DynamoPower VX54 - Vacuum Cleaner VAX - Free user manual and instructions

USER MANUAL DynamoPower VX54 VAX

DYNAMIC POWERFUL PERFORMANCE, FOR TOTAL HOME CLEANING

Close-up of a green and gray vacuum cleaner with 'MAX' branding, shown against an orange background (no text on device body)

LET'S GET STARTED.

2 YEAR WARRANTY

Let's talk safety

Basic safety precautions	This vacuum cleaner is intended for household use only and NOT for commercial or industrial use.READ ALL THE INSTRUCTIONS BEFORE USING THIS APPLIANCEOnly use the vacuum cleaner indoors and keep the area you're cleaning well lit.Keep fingers, hair and loose clothing from moving parts and openings whilst using the vacuum cleaner.This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities or lack of experience and knowledge unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.	Children should not play with the vacuum cleaner. Cleaning and user maintenance should not be made by children without supervisionOnly Vax recommend tools and accessories should be used with this vacuum cleanerVax recommends the use of a Residual Current Device rating of 30 mA or less.If the supply cord is damaged, it must be replaced by the manufacturer, or similarly qualified person in order to avoid a hazard, or invalidating the warranty.IMPORTANT:The motor is equipped with a thermal cut-out. If for any reason the unit should overheat, the thermostat will automatically turn the unit off. Should this occur, unplug the vacuum cleaner from the electrical outlet and turn off the switch. Remove dirt container and empty. Clean filters. Allow the unit to cool for approximately one (1) hour. To re-start, plug into an electrical outlet and switch back on.
Don'ts	Do not pull or carry by cord, use cord as a handle, close a door on cord, or pull cord around sharp edges or corners. Do not place product on cord. Do not run appliance on cord.Don't handle the plug or use the vacuum cleaner with wet hands.Don't use the vacuum cleaner with incorrect voltage as this may result in damage or injury to the user. The correct voltage is listed on the rating label.Don't vacuum up hot coals, cigarette butts, ash, matches or smoking hot burning items or use in an area where there may be harmful fluids (chlorine, bleach, and ammonia drain cleaner).	Don't attempt to remove blockages with sharp objects as this may cause damage to the vacuum cleaner.Do not vacuum hard or sharp objects such as glass, nails, screws or coins etc.Do not vacuum plaster dust, concrete dust or any other building or vitreous material.Do not vacuum flour, baking soda or any other powder-based carpet refresher or deodoriser.Don't use this vacuum cleaner if it has been dropped, damaged or left outdoors.Don't vacuum up any flammable or combustible materials (lighter fluid, petrol, kerosene etc.) or use the vacuum cleaner in an area with explosive vapours or liquid.
Do's	Always make sure the filter and dirt container are fitted correctly before using your vacuum cleaner.Turn off all controls on the vacuum cleaner before disconnecting or connecting the battery.Take extra care when cleaning on the stairs.Always switch off the vacuum cleaner before disconnecting or connecting the hose and accessories.Always protect the charger cord from heated surfaces or near open flames.	Use only SAA approved 10amp extension cords. Care should be taken to arrange the extension cord as it can be a trip hazard.Always carry the vacuum cleaner by the handle.Store your vacuum cleaner in a cool, dry area.Always keep the power cord away from the brushes whilst using your vacuum cleaner.PLEASE KEEP INSTRUCTIONS FOR FURTHER USE.

Thank you for buying this Dynamo Power Total Home.

Taking care of your carpets and hard floors

The Dynamo Power Total Home is designed to make vacuuming carpets and hard floors regularly, as effective and efficient as possible and this user guide will help you get the most out of your machine.

Maintaining your carpets and hard floors will ensure they keep their appearance for longer. You've chosen carpets and hard floors for your home for a reason and Vax will help you take good care of them.

Taking care of your Dynamo Power Total Home

Also inside this guide are instructions on maintaining your new machine, so that it's always ready when you are to tackle your carpets and hard floors.

We're here if you need us

For troubleshooting simply visit or call:

vax

Australia: 1300 361 505* New Zealand: 0800 800 900*

vax.com.au vax.co.nz

*Monday - Friday: 8:30am -5:00pm

Calls are charged at the standard local rate. Please make note of the serial number and model number of the product before calling.

Contents

Let's talk safety

Getting to know your machine

Getting started

Using your machine

Taking care of your machine

Let's talk technical

Accessories

Notes

What to do if it goes wrong

Getting in touch

Dynamo Power Total Home

Included with your machine

Combination Floorhead

Telescopic Extension Tube

3-in-1 Tool

Accessory Hose

Hardfloor Tool.

TurboTool

Turbo Brush

Up-lap Tool

Getting to know your machine

Getting started

Dirt bin lid release clip vax Separator and shroud Dirt container Hose entry point Carry handle Dirt container release button Power On/O4 button Cord rewind button Post-motor filter cover release clip Post motor filter cover

Technical Specification

Name Dynamo Power Total Home

Voltage: 220-240V-50Hz

Wotttec 1600w

Cord length 6m

Weight 5.2kg

Subject to technical change without notice.

Accessories & Consumables

Filter pack*

VX54F

*To purchase consumables and accessories, please visit vax.com.au

PLEASE READ 'LET'S TALK SAFETY' AT THE BEGINNING BEFORE USE

Before you begin cleaning

• Always switch off and unplug the vacuum cleaner before connecting or disconnecting the nose/attachments, or removing and emptying the dirt container.
• The vacuum cleaner is equipped with a thermal cut-out. It for any reason the vacuum cleaner does overheat the thermostal will automatically turn the vacuum cleaner off. If this happens, switch the vacuum cleaner off and unlock from electrical socket. Remove and empty the dirt container also check the vacuum cleaner for backages. Allow the vacuum cleaner to cool for approximately 1 hour (if you have cleaned the titers please wait 24 hours for the titers to fully dry before putting back into the vacuum machine).
• For best cleaning results, filters should be tapped over a bin every 4.6 uses to remove dirt and debris and washed every 3 to 6 months (depending on the level of use).
• If the vacuum cleaner is blocked, switch off and unplug before removing the blockage.

Assembling your vacuum cleaner

Press both buttons at the end of the hose and push hose into the hose entry point.

Insert the hose grip into the telescopic extension tube.

Press the button on the telescopic extension tube and adjust to required length.

Insert the other end of the telescopic extension tube into the floorhead.

Fully unwind the power cord. A yellow mark on the cord indicates the recommended cord length. Do not exceed the cord beyond the yellow mark.

Plug in and switch the unit on by pressing the power button.

When unwinding the power cord always pull out to the yellow marker but no further.

CAUTION

Using your machine

Using your machine

CAUTION: The base of the vacuum cleaner should always be positioned flat on the floor when starting and in use. The dirt container should be locked into place before lifting the vacuum cleaner by the carry handle.

How to use

For use on carpets, click rocker switch forward. For use on hard floors click rocker switch back.

Raise brushes for carpels.

Lower brushes for hard floors.

Slide vent cover on hose grip open to reduce suction if required.

For the most efficient results on hard floors replace the combination floorhead with the specialist hard floor too,

Using accessories

Illustration of a hand holding an orange tool, with other tools and components shown in separate views (no text or symbols present)

Choose an accessory. Choose an accessory and push onto the telescopic extension tube or hose.

Storage

Press the cord rewind button to retract the cord into the vacuum cleaner.

Place the floorhead into the parking slot on the back of the vacuum cleaner for storage and carrying.

CAUTION: Make sure to hold the cord with your other hand to prevent injury when rewinding.

Taking care of your machine

Taking care of your machine

IMPORTANT: Always switch off and unplug the vacuum cleaner from the electrical socket before assembling, opening or emptying the dirt container, or before connecting/disconnecting the attachments.

Pre-motor filter should be tapped over a pin every 4-6 uses to remove dirt and debris. Do not use your vacuum cleaner without all of the filters in place.

The inrotor is equipped with a thermal cut out, if for any reason the unit should overheat, the thermostal will automatically turn the unit off.

Emptying and cleaning the dirt container

Remove dirt container by pushing down the dirt container release button and lifting the dirt container.

Hold the dirt container over a bin. Push down the dirt release clip at the bottom of the dirt container. The dir. release door will open allowing dir/debr is to fall out.

Don't over fill the dirt container to avoid blocking the air flow through the vacuum clearer.

Cleaning the Pre-motor filter

CAUTION: Incorrect fitting of the separator cap will reduce suction.

Lift the dirt bin lid release clip. In a hinge like manner lift open the lift bin lid.

Pull the filter-tab and remove the pre-motor filter

Tap the filter over a bin to remove any dirt/debris. Wash the filter under running water (40 degrees max).

I leave for 24 hours or until fully dry before replacing.
Re? The pre-mic or filler into the dirt container with the tab being visible.
In a hinge like manner close the dirt bin lic until it clicks into place.

Post-motor filter maintenance

IMPORTANT: The post motor filter is designed to offer long life with no maintenance. The filter should be checked periodically and when heavily discoloured it should be replaced. Please do not wash, scrub or brush the filter as this will damage the filter

Push the post-motor filter cover release clip to the right to remove the post motor filter cover.

Full the post motor filter to the left and remove the post motor filter.

Check the post motor filter for discolouration. Do not wash the post motor filter.

Cleaning the separator, shroud and separator plate

After employing the diri container, vis. the separator clockwise to unlock and lift to remove.

Taking care of your machine Let's talk technical

Unscrew the shroud anti clockwise and remove.

Pull to remove the separator plate.

Tap the separator, shroud and separator plate over a bin to remove any dirt/debris. Using a dry coat wipe the remaining dirt/debris from the separator, shroud and separator plate.

Re-fitting the separator plate, shroud plate

Line up and push the separator plate into place.

Reft the shroud twisting clockwise to lock Into place.

Line up the separator making sure both rectangular holes in the dirt container and separator line up.

Twist the separator anti clockwise to lock into place.

Refit the dirt container pushing down firmly until it clicks and locks into place.

Removing blockages from the TurboTool

Side the locking ring to remove.

Lift and separate the housing.

Using a pair of scissors, cut any hair or debris free from around the brushes.

Line up the tabs on front of housing and push together to reft. Slide locking ring into groove to secure.

Removing blockages from the Turbobrush

Technical line drawing of a mechanical assembly with no visible text or symbols

Switch the vacuum cleaner off and disconnect the power plug from the electrical outlet.
Lay the Turbobrush on a flat surface and turn over to expose the brushbar. Using a pair of scissors, cut through any threads or hairs caught around the brushes and brushbar.

Removing blockages from the hose

Remove the hose from the vacuum cleaner and telescopic extension tube. Insert a broom handle or a similar bunt instrument into the hose to remove blockage.

To test for a blockage in the nose, drop a small ball of paper into the nose. The paper will drop through if the hose is clear.

Don't forget your accessories!

Order at: www.vax.com.au / www.vax.co.nz

Pro Cleaning Kit

Model no. VPCK

Crevice tool

For backward gaps and crevices.

Upholstery attachment

Gently cleans large areas of upholstery, curtains,

select end orders.

Pet hair removal attachment

Tackles stubborn pet hair on furniture, rugs and carpets.

Stubborn dust brush attachment

Removes built up dust from skinling, baris, and corners.

Radiator Tool

Long s m design, is perfect for cleaning behind

and inside the radiator

Up Top Tool

Ideal for reaching these hard to rescue

high areas.

Mattress Tool

Quickly and easily removes

embedded dust from motresses.

Soft Brush

Cently removes dust and dirt

from delicate surfaces such

as tiles and plases without

Scratching.

Filter Pack

Model no. VX54F

Includes pre-molar Flat and box, molar Flat.

NotesA

NotesNo

What to do if it goes wrong

Getting in touch

SolutionProblem

There is an accessory missing

- Check the 'This pack contains' panel on the box to make sure the part is included with your vacuum cleaner.

Why won't the vacuum cleaner pick up?

• The dirt container may not be correctly fitted, remove the dirt container from the vacuum cleaner and check it's assembled correctly, refl ensuring it's locked into place.
• The separator/shroud are blocked. Go to 'Taking care of your machine'
  • The separator/shroud are incorrectly fitted. Go to 'Taking care of your machine'
• The "filer may be clogged, clean the filter. Go to 'Taking care of your machine'.
• The dirt container may be blocked, empty the dirt container. Go to 'Taking care of your machine'.
• There may be a blockage in the hose/tube. Disconnect from the vacuum cleaner and carefully remove any blockages. Go to 'Let's talk technica'.

Why does my vacuum cleaner have no power?

• The plug may not be fully pushed into the electrical socket.
- The motor: hermostat may have trioped. If his has happened, unplug the vacuum cleaner. Remove and empty the dirt container and check the hose for blockages. Clean the filters and allow the vacuum cleaner to cool for approximately 1 hour if you have washed the filters you will need to wait 24 hours or the filters to dry dry before pulling them back into the vacuum cleaner).

- The "filters may be clogged, clean the filter. Go to Taking care of your machine".

Why is dust escaping from the vacuum?

IMPORTANT: To reduce the risk of personal injury, unplug the vacuum before performing maintenance/troubleshooting checks.

Taking care of you

We're here if you need us. For trouble shooting, simply call or visit:

Australia: 1300 361 505*

New Zealand: 0800 800 900*

vax.com.au

vax.co.nz

*Monday-Friday 8.30am to 5.00pm

* Calls are charged at the standard local rate. These make a note of the serial number and model number of the vacuum cleaner before calling.

vax

Distributed by Techtronic Industries Australia Pty. Ltd.

31 Gilby Road, Mt Waverley, VIC 3149 Australia.

Careline AU: 1300 361 505 www.vax.com.au

Careline NZ: 0800 800 900 www.vax.co.nz