99-7332 - Kit voiture Metra - Free user manual and instructions
Find the device manual for free 99-7332 Metra in PDF.
User questions about 99-7332 Metra
0 question about this device. Answer the ones you know or ask your own.
Ask a new question about this device
Download the instructions for your Kit voiture in PDF format for free! Find your manual 99-7332 - Metra and take your electronic device back in hand. On this page are published all the documents necessary for the use of your device. 99-7332 by Metra.
USER MANUAL 99-7332 Metra
INSTALLATION INSTRUCTIONS FOR PART 99-7332
APPLICATIONS
Hyundai Elantra
(Radio Delete Models)
2007-2010
99-7332
KIT FEATURES
• DIN Radio Provision with Pocket
• ISO Radio Provision with Pocket
natural_image
Front view of a car dashboard with air vent, grille, and central control panel (no visible text or symbols)KIT COMPONENTS
natural_image
Technical line drawing of a mechanical bracket or frame assembly (no text or symbols)
Wiring & Antenna Connections (sold separately)
• 70-1004 - Hyundai 2006-up / Kia2004-up Harness
• 70-7303 - Hyundai / Kia Harness 2009
• 40-KI11 - Kia Antenna Adapter 2007-up
TOOLS REQUIRED:
Small Flat Blade Screwdriver/ Panel Removal Tool
• Phillips Screwdriver
TABLE OF CONTENTS
Dash Disassembly
- Hyundai Elantra (Radio Delete Models) 2007-2010 ....1
Kit Assembly
- DIN Radio Provision with Pocket 2
- ISO Radio Provision with Pocket .... 3
Final Assembly 4
*Note:
Refer also to the instructions included with the aftermarket radio.
HYUNDAI ELANTRA
(RADIO DELETE MODELS) 2007-2010
1 Disconnect the negative battery terminal to prevent an accidental short circuit.
2 Unclip the panel surrounding the radio including the a/c vents and hazard switch. Unplug the hazard switch and remove the panel. (Figure A)
3 Remove (4) Phillips screws securing the blank plate/pocket covering the radio cavity and remove the plate. (Figure B)
Continue to kit assembly.
natural_image
Top-down line drawing of a car headrest with air vent and control knobs (no text or symbols)
natural_image
Top-down diagram of a car headrest with internal components and directional arrows indicating orientation (no text or symbols)DIN RADIO PROVISION WITH POCKET
*Note: Refer also to the instructions included with the aftermarket radio.
1 Slide the DIN cage into the Radio Housing and secure by bending the metal locking tabs outward. (Figure A)
2 Slide the aftermarket radio into the cage until it snaps into place. (Figure B)
Continue to final assembly.
natural_image
Illustration of a hand using a tool to adjust or install electronic components on a device chassis (no text or symbols visible)
natural_image
Technical line drawing of a mechanical device with mounting brackets and control panel (no text or symbols)ISO RADIO PROVISION WITH POCKET
*Note: Refer also to the instructions included with the aftermarket radio.
1 Mount the ISO Brackets to the aftermarket radio using the screws supplied with the radio. (Figure A)
2 Slide the radio into the radio opening until the side clips snap into place. (Figure B)
3 Snap the trim plate onto the front of the Radio Housing. (Figure B)
Continue to final assembly.
natural_image
Line drawing of a hand using a screwdriver to adjust or install an electronic device (no text or symbols present)
text_image
B RIGHT SIDE CLIPFINAL ASSEMBLY
text_image
A B C D(A) Strip wire ends back 1/2"
B) Twist ends together
C) Solder
D) Tape
1 Locate the factory wiring harness in the dash. Metra recommends using the proper mating adapter and making connections as shown. (Isolate and individually tape off the ends of any unused wires to prevent electrical short circuit.)
2 Re-connect the negative battery terminal and test the unit for proper operation.
3 Reassemble radio and dash assemblies in reverse order of disassembly.
FINAL WIRING CONNECTIONS
Make wiring connections using the EIA color code chart shown below and the instructions included with the head unit. Metra recommends making connections as shown below; Strip, Splice, Solder, Tape. Isolate and individually tape off ends of any unused wires to prevent electrical short circuit.
METRA / EIA WIRING CODE
12V Ignition / Acc. .... . Red
12V Batt / Memory.....Yellow
Ground..... Black*
Power Antenna. . . . . . . . . Blue
Amp Turn-On .... Blue / White
Amp Ground. .... Black / White
Illumination ..... Orange
Dimmer ..... Orange / White
Right Front (+) ..... Gray
Right Front (-)..... Gray/ Black
Left Front (+) ..... White
Left Front (-)..... White / Black
Right Rear (+)....Violet
Right Rear (-) ..... Violet / Black
*NOTE: When a Black wire is not present, ground radio to vehicle chassis.
All colors may not be present on all leads due to manufacturer's specifications.
99-7332 INSTRUCTIONS