AXGM-08 - Television Axxess - Free user manual and instructions

Product Type	Vehicle Interface Module
Brand	AXESS
Model	AXGM-08
Compatible Vehicles	2005-2006 Chevrolet Equinox, 2006 Pontiac Torrent
Power Supply	12V DC, 10A accessory output
Main Functions	Retains RAP, NAV outputs (parking brake, reverse, speed sense), chimes, OnStar/BT, balance/fade; provides accessory power
Audio Adjustment	Adjustable audio and chime level via potentiometer
OnStar Level	Adjustable via steering wheel controls or ground tap
Steering Wheel Controls	Compatible with optional AXSWC (sold separately)
Speaker Outputs	Front left/right, rear left/right with positive and negative wires
Pre-wired Harness	16-pin harness with stripped leads, AXGM-08 harness, 12-pin AXSWC harness
Updatable	Via AXUSB-CBL (sold separately)
Chime Retention	Yes, with adjustable level
Safety Warnings	Do not remove factory radio with key on; connect all accessories before cycling ignition
Installation Requirements	Wire cutter, crimp tool, solder gun, tape, small flat-blade screwdriver
Dimensions (approx.)	Compact module (exact not specified)
Weight (approx.)	Lightweight (exact not specified)

Frequently Asked Questions - AXGM-08 Axxess

What vehicles is the AXGM-08 compatible with?

The AXGM-08 is designed for 2005-2006 Chevrolet Equinox and 2006 Pontiac Torrent with amplified factory systems.

How do I initialize the AXGM-08 interface?

With key off, connect all harnesses. Turn key to ignition position; the radio should come on within 60 seconds. If not, check connections. Turn off, then to accessory position and test functions.

What does the Blue/White wire connect to?

Connect the Blue/White wire to the amp turn-on wire of the aftermarket radio to enable sound from the factory amplifier.

How do I adjust the audio level?

Turn the vehicle and radio on, volume to 3/4. Use a small flat-blade screwdriver to turn the potentiometer clockwise to raise or counterclockwise to lower the audio level.

How do I set the chime volume?

With vehicle on, turn off and leave keys in ignition. Open driver's door, wait 10 seconds. Adjust the potentiometer (same as audio) to desired level, then remove keys to lock.

Can I adjust OnStar volume without steering wheel controls?

Yes, locate the Black/Yellow wire on the AXGM-08 harness. While OnStar is speaking, tap that wire to ground to adjust the level.

What is the purpose of the Brown wire?

The Brown wire connects to the aftermarket radio's mute wire. If not connected, the radio will turn off when OnStar is activated.

Do I need to install the AXSWC separately?

The AXSWC is optional and sold separately. It connects to the pre-wired 12-pin harness to retain steering wheel audio controls. Install and program it after initializing the AXGM-08.

What should I do if the radio does not come on during initialization?

Turn the key off, disconnect the interface, check all connections, reconnect, and try again. Ensure the vehicle battery is connected and ignition is on.

Does the AXGM-08 retain factory chimes?

Yes, it retains chimes and allows adjustment of their volume via a potentiometer.

USER MANUAL AXGM-08 Axxess

Installation instructions for part AXGM-08

AXGM-08

GM Data Interface

2005-2006

INTERFACE FEATURES

• Provides accessory power (12-volt 10-amp)
- Retains R.A.P. (retained accessory power)
- Provides NAV outputs (parking brake, reverse, speed sense)
- Retains chimes
- Pre-wired AXSWC harness (AXSWC sold separately)

• Retains OnStar / OE Bluetooth
- Adjustable OnStar level
- Designed for amplified models
• Retains balance and fade
- AXUSB-CBL (sold separately) updatable

INTERFACE COMPONENTS

- AXGM-08 interface • AXGM-08 harness

• 16-pin harness with stripped leads

APPLICATIONS

CHEVROLET		PONTIAC
Equinox	2005-2006	Torrent	2006

Table of Contents

Connections to be made....2

Installing the AXGM-08 3

Initializing the AXGM-08 3

Adjusting the AXGM-08 3

TOOLS REQUIRED

• Wire cutter • Crimp tool • Solder gun • Tape
• Connectors (example: butt-connectors, bell caps, etc.)
• Small flat-blade screwdriver

CAUTION! All accessories, switches, climate controls panels, and especially air bag indicator lights must be connected before cycling the ignition. Also, do not remove the factory radio with the key in the on position, or while the vehicle is running.

AXGM-08

Connections to be made

From the 16-pin harness with stripped leads to the aftermarket radio:

• Connect the Red wire to the accessory wire.
  Note: If installing an AXSWC (sold separately), there will be an accessory wire there to connect as well.
• Connect the Blue/White wire to the amp turn on wire. This wire must be connected to hear sound from the factory amplifier.
• If the aftermarket radio has an illumination wire, connect the Orange/White wire to it.
• If the aftermarket radio has a mute wire, connect the Brown wire to it. If the mute wire is not connected, the radio will turn off when OnStar is activated.
• Connect the Gray wire to the right front positive speaker output.
• Connect the Gray/Black wire to the right front negative speaker output.
• Connect the White wire to the left front positive speaker output.
• Connect the White/Black wire to the left front negative speaker output.
• Connect the Green wire to the left rear positive speaker output.
• Connect the Green/Black wire to the left rear negative speaker output.
• Connect the Purple wire to the right rear positive speaker output.
• Connect the Purple/Black wire to the right rear negative output.

The following (3) wires are only for multimedia/navigation radios that require these wires.

• Connect the Blue/Pink wire to the VSS/speed sense wire.
• Connect the Green/Purple wire to the reverse wire.
• Connect the Light Green wire to the parking brake wire.

From the AXGM-08 harness to the aftermarket radio:

• Connect the Black wire to the ground wire.
• Connect the Yellow wire to the battery wire.
• The Black/Yellow wire is used for OnStar level adjustment for models that do not come equipped with steering wheel controls. Refer to the OnStar level Adjustment section for further instructions.

12-pin pre-wired AXSWC harness:

- This harness is to be used along with the optional AXSWC (not included) to retain steering wheel audio controls. If the AXSWC is not being used, disregard this harness. If it will be used, please refer to the AXSWC instructions for radio connections and programming.

Note: Disregard the harness that comes with the AXSWC.

- Connect the Red wire to the accessory wire.

AXGM-08

Installing the AXGM-08

With the key in the off position:

• Connect the 16-pin harness with stripped leads, and the AXGM-08 harness, into the interface.
• Connect the AXGM-08 harness to the wiring harness in the vehicle.

Note: If using the AXSWC, connect it after you initialize and test the AXGM-08, with the key in the off position.

Initializing the AXGM-08

Attention! If the interface loses power for any reason, the following steps will need to be performed again. Also, if installing an AXSWC, connect it after you initialize and test the interface/radio, with the key in the off position.

- Turn the key (or push-to-start button) to the ignition position and wait until the radio comes on.

Note: If the radio does not come on within 60 seconds, turn the key to the off position, disconnect the interface, check all connections, reconnect the interface, and then try again.

- Turn the key to the off position, pause for a moment, and then to the accessory position. Test all functions of the installation for proper operation, before reassembling the dash.

Adjusting the AXGM-08

Audio level adjustment:

• With the vehicle and radio turned on, turn the volume up 3/4 of the way.
• With a small flat-blade screwdriver, adjust the potentiometer clockwise to raise the audio level; counterclockwise to lower the audio level.
• Once at a desired level, audio level adjustment is complete.

Chime level adjustment:

• With the vehicle on, turn it off and leave the keys in ignition. Open the driver's door; chimes will be heard.
• Wait 10 seconds, and then with a small screwdriver, turn the potentiometer clockwise to raise the chime level; counterclockwise to lower the chime level.
• When the chime is at a desired level, remove the keys from the ignition. This will lock the chime volume at its current level.

OnStar Level Adjustment:

• Press the OnStar button to activate it.
• While OnStar is speaking, press the VOLUME UP or VOLUME DOWN button on the steering wheel to raise or lower the OnStar level.
• If the vehicle does not come equipped with steering wheel controls, or they no longer function, locate the Black/Yellow wire on the AXGM-08 harness.
• While OnStar is speaking, tap the Black/Yellow wire to ground. Once the OnStar level is set, it will stay at that level until the Black/Yellow wire is tapped to ground again.

Installation instructions for part AXGM-08

IMPORTANT

If you are having difficulties with the installation of this product, please call our Tech Support line at 1-800-253-TECH. Before doing so, look over the instructions a second time, and make sure the installation was performed exactly as the instructions are stated. Please have the vehicle apart and ready to perform troubleshooting steps before calling.

KNOWLEDGE IS POWER

Enhance your installation and fabrication skills by enrolling in the most recognized and respected mobile electronics school in our industry. Log onto www.installerinstitute.com or call 800-354-6782 for more information and take steps toward a better tomorrow.

Metro recommends MECP certified technicians