network Management Protocol (SNMP).

Sitecom wireless broadband router Wt. 341 - Mozilla Firefox Bestand Regenham Seed Geosynchronous Reduppliers Echo Help http://162.168.0.1/index.htm 300N ROUTER SITECOM WIRELESS Status Wizard Wireless Settings Firewall Advanced Settings Toolbox Choose your language Note Enable Virt Save Open App DRWR Init Sharing SNMP The Simple Network Management Protocol (SNMP) is an application layer protocol that facilitates the exchange of management information between network devices. It is part of the Transmission Control Protocol/Internet Protocol (TCP/IP) protocol suite. SNMP enables network administrators to manage network performances, find and solve network problems, and plan for network growth. The Device provides SNMP setting for community and trap information. Please select one of the SNMP Operation Modes for this device. SNMP Operation Mode: Dicedled Community Irop Apply Cancel http://162.168.0.1/jemp.htm

SNMP operation mode to select the SNMP modes for this device.

Community A computer attached to the network, called a Network Management Station (NMS), can be used to access this information. Access rights to the agent are controlled by community strings. To communicate with the Router, the NMS must first submit a valid community string for authentication. Note: Up to five community names may be entered.

Note: Up to five community names may be entered.

Trap Specify the IP address of the NMS to notify when a significant event is detected by the agent. When a trap condition occurs, the SNMP agent sends an SNMP trap message to any NMS specified as a trap receiver.

IP Address Traps are sent to this address when errors or specific events occur on the network. Community A community string (password) specified for trap management. Enter a word, something other than public or private, to prevent unauthorized individuals from accessing information on your system. Version Sets the trap status to disabled, or enabled with V1 or V2c. The v2c protocol was proposed in late 1995 and includes enhancements to v1 that are universally accepted.

These include a get-bulk command to reduce network management traffic when retrieving a sequence of MIB variables, and a more elaborate set of error codes for improved reporting to A Network Management Station.

14 TOOLBOX Settings

Password change options

You can change the password required to log into the broadband router's system web-based management. By default, the password is: admin.

Passwords can contain 0 to 12 alphanumeric characters, and are case sensitive.

Current Password Fill in the current password to allow changing to a new password.

New Password Enter your new password

Confirmed Password Enter your new password again for verification purposes

Click at the bottom of the screen to save the above configurations

Sitecom wireless broadband router WL-341 - Mozilla Firefox Gealand Regelum Field Gezeichnet Modulators Extra Help http://152.168.0.1/index.sta Prest besweite Aon de slag Loebie nauws Goia Hotswi Koppelingen anpasses Windows Media Windows 300N ROUTER SITECOM WIRELESS Status Wizard Wireless Settings Firewall Advanced Settings Toadbox Choose your language Password Timeless Remote Furniture Back-up Reset Buy You can change the password which is required to log on to the muter by default, the password is admin. Passwords can contain 0 to 30 alphanumeric characters, and are case sensitive. Current Password : New Password : Confirm Password : Apply Cancel Floor

Time Zone

The Time Zone allows your router to base its time on the settings configured here, which will affect functions such as Log entries and Firewall settings.

Sitecom wireless broadband router WL-341 - Mozilla Firefox Gzeland, Begeheim, Nord, Geschendria, Skobljens, Echo, Help http://192.168.0/index.htm Miret besanche: Aon de slog, Laikite nuneus, Global network, Koppelingen anpassers, Windows Media, Windows 300N ROUTER WIRELESS SITECOM Status Wizard Wireless Settings Firewall Advanced Settings Toolbox Choose your language Password Timeszone Secure Firmware Backup Reset Print Set the time zone of the broadband router, This information is used for log entries and firewall settings. Set Time Zone : (GMT+0) 30Amsterdam, Berlin, Bern, Rome, Stockholm, Vienna Time Server Address : 132.163.4.102 Daylight Saving : Enable From January To July Apply Cancel http://192.168.0/systemzone.htm

Set Time Zone Select the time zone of the country you are currently in. The router will set its time based on your selection.

Time Server Address You can set an NTP server address.

Enable Daylight Savings The router can also take Daylight savings into account. If you wish to use this function, you must check/tick the enable box to enable your daylight saving configuration (below).

Start Daylight Savings Time Select the period in which you wish to start daylight Savings Time.

End Daylight Savings Time Select the period in which you wish to end daylight Savings Time.

Click at the bottom of the screen to save the above configurations.

Remote Management

The remote management function allows you to designate a host in the Internet the ability to configure the Broadband router from a remote site. Enter the designated host IP Address in the Host IP Address field.

Sitecom wireless broadband router WL-341 - Mozilla Firefox Enland, Regenlan, Brand, Geoschendra, Modulators, Echo Help http://162.168.0.1/index.htm Metal bestache Aon de slag Lockgate remote Global Hotspot Koppeljogem appossens Windows Media Windows 300N ROUTER SITECOM WIRELESS Status Wizard Wireless Settings Firewall Advanced Settings Toolless Choose your language Password Timezone Remote Firmware Backup Reset Options The remote management function allows you to designate a host from the Internet to have management/configuration access to the router from a remote site. Enter the designated host IP Address in the Host IP Address field. Host Addresses Port Enable 1995 2000 Apply Cancel Http://[e-mail]

Host Address This is the IP address of the host in the Internet that will have management/configuration access to the Broadband router from a remote site. If the Host Address is left 0.0.0.0 this means anyone can access the router's web-based configuration from a remote location, providing they know the password.

Port The port number of the remote management web interface.

Enable Select "Enable" to enable the remote management function.

Click at the bottom of the screen to save the above configurations.

Firmware Upgrade

This page allows you to upgrade the router's firmware.

300N ROUTER WIRELESS SITECOM Status Wizard Wireless Settings Firewall Advanced Settings Toolbox Choose your language Password Telephone Remote Firmware Back-up Reset DNS This tool allows you to upgrade the Routers firmware. Browse to and select the upgrade file and click APPLY. You will be prompted to confirm the upgrade. Blodener.. Apply Cancel http://192.168.0.1/#/pagegrade.stm

Firmware Upgrade This tool allows you to upgrade the Broadband router's system firmware. To upgrade the firmware of your Broadband router, you need to download the firmware file to your local hard disk, and enter that file name and path in the appropriate field on this page. You can also use the Browse button to find the firmware file on your PC.

Once you've selected the new firmware file, click at the bottom of the screen to start the upgrade process

Backup Settings

The Backup screen allows you to save (Backup) the router's current configuration settings. When you save the configuration setting (Backup) you can re-load the saved configuration into the router through the Restore selection. If extreme problems occur you can use the Restore to Factory Defaults selection, this will set all configurations to its original default settings (e.g. when you first purchased the router).

Sitecom wireless broadband router WL-341 - Mozilla Firefox Bealand Regelien Bend Gezeichnet Modulators Extra Help http://152.168.0.1/index.htm 300N ROUTER SITECOM WIRELESS Status Wizard Wireless Settings Firewall Advanced Settings Toolbox Choose your language Password Sound Name Security Furniture Back-up Reset DOCS Use BACKUP to save the routers current configuration to a file named configuin. You can use RESTORE TO restore the saved configuration. Alternatively, you can use RESTORE TO FACTORY DEFAULT TO force the router to restore the factory default settings. Restore To Factory Default : Reset Backup Settings : Save Restore Settings : Bladeren... Uploaded http://152.168.0.1/nom.stm

Use the "Backup" tool to save the Broadband router current configuration to a file named "config.bin" on your PC. You can then use the "Restore" tool to restore the saved configuration to the Broadband router. Alternatively, you can use the "Restore to Factory Defaults" tool to force the Broadband router to perform a power reset and restore the original factory settings.

Reset

You can reset the router's system should any problem exist. The reset function essentially re-boots your router's system.

Sitecom wireless broadband router WL 341 - Mozilla Firefox Risland Recognien Reed Geschiedrak Skylabors Echo Help http://152.168.0.1/index.htm 300N ROUTER WIRELESS SITECOM Status Wizard Wireless Settings Firewall Advanced Settings Toolbox Choose your language Password Timestamp Remote Furniture Back up Reset DOK+S In the event the system steps responding correctly or stops functioning, you can perform a reset. Your settings will not be changed. To perform the reset, click on the APPLY button. You will be asked to confirm your decision. The reset will be completed when the LED Power light stops blinding. Apply Cancel http://152.168.0.1/reset.htm

DDNS

DDNS allows you to map the static domain name to a dynamic IP address. You must get an account, password and your static domain name from the DDNS service providers. This router supports DynDNS, TZO and other common DDNS service providers.

Sitecom wireless broadband router WL-341 - Mozilla Firefox Gealand Bergen Bend Geschindenk Magallers Egrs Help http://192.168.0.1/index.htm 300N ROUTER WIRELESS SITECOM status Wizard Wireless Settings Firewall Advanced Settings Toothes Choose your language Password Temporary Remote Firmware Backup Reset DONS DDNS allows users to map a static domain name to a dynamic IP address. You must get an account, password and your static domain name from the DDNS service provider. The router has DDNS support for www.cyndins.org and www.d20.com. Dynamic DNS : Enable Disable Provider : D:\DNET Domain Name : Account/E-mail : Password/Key : Apply Cancel http://192.168.0.1/wendins.com

Enable/Disable Enable/Disable the DDNS function of this router

Provider Select a DDNS service provider

Domain name Fill in your static domain name that uses DDNS

Account/E-mail The account that your DDNS service provider assigned to you

Password/Key The password you set for the DDNS service account above

Click at the bottom of the screen to save the above configurations.