99-9107B - Kit voiture Metra - Free user manual and instructions

USER MANUAL 99-9107B Metra

INSTALLATION INSTRUCTIONS FOR PART 99-9107B

APPLICATIONS

Audi A4 / S4

2002-2008

(With Symphony Radio)

99-9107B

KIT FEATURES

• DIN Head Unit Provision with Pocket
• ISO DIN Head Unit Provision with Pocket
• Double DIN Head Unit Provision
• Painted Matte Black to Match Factory

Control panel display showing a digital interface with multiple ports and a numeric keypad, likely for industrial or automotive monitoring.

KIT COMPONENTS

WIRING AND ANTENNA CONNECTIONS (Sold Separately) Harness:

• 70-1787 - VW / Audi Harness 1993-up

Antenna Adapter:

• 40-VW10 - Euro Antenna Adapter 1986-up

TOOLS REQUIRED:

• (2) 86-9001 Head Unit Removal Tools • Small Flat Blade Screwdriver • Phillips Screwdriver

1-800-221-0932

www.metraonline.com

© COPYRIGHT 2004-09 METRA ELECTRONICS CORPORATION

TABLE OF CONTENTS

Dash Disassembly

- Audi A4 / S4 2002-2008 w/Symphony Radio ..... 1

Kit Assembly

• DIN Head Unit Provision with Pocket 2
• ISO DIN Head Unit Provision with Pocket .... 3
• Double DIN Head Unit Provision .... 4

Final Assembly 5

KNOWLEDGE IS POWER

Enhance your installation and fabrication skills by enrolling in the most recognized and respected mobile electronics school in our industry. Log onto www.installerinstitute.com or call 800-354-6782 for more information and take steps toward a better tomorrow.

Metra recommends MECP certified technicians..

AUDI A4 / 54 2002-2008 W/SYMPHONY RADIO

1 Disconnect the negative battery terminal to prevent an accidental short circuit.
2 Insert Metra's 86-9001 into the slots in the factory head unit and pull the unit out. (Figure A)
3 Disconnect the wiring.

A CO B1 L100 D K F14 FAR BAT TANT HAT/3 L100 HAT/3 TANT TANT

DIN HEAD UNIT PROVISION WITH POCKET

1 Snap the DIN cage into the Radio Housing and secure by bending the metal locking tabs down. (Figure A)
2 Locate the factory wiring harness in the dash. Metra recommends using the proper mating adapter from Metra or AXXESS. Re-connect the negative battery terminal and test the unit for proper operation.
3 Snap radio assembly into factory radio opening.
4 Slide the aftermarket radio into the cage and secure. (Figure B)
5 Snap the pocket into the Radio Housing until secure. (Figure C)

NOTE: Once the dash kit is snapped in, it cannot be removed without dash panel removal

Illustration of a hand using a tool to adjust or install electronic components on a device (no text or symbols visible)

Technical line drawing of a device chassis with labeled ports and connectors (no text or symbols)

Line drawing of a computer drive unit with labeled ports and control panel (no text or symbols)

ISO DIN HEAD UNIT PROVISION

1 Mount the ISO Brackets to the head unit with the screws supplied with the unit. (Figure A)
2 Slide the head unit into the radio opening until the slide clips engage. (Figure B)
3 Snap the ISO Trim Plate into the Radio Housing. (Figure B)
4 Snap the pocket into the Radio Housing. (Figure C)
5 Locate the factory wiring harness in the dash. Metra recommends using the proper mating adapter from Metra or AXXESS. Re-connect the negative battery terminal and test the unit for proper operation.
6 Snap the radio assembly into the factory radio opening.

NOTE: Once the dash kit is snapped in, it cannot be removed without dash panel removal

Line drawing of a hand using a screwdriver to adjust or install a device into a rectangular box (no text or symbols)

Technical line drawing of a mechanical device with directional arrows indicating movement or force (no text or symbols present)

Technical line drawing of a device with an open lid and two arrows indicating movement or force (no text or symbols present)

DOUBLE DIN HEAD UNIT PROVISION

1 Cut and remove center divider from radio housing. (Figure A)
2 Snap the DDIN brackets to the inside edge of the radio housing. (Figure B)
3 Slide the DDIN radio unit into the DDIN bracket/radio housing assembly and secure the unit to the kit using the screws supplied with the head unit. (Figure C)
4 Snap the DDIN trim-plate onto the housing/radio assembly. (Figure C)
5 Locate the factory wiring harness in the dash. Metra recommends using the proper mating adapter from Metra or AXXESS. Re-connect the negative battery terminal and test the unit for proper operation.
6 Snap radio assembly into factory radio opening.

NOTE: Once the dash kit is snapped in, it cannot be removed without dash panel removal

Line drawing of a hand using a tool to adjust or install a mechanical component (no text or symbols present)

Technical line drawing of a mechanical housing or bracket component (no text or symbols)

Technical diagram of an electronic device showing internal components and directional arrows (no text or symbols)

NOTES

99-9107B INSTRUCTIONS