CPD1200EILCD - Inverter CyberPower - Free user manual and instructions

USER MANUAL CPD1200EILCD CyberPower

1 IMPORTANT SAFETY INSTRUCTIONS......4

2 INSTALLATION....5

2-1 Unpacking....5
2-2 Product Overview & Outlook....5
2-3 Power Requirements of Your Equipment....7
2-4 Hardware Installation Guide....7

3 DEFINITIONS FOR ILLUMINATED LCD INDICATORS......9

Power On/Off....11
Function Setup....11
Audible Alarm....11
Function Setup Guide....11

5 TROUBLESHOOTING....14

6 TECHNICAL SPECIFICATIONS....16

1 IMPORTANT SAFETY INSTRUCTIONS

(SAVE THESE INSTRUCTIONS)

Before attempting to unpack, install, or operate the product, please read and follow all instructions carefully.

CAUTION! To prevent the risk of fire or electric shock, install in a temperature and humidity controlled indoor area free of conductive contaminants. (Please see Technical Specifications section for acceptable temperature and humidity range.)

CAUTION! The product must be installed in a protected environment away from heat-emitting appliances such as a radiator or heat register. The location should provide adequate air flow around the product for proper ventilation.

CAUTION! To reduce the risk of injury, use cables come with the product. Use appropriate and certified external battery cables.

CAUTION! To reduce risk of damage and injury, use batteries with good quality.

CAUTION! Risk of electric shock. DO NOT remove the cover. No user serviceable parts inside.

CAUTION! Provide adequate ventilation for the battery compartment. The battery enclosure should be designed to prevent accumulation and concentration of hydrogen gas at the top of the compartment.

CAUTION! A battery can present a risk of electrical shock and high short circuit current. When working on batteries, remove watches, rings, or other metal objects. Use tools with insulated handles.

CAUTION! Hazardous live parts inside can be energized by the battery even when the AC input power is disconnected.

CAUTION! To avoid electrical shock, turn off the unit and unplug it from the AC power source before installing equipment or servicing the battery. Servicing the battery can only be performed by trained personnel.

DO NOT USE FOR MEDICAL OR LIFE SUPPORT EQUIPMENT! Do not use in any circumstance that would affect the operation and safety of life support equipment, medical applications, or patient care.

DO NOT USE WITH OR NEAR AQUARIUMS! To reduce the risk of fire or electric shock, do not use with or near an aquarium. Condensation from the aquarium can cause the unit to short out.

DO NOT USE THE PRODUCT ON ANY TRANSPORTATION! To reduce the risk of fire or electric shock, do not use the unit on any transportation such as airplanes or ships. The effect of shock or vibration caused during transit and the damp environment can cause the unit to short out.

2 INSTALLATION

2-1 Unpacking

Inspect the product upon receipt. The box should contain the following:

(a) This product; (b) User Manual; (c) Input Power Cord

3D geometric diagram of a hexagonal prism with internal grid pattern (no text or symbols)

Power inverter

Simple line drawing of an open book with blank pages (no text or symbols)

User Manual

Pure diagram of a twisted rope or cable with no text, numbers, or symbols

Input Power Cord

2-2 Product Overview & Outlook

CyberPower Power Inverter ensures home/office users the always-on power supply with the exceptional power performance. Featuring the high-efficiency conversion design, the Power Inverter supplies long-lasting and reliable power to various appliances and provide longer backup for equipment. These units can be installed in either a horizontal or wall-mounted placement to make the most of your space.

CPD1200EILCD

CyberPower ① ② ③

Diagram of a device rear panel with labeled components including fan, socket, and indicator lights

1. Multifunction LCD Readout
2. Power On/off Switch
3. Function Buttons
4. AC Inlet
5. DC Input Cable(Red "+")
6. DC Input Cable(Black "-"')
7. AC Outlet

Application Diagram

graph TD
    A["Light / Lamp"] --> B["Desktop PC"]
    B --> C["CyberPower Power Inverter with external battery pack"]
    D["Standing Fan"] --> C
    E["TV"] --> C

2-3 Power Requirements of Your Equipment

1. Ensure that the equipment plugged into the AC outlet does not exceed the product's rated capacity (1200VA/900W for CPD1200EILCD). If rated unit capacities are exceeded, an overload condition may occur and cause the unit to shut down or the circuit breaker trip.

2. There are many factors that can affect the amount of power that your appliances will require. For optimal system performance keep the load below 80% of the unit's rated capacity.

2-4 Hardware Installation Guide

Step 1 Connect the Battery

For optimal battery life and reasonable recharging time, make sure the batteries capacity no less than 100Ah. Use batteries with same brand, type, and capacity.

Connect DC input cables of this product to external batteries:

Red “+” cable to the battery's Positive “+” polarity

Black “-” cable to the battery’s Negative “-” polarity

Single Battery Connection

Single battery voltage must be equal to DC voltage of the unit.

DC Breaker

Multiple Batteries Connection – in Series

Connect two batteries in series can double the voltage. Sum of voltages must be equal to DC voltage of the unit.

Diagram showing two square boxes connected by a curved line to a 3D octagonal panel with internal grid pattern (no text or symbols)

Multiple Batteries Connection – in Parallel

Connect multiple batteries in parallel can increase total battery capacity but still keep terminal voltage as single battery voltage.

Technical line drawing of a door frame with four square components and a diagonal hatching pattern (no text or symbols)

Step 2 Connect the Product to Utility

Connect the product to a wall outlet. Charging the battery for at least 8 hours is recommended to ensure that the battery's maximum charge capacity is achieved. To recharge the battery and maintain optimal battery charge, simply leave the unit plugged into a wall outlet at all times. The battery can be charged whether the unit is turned on or off.

DO NOT connect Neutral of the Power Distribution Box to (a) the OUTPUT Neutral of this product, or (b) the INPUT Neutral of connected equipment. Otherwise, reversed polarity will damage the product and connected equipment.

graph TD
    A["Utility power"] --> B["L"]
    A --> C["N"]
    A --> D["G"]
    B --> E["Inverter"]
    C --> E
    D --> E
    E --> F["Load"]
    G["Common Neutral"] --> E
    H["X"] --> I["Ground"]

Step 4 Connect the Load

Connect the load to the unit's outlet. Make sure that the total loads of your appliances are below 80% of the unit's rated capacity.

3 DEFINITIONS FOR ILLUMINATED LCD INDICATORS

LCD Display

I/P O/P PV BATT. KVA MkWh Default Min A Hz % K$ °C

The left half of the LCD screen displays the energy flow direction and the status of the Power Inverter. The right half of the LCD screen displays the input, output, and battery information.

Icon	Description
	Normal Mode (Power On)The Power Inverter is turned on.
	Standby Mode (Power Off)The Power Inverter is off while the LCD display remains on.
	Utility PowerUtility power source supplies AC power.
	Load CapacityThe approximate load capacity of the unit's outlet. (in 25% increments)
	Battery CapacityThe approximate battery capacity and charging status. (in 25% increments)
	FaultThis icon appears if there is a problem with the unit.
	OverloadThis icon appears and an alarm sounds to indicate the outlet is overloaded.MuteThis icon appears whenever the unit is in silent mode. However, when there is a problem with the unit, the alarm will still beep even in silent mode.
	Setup ModeThis icon appears whenever the unit is in Setup Mode.
I/P O/P PV BATT.	Input / Output / Battery InformationIt indicates input, output, and battery information.

Operation Modes

There are three types of modes regarding to the operation of the Power Inverter. The corresponding LCD displays are as shown below.

LCD Display	Operation Mode
	Standby ModeIn Standby Mode, the Power Inverter is off and the Utility power bypasses to output and in the meantime charges the battery. The LCD is on to show battery status.
	Line ModeThe Power Inverter is turned on and AC input power is normal. It supplies power to the load (connected equipment).
	Battery ModeDuring a severe brownout or blackout, the Utility Power is absent and the Power Inverter switches to Battery Mode. The battery will supply power to the load (connected equipment).

Power On: Press the POWER button to turn on the unit.

Power Off: Press the POWER button again to turn off the unit.

Setup Power Select

Function Setup

Press the SETUP button for 4 seconds to access the setup mode's 9 functions: Audible Alarm, Input Voltage Range, Utility Charging Current, Auto Restart Voltage, Low Battery Shutdown Voltage, LCD Auto Sleep, Cycling Display, Back to Default, and Return to Status Display. Short press the SELECT button to view the functions. When a function is selected, short press the SETUP button to access the function's options. Short press SELECT button to view the options. When the desired option is selected, short press SETUP button to confirm the setting. The unit will leave Setup Mode if there is no operation in 60 seconds.

Audible Alarm

Press SELECT button for 2 seconds to enable the audible alarm (beeps once) or disable (beeps twice) the audible alarm. The MUTE icon will appear on the LCD display when the audible alarm is disabled.

Function Setup Guide

Function	Options	Default	Description
Page 1 - Audible Alarm	OnOffESC	On	If Off is selected, the unit will mute alarms and the Mute icon will appear on the LCD display.
Page 2 – Input Voltage Range	Hi (Wide):(90-280Vac)Lo (Narrow):(170-280Vac)ESC	Hi	For connected equipment that are less sensitive to the fluctuation of voltage range, set the input voltage range wider and the output voltage will follow.For connected equipment that are sensitive to the fluctuation of voltage range, narrow the input voltagerange.Note: The transfer time will increase while the input voltage gets lower. If the connected equipment is sensitive to the transfer time, power interruption condition may occur.
Page 3 – Utility Charging Current	10/15/20AESC	20A	With different battery capacity, adjust utility charging current to provide optimal recharging time.Recommended setting:10A for 100Ah battery15A for 150Ah battery20A for 200Ah battery
Page 4 – Auto Restart Voltage	Any/10.5/11.0//11.5/12.0/12.5/13.0/FULESC	Any	When the utility power comes back and starts to charge the battery, the Power Inverter will auto restart at the setting battery voltage.
Page 5 – Low Battery Shutdown Voltage	10.0/10.2/10.4/10.6/10.8/11.0VESC	10.0V	The Power Inverter will shut off if the battery voltage is decreasing to the setting value.
Page 6 – LCD Auto Sleep	Off0.5/1/2 MinESC	1 Min	If Auto Sleep is selected, the LCD display will shut off after 0.5/1/2 minutes if no activity.
Page 7 – Cycling Display	Off0.5/1 MinESC	0.5 Min	If the buttons are not touched in 0.5/1 minute, the LCD will start cycling the Inverter information.
Page 8 – Back to Default	ESCYes	ESC	Select Yes to restore the factory default settings.
Page 9 – Return to Status Display	-	-	Press the Setup button to go back to the status display.

5 TROUBLESHOOTING

Problem	Possible Cause	Solution
The product will not turn on.	The unit is not connected to an AC wall outlet.	The unit must be connected to a 220/230V outlet.
	The battery is worn out.	Replace the batteries.
	Mechanical problem.	Contact CyberPower Systems.
Outlet does not provide power to connected equipment.	Circuit breaker has tripped due to an overload.	Turn the unit off and remove some of the connected equipment. Wait 10 seconds, reset the circuit breaker by depressing the button, and then turn the unit on.
	DC fuse is blown due to overload.	Servicing of the DC fuse should only be performed by trained personnel. For more information on DC fuse replacement, contact CyberPower Systems.
	Batteries are discharged.	Recharge the unit for at least 8 hours.
	The product may require service.	Contact CyberPower Systems.
There is no LCD display.	The product is not turned on.	Press the power button.
	Batteries are discharged.	Recharge the unit for at least 8 hours.
	The LCD is defective.	Contact CyberPower Systems.
Utility power is normal but the unit is in Battery Mode.	AC input is missing.	Make sure the AC input is well-connected.
	Input protector is tripped.	Reset the input protector.
The audible alarm beeps continuously.	The unit is in Fault Mode.	Refer to Fault Code Table for further information. Contact CyberPower Systems.

Fault Code Table

Fault Code	Event	Audible Alarm
A64	Overload	Rapid beeping every 1/2 second
E07	Output Voltage High	Constant tone
E09	Output Short	Constant tone
E14	Overload Fault	Constant tone
E18	Fan Fail	Constant tone
E13	Over Charge	Constant tone
E25	Output Voltage Unbalance	Constant tone

6 TECHNICAL SPECIFICATIONS

Model	CPD1200EILCD
Power Rating (VA/Watt)	1200VA/900W
Input
Input Voltage Range	Narrow Mode: 170 - 280VacWide Mode: 90 - 280Vac
Input Frequency	50/60Hz (Auto-sensing)
Output
Output Voltage	230Vac
Output Frequency	50/60Hz
Outlet Type	(1) UN
Transfer Time	< 8ms (Typical Narrow Mode)
Battery
Battery Voltage	12V
Charging Current	10A / 15A / 20A (Adjustable)
Environmental
Operating Temperature (°C)	0°C to 40°C
Operating Relative Humidity	0 to 90% (non-condensing)
Physical
Dimensions (WxHxD) (mm.)	266 x 92 x 273
Weight (kg.)	2.5

For more information, visit www.cyberpower.com

All rights reserved. Reproduction without permission is prohibited.

CyberPower®