AXTC-CL2 - Car stereo AXESS - Free user manual and instructions
Find the device manual for free AXTC-CL2 AXESS in PDF.
User questions about AXTC-CL2 AXESS
0 question about this device. Answer the ones you know or ask your own.
Ask a new question about this device
Download the instructions for your Car stereo in PDF format for free! Find your manual AXTC-CL2 - AXESS and take your electronic device back in hand. On this page are published all the documents necessary for the use of your device. AXTC-CL2 by AXESS.
USER MANUAL AXTC-CL2 AXESS
natural_image
Electronic component with black plastic housing, gray connector, and various colored wires (no visible text or symbols)INTERFACE COMPONENTS
- AXTC-CL2 interface
- AXTC-CL2 harness
- 3.5mm adapter
APPLICATIONS
See inside front cover
GM Data Interface with SWC 2000-2013
INTERFACE FEATURES
- Provides retained accessory power (10-amp)
- Provides illumination, parking brake, reverse, and speed sense outputs
- Retains warning chimes through an onboard speaker
- Retains audio controls on the steering wheel
-
Designed to be compatible with all major radio brands
• Auto detects vehicle type, radio connection, and preset controls -
Ability to dual assign steering wheel control buttons
- Retains memory settings even after battery disconnection or interface removal (nonvolatile memory)
- Designed for non-amplified models, or when bypassing a factory amplifier
- Retains balance and fade
- Micro-B USB updatable
Product Info
TABLE OF CONTENTS
Applications 2
Connections....3
Programming......4-5
Troubleshooting....6
TOOLS & INSTALLATION ACCESSORIES REQUIRED
- Crimping tool and connectors, or solder gun, solder, and heat shrink
• Tape - Wire cutter
- Zip ties
Visit AxxessInterfaces.com for more detailed information about the product and up-to-date vehicle specific applications.
ATTENTION: With the key out of the ignition, disconnect the negative battery terminal before installing this product. Ensure that all installation connections, especially the air bag indicator lights, are plugged in before reconnecting the battery or cycling the ignition to test this product. NOTE: Refer also to the instructions included with the aftermarket accessory before installing this device.
APPLICATIONS
Buick
| Century | 2004-2005 | (hold) |
| Lacrosse | 2005-2009 | (hold) |
| Rainier | 2004-2007 | (tap) |
| Regal | 2004 | (hold) |
| Rendezvous | 2002-2007 | (hold) |
| Terraza | 2005-2007 | (hold) |
Cadillac
| Escalade (1)......2003-2006 | (tap) |
| Escalade ESV (1)......2003-2006 | (tap) |
| Escalade EXT (1)......2003-2006 | (tap) |
Chevrolet
| Avalanche....2003-2006 | (tap) |
| Cavalier....2000-2005 | (tap) |
| Colorado....2004-2012 | (tap) |
| Corvette....2005-2013 | (hold) |
| Express....2003-2007 | (tap) |
Chevrolet (SWO)*
| Impala....2000-2005 | (hold) |
| Kodiak C4500-C8500....2003-2009 | (tap) |
| Malibu....2001-2003 | (tap) |
| Malibu Classic....2004-2005 | (tap) |
| Monte Carlo....2000-2005 | (hold) |
| Silverado....2003-2006 | (tap) |
| Silverado Classic....2007 | (tap) |
| SSR....2003-2006 | (tap) |
| Suburban....2003-2006 | (tap) |
| Tahoe....2003-2006 | (tap) |
| Trailblazer....2002-2009 | (tap) |
| Uplander....2005-2008 | (hold) |
GMC
| Canyon......2004-2012 | (tap) |
| Envoy......2002-2009 | (tap) |
| Savana......2003-2007 | (tap) |
GWW(cont)
| Sierra......2003-2006 | (tap) |
| Sierra Classic......2007 | (tap) |
| Top Kick C4500-C8500..2005-2009 | (tap) |
| Yukon......2003-2006 | (tap) |
| Yukon XL......2003-2006 | (tap) |
Hummer
| H2 (1) | 2003-2007 | (tap) |
| H3 | 2006-2010 | (tap) |
| H3T | 2006-2010 | (tap) |
Isuzu
| Ascender......2003-2008 | (tap) |
| H Series......2003-2008 | (tap) |
| I Series pickups......2006-2008 | (tap) |
Oldsm6WTe*
| Alero | 2001-2004 | (hold) |
| Bravada | 2002-2004 | (tap) |
| Intrigue | 2002 | (hold) |
| Pontiac | ||
| Aztec | 2001-2005 | (hold) |
| Grand Am | 2001-2005 | (hold) |
| Grand Prix | 2004-2008 | (hold) |
| Montana SV6 | 2005-2006 | (hold) |
| Sunfire | 2000-2005 | (tap) |
SAAB
| 9-7X | 2005-2009 | (tap) |
| Saturn | ||
| Relay | 2005-2007 | (hold) |
(1) These vehicles are standard for an amp and must be bypassed.
\* SWC Programming Sequence
(hold) Press and hold the Volume Up button to program the interface.
(tap) Tap the Volume Up button to program the interface.
CONNECTIONS
text_image
Reset Button LED Aftermarket Radio (radio's features may vary) Front Icar Sub Aux IN Rear View SWC Vehicle Connector 3.5mm Adapter (for vehicles without Steering wheel controls or aftermarket radios with a wire for SWC) Boss (with SWC wire): Key 1 (Gray) - Brown Kenwood / JVC (with SWC wire): Blue/Yellow - Brown XITE: SWC-2 - Brown Universal SWC1 - Brown Key 1/2 OF SWC2 - Brown/White Radio* After programming, assign SWC buttons within radio menu 3.5mm Adapter for Vehicles without Steering wheel controls 1) From the 3.5mm adapter, tie the Brown and Brown/White wires together with tape or connector 2) Connect the 3.5mm adapter to the 3.5mm jack from the AXTC-CL2 Harness 3) Program the AXTC-CL2 per the instructions on pages 4 and 5. Disregard steps 4 & 5 Radio Connections Black - Ground Yellow - Battery power Red - Accessory power Orange - Illumination * Orange (labeled IFACE ILL) - Illumin Blue/White - Amp turn-on Blue/Pink - VSS/Speed-Sense Green/Purple - Reverse signal Light Green - Parking brake Gray - Front right speaker + Gray/Black - Front right speaker - White - Front left speaker + White/Black - Front left speaker - Green - Rear left speaker + Green/Black - Rear left speaker - Purple - Rear right speaker + Purple/Black - Rear right speaker -PROGRAMMING (hold)
1.
Open the driver's door, and keep open during the programming process.
2.
Cycle the ignition on.
3.
Connect the AXTC-CL2 harness to the AXTC-CL2 interface, and then to the wiring harness in the vehicle.
*4.
Locate the Volume Up button on the steering wheel. Program the interface by pressing and holding the Volume Up button until the LED stops flashing.
*Only applicable if vehicle came with steering wheel controls
*5.
The LED will flash Green & Red while the interface programs the radio to the steering wheel controls. Once programmed, the LED will go out, then produce a pattern which will identify the radio type installed. Refer to the Radio LED Feedback section under Troubleshooting for radio types.
*Only applicable if vehicle came with steering wheel controls
6.
The LED will go out, then once again quickly flash Green & Red while the interface programs itself to the vehicle. Once programmed, the LED will go out again, then turn solid Green.
7.
Cycle the ignition off, then back on.
8.
Test all functions of the installation for proper operation.
PROGRAMMING (tap)
1.
Open the driver's door, and keep open during the programming process.
2.
Cycle the ignition on.
3.
Connect the AXTC-CL2 harness to the AXTC-CL2 interface, and then to the wiring harness in the vehicle.
*4.
Locate the Volume Up button on the steering wheel. Program the interface by tapping the Volume Up button at a heartbeat pace until the LED stops flashing.
*Only applicable if vehicle came with steering wheel controls
*5.
The LED will flash Green & Red while the interface programs the radio to the steering wheel controls. Once programmed, the LED will go out, then produce a pattern which will identify the radio type installed. Refer to the Radio LED Feedback section under Troubleshooting for radio types.
*Only applicable if vehicle came with steering wheel controls
6.
The LED will go out, then once again quickly flash Green & Red while the interface programs itself to the vehicle. Once programmed, the LED will go out again, then turn solid Green.
7.
Cycle the ignition off, then back on.
8.
Test all functions of the installation for proper operation.
TROUBLESHOOTING
1.
LED Light
If the interface fails to function, press and release the reset button, then repeat the programming process from step 4 to try again.
Final LED Feedback
At the end of programming the LED will turn Solid Green which indicates programming was successful. If the LED didn't turn Solid Green, reference the list below to understand which programming section the problem may stem from.
| LED Light | Radio Programming Section | Vehicle Programming Section |
| Solid Green | Pass | Pass |
| Slow Red Flash | Fail | Pass |
| Slow Green Flash | Pass | Fail |
| Solid Red | Fail | Fail |
Note: If the LED shows Solid Green for Pass (indicating everything programmed correctly), yet the steering wheel controls don't work, make sure that the 3.5mm jack is plugged in, and plugged into the correct jack in the radio. Once corrected, press the reset button, then program again.
QR Code Scan Here
Further troubleshooting steps and information can be located at:
axxessinterfaces.com/product/AXTC-CL2
Having difficulties? We're here to help.
Contact our Tech Support line at:
386-257-1187
Or via email at:
techsupport@metra-autosound.com
Tech Support Hours (Eastern Standard Time)
Monday - Friday: 9:00 AM - 7:00 PM
Saturday: 10:00 AM - 7:00 PM
Sunday: 10:00 AM - 4:00 PM
KNOWLEDGE IS POWER
Enhance your installation and fabrication skills by enrolling in the most recognized and respected
enrolling in the most recognized and resp mobile electronics school in our industry.
Log onto www.installerinstitute.edu or call
386-672-5771 for more information and take steps toward a better tomorrow.
Metra recommends MECP certified technicians