99-3302 - Kit voiture Metra - Free user manual and instructions

USER MANUAL 99-3302 Metra

INSTALLATION INSTRUCTIONS FOR PART 99-3302

APPLICATIONS

See application list inside

GM multi-kit

99-3302

KIT FEATURES

• DIN Mount Radio Provision with Pocket
• ISO Mount Radio Provision with Pocket
- Painted To Match Factory Dash

Interior view of a car infotainment device showing the front panel and control buttons (no readable text or symbols)

KIT COMPONENTS

Technical line drawing of a mechanical housing or enclosure component (no text or symbols)

B C DA

Technical line drawing of two mechanical bracket components (no text or symbols)

Simple line drawing of a rectangular frame with four corner slots (no text or symbols)

WIRING & ANTENNA CONNECTIONS (Sold Separately)

WiringHarness:

• Please see www.metraonline.com for specific interface applications
  Antenna Adapter:
  • 40-CR10 - Chrysler antenna adapter 2002-up
  • 40-GM10 - GM antenna adapter 1988-up

TOOLS REQUIRED

Small Flat Blade Screwdriver • Panel Removal Tool • Phillips Screwdriver Socket Set • Cutting Tool

Line drawings of five different screwdriver tools (no text or symbols)

Metra recommends disconnecting the negative battery terminal before beginning any installation. All accessories, switches, and especially air bag indicator lights must be plugged in before reconnecting the battery or cycling the ignition.

*NOTE: Refer also to the instructions included with the aftermarket radio.

KNOWLEDGE IS POWER

Enhance your installation and fabrication skills by enrolling in the most recognized and respected mobile electronics school in our industry. Log onto www.installerinstitute.com or call 800-354-6782 for more information and take steps toward a better tomorrow.

Metra recommends MECP certified technicians

Table of Contents

Dash Disassembly

• Chevy Cobalt 2005-2010...4
• Chevy Equinox 2005-2006..5....
• Chevy HHR 2006-up...6.
• Chevy Malibu 2004-2007...7,8.
• Chevy Malibu 2008-up . . .9 . . . . . . . . . . . . . . . . . . . . . .
• Pontiac G5 2007-2009 . . 4.
• Pontiac G6 2005-2009...10
• Pontiac Solstice 2006-2009 .11.
• Pontiac Torrent 2006...5
• Saturn Aura 2007-2009...12......
• Saturn Ion 2006-2007 ....13....
• Saturn Sky 2006-2009....14....
• Saturn Vue 2006-2007....15.

Kit Assembly

DIN mount radio provision with pocket....16

ISO mount radio provision with pocket 17

Note: (Cobalt and G5 2005-2006)

To retain Onstar use 99-3303 instead.

Note: (Malibu and G6 only)

The Driver Information Center and radio are one unit. Removal of the radio will prohibit the vehicle owner from programming any of the features of the Driver Information Center. However once the features are programmed the vehicle will retain all the settings. An alternative kit 99-3303 includes a replacement driver information center with programming capabilities.

The 99-3303 does not allow for Double DIN installations.

Chevrolet Cobalt 2005-2010 Pontiac G5 2007-2009

1. Unclip and remove trim panel from above glove box. (Figure A)
2. Unclip upper edge of panel below steering column and let hang. Not necessary to remove completely. (Figure B)
3. Unclip and remove small trim panel to right of ignition switch. (Figure C)
4. Unclip and remove trim panel surrounding radio and climate controls. (Figure D)
5. Remove (4) 9/32 screws securing radio. Unplug and remove the radio. (Figure E) Continue to kit assembly

Line drawing of hands inserting a CD into a car air conditioner unit (no text or symbols)

(Figure A)

Line drawing of a hand inserting a device into a car air vent (no text or symbols)

(Figure C)

Line drawing of hands installing or adjusting a car air conditioner unit into the dashboard (no text or symbols visible)

(Figure D)

Line drawing of a car interior showing steering wheel, dashboard, and steering wheel (no text or symbols)

(Figure B)

Line drawing of a car infotainment device with hand operating controls (no text or symbols)

(Figure E)

Chevrolet Equinox 2005-2006 Pontiac Torrent 2006

1. Unsnap panel below power window switch and remove. Note: This allows you to unplug the window switch easier. (Figure A)
2. Unsnap and remove entire panel surrounding radio and shifter. (Figure B)
3. Remove (4) 9/32 screws securing radio. Unplug and remove the radio. (Figure C) Continue to kit assembly

Line drawing of hands installing or adjusting a mechanical component with arrows indicating assembly (no text or symbols)

(Figure A)

Line drawing of hands using a handheld device to interact with a car (no text or symbols visible)

(Figure B)

Hand operating a CD-ROM drive with a wrench, showing control panel and buttons (no text or symbols visible)

(Figure C)

Chevrolet HHR 2006-up

1. Unclip and remove entire panel surrounding radio and a/c controls including the a/c vents. (Figure A)
2. Remove (8) 9/32" screws securing radio and a/c control to remove radio. (Figure B)

Continue to kit assembly

Interior view of a car showing hands operating the dashboard and steering wheel (no text or symbols visible)

(Figure A)

Interior view of a car dashboard and steering wheel assembly (no text or symbols visible)

(Figure B)

Chevrolet Malibu 2004-2007

1. Unclip and remove wood grain/painted trim pieces from both sides of steering wheel. (Figure A)
2. Unclip and remove side panel from driver's side of dash with door open and remove (2) 7 mm screws. (Figure B)
3. Remove (2) 7 mm screws from bottom edge of panel below steering wheel, unclip panel and let hang. It is not necessary to completely remove panel. (Figure C)
4. Unclip and remove wood grain/painted trim piece from above glove box. (Figure D)
   Continued on next page

Diagram of a car's steering wheel and dashboard with directional arrows indicating components (no text or labels)

(Figure A)

Line drawing of a person using a tool to adjust or install a car door panel (no text or symbols visible)

(Figure B)

Illustration of a hand using a tool to adjust or install a car's seat frame (no text or symbols visible)

(Figure C)

Illustration of a car interior showing hands using a tool to adjust the seat area (no text or symbols visible)

(Figure D)

Chevrolet Malibu 2004-2007

1. Unclip and remove side panel from passenger side of dash with door open and remove (2) 7 mm screws from behind panel. (Figure E)
2. Remove (2) 7 mm screws from bottom of glove box then open box and squeeze sides together to open further and remove the remaining (4) 7 mm screws. Unclip the black vent cover under the glove box then unclip and remove entire glove box assembly. (Figure F)
3. Unclip and remove trim panel surrounding radio and climate controls. (Figure G)
4. Remove (4) 7 mm screws securing the radio and (2) 7 mm screws securing the climate control. Unplug and remove the radio. (Figure H)

Continue to kit assembly

Line drawing of a hand using a tool to cut or adjust a mechanical component (no text or symbols)

(Figure E)

Illustration of a hand using a tool to adjust or install a mechanical component, with arrows indicating motion (no text or symbols present)

(Figure F)

Technical line drawing of a car interior showing hand positioning and airflow direction (no text or symbols)

(Figure G)

Technical diagram of a mechanical device with directional arrows indicating motion or force (no text or symbols present)

(Figure H)

Chevrolet Malibu 2008-up

1. Unsnap and remove shifter trim. Note – start around shifter and be sure to pull down before back because this panel slides up under the radio/climate panels. (Figure A)
2. Remove (2) 8 mm screws from bottom of radio/climate panel.
3. Unsnap and remove the climate/radio panel and upper vent trim panel together. (They can be separated after removal) (Figure B,C)
4. Remove (6) 8 mm screws from radio and climate controls.
   Continue to kit assembly

Line drawing of a car dashboard with directional arrows indicating motion (no text or symbols)

(Figure A)

Line drawing of hands operating a car interior with control panel and buttons (no text or symbols)

(Figure B)

Illustration of hands using a tool to adjust or install a mechanical component (no text or symbols visible)

(Figure C)

Pontiac G6 2005-2009

1. Open glove box and remove (6) screws from outer edge then unclip and remove box. (Figure A)
2. Remove (4) screws from panel below steering column. Unclip and remove panel. (Figure B)
3. Unclip and remove center panel surrounding radio and A/C controls. (Figure C)
4. Remove (4) screws securing the radio. Unplug and remove the radio. (Figure D)
5. Unclip and remove center panel surrounding radio and A/C controls. (Figure C)
6. Remove (4) screws securing the radio. Unplug and remove the radio. (Figure D)
   Continue to kit assembly

Top View

(Figure A)

Technical line drawing of a mechanical assembly with no visible text or symbols

(Figure B)

Illustration of hands holding a vintage-style radio device with buttons and a screen, no text or symbols present

(Figure C)

Line drawing of a hand holding a mechanical device with circular components and adjustment knobs (no text or symbols)

(Figure D)

Pontiac Solstice 2006-2009

1. Open glove box and remove (6) screws from outer edge then unclip and remove box. (Figure A)
2. Remove (4) screws from panel below steering column. Unclip and remove panel. (Figure B)
3. Unclip and remove center panel surrounding radio and A/C controls. (Figure C)
4. Remove (4) screws securing the radio. Unplug and remove the radio. (Figure D)
5. Unclip and remove center panel surrounding radio and A/C controls. (Figure C)
6. Remove (4) screws securing the radio. Unplug and remove the radio. (Figure D)
   Continue to kit assembly

Diagram of a car dashboard with control panel and directional arrows indicating rotation (no text or symbols)

(Figure A)

Line drawing of a car gear shift lever with control panel and dashboard (no text or symbols)

(Figure B)

Diagram of a mechanical gear shift lever mechanism with directional arrows indicating motion (no text or symbols)

(Figure C)

Technical line drawing of a mechanical assembly with no visible text or symbols

(Figure D)

Saturn Aura 2007- 2009

1. Unclip and remove shifter trim ring. (Figure A)
2. Unclip and remove the center console trim panel, then remove (2) screws from bottom edge of dash trim panel. (Figure B)
3. Unclip and remove the key switch trim ring, then unclip and remove dash trim panel. (Figure C)
4. Remove (2) screws securing the climate controls.
5. Remove (4) screws securing the radio. Unplug and remove the radio.
   Continue to kit assembly

Line drawing of a car dashboard with control panel and gear shift (no text or symbols)

(Figure A)

Line drawing of a car dashboard and steering wheel assembly (no text or symbols)

(Figure B)

Diagram of car air intake system showing airflow direction and component placement (no text or labels)

(Figure C)

Saturn Ion 2006-2007

1. Unclip radio trim panel. (Figure A) Unplug connectors from trim panel and remove panel. (Figure B)
2. Remove (4) screws securing the radio. Unplug and remove the radio.
   Continue to kit assembly

Interior view of a car dashboard with steering wheel, dashboard controls, and air vent (no text or symbols visible)

(Figure A)

Diagram of a car dashboard with cable routing and directional arrows indicating movement (no text or symbols)

(Figure B)

Saturn Sky 2006- 2009

1. Unclip and remove side panel from driver's side of dash with door open and remove (2) 7 mm screws. (Figure A)
2. Remove (2) 7 mm screws from bottom edge of panel below steering wheel, unclip panel and remove panel.
3. Unclip and remove side panel from passenger side of dash with door open and remove (2) 7 mm screws from behind panel. (Figure B)
4. Open the glove box and disconnect the glove box dampener from the glove box assembly. Squeeze sides together to open further. (Figure C)
5. Remove (2) bolt covers from top edge of glove box frame. (Figure C)
6. Remove (5) bolts from glove box frame and remove frame. (Figure C)
7. Unsnap and remove climate control trim panel. (Figure D)
8. Remove (1) screw from lower left corner of radio trim panel and unplug connectors to remove panel. (Figure D)
9. Remove (4) screws securing the radio. Unplug and remove the radio. Continue to kit assembly

Technical diagram of a mechanical assembly with directional arrows and circular features (no text or symbols)

(Figure A)

Technical diagram of a mechanical component with arrows indicating motion or flow, no visible text or symbols

(Figure B)

Technical diagram of a car's front and side components with no visible text or symbols

(Figure C)

Technical line drawing of a car dashboard with air flow indicators (no text or symbols)

(Figure D)

1. Grasp the front edge of the shifter trim panel and pull outward and upward. (Figure A)
2. Squeeze the locking tabs located at the front edge of the shifter trim panel together to release the front edge of the panel from the center console. (Figure B)
3. Pull upward on the panel to release the remaining clips, and remove trim panel.
4. Remove (4) screws securing storage pocket and remove pocket. (Figure C)
5. Unclip and remove center dash trim panel. (Figure D)
6. Remove (4) screws securing the radio. Unplug and remove the radio. Continue to kit assembly

Line drawing of a car air intake console with control panel and fan (no text or symbols)

(Figure A)

BOTTOM VIEW

(Figure B)

Technical line drawing of a mechanical assembly with no visible text or symbols

(Figure C)

Top-down line drawing of a car dashboard with control panel and air vent (no text or symbols)

(Figure D)

DIN mount radio provision with pocket

1. Slide the DIN cage into the radio housing and secure by bending the metal locking tabs outward. (Figure A)

NOTE: The spacer included in this kit can be used between the radio housing and the DIN cage for vehicles with shallow cavities if necessary. (Figure C)

1. Slide the aftermarket radio into the cage until it snaps into place. (Figure B)
   3 Locate the factory wiring harness in the dash. Metra recommends using the proper mating adapter from Metra or AXXESS. Re-connect the negative battery terminal and test the unit for proper operation.
2. Reassemble dash in reverse order of disassembly.

Aura, Cobalt, G5, HHR, Sky and Vue only: Cut and remove top mounting tabs on each side of the Radio Housing. (Figure D)

Technical line drawing of a mechanical device with ports and mounting brackets (no text or symbols)

(Figure B)

Technical line drawing of a mechanical device with internal components and mounting brackets (no text or symbols)

(Figure C)

Line drawing of a hand using a tool to adjust or install electronic components on a device (no text or symbols visible)

(Figure A)

CUT THE TWO TOP HOLES OFF

(Figure D)

ISO mount radio provision with pocket

1. Mount the ISO Brackets to the radio using the screws supplied with the radio. (Figure A)
2. Slide the radio into the housing until the side clips engage. (Figure B)
3. Locate the factory wiring harness in the dash. Metra recommends using the proper mating adapter from Metra or AXXESS. Re-connect the negative battery terminal and test the unit for proper operation.
4. Snap the trim plate onto the front of the radio housing. (Figure B)

Aura, Cobalt, G5, HHR, Sky and Vue only: Cut and remove top mounting tabs on each side of the Radio Housing. (Figure C)

1. Reassemble dash in reverse order of disassembly.

Line drawing of a hand inserting a screwdriver into a device housing (no text or symbols)

(Figure A)

RIGHT SIDE CLIP

(Figure B)

CUT THE TWO TOP HOLES OFF

(Figure C)

Notes

Notes