95-7605A - Unspecified AXESS - Free user manual and instructions
Find the device manual for free 95-7605A AXESS in PDF.
User questions about 95-7605A AXESS
0 question about this device. Answer the ones you know or ask your own.
Ask a new question about this device
Download the instructions for your Unspecified in PDF format for free! Find your manual 95-7605A - AXESS and take your electronic device back in hand. On this page are published all the documents necessary for the use of your device. 95-7605A by AXESS.
USER MANUAL 95-7605A AXESS
INSTALLATION INSTRUCTIONS FOR PART 95-7605
APPLICATIONS
INFINITI G35 Coupe 2005-07
INFINITI G35 Sedan 2005-06
Painted And Finished To Match Factory Dash
95-7605
KIT FEATURES
• ISO Double DIN Radio Provision
- Stacked ISO Mount Units Provision
KIT COMPONENTS
A) Radio Housing • B) Climate Control Cable
natural_image
Interior view of a car dashboard with air conditioner and touchscreen (no visible text or symbols)
natural_image
Technical line drawing of a mechanical component with mounting holes and a central circular feature (no text or symbols)
natural_image
Pure electrical circuit lines without any symbolsTOOLS REQUIRED:
Small Flat Blade Screwdriver/ Panel Removal Tool • Phillips Screwdriver • Hook Tool
natural_image
Line drawings of four different screwdriver tools (no text or symbols)TABLE OF CONTENTS
Dash Disassembly
- Infiniti G35 Coupe 2005-2007/G35 Sedan 2005-06 .....1,2
Kit Assembly
Double DIN / Stacked ISO Mount Units Provision ....3
Final Assembly 4
*Note:
Refer also to the instructions included with the aftermarket radio.
INFINITI G35 Coupe 2005-07 / INFINITI G35 Sedan 2005-06
1 Disconnect the negative battery terminal to prevent an accidental short circuit.
2 Push down on the collar below the shift knob to unclip. Using a small screwdriver or hook tool remove the spring clip to release and remove the shift knob. (Figure A)
3 Unclip and remove the shifter trim panel including the ashtray/cigarette lighter. (Figure B)
4 Remove (2) Phillips screws (exposed under the trim panel removed in step 3) from the panels on the left and right side of the radio/climate control panel assembly. (Figure C)
5 Unclip and remove the trim panels on the left and right side of the radio/climate control panel assembly.
(Figure D)
6 Unclip and remove the thin plastic trim piece at top edge of dash. (Figure E)
7 Unclip and remove the hood panel above the clock on the top of the dash. (Figure F)
Continued on page 2.
natural_image
Line drawing of a car air intake manifold with control panel and directional arrows (no text or symbols)
text_image
A 1 2 3
natural_image
Diagram of a car gear shift lever with labeled component B (no text or symbols beyond label)
text_image
C
natural_image
Diagram of a car dashboard with directional arrows indicating movement or flow (no text or symbols present)INFINITI G35 Coupe 2005-07 / INFINITI G35 Sedan 2005-06
8 Unclip and remove the trim panel at the bottom of the clock panel then remove the (1) Phillips screw exposed below it. (Figure G)
9 Remove (2) Phillips screws below the radio/climate control panel and (2) Phillips screws at the top of the radio/climate control panel assembly (between the a/c vents). (Figure H)
10 Unclip the radio/climate control panel/factory bracket. Unplug and remove the assembly. (Figure H)
11 Unclip the ribbon cable joining the radio/climate control panel to the radio chassis. (Figure I)
12 Remove (8) Phillips screws securing the radio chassis and (6) Phillips screws securing the radio/climate control panel to the factory bracket assembly. Save screws and bracket for re-use during kit assembly.
Continue to kit assembly.
natural_image
Technical diagram of a mechanical assembly with directional arrows indicating motion or force (no text or symbols present)
text_image
F 79F OUTSIDE
text_image
G 79F OUTSIDE
text_image
H
text_image
J 4 SCREWS ON EACH SIDE
text_image
K 3 SCREWS ON EACH SIDEDOUBLE DIN/ISO STACK MOUNT UNITS PROVISION
*Note: Refer also to the instructions included with the aftermarket radio.
1 Position the aftermarket double DIN or stacked ISO mount unit(s) into the factory bracket assembly and secure using the screws supplied with the aftermarket unit(s). (Figure A)
2 Attach the radio housing to the factory bracket assembly using the factory hardware. (Figure B)
3 Connect the black end of the climate control cable to the climate controls in the radio housing and connect the other end of the cable to the factory climate control harness during final assembly.
Continue to final assembly.
natural_image
Technical line drawing of a mechanical device with multiple components and screw fasteners (no text or symbols)
natural_image
Technical line drawing of a mechanical device with internal components and mounting brackets (no text or symbols)FINAL ASSEMBLY
text_image
A B C D(A) Strip wire ends back 1/2"
B) Twist ends together
C) Solder
D) Tape
1 Locate the factory wiring harness in the dash. Metra recommends using the proper mating adapter and making connections as shown. (Isolate and individually tape off the ends of any unused wires to prevent electrical short circuit.)
2 Re-connect the negative battery terminal and test the unit for proper operation.
3 Reassemble radio and dash assemblies in reverse order of disassembly.
FINAL WIRING CONNECTIONS
Make wiring connections using the EIA color code chart shown below and the instructions included with the head unit. Metra recommends making connections as shown below; Strip, Splice, Solder, Tape. Isolate and individually tape off ends of any unused wires to prevent electrical short circuit.
METRA / EIA WIRING CODE
| 12V Ignition / Acc. . . . . . . . Red | Right Front (+) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . |
| 12V Batt / Memory. . . . . . . . . . . . Yellow | Right Front (-). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Ground. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Power Antenna. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Amp Turn-On. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Amp Ground. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Illumination. . . . . . . . . . . . . . . . . . . . . . . . . Dimmer. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . |
*NOTE: When a Black wire is not present, ground radio to vehicle chassis. All colors may not be present on all leads due to manufacturer's specifications.
NOTES
95-7605 INSTRUCTIONS