107-HO1 - Kit voiture Metra - Free user manual and instructions

USER MANUAL 107-HO1 Metra

Interior view of a car dashboard with a mounted digital display showing the screen and air vent (no visible text or symbols)

Honda Civic 2022-2024

Visit MetraOnline.com for more detailed information about the product and up-to-date vehicle specific applications

KIT FEATURES

Designed specifically for Pioneer modular 6.8" radios like the DMH-C2550NEX and DMH-WC5700NEX.

^†† Refer to the radio manufacturer for current models
- Requires the Pioneer extension cable (sold separately)
- Textured and painted to match the factory finish.

KIT COMPONENTS

• A) Radio display front panel - B) Radio display back panel - C) - Radio chassis brackets - D) Radio display brackets
  • E) #8 x 3/8" Phillips screws (8) • F) #4 x 3/8" Phillips screws (2)

A

Simple line drawing of a rectangular frame with a recessed inner rectangle (no text or symbols)

• 

Technical line drawing of a rectangular electronic enclosure or panel with mounting holes and internal compartments (no text or symbols)

• 

• 

• 

F

TABLE OF CONTENTS

Dash Disassembly....2

Kit Assembly 3

WIRING & ANTENNA CONNECTIONS (sold separately)

Visit metraonline.com for audio/video and steering wheel control interface options.

Wire harness: AXTC-HN1

Antenna adapter: 40-HD11

TOOLS REQUIRED

- Panel removal tool • Phillips screwdriver

Attention! With the key out of the ignition, disconnect the negative battery terminal before installing this product. Ensure that all installation connections are secure before cycling the ignition to test this product.

DASH DISASSEMBLY

1. Unclip and remove the trim panel below the radio screen that includes the A/C control and A/C vents. (Figure A)
2. Unclip and remove the trim panel from the top of the dash behind the radio screen. (Figure B)

Line drawing of a car interior showing dashboard, steering wheel, and air vent (no text or symbols)

(Figure A) (Figure C)

1. Remove (2) Phillips screws under trim panel on top of dash behind radio screen. (Figure C)
2. Remove (2) Philips screws securing the radio and screen then unclip and remove the assembly from the dash. (Figure D)

Continue to Kit Assembly

Technical line drawing of a mechanical assembly with arrows indicating force or movement (no text or symbols)

Technical line drawing of a vehicle's front suspension system with arrows indicating movement (no text or symbols)

Diagram of a car interior showing a gray plastic seat and directional arrow (no text or symbols)

(Figure B) (Figure D)

KITASSEMBLY

1. Place the three factory panel clips onto the bottom of the radio display back panel
   Note: For steps 2 and 3, reference the installation manual provided with the radio for which hardware to use. The display screen and radio chassis use two different types of screws.
2. Secure the radio chassis brackets to the radio chassis using (6) screws supplied with the radio. (4 on top one each side) (Figure A)
3. Secure the radio display brackets to the radio display using (4) screws supplied with the radio. (Figure B)
4. Route cable from chassis through radio display back panel and plug into to radio display.
5. Secure radio display assembly to the radio display back panel using (4) of the supplied #8 screws. (Figure C)

Technical line drawing of an electronic device casing with mounting holes and wiring (no text or symbols)

(Figure A)

Technical diagram showing two mechanical components with alignment guides and a black arrow indicating a transformation or assembly (no text or symbols present)

(Figure B)

1. Secure the radio chassis to the back of the radio display front panel using (4) of the supplied #8 screws. (Figure D)
2. Clip the bottom of the radio display front panel to the radio display back panel and secure using (2) of the supplied #4 x 3/8" Phillips screws. (Figure E)
3. Locate the factory wiring harness and antenna connector in the dash and complete all necessary connections to the radio. Metra recommends using the proper mating adapter from Metra and/or Axxess. Test the radio for proper operation.
4. Clip the radio assembly into to the dash, then secure using the factory screws.
5. Reassemble the dash in reverse order of disassembly to complete the installation.

Technical diagram of a mechanical assembly with no visible text or symbols

(Figure C)

Technical line drawing of a mechanical assembly with mounting brackets and housing (no text or symbols)

(Figure D)

Technical illustration of a device casing with internal components and an arrow indicating direction (no text or symbols present)

(Figure E)

Having difficulties? We're here to help.

Contact our Tech Support line at:

386-257-1187

Or via email at:

[e-mail]

Tech Support Hours (Eastern Standard Time)

Monday - Friday: 9:00 AM - 7:00 PM

Saturday: 10:00 AM - 5:00 PM

Sunday: 10:00 AM - 4:00 PM

Metra recommends MECP certified technicians