VLPT-42H100 - Gps VigilLink - Free user manual and instructions

USER MANUAL VLPT-42H100 VigilLink

4x2 HDMI/USB-C 4K 18Gbps

Multi-format Collaboration

Switcher with HDBaseT 3.0

100m Out

Exterior view of a black electronic device with ports and control buttons, shown alongside an inset image of its external network interface (no readable text or symbols on the device itself)

User Manual

VER 1.0

Thank you for purchasing this product

For optimum performance and safety, please read these instructions carefully before connecting, operating or adjusting this product. Please keep this manual for future reference.

Surge protection device recommended

This product contains sensitive electrical components that may be damaged by electrical spikes, surges, electric shock, lighting strikes, etc. Use of surge protection systems is highly recommended in order to protect and extend the life of your equipment.

Caution

The product requires the use of UTP connectors. Please connect in direct interconnection method and do not cross connect.

1 2 3 4 5 6 7 8 T568B 1 2 3 4 5 6 7 8 T568B White and Orange Orange White and Green Blue White and Blue Green White and Brown Brown

Direct Interconnection Method

Table of Contents

1. Introduction...... 1
2. Features.... 1
3. Package Contents.... 1
4. Specifications.... 2
5. Operation Controls and Functions.... 3

5.1 Switcher Panel.... 3

5.2 HDBaseT Remote Panel.... 5
5.3 IR Cable Pin Assignment....7
6. IR Remote....7
7. Web GUI User Guide......8
8. RS-232 Control Command....15
9. Connection Diagram....23

1. Introduction

This 4x2 Collaboration Switch features 3 HDMI inputs, 1 USB-C input, 1 HDMI output and 1 HDBT collaboration output. It supports video up to 4K/60 4:4:4 with HDCP 2.3 and features HDBaseT 3.0 extension for uncompressed 4K video, embedded audio, control and USB over distances up to 330 feet (100 meters). USB-C input supports DP Alt mode for A/V, USB 2.0, 100M Ethernet and 60W charging for source device. All inputs and the local HDMI output support 4K HDR and 4K/60 4:4:4 at HDMI data rates up to 18 Gbps. Additionally, 4K to 1080p downscaling is available for the HDMI and HDBaseT outputs when connected to an HD sink. The integrated USB extension addresses the challenge of connecting between USB devices at remote locations and is ideal for software video conferencing and touch or interactive displays.

This Collaboration Switch includes USB 2.0 and USB-C interfaces for four host PCs, plus three peripheral devices such as a camera, microphone, speakerphone, or keyboard and mouse. The receiver also supports local HDMI and USB inputs for BYOD or PC devices. Host and RX both support audio de-embedded to analog balanced or un-balanced output.

2. Features

☆ 4x2 Collaboration Switch with HDMI/HDBT 3.0 330ft(100m) extension
☆ HDMI 2.0b, HDCP 2.3, 18Gbps
☆ HDBaseT 3.0 4K@60Hz up to 330ft(100m)
☆ Supports HDR, HDR10+, Dolby Vision LLM, HLG
☆ Host: 1x USB-C, 3x HDMI inputs, 3x USB 2.0 hosts and 3x USB 2.0 devices
Remote: 1x HDBT, 1x HDMI input, 1x USB 2.0 hosts and 2x USB 2.0 clients
☆ USB-C supports ALT-DP mode for A/V, USB 2.0 data, and power charging up to 60 watts
☆ 4K to 1080p downscaling features on all HDMI outputs, no frame rate conversion
☆ Host/Remote both support analog audio de-embedding
☆ CEC and RS-232 external display control on both host and remote
☆ EDID management
Host supports POE/PSE, Remote supports POE/PD (Remote doesn't have an external DC power supply)
☆ The front panel button, RS-232, and TCP/IP control (Host TCP/IP port for API and Web GUI)
☆ The host half rack size for easy installation

3. Package Contents

① 1 x 4x2 Collaboration Switch
② 1 x HDBaseT Recmote Device
③ 1 x IR Blaster Cable (1.5 meters)
④ 1 x IR Wideband Receiver Cable (1.5 meters)
⑤ 2 x 3pin-3.5mm Phoenix Connector (male)
⑥ 2 x 5pin-3.5mm Phoenix Connector (male)
⑦ 4 x Mounting Ear
⑧ 8 x Machine Screw
⑨ 1 x 24V/6A Desktop Power Supply & 1 x AC Power Cord (1.5 meters)
⑩ 1 x IR Remote
⑪ 1 x User Manual

4. Specifications

Technical
HDMI Compliance HDMI	2.0b
HDCP Compliance HDCP	2.2
DP Version DP 1.2
Video Bandwidth 18Gbps
Video Resolution	Up to 4K@60Hz 4:4:4
IR Level 12Vp-p
IR Frequency Wideband	20K-60KHz
Color Space	Input: 8/10/12-bit, 8-bit (4K60Hz 4:4:4)
Color Depth RGB, YCbCr	4:4:4 / 4:2:2, YUV 4:2:0
Audio Formats	USB-C/HDMI/HDBT:LPCM, Dolby Digital/Plus/EX, Dolby True HD, Dolby Atmos, DTS, DTS-EX, DTS-96/24, DTS High Res, DTS-HD Master Audio, DSDAUDIO OUT [Analog audio, balanced 2CH (Max output level 2Vrms) & unbalanced 2CH (Max output level 1Vrms)]
Transmission Distance	4K60 -- 328ft/100m
HDR	HDR, HDR10, HDR10+, Dolby Vision, HLG
ESD Protection	Human-body Model:±8kV (Air-gap discharge), ±4kV (Contact discharge)
Connection
Host	Input: 3 x HDMI INPUT [Type A, 19-pin female]1 x USB-C [24-pin female]Output: 1 x HDMI OUTPUT [Type A, 19-pin female]1 x HDBT OUTPUT [RJ45]1 x AUDIO OUTPUT [5pin-3.81mm phoenix connector]Control: 1 x RS-232 [3pin-3.81mm phoenix connector]1 x TCP/IP [RJ45]3 x USB HOST [USB Type B]3 x USB DEVICES [USB Type A]1 x IR IN [3.5mm stereo mini-jack]1 x IR OUT [3.5mm stereo mini-jack]
Remote	Input: 1 x HDMI IN [Type A, 19-pin female]1 x HDBaseT IN [RJ45]Output: 1 x HDMI OUT [Type A, 19-pin female]1 x LINE OUT [5pin-3.81mm phoenix connector]Control: 1 x RS-232 [3pin-3.81mm phoenix connector]1 x USB HOST [USB Type B]2 x USB DEVICES [USB Type A]1 x SERVICE [Micro USB]1 x IR IN [3.5mm stereo mini-jack]1 x IR OUT [3.5mm stereo mini-jack]
Mechanical
Housing Front panel: Aluminum; Rear case: Metal Enclosure
Color	Black
Dimensions	Host: 220mm [W]×150mm [D]×44mm [H]Remote: 140mm [W]×105mm [D]×21.5mm [H]
Weight	Host: 1.16Kg; Remote: 424g
Power Supply	Input: AC100 - 240V 50/60HzOutput: DC 24V/6A (US/EU standard, CE/FCC/UL certified)
Power Consumption	100W (Max)
Operating Temperature	0°C ~ 40°C / 32°F ~ 104°F
Storage Temperature	-20°C ~ 60°C / -4°F ~ 140°F
Relative Humidity 20%~90% RH (non-condensation

5. Operation Controls and Functions

5.1 Switcher Panel

Front Panel

4x2 MULTI-FORMAT Collaboration Switch HDMI 1 HDMI 2 HDMI 3 USB-C 4 HDMI 1 HDMI 2 HDMI 3 USB-C 4 POWER HDMI OUT HDBT OUT 1 2 ● ●

No.	Name Function Description
1 IR	Window	IR signal receiving window, receiving the IR remote signal.
2No.	HDMI OUT button & HDMI 1 / HDMI 2 / HDMI 3 / USB-C 4 LEDsName Function Description	Press the HDMI OUT button to circularly select the HDMI 1 / HDMI 2 / HDMI 3 / USB-C 4 port as the signal input channel for HDMI output, the corresponding LED will be on. The button light will automatically turn off after 1 second each time.
3	HDBT OUT button & HDMI 1 / HDMI 2 / HDMI 3 / USB-C 4 LEDs	Press the HDBT OUT button to circularly select the HDMI 1 / HDMI 2 / HDMI 3 / USB-C 4 port as the signal input channel for HDBT output, the corresponding LED will be on. The button light will automatically turn off after 1 second each time.
4	POWER button	Press and hold this button for 3 seconds, the product will enter standby mode and the button light will be on. In standby mode, short press this button, the product will be turned on and the button light will be off.

Rear Panel

1 2 3 4 5 HOST 1 HOST 2 HOST 3 USB 3USB 2USB 1 HDMI 1HDMI HDMI 3HDMI 2 INPUTSOUTPUTS USB-C 4 60W IR OUTIR IN TX + RX DC 24V RS-232 TCP/IP 6 8 9 10 11 12 13

No.	Name Function Description
1	USB 1/2/3 port	Three USB extension ports, connected to mouse, keyboard, USB camera or other USB devices.
2	HOST 1/2/3 port	Three USB Host ports, connected to PC.
3	IR IN port	Connect the IR receiver cable, used for IR signal pass-through or controlling this product via the IR remote.
4	IR OUT port	Connect the IR blaster cable, the IR signal is from the IR IN port of the HDBaseT Receiver.
5	DC 24V port	Power port, connected to the DC 24V power adapter.
6	AUDIO OUTPUT port	Analog audio output port, supporting balanced audio input (with a maximum support of 2Vrms) and unbalanced audio input (with a maximum support of 1Vrms).Balanced connection method: L+, L-, ±, R+, R-Unbalanced connection method: L+, ±, R+Note: This port is used to output the de-embedding audio from the HDBT OUTPUT port, and it supports volume adjustment through Web GUI or API command.
7	HDBT OUTPUT port	HDBaseT output port, connected to the HDBaseT IN port of the receiver with a CAT6A (F/FTP) cable.
8	Data Signal Indicator (Yellow)	Light on: HDMI signal input with HDCP.Light flashing: HDMI signal input without HDCP.Light off: No HDMI signal input.
No.	Name 4	Function Description
9	Link Signal Indicator (Green)	·Light on: Transmitter and Receiver are in good connection status.·Light flashing: Transmitter and Receiver are in poor connection status.·Light off: Transmitter and Receiver are not connected.
10	HDMI OUTPUT port	HDMI signal output port, connected to HDMI display device such as TV or monitor with HDMI cable.
11	HDMI 1/2/3 INPUT ports	HDMI signal input ports, connected to HDMI source device such as DVD or Blu-ray player with HDMI cable.
12	USB-C 4 port	USB-C signal input port, connected to USB-C signal source device, with the function of 60W charging.
13	RS-232 port	RS-232 serial port, used for RS-232 signal pass-through or controlling this product via RS-232 commands.
14	TCP/IP port	Connect to a router or Switch for USB-C Internet access or Web GUI control.

5.2 HDBaseT Remote Panel

LINK VIDEO HDBT HDMI 1 2 SELECT IR IN IR OUT DEVICES SERVICE 1 3 4 5 8 9 10 HDBaseT IN: HDMI IN HOST HDMI OUT LINE OUT TX RX RS-232 DC 24V 12 11 13 14 15 16 17 19

No.	Name 4	Function Description
1	Power LED	When the receiver is powered on, the red power LED will be on.
2	LINK LED	• Light on: Transmitter and Receiver are in good connection status.• Light flashing: Transmitter and Receiver are in poor connection status.• Light off: Transmitter and Receiver are not connected.
3	VIDEO LED	• Light on: HDMI signal input with HDCP.• Light flashing: HDMI signal input without HDCP.• Light off: No HDMI signal input.
4	HDBT LED	When the HDBaseT IN port is selected as the signal input channel, the green HDBT LED will be on.
No.	Name Function Description
5	HDMI LED	When the HDMI IN port is selected as the signal input channel, the green HDMI LED will be on.
6	SELECT button	Press this button to select signal input channel.
7	IR IN port	Connect the IR receiver cable, the IR signal will be sent to the IR OUT port of the transmitter.
8	IR OUT port	Connect the IR blaster cable, the IR signal is from the IR IN port of the transmitter.
9	DEVICES ports	Two USB extension ports, connected to whiteboard, mouse, keyboard, USB camera or other USB devices.
10	SERVICE port	Firmware update port.
11	HDBaseT IN port	HDBaseT input port, connected to the HDBT OUTPUT port of the transmitter with a CAT6A (F/FTP) cable.
12	Data Signal Indicator (Yellow)	Light on: HDMI signal input with HDCP.Light flashing: HDMI signal input without HDCP.Light off: No HDMI signal input.
13	Link Signal Indicator (Green)	Light on: Transmitter and Receiver are in good connection status.Light flashing: Transmitter and Receiver are in poor connection status.Light off: Transmitter and Receiver are not connected.
14	HDMI IN port	HDMI signal input port, connected to HDMI source device such as DVD or Blu-ray player with HDMI cable.
15	HOST port	USB Host port, connected to PC.
16	HDMI OUT port	HDMI signal output port, connected to HDMI display device such as TV or monitor with HDMI cable.
17	LINE OUT port	Analog audio output port, supporting balanced audio output (with a maximum support of 2Vrms) and unbalanced audio output (with a maximum support of 1Vrms).Balanced connection method: L+, L-,±, R+, R-Unbalanced connection method: L+,±, R+
18	RS-232 port	RS-232 serial port, used for RS-232 signal pass-through or controlling this receiver via RS-232 commands.
19	DC 24V port	Power port, connected to the DC 24V power adapter.Note:The receiver also can be powered by PoE (through the HDBaseT IN port).

5.3 IR Cable Pin Assignment

The pin assignment of the IR Receiver cable and IR Blaster cable is as below:

IR RECEIVERIR BLASTER IR BLASTER 1 + 2 - 1 IR Signal 2 Grounding 3 Power 12V

Note: When the angle between the IR receiver and the remote control is ±45^ , the transmission distance is 0-5 meters; when the angle between the IR receiver and the remote control is ±90^ , the transmission distance is 0-8 meters.

6. IR Remote

1 HDMI OUT USB-C 4H 4KHDAL 2 HDBT OUT USB-C 4H 4KHDAL 3 Collaboration Switch Remote

① Power buttonPress this button to power on the switcher or set it to standby mode.
② HDMI OUT control:

HDMI 1 / HDMI 2 / HDMI 3 / USB-C 4: Press these buttons to select input source for HDMI output, and the corresponding input LED on the front panel will be on.

◀▶: Press these buttons to circularly select the last or next input source for HDMI output.

AUTO: Press this button to enable/disable the auto switching function.

'4K/HD: Press this button to set the output scaling mode (Auto/Bypass/Force 1080p)

③ HDBT OUT control:

HDMI 1 / HDMI 2 / HDMI 3 / USB-C 4: Press these buttons to select input source for HDBT output, and the corresponding input LED on the front panel will be on.

◀▶: Press these buttons to circularly select the last or next input source for HDBT output.

AUTO: Press this button to enable/disable the auto switching function.

4K/HD: Press this button to set the output scaling mode (Auto/Bypass/Force 1080p)

7. Web GUI User Guide

The Collaboration Switch can be controlled by Web GUI. The operation method is shown as below:

Step 1: Get the current IP Address.

The default IP address is 192.168.0.100 (when the system is not connected to a router). You can get the current Collaboration IP address via RS-232 command control. Send the ASCII command "r ip addr" through a Serial Command tool, then you'll get the current IP address (The IP address is variable, depending on what the specific machine returns).

For the details of RS-232 control, please refer to "8. RS-232 Control Command".

Step 2: Connect the TCP/IP port of the Collaboration Switch to a PC with an UTP cable (as shown in the following figure), and set the IP address of the PC to be in the same network segment with the Collaboration Switch.

Diagram showing a router connected to a laptop via a blue cable labeled 'PC' (no text or symbols on the diagram itself)

Step 3: Input the current IP address of Collaboration Switch into your browser on the PC to enter Web GUI interface.

← → C Q http://192.168.0.100

After entering the Web GUI page, there will be a Login interface, as shown below:

User Password Login

The default usernames and passwords are as below:

Username	User	Admin
Password	1234	1234

Select the username "User" and input the password "1234", then click the "Login" button to enter the User page.

■ User Page

4x2 MULTI-FORMAT MATRIX SWITCHER User | Power On | Logout Control Preset Video Preset 1 Preset 2 Preset 3 Preset 4 Preset 5 Video Input HDMI 1 HDMI 2 HDMI 3 USB-C 4 Off HDMI OUT HDBT Out All outputs Audio Line Out 3 25 50 75 100 19

You can do the following operations on the User page:

① Preset: Recall the preset application scenes. (Note: The preset name only displays 8 characters.)
② Video: Select the input source for output to set the video switching.
③ Audio: Set the audio volume or mute/unmute the audio for Line Out, which is the de-embedding audio from HDBT output.

In the Login interface, select the username "Admin" and input the password "1234", then click the "Login" button to enter the Information page of the Admin interface.

■ Information Page

4x2 MULTI-FORMAT MATRIX SWITCHER Admin Power On Logout Information Model Name VLPT-42H100 MCU Version 1.0.0 Web Version 2.0.3 CFLD Version 1.0.4 RX Version 1.0.4 MAC Address 6G.DF.FB.07:12:15 IP Address 192.188.102.1T3 Subnet Mask 255.255.255.0 Gateway 192.188.102.1 Control Preset Input Output USB RS-232 Network System

The Information page provides basic information about the model name, software version and the network settings of the device.

Besides, you can do the following operations on each page of the Admin interface.

① Display the current username (User or Admin).
② Click the power icon to power on the swithcher or set it in standby mode.
③ Click the logout icon to logout and return to the login interface.

■ Control Page

4x2 MULTI-FORMAT MATRIX SWITCHER Admin Standby Logout Information Control Video Input RCKU XIAOMI APPLE TV MacBook Auto Off LG SONY AI outputs RS: 232 Network System Audio Line Out 0 25 50 75 100 50

You can do the following operations on the User page:

① Video: Select the input source for output to set the video Collaboration Switching. Note: The name of the input source/output device can be modified in the Input/Output page.

② Audio: Set the audio volume or mute/unmute the audio for TX Line Out, which is the de-embedding audio from HDBT output.

■ Preset Page

4x2 MULTI-FORMAT MATRIX SWITCHER Preset Preset ID Preset Name Preset Save Preset Clear Preset Recall 1 Preset 1 Save Clear Recal 2 Preset 2 Save Clear Recal 3 Preset 3 Save Clear Recal 4 Preset 4 Save Clear Recal 5 Preset 5 Save Clear Recal System

You can set up to 5 preset scenes on the Preset page.

① Preset Name: You can name the preset scene with a maximum of 16 characters.
(Chinese name is not supported.)
② Preset Save: Click the Save button to save the scene.
③ Preset Clear: Click the Clear button to clear the saved scene.
④ Preset Recall: Click the Recall button to recall the saved scene.

■ Input Page

4x2 MULTI-FORMAT MATRIX SWITCHER Admin Standby Logout Information Control Preset Input Output USB RS-232 Network System Input Input Name Cable EDD Harp HDMI 1 HDMI 1 Connected Auto On HDMI 2 HDMI 2 Connected Auto On HDMI 3 HDMI 3 Connected Auto On USB-C 4 USB-C 4 Connected Auto On EDD Load Download EDD Form HDMI 1 Download User Defined 1 EDD Load EDD No file chosen Save EDD User Defined 2 EDD Load EDD No file chosen Save EDD

You can do the following operations on the Input page.

Input Setting

① Name: The name of the input port. You can name it with a maximum of 8 characters.
② Cable: It indicates the connection status of the input port.
③ EDID: Click the drop-down list to set EDID for each input port. The EDID list is as below.

No.	EDID Mode	No.	EDID Mode
1	Auto	9	1680x1050, Stereo Audio 2.0
2	Copy HDMI OUT	10	1600x1200, Stereo Audio 2.0
3	Copy HDBT OUT	11	1440x900, Stereo Audio 2.0
4	4K2K60_444, Stereo Audio 2.0	12	1360x768, Stereo Audio 2.0
5	4K2K30_444, Stereo Audio 2.0	13	1280x1024, Stereo Audio 2.0
6	1080P, Stereo Audio 2.0	14	1024x768, Stereo Audio 2.0
7	720P, Stereo Audio 2.0	15	User Defined 1
8	1920x1200, Stereo Audio 2.0	16	User Defined 2

④ hdcp: Click the drop-down list to set HDCP.

EDID Load

① Click the drop-down list to select HDMI 1\HDMI 2\HDMI 3\USB-C 4\HDMI OUT\HDBT OUT for EDID download.
② Click the Download button to download EDID and generate a .bin file.
③ Click the Load EDID button to download user-defined EDID. Please note that only. bin files are supported.
④ Click the Save EDID button to save the user-defined EDID.

■ Output Page

4x2 MULTI-FORMAT MATRIX SWITCHER Admin Standby Logout Information Control Preset Input Output Output Name Cable Signal Scaling HDCP On/Off HDMI OUT LG Connected 3840x2180p60Hz YUV 4:2:0 8bit Auto Auto On HDBT OUT SONY Connected 3840x2180p30Hz YUV 4:4:4 8bit Auto Auto On USB RS-232 Network System

You can do the following operations on the Output page:

① Name: The name of the output port. You can name it with a maximum of 8 characters.
② Cable: It indicates the connection status of the output port.
③ Signal: The video information of the output signal.
④ Scaling: Set the video output mode (Auto/Bypass/Force 1080p).
⑤ HDCP: Set the HDCP output (Auto/HDCP1.4/HDCP2.2).
⑥ On/Off: Turn on/off the video output.

■ USB Page

4x2 MULTI-FORMAT MATRIX SWITCHER Information Control Preset Input Output USB USB Host Switch Mode Follow Video USB-C 4 Manual Switch HOST 1 Auto Switch USB-C 4 Save USB RS-232 Network System

USB Host Switch Mode

① Follow Video: Click this button to set the USB transmission follow the video switch (follow the HDBT output).
② Manual Switch: Switch to HOST 1\HOST 2\HOST 3\USB-C 4 manually.
③ Auto Switch: Detect and switch to HOST 1\HOST 2\HOST 3\USB-C 4 automatically. After setting up, click "Save" to take effect.

■ RS-232 Page

RS-232 RS-232 Settings Local RS-232 HDBT RS-232 Baud Rate 115200 Data Bit 8 Bit Parity None Stop Bit 1 Bit Save Baud Rate 115200 Data Bit 8 Bit Parity None Stop Bit 1 Bit Save

RS-232 Commands (Display Auto Power) Local RX-232 Commands Display On Command Delay 1 Display Input Select Delay 2 Remote RS-232 Commands Display On Command Delay 1 Display Input Select Delay 2 HEX ON Display Off Command Delay HEX Display Off Command Delay HEX Save

RS-232 Settings

① Local RS-232: You can set the Baud Rate, Data Bit, Parity and Stop Bit for the RS-232 port of the transmitter.
② HDBT(Remote) RS-232: You can set the Baud Rate, Data Bit, Parity and Stop Bit for the RS-232 port of the receiver.

RS-232 Commands (Display Auto Power)

① Local/Remote RS-232 Commands: You can turn on/off the local/remote RS-232 commands and hex.
② Display On/Off Command: You can input the display on/off command of the device.
③ Delay 1: You can set the delay time for the next action (such as send the Display Input Select command).
④ Display Input Select: You can input the command of switching the input channel for the display device.
⑤ Delay 2: You can set the delay time for the next action after sending the Display Input Select command.
After setting up, click "Save" to take effect.

■ Network Page

4x2 MULTI-FORMAT MATRIX SWITCHER Network Network Configuration IP Mode DHCP Data IP Address TPE WENDS15 Subnet Mask CNT-095-095-095 Cathway TCE-WNDS15 Tether Port 23 Domain Name VLPT-42H100-1215 Local Cancel SAVE Information Control Preset Input Output USB RS-232 Network System

Network Configuration: You can set the IP Mode (DHCP/Static), IP Address, Subnet Mask. Gateway, Telnet Port and Domain Name.

Note: The Domain Name "VLPT-42H100-1215.local" can be used to login the Web GUI. After setting up, click "Save" to take effect. Or you can click "Cancel" to cancel the setting.

■ System Page

4x2 MULTI-FORMAT MATRIX SWITCHER Admin Standby Logout Information Control Preset Import Output USB RS-232 Network System System Account Passwords User Ctrl Password... New Password... Confirm Password... Save Admin Ctrl Password... New Password... Confirm Password... Save Display Control CRC Command Power On Power Off Display Auto Power Auto Power Off Timer & sec Save Control Type RS-232 -Save System Utilities Front Panel Buttons ON Deep ON USB-C Ethernet Access ON Default Restore Factory Settings Export Settings Import Settings Firmware Update Choose File No file chosen Update %

Account Passwords: You can modify the login password for User and Admin. After setting up, click "Save" to take effect.

Display Control

① CEC Command: You can power on/off the CEC command.
② Display Auto Power: You can turn on/off the Display Auto Power. When it is set to ON, you can control the display device power on/off or switch the port based on the power status (power on/standby) or the signal input status of the transmitter by sending serial port or CEC Power On/Off command.

③ Auto Power off Timer: Click the drop-down list to select the delay time for sending the command to turn off the display device when the transmitter is in standby mode or there is no signal input.
④ Control Type: Click the drop-down list to select the control type.

System Utilities

① Front Panel Buttons: Click "ON/OFF" to lock/unlock panel buttons. "On" indicates that panel buttons are available; "OFF" indicates panel buttons are unavailable.
② Beep: Click "ON/OFF" to turn on/off the beep.
③ USB-C Ethernet Access: Click "ON/OFF" to turn on/off the Ethernet access function of USB-C.
④ Reboot: Click "Reboot" to reboot the switcher.
⑤ Restore Factory Settings: Click this button to restore the switcher to factory settings.
⑥ Export Settings: Click this button to export configuration files.
⑦ Import Settings: Click this button to import configuration files.

Firmware Update: You can update the software of MCU, Web, CPLD or receiver. Click "Choose File" to select the update file, then click "Update" to start update. When the progress bar reaches 100%, the update is complete.

8. RS-232 Control Command

The product also supports RS-232 command control. Connect the RS-232 port of the product to a PC with a 3-pin phoenix connector cable and an RS-232 to USB cable. The connection method is as follows.

TX + RX RS-232 TX Ground RX 3-pin Phoenix Connector RS-232 PC RS-232 to USB cable

Then open a Serial Command tool on PC to send ASCII commands to control the product. The ASCII command list about the product is shown as below.

ASCII Command
Serial port protocol: Baud rate: 115200 (default), Data bits: 8bit, Stop bits:1, Parity bit: noneTCP/IP protocol port: 8000
x - Parameter 1, y - Parameter 2
Command Code	Function Description FeedbackExample			Default Setting
System Setting
?	Get the list of all commands	?	====================VLPT-42H100 Help InfoMCU 1.1.0 Web 1.1.0FPGA 1.1.0 RX 1.1.0====================System Setting Command?Get the list of all commands helpGet the list of all commands r typeGet device model......====================	List all API commands.
help	Get the list of all commands	help	====================VLPT-D6 Help InfoMCU 1.1.0 Web 1.1.0FPGA 1.1.0 RX 1.1.0====================System C6 Command?Get the list of all commands helpGet the list of all commands r typeGet device model......====================	List all API commands.
r type Get device model		r type	VLPT-42H100
r status Get device current status		r status		List current status.Please see Status Feedback sheet
r fw version Get Firmware version		r fw version	MCU 1.1.0 Web 1.1.0FPGA 1.1.0 RX 1.1.0
s power on Power on the device		s power on	Power on System Initializing...Initialization Finished!MCU 1.1.0 Web 1.1.0FPGA 1.1.0 RX 1.1.0
s power off Power off the device		s power off	Power off
r power	Get current power state	r power	power on /power off
s reboot Reboot the device		s reboot	Reboot...System Initializing...Initialization Finished!MCU 1.1.0 Web 1.1.0FPGA 1.1.0 RX 1.1.0
s reset	Reset system settings to default (Should type "Yes" to confirm, "No" to discard)	s reset	Sure to Reset System Settings To Default? Type "Yes" after next prompt to confirm...
s reset all	Reset system and network settings to default (Should type "Yes" to confirm, "No" to discard)	s reset all	Sure to Reset System and Network Settings To Default? Type "Yes" after next prompt to confirm...
Command Code	Function Description Feed	backExample		Default Setting
s front button on/off	Set front button on/off	s front button on	Set front button on	on
r front button	Get front button on/off status	r front button	Front button on
s beep on/off	Set buzzer on/off	s beep on	Set beep on	off
r beep	Get buzzer on/off status	r beep	Beep on
s USBC access network on/off	Set USB-C access network feature on/off	s USBC access network on	Set USB-C access network feature on	on
r USBC access network	Get USB-C access network feature on/off status	r USBC access network	USB-C access network feature on
Input Setting
s input x EDID y	Set input EDID (x=0~4) (y=1~16)x=0: all inputsx=1: HDMI 1x=2: HDMI 2x=3: HDMI 3x=4: USB-C 4y=1: Auto (HDBT or HDMI or HDBT+HDMI)y=2: Copy HDMI OUTy=3: Copy HDBT OUTy=4: 4K2K60_444, Stereo Audio 2.0y=5: 4K2K30_444, Stereo Audio 2.0y=6: 1080P, Stereo Audio 2.0y=7: 720p, Stereo Audio 2.0y=8: 1920x1200, Stereo Audio 2.0y=9: 1680x1050, Stereo Audio 2.0y=10: 1600x1200, Stereo Audio 2.0y=11: 1440x900, Stereo Audio 2.0y=12: 1360x768, Stereo Audio 2.0y=13: 1280x1024, Stereo Audio 2.0y=14: 1024x768, Stereo Audio 2.0y=15: User Defined 1y=16: User Defined 2	s input 0 EDID 1	Set all input EDID: Auto	1
r input x EDID	Get input EDID mode (x=0~4)x=0: all inputsx=1: HDMI 1x=2: HDMI 2x=3: HDMI 3x=4: USB-C 4	r input 0 EDID	Input HDMI 1(Name)EDID: AutoInput HDMI 2(Name)EDID: AutoInput HDMI 3(Name)EDID: AutoInput USB-C 4(Name)EDID: Auto
r input x EdidData	Get input EDID Data (x=0~4)x=0: all inputsx=1: HDMI 1x=2: HDMI 2x=3: HDMI 3x=4: USB-C 4	r input 0 EdidData	Input HDMI 1(Name)EDID Data:<00 FF FF FF...>Input HDMI 2(Name)EDID Data:<00 FF FF FF...>Input HDMI 3(Name)EDID Data:<00 FF FF FF...>Input USB-C 4(Name)EDID Data:<00 FF FF FF...>
s input x HDCP on/off	Set input HDCP (x=0-4) on/offx=0: all inputsx=1: HDMI 1x=2: HDMI 2x=3: HDMI 3x=4: USB-C 4	s input 0 HDCP on	Set all input HDCP: On	on
r input x HDCP	Get input HDCP (x=0-4) on/off status	r input 0 HDCP	Input HDMI 1(Name)HDCP: OnInput HDMI 2(Name)HDCP: OnInput HDMI 3(Name)HDCP: OnInput USB-C 4(Name)HDCP: On
Output Setting
s output x from y	Set output (x=0-2) from input(y=0-4)x=0: all outputs (HDMI/HDBT),x=1: HDMI outputx=2: HDBT outputy=0: Offy=1: HDMI 1y=2: HDMI 2y=3: HDMI 3y=4: USB-C 4	s output 0 from 1	Set HDMI(Name) output from: HDMI 1(Name)Set HDBT(Name) output from: HDMI 1(Name)	1
r output x from	Get output (x=0-2) from which inputx=0: all outputs (HDMI/HDBT),x=1: HDMI outputx=2: HDBT output	r output 0 from	HDMI(Name) output from:HDMI 1(Name)HDBT(Name) output from:HDMI 1(Name)
s output x scaling y	Set output (x=0-2) scaling (y=1-3)x=0: all outputs (HDMI/HDBT)x=1: HDMI outputx=2: HDBT outputy=1: Autoy=2: Bypassy=3: Force 1080p	s output 0 scaling 1	Set HDMI(Name) output scaling: AutoSet HDBT(Name) output scaling: Auto	1
r output x scaling	Get output scaling status	r output 0 scaling	HDMI(Name) output scaling: AutoHDBT(Name) output scaling: Auto
s output x hdcp y	Set output (x=0~2) hdcp (x=1~3)x=0: all outputs (HDMI/HDBT)x=1: HDMI outputx=2: HDBT outputy=1: Autoy=2: HDCP 1.4y=3: HDCP 2.2	s output 0 hdcp 1	Set HDMI(Name) output HDCP: AutoSet HDBT(Name) output HDCP: Auto	1
r output x hdcp	Get output (x=0~2) hdcp statusx=0: all outputs (HDMI/HDBT)x=1: HDMI outputx=2: HDBT output	r output 0 hdcp	HDMI(Name) output HDCP: AutoHDBT(Name) output HDCP: Auto
s output x avmute on/off	Set output (x=0-2) avmute on/offx=0: all outputs (HDMI/HDBT),x=1: HDMI outputx=2: HDBT output	s output 0 avmute on	Set HDMI(Name) output AVMUTE: OnSet HDBT(Name) output AVMUTE: On	off
r output x avmute	Get output (x=0-2) avmute on/off status	r output 0 avmute	HDMI(Name) output AVMUTE: OnHDBT(Name) output AVMUTE: On
s output x auto switch mode y	Set output (x=0-2) auto switch detection mode (y=1-2)x=0: all outputs (HDMI/HDBT)x=1: HDMI outputx=2: HDBT outputy=1: TMDSy=2: 5V	s output 0 auto switch mode 1	Set HDMI(Name) output auto switch mode: TMDS	1
r output x auto switch mode	Get output (x=0-2) auto switch detection mode	r output 0 auto switch mode	HDMI(Name) output auto switch mode: TMDS
s output x auto switch on/off	Set output (x=0-2) auto switch on/offx=0: all outputs (HDMI/HDBT),x=1: HDMI output,x=2: HDBT output	s output 0 auto switch on	Set HDMI(Name) output auto switch: On	off
r output x auto switch	Get output (x=0-2) auto switch on/off status	r output 0 auto switch	HDMI(Name) output auto switch: On
Audio Setting
s output line vol y	Set output line volume to yy=[0-100] volume value	s output line vol 50	Set output line volume: 50	50
r output line vol	Get output line volume	r output line vol	Output line volume: 50
s output line vol+	Increase output line volume	s output line vol+	Increase output line volume: 52
s output line vol-	Decrease output line volume	s output line vol-	Decrease output line volume: 50
s output x mute on/off	Set output (x=null/line/HDMI/HDBT) mute on/off	s output mute on s output line mute on s output HDMI mute on s output HDBT mute on	Set output all mute: On Set output line mute: On Set output HDMI(Name) mute: On Set output HDBT(Name) mute: On0	off
r output x mute	Get output (x=null/line/HDMI/HDBT) mute on/off status	r output mute r output line mute r output HDMI mute r output HDBT mute	Output all mute: On Output line mute: On Output HDMI(Name) mute: On Output HDBT(Name) mute: On
RX Setting
s rx output from x	Set RX output from input (x=1-2)x=1:HDBT INx=2:HDMI IN	s rx output from 1	Set RX output from: HDBT IN Error, RX not ready!	1
r rx output from Get	RX output from which input	r rx output from	RX output from: HDBT IN
r rx hdmi5v Get RX	HDMI input power 5V	r rx hdmi5v	RX HDMI 5V: 1
r rx host5v Get RX U	USB host power 5V	r rx host5v	RX host 5V: 1
s rx auto switch mode x	Set RX auto switch detection mode (x=1~2)x=1: TMDSx=2: 5V	s rx auto switch mode 1	Set RX auto switch mode: TMDS	1
r rx auto switch mode	Get RX auto switch detection mode	r rx auto switch mode	RX auto switch mode: TMDS
s rx auto switch on/off	Set RX auto switch on/off	s rx auto switch on	Set RX auto switch: On	on
r rx auto switch	Get RX auto switch on/off status	r rx auto switch	RX auto switch: On
Command Code	Function Description Feedback	backExample		Default Setting
CEC Setting
s cec power on/off	Set CEC power on/off command	s cec power on s cec power off	Set CEC power on Set CEC power off
s auto power feature on/off	Set display auto power feature on/off	s auto power feature off	Set auto power feature: Off	off
r auto power feature	Get display auto power feature on/off status	r auto power feature	Auto power feature: Off
s auto power off timer x	Set auto power off command (CEC/RS-232) will be sent out after xx=1: 5sec, x=2: 10sec,x=3: 30sec, x=4: 1min,x=5: 5min, x=6: 10min	s auto power off timer 4	Set auto power off timer: 1min	4
r auto power off timer	Get auto power off timer	r auto power off timer	Auto power off timer: 1min
s auto power control x	Set auto power feature control via (x=1-3)x=1: CEC, x=2: RS-232,x=3: CEC and RS-232	s auto power control 1	Set auto power control: CEC	1
r auto power control	Get auto power feature control type	r auto power control	Auto power control: CEC
USB Setting
s USB switch mode x	Set USB switch mode (x=1-3)x=1: Follow video (HDMI 1/Host 1, HDMI 2/Host 2,HDMI 3/Host 3, USB-C 4)x=2: Manual modex=3: Auto mode (detect host 5V then switch)	s USB switch mode 1	Set USB switch mode: Follow video	1
r USB switch mode	Get USB switch mode	r USB switch mode	USB switch mode: Follow video
s USB from x	Set USB manual switch from input (x=0-4)x=0: None, x=1: Host 1,x=2: Host 2, x=3: Host 3,x=4: USB-C 4	s USB from 1	Set USB from: Host 1	1
r USB from	Get USB manual switch from which input	r USB from	USB from: Host 1
RS-232 Setting
s serial x setting y	Set serial port (x=0-2) setting to yx=0: All RS-232 (Local and HDBT)x=1: Local RS-232x=2: HDBT RS-232y= 115200-8n1	s serial 0 setting 115200-8n1	Set all RS-232: 115200-8n1	115200-8n1
r serial x setting	Get serial port (x=0-2) settingx=0: All RS-232 (Local and HDBT)x=1: Local RS-232x=2: HDBT RS-232	r serial 0 setting	All RS-232: 115200-8n1
Preset Setting
s preset save x	Save the current unit's settings to the specified preset:xAll settings except network setting.x=[1-5]: Preset 1 - Preset 5	s preset save 1	Save to preset 1
s preset recall x	Recall a specified preset:x into unitAll settings except network setting.x=[1-5]: Preset 1 - Preset 5	s preset recall 1	Recall preset 1
Command Code	Function Description Feed	backExample		Default Setting
s preset clear x	Clear a specified preset:xAll settings except network setting.x=[1-5]: Preset 1 - Preset 5	s preset clear 1	Clear preset 1
s preset x name y	Set preset:x name to yx=[1-5]: Preset 1 - Preset 5y: Preset name, max 16 characters	s preset 1 nameMeetingRoom 1	Set preset 1 name:MeetingRoom 1
r preset x name	Get preset:x namex=[1-5]: Preset 1 - Preset 5	r preset 1 name	Preset 1 name:MeetingRoom 1
Network Setting
r ipconfig	Get the Current IP Configuration	r ipconfig	IP Mode:DHCPIP Address:192.168.0.100Subnet Mask:255.255.0.0Gateway:192.168.0.1TCP/IP port:8000MAC:6C:DF:FB:0C:B3:8E
r mac addr	Get network MAC address	r mac addr	MAC: 6C:DF:FB:0C:B3:8E
s ip mode x	Set network IP mode tox=0: Static,x=1: DHCP	s ip mode 0	Set IP mode: Static(Please use "s net reboot" command or repower device to apply new config!)	1
r ip mode	Get network IP mode	r ip mode	IP mode: Static
s ip addr xxx.xxx.xxx.xxx	Set network IP address	s ip addr192.168.1.100	Set IP address:192.168.0.100(Please use "s net reboot" command or repower device to apply new config!)DHCP on, Device can't config static address,set DHCP off first.
r ip addr	Get network IP address	r ip addr	IP: 192.168.0.100
s subnetxxx.xxx.xxx.xxx	Set network subnet mask	s subnet255.255.255.0	Set Subnet Mask:255.255.255.0(Please use "s net reboot!" command or repower device to apply new config!)DHCP on, Device can't config subnet mask, set DHCP off first.
r subnet	Get network subnet mask	r subnet	Subnet Mask:255.255.255.0
s gatewayxxx.xxx.xxx.xxx	Set network gateway	s gateway192.168.1.1	Set Gateway: 192.168.1.1(Please use "s net reboot!" command or repower device to apply new config!)DHCP on, Device can't config gateway, set DHCP off first.
r gateway	Get network gateway	r gateway	Gateway: 192.168.1.1
s tcp/ip port x	Set network TCP/IP port(x=1~65535)	s tcp/ip port 8000	Set TCP/IP port: 8000	8000
r tcp/ip port	Get network TCP/IP port	r tcp/ip port	TCP/IP port: 8000
Command Code	Function Description FeedbackExample			Default Setting
s telnet port x	Set network telnet port (x=1~65535)	s telnet port 23	Set Telnet port: 23	23
r telnet port	Get network telnet port	r telnet port	Telnet port: 23
s net reboot	Reboot network modules	s net reboot	Searching IP, please wait ...IP Mode: DHCPIP Address:192.168.0.100Subnet Mask:255.255.0.0Gateway: 192.168.0.1TCP/IP port: 8000MAC:6C:DF:FB:0C:B3:8E
Password Setting
s admin password x	Set admin login password (x=[16 characters max])	s admin password 1234	admin password: 1234	1234
r admin password	Get admin login password	r admin password	admin password: 1234
s user password x	Set user login password (x=[16 characters max])	s user password 1234	user password: 1234	1234
r user password	Get user login password	r user password	user password: 1234

Note: The feedback of the command of "r status" is as following.

VLPT-42H100 Status