99-5832G - Kit voiture Metra - Free user manual and instructions

USER MANUAL 99-5832G Metra

Ford Transit 2015-up

(without 4.2" screen)

99-58326

KIT FEATURES

• ISO DIN radio provision with pocket
• ISO DDIN radio provision
• Radio trim panel is painted gray

Top-down view of a car dashboard with monitor, fan, and ventilation grilles (no visible text or symbols)

KIT COMPONENTS

• A) Radio trim panel • B) Dash panel • C) Radio brackets • D) Pocket • E) Airbag light blank
- F) (4) #8 x 3/8" Phillips truss head screws • G) (2) #8 x 3/8" Phillips pan head screws • H) (3) Metal "U" panel clips
- I) (5) Metal "D" panel clips • J) (4) Small metal "D" panel clips • K) (4) Plastic panel clips

WIRING & ANTENNA CONNECTIONS (sold separately)

Wire harness: • 70-5524 Antenna adapter: • 40-EU10

Table of Contents

Dash Disassembly 2

Kit Preparation....2

Kit Assembly

- ISO DIN radio provision with pocket 3

- ISO DDIN radio provision 3

Final Assembly 3

TOOLS REQUIRED

• Panel removal tool
• Phillips screwdriver
• Socket wrench • T-20 Torx screwdriver

CAUTION! All accessories, switches, climate controls panels, and especially air bag indicator lights must be connected before cycling the ignition. Also, do not remove the factory radio with the key in the on position, or while the vehicle is running.

99-58326

Dash Disassembly Kit Preparation

1. Unclip the dash panel above the radio. (Figure A)
2. Remove (2) T-20 Torx screws securing the factory radio/trim panel. (Figure B)
3. Unclip the factory radio/trim panel from the dash, unplug and remove. (Figure B)
4. Remove (1) T-20 Torx screw per vent then unclip and remove the vents from the factory radio/trim panel. (Figure C)
5. Unclip and remove the hazard switch assembly from the factory radio/trim panel. (Figure D)

Continue to kit preparation

Top-down view of a car dashboard with two directional arrows indicating movement or force (no text or symbols present)

(Figure A) (Figure D) (Figure B) (Figure C)

Interior view of a car dashboard with ventilation grilles and a central vent (no text or symbols visible)

(Figure B)

Mechanical assembly diagram showing two symmetrical components with arrows indicating motion direction (no text or labels)

(Figure C) (Figure A)

Line drawing of a car interior with dashboard and seat (no text or symbols)

1. Secure the factory vents to the radio trim panel using the (2) #8 x 3/8" Phillips pan head screws provided. (Figure A)
2. Snap the factory hazard button into the radio trim panel. An airbag light blank has been included for models without a passenger airbag indicator. (Figure A)

Technical line drawing of a vehicle chassis with handle and seat components (no text or symbols)

Technical line drawing of a car interior frame with no visible text or symbols

1. Attach the (4) plastic panel clips provided, to the radio trim panel. (Figure B)
2. Attach the (12) metal panel clips provided, to the dash panel. (Figure C) Continue to kit assembly

graph TD
    A["Top Floor"] --> B["Left Side"]
    A --> C["Right Side"]
    A --> D["Bottom Side"]
    B --> E["Left Side"]
    C --> F["Right Side"]
    D --> G["Bottom Side"]
    E --> H["Left Side"]
    F --> I["Right Side"]
    G --> J["Bottom Side"]
    H --> K["Left Side"]
    I --> L["Right Side"]
    J --> M["Bottom Side"]

99-58326

Kit Assembly Final Assembly

ISO DIN radio provision with pocket

1. Attach the pocket to the radio brackets using the (4) supplied #8 x 3/8" Phillips truss head screws. (Figure A)
2. Remove the metal DIN sleeve and trim ring from the aftermarket radio.
3. Slide the radio into the completed assembly and then secure it using the screws supplied with the radio. (Figure B)

Continue to final assembly

ISO DDIN radio provision

1. Attach the radio brackets to the radio using screws supplied with the radio. (Figure C)

Continue to final assembly

Technical line drawing of a mechanical assembly with no visible text or symbols

(Figure A)

Technical line drawing of a device casing with mounting feet and internal components (no text or symbols)

(Figure B)

Technical line drawing of a mechanical component with mounting holes and internal structure (no text or symbols)

(Figure C) (Figure A)

1. Cut the shaded portion from the sub-dash of the vehicle to allow the radio to fit. (Figure A)

2. Locate the factory wiring harness and antenna connector in the dash and complete all necessary connections to the radio. Metra recommends using the proper mating adapter from Metra and/or AXXESS. Test the radio for proper operation.

3. Secure the radio into the dash.

4. Snap the radio trim panel over the radio and then reassemble the dash in reverse order of disassembly.

Remove shaded area

INSTALLATION INSTRUCTIONS FOR PART 99-5832G

IMPORTANT

If you are having difficulties with the installation of this product, please call our Tech Support line at 1-800-253-TECH. Before doing so, look over the instructions a second time, and make sure the installation was performed exactly as the instructions are stated. Please have the vehicle apart and ready to perform troubleshooting steps before calling.

KNOWLEDGE IS POWER

Enhance your installation and fabrication skills by enrolling in the most recognized and respected mobile electronics school in our industry. Log onto www.installerinstitute.com or call 800-354-6782 for more information and take steps toward a better tomorrow.

Metra recommends MECP certified technicians