KASMM46G12A - Air-conditioner Kogan - Free user manual and instructions

USER MANUAL KASMM46G12A Kogan

Black adjustable mechanical arm with mounting flange and scroll, mounted on a stand (no text or symbols visible)

FULL MOTION GAS SPRING SINGLE MONITOR MOUNT

(OSTIA SERIES - BLACK)

KASMM46G12A

SAFETY & WARNINGS

Read the entire user guide before you start Installation and assembly. If you have any question regarding any of the instruction or warnings, please contact Kogan.com for assistance.

CAUTION: Usage with products heavier than the rated weights indicated may result in instability causing possible injury.

• Please closely follow the assembly instructions. Improper installation may result in damage or serious personal injury.
• Safety gear and proper tools must be used. This product should only be installed by professionals.
• This product is designed to be installed on solid concrete walls, masonry walls or wood stud walls.
• Make sure that the supporting surface will safely support the combined weight of the equipment and all attached hardware and components.
• Use the mounting screws provided and DO NOT OVER TIGHTEN mounting screws.
• This product contains small Items that could be a choking hazard If swallowed. Keep these items away from children.
• This product is intended for indoor use only. Using this product outdoors could lead to product failure and personal injury.

IMPORTANT: Ensure that you have received all parts according to the component checklist prior to Installation. If any parts are missing or faulty, contact Kogan.com tor a replacement.

MAINTENANCE: Check that the product is secure and safe to use at regular intervals (at least every three months).

VESA Compatible 75x75 100x100

COMPONENTS

	B (x1) C (x1)		D (x3) M6x12	E (x2) F (x1)
A (x1)	G (x1)	H (x1)	I (x1)	J (x1)	K (x1)

M-A (x4)M4x12	M-B (x4)M5x12	M-C (x4)D5

ASSEMBLY

WARNING: Stored energy hazard. Take care when releasing the spring arm.

Step 1:

- Firmly hold the two halves of the spring arm together and have another person cut off the cable tie from around the spring arm.

- Slowly release the pressure on the spring arm and allow it to gradually stretch to its full extension.

Technical illustration showing a robotic arm being adjusted to form a mechanical component (no text or symbols present)

Step 2:

Step 3:

✓ ! ✓ ✗ Too long Too Short

M-A M-B M-C 3mm TOP K

Technical diagram showing mechanical assembly with labeled components M-A, M-B, and M-C, including directional arrows indicating motion or flow.

Step 4:

To properly balance the arm with monitors mounted, adjust the spring tension using the supplied Allen Key as follows:

Technical line drawing of a mechanical device with hands operating it, showing rotational motion and directional arrows (no text or symbols)

Position and firmly hold the arm horizontally as shown. Ask for assistance should you require it.

Three-step diagram showing mechanical assembly states with checkmark indicators, indicating absence or rejection.

CAUTION: To avoid damage to monitors or mount, always keep the arm in a horizontal position while adjusting. Again, ask for assistance if required.

	If the arm drops, turn the adjustment screw counterclockwise until it stays in a horizontal position
	If the arm rises, turn the adjustment screw clockwise until it stays in a horizontal position.

Step 5:

Technical line drawing of a mechanical arm assembly with no visible text or symbols

CAUTION: Do not overtighten any of the screws used to assemble or adjust the mount.

Step 6:

Note: Adjust to the desired angle then tighten the screws using the Allen key as shown, alternating from each screw as you tighten them.

NOTES

Need more information?

We hope that this user guide has given you

the assistance needed for a simple set-up.

For the most up-to-date guide for your product, as well as any additional assistance you may require, head online to help.kogan.com

kōgan