107-TO8HG - Kit voiture Metra - Free user manual and instructions

USER MANUAL 107-TO8HG Metra

Interior view of a car dashboard with a digital display and control panel (no visible text or symbols)

Toyota Camry 2021-2024

Visit MetraOnline.com for more detailed information about the product and up-to-date vehicle specific applications

KIT FEATURES

• Designed for Pioneer modular radios with the 6.8" screen Note – see manufacturer for current models.
• Painted high-gloss black

KIT COMPONENTS

• A) Radio housing back panel • B) Pioneer chassis brackets • C) Pioneer screen brackets • D) Factory 9" screen trim panel
• E) Factory 7" screen trim panel • F) Panel clip mounts • G) (8) #8 x 3/8" Phillips screws • H) (4) #4 x 3/8" Phillips screws

A

Technical line drawing of a mechanical housing or frame component (no text or symbols)

• 

F

C

[Non-Text]

D

• 

TABLE OF CONTENTS

Dash Disassembly....2-3 Kit Assembly....4-5

WIRING & ANTENNA CONNECTIONS (sold separately)

Wiring Harness: Visit metraonline.com for audio/video and steering wheel control interface options. Antenna Adapter: 40-LX11

TOOLS REQUIRED

• Panel removal tool • Phillips screwdriver
• 10mm Socket wrench

Attention! With the key out of the ignition, disconnect the negative battery terminal before installing this product. Ensure that all installation connections are secure before cycling the ignition to test this product.

DASH DISASSEMBLY

1. Unclip and remove the dashboard trim panel below the climate cont (Figure A)

rols, board box.

1. Unclip and remove the lower dashboard trim panel directly above the glovebox. (Figure B)

Interior view of a car dashboard and steering wheel (no text or symbols visible)

(Figure B) (Figure D)

1. For models with a push button state, Unclip the Start/Stop button trim and set it to the side. (Figure C) For models without a push button, Unclip and remove the trim panel left of the radio/climate control panel (Figure D)

Continued on the next page

rt: panel start: to the nel.

(Figure C) (Figure A)

Interior view of a car dashboard and infotainment system (no visible text or symbols)

DASH DISASSEMBLY (CONT.)

1. Unclip and remove the upper dashboard trim panel with passenger A/C vent. (Figure E)
2. Unclip and remove the climate controls (Figure F)

Technical line drawing of a car interior showing dashboard and steering wheel (no text or symbols)

(Figure E) (Figure G)

1. Unclip and remove the A/C vent trim panel including the passenger air bag light. (Figure G)
2. Remove (4) 10mm screws securing the radio panel, then unplug and remove the panel. (Figure H)

Continue to Kit Preparation

Line drawing of a car interior showing dashboard, steering wheel, and dashboard components (no text or symbols)

Technical line drawing of a mechanical assembly with no visible text or symbols

Interior view of a car dashboard with a mounted touchscreen device and control panel (no visible text or symbols)

(Figure F) (Figure H)

KITASSEMBLY

1. Attach the Pioneer screen brackets to the Pioneer screen. Note: The screen brackets are marked for 9 inch screen. The other holes are for the 6.8 inch screen. (Figure A)
2. Attach the Pioneer chassis brackets to the Pioneer radio chassis. (Figure B)

Technical diagram of a mechanical assembly with two metal brackets and a central frame, showing alignment lines (no text or symbols)

1. Connect the cable from the chassis to the Pioneer radio screen then attach the screen to the radio housing back panel using (4) #8 x 3/8" Phillips screws supplied. (Figure C)
2. Attach the Pioneer radio chassis to the radio housing back panel using (4) #8 x 3/8" Phillips screws supplied. (Figure D)

Continued on the next page

Technical illustration of a mechanical assembly with two views, showing internal components and alignment lines (no text or symbols)

(Figure C) (Figure A)

Technical line drawing of a mechanical component with mounting brackets and mounting holes (no text or symbols)

Technical line drawing of a device with a mounted component and a screen (no text or symbols)

(Figure D) (Figure B)

KIT ASSEMBLY (CONT.)

1. Attach the clip brackets to the radio housing back panel using (4) #4 x 3/8" Phillips screws supplied. (Figure E)
2. Remove (5) factory clips from the factory radio housing and attach to the radio housing back panel.
3. Attach (6) panel clips to the factory 9" screen trim panel then clip it onto the radio housing back panel. (Figure F) Note: For factory 7" screen trim panel attach (6) panel clips to the radio housing back panel. (Figure G)
4. Reassemble the dash in reverse order of disassembly to complete the installation.

Technical line drawing of a mechanical assembly with no visible text or symbols

Technical line drawing of a mechanical assembly with no visible text or symbols

(Figure F) (Figure E)

Technical line drawing of a device frame assembly with no visible text or symbols

(Figure G)

Having difficulties? We're here to help.

Contact our Tech Support line at:

386-257-1187

Or via email at:

[e-mail]

Tech Support Hours (Eastern Standard Time)

Monday - Friday: 9:00 AM - 7:00 PM

Saturday: 10:00 AM - 5:00 PM

Sunday: 10:00 AM - 4:00 PM

Metra recommends MECP certified technicians