R113-X30 - Server GIGABYTE - Free user manual and instructions

USER MANUAL R113-X30 GIGABYTE

© 2023 Giga Computing Technology CO., LTD. All rights reserved.

The trademarks mentioned in this manual are legally registered to their respective owners.

Disclaimer

Information in this manual is protected by copyright laws and is the property of Giga Computing. Changes to the specifications and features in this manual may be made by Giga Computing without prior notice. No part of this manual may be reproduced, copied, translated, transmitted, or published in any form or by any means without Giga Computing's prior written permission.

Documentation Classifications

In order to assist in the use of this product, Giga Computing provides the following types of documentation:

■ User Manual: detailed information & steps about the installation, configuration and use of this product (e.g. motherboard, server barebones), covering hardware and BIOS.
■ User Guide: detailed information about the installation & use of an add-on hardware or software component (e.g. BMC firmware, rail-kit) compatible with this product.
■ Quick Installation Guide: a short guide with visual diagrams that you can reference easily for installation purposes of this product (e.g. motherboard, server barebones).

Please see the support section of the online product page to check the current availability of these documents.

For More Information

For related product specifications, the latest firmware and software, and other information please visit our website at http://www.gigabyte.com/Enterprise

For GIGABYTE distributors and resellers, additional sales & marketing materials are available from our reseller portal: http://reseller.b2b.gigabyte.com

For further technical assistance, please contact your GIGABYTE representative or visit https://esupport.gigabyte.com/ to create a new support ticket

For any general sales or marketing enquiries, you may also message GIGABYTE server directly by email: [e-mail]

Table of Contents

Chapter 1 Getting Started....5

1-1 Software Requirement .... 5

1-2 Gigabyte Management Console Network Configuration 6

1-3 Log In Gigabyte Management Console....7

1-3-1 Required Browser Settings: 8

1-4 Quick Button and Logged-in User 9

1-5 Help....10

1-6 Menu Bar.... 10

Chapter 2 Enter Gigabyte Management Console....11

2-1 Dashboard.... 11

2-2 Sensor....12

2-2-1 Sensor Detail....13

2-2-2 Sensor Events....14

2-3 System Inventory 15

2-3-1 CPU Inventory 15

2-3-2 DIMM Inventory 16

2-3-3 PCI Inventory....17

2-3-4 HDD Inventory....18

2-3-5 NIC Inventory....19

2-3-6 GPU Inventory....20

2-4 FRU Information....21

2-5 Logs & Reports 23

2-5-1 IPMI Event Log 23

2-5-2 Audit Log 25

2-5-3 Video Log 26

2-5-4 SOL Video Log 26

2-6 Settings 27

2-6-1 Captured BSOD....27

2-6-2 Date & Time....28

2-6-3 External User Services....29

2-6-4 KVM Mouse Settings....39

2-6-5 Log Settings....40

2-6-6 Manage Licenses 43

2-6-7 Media Redirection Settings....43

2-6-8 Network Settings 48

2-6-9 PAM Order Settings....56

2-6-10 Platform Event Filter....57

2-6-11 Services....65
2-6-12 SMTP Settings....69
2-6-13 SSL Settings....72
2-6-14 System Firewall 77
2-6-15 User Management....85
2-6-16 Video Recording....89
2-6-17 Fan Profile 97
2-6-18 Power Consumption....99
2-6-19 IMPI Interfaces 100
2-6-20 RAID Management....101

2-7 Remote Control.... 112

2-8 Images Redirection.... 118

2-8-1 Remote Media 119

2-9 Power Control 120

2-10 Maintenance Group.... 121

2-10-1 Backup Configuration....122
2-10-2 Firmware Image Location....123
2-10-3 Firmware Information....124
2-10-4 Firmware Update....125
2-10-5 Preserve Configuration....130
2-10-6 Restore Configuration....134
2-10-7 Restore Factory Defaults....135
2-10-8 System Administrator....136
2-10-9 Sign Out....137

Chapter 1 Getting Started

1-1 Software Requirement

• Client machine with 8GB RAM.
• If the client machine has 4GB RAM, there will be lag in video/keyboard/mouse functionality.

Supported Browsers

• Chrome latest version.
• IE 11 and above.
• Firefox (with limited support).

Note: It is advisable to use Chrome or IE for H5Viewer since Firefox has its own memory limitations.

1-2 Gigabyte Management Console Network Configuration

Follow the instruction to enable the console redirection function.

1. You can gather the IP address on the POST screen.

GIGABYTE™ BMC IP : 10.1.6.113 Press or to enter Setup, to POST, Display Boot Menu, to Network PXE Boot

1. Or, Go to BIOS setup menu.
2. Select Server Management.
3. Select BMC network Configuration.
4. Define Configuration Address source to DynamicBmcDhcp or Static.
5. Save and Exit.
6. The BMC IP Address will appear on the Station IP address parameter.

Optio Setup - ANI Server Mount --BNC network configuration-- LAN channel 1 Configuration Address source [Dynomucine@http] Station IP address 10.1.7.191 Subnet mask 255.255.255.0 Router IP address 10.1.7.253 Station MAC address 18-05-40-05-24-06 Real-time get BNC network address Select to configure LNV channel parameters statically or dynomucaly(by BNT or BMC). Unspecified option will not modify any BNC network parameters during BIOS phase +: Select Screen PA: Select item. Enter: Select +/- Change Opt. PI: General help FD: Previous Values P5: Options/Default P10: Save A Fail EWS: Exit

1. Save the configuration and exit BIOS setup menu.

1-3 Log In Gigabyte Management Console

To access the Gigabyte Management Console, the MegaRAC utility will prompt you to enter the User Name and Password.

MEGARAC SP-X Username Password US - English Remember Username Sign me in

I forgot my password

The fields are explained as follows:

For basic login to the MegaRAC UI, use the following login:

• Username: admin
• Password: Refer to unique MB serial number.
  • US - English: Changes the interface language.

NOTE!

If your motherboard / server version is older than G9 (upgrade version), then use the following login:

Username: admin

Password: password

This serial number can be found on the serial number sticker located on the motherboard of every GIGABYTE server motherboard and system. The unique pre-programmed password will be the last 11 characters of the serial number. For example, for the below serial number, the password will be "JG4P6400027

1/A/JG4P64 00027

GIGABYTE will also affix new stickers that display the unique BMC password (example below) to both the product box (packaging) and to the CPU cover (for motherboards sold separately) or the server chassis.

Unique BMC Password JG4P6400027

Please see the reference guide below / attached for where to find locations of this sticker according to product / model type.

Products that have been implemented with this change will be indicated as version G9 on the "Upgrade Version" sticker located on the motherboard / motherboard anti-static packaging / server chassis / server packaging.

UPG VER: G□1 G□2 G□3 G□4 G□5 G□6 G□7 G□8 G□9 G□10+

Remember Username: Check this option to remember your login credentials.

Sign me in: After entering the required credentials, click the Sign me in to login to GUI.

I forgot my password: If you forget your password, you can generate a new one using this link. Enter the user name, click on Forgot Password link. This will send the newly generated password to the configured Email-ID for the user.

1-3-1 Required Browser Settings:

Allow file download from this site: For Internet Explorer, Choose Tools ->Internet Options ->Security Tab, based on device setup, select among Internet, Local intranet, trusted sites and restricted sites. Click Custom level.... In the Security Settings - Zone dialog opened, under settings, find Downloads option, Enable File download option. Click OK to the entire dialog boxes.

For all Other Browsers, accept file download when prompted.

Enable javascript for this site: The icon indicates whether the javascript setting is enabled in browser.

Enable cookies for this site: The icon indicates whether the cookies setting are enabled in browser.

Cookies must be enabled in order to access the website.

1-4 Quick Button and Logged-in User

The user information and quick buttons are located at the top right of the Web GUI. A screenshot of the logged-in user information is shown below.

US - English

Sync

Refresh

admin ▼

User Information

The logged-in user information shows the logged-in user, his/her privilege and the four quick buttons allowing you to perform the following functions:

Logged-in user and its privilege level

This option shows the logged-in user name and privilege. There are five kinds of privileges.

User: Only valid commands are allowed.

Operator: All BMC commands are allowed except for the configuration commands that can change the behavior of the out-of-hand interfaces.

Administrator: All BMC commands are allowed.

No Access: Login access denied.

OEM: All OEM commands are allowed.

Refresh: Click the icon to reload the current page.

Sync: Click the icon to synchronize with Latest Sensor and Event Log updates.

US - English: Click to select the language of the Web GUI.

Warning: Click to view the warning messages.

Notification: Click the icon to view the notification messages.

1-5 Help

Help - The Help icon (?) is Located at the top right of the each page in Web GUI. Click this help icon to view more detailed field descriptions.

1-6 Menu Bar

The menu bar displays the following:

MEGARAC SP-X 13.01.28 Jul 9 2021 06:19:35 UTC Host Online Quick Links.. Dashboard Sensor System Inventory > FRU Information Logs & Reports > Settings Remote Control Image Redirection Power Control Maintenance Sign out

Chapter 2 Enter Gigabyte Management Console

2-1 Dashboard

The Dashboard page gives the overall information about the status of a device.

To open the Dashboard page, click Dashboard from the menu bar. It displays the following:

Dashboard

A brief description of the Dashboard page is given below.

Product Information

Displays the technical information for the system.

Power Consumption

Displays the current power consumption information.

Network Information

Displays the network information of the system.

BMC System Information

Displays the system BMC information of the system.

System Inventory Information

Displays the system inventory information of the system.

IPMI Event Log

Displays the list of event logs occurred by the different sensors on this system.

2-2 Sensor

The Sensor Readings page displays all the sensor related information.

To open the Sensor Readings page, click Sensor from the menu. Click on any sensor to show more information about that particular sensor, including thresholds and a graphical representation of all associated events.

A sample screenshot of Sensor Readings page is shown below.

MEGARIC SP-X SUSIL NEW INJEMERSON &C New Online Quick Links... Dashboard Sensor Analysis inventory File information Logic & Impacts Settings Network Control Image/Redirections Power Control Maintenance Big set Sensor Reading: User reading all sensors Critical Sensors (0) All threshold sensors are normal Discrete Sensor States (6) Sensor Name State + CPU Status: Processor Preference Detected + CPU Status: Processor Preference Detected + PSL Status: Processor Detection + PSL Status: Processor Detection, Power Supply Input Load (A1/B2) SEL No state defined + Working No state defined Normal Sensors (H) Sensor Name Reading Behavior + BPS/NAR_3A 2000.00 fps + BPS/NAR_3B 2400.00 fps + BPS/NAR_3A 12000.00 fps

The Sensor Readings page contains the following information:

In this Sensor Reading page, Live readings for all the available sensors with details like Sensor Name, Status, Current Reading and Behavior will be appeared, else you can choose the sensor type that you want to display from the list. Some examples for sensors are Temperature Sensors, Fan Sensors, Watchdog Sensors and Voltage Sensors etc.

Note: Four DIMM Temp sensors are deployed for monitoring the DIMM temperature on the system. Users must take notice that the live reading of each DIMM Temp sensor indicates the temperature of a DIMM group, not the temperature of a specific DIMM.

Note: Four DIMM Temp sensors are deployed for monitoring the DIMM temperature on system. Users must take notice that the live reading of each DIMM Temp sensor indicates the temperature of a DIMM group, not the temperature of a specific DIMM.

2-2-1 Sensor Detail

Select a particular sensor from the Critical Sensor or Normal Sensor lists. The Sensor Information as Live Widget and Thresholds for the selected sensor will be displayed as shown below.

Note: For Illustrative Purpose, a sample screenshot of Sensor detail page with Change thresholds option is shown and explained below.

Note: Widgets are little gadgets, which provide real time information about a particular sensor. User can track a sensor's behavior over a specific amount of time at specific intervals. The result will be displayed as a line graph in the widget. The session will not expire, until the widgets gets a live data of the last widget that is kept opened.

For the selected sensor, this widget gives a dynamic representation of the readings for the sensor.

There are six types of thresholds:

• Lower Non-Recoverable (LNR)
- Lower Critical (LC)
• Lower Non-Critical (LNC)
• Upper Non-Recoverable (UNR)
• Upper Critical (UC)
• Upper Non-Critical (UNC)

The threshold states could be Lower Non-critical - going low, Lower Non-critical - going high, Lower Critical - going low, Lower Critical - going high, Lower Non-recoverable - going low, Lower Non-recoverable - going high, Upper Non-critical - going low, Upper Non-critical - going high, Upper Critical - going low, Upper Critical - going high, Upper Non-recoverable - going low, Upper Non-recoverable - going high.

A graphical view of these events (Number of Entries vs. Thresholds) can be viewed as shown in the Sensor Readings page screenshot.

2-2-2 Sensor Events

The Sensor Events page displays information about events that have triggered the system's sensor. A sample screenshot of Sensor Events page is shown below.

Sensor Events
unlaided use
ID: 60 unknown sensor of type platform_security logged a bias: oem timestamped was discounted	16 days ago
ID: 79 unknown sensor of type platform_security logged a bias: oem timestamped was discounted	2 days ago
ID: 74 unknown sensor of type platform_security logged a bias: oem timestamped was discounted	3 days ago
ID: 71 unknown sensor of type platform_security logged a bias: oem timestamped was discounted	4 days ago
ID: 76 unknown sensor of type platform_security logged a bias: oem timestamped was discounted	5 days ago
ID: 54 unknown sensor of type platform_security logged a bias: oem timestamped was discounted	6 days ago
ID: 73 unknown sensor of type platform_security logged a bias: oem timestamped was discounted	7 days ago
ID: 72 unknown sensor of type platform_security logged a bias: oem timestamped was discounted	8 days ago
ID: 71 unknown sensor of type platform_security logged a bias: oem timestamped was discounted	9 days ago
ID: 23 HDMI sensor of type drive Island logged a EPB Virtual Management Controller Event: Drive Presence was answered	10 days ago
ID: 18 HDMI sensor of type drive Island logged a EPB Virtual Management Controller Event: Drive Presence was answered	11 days ago

2-3 System Inventory

The System Inventory page displays the following information:

• CPU Inventory
• DIMM Inventory
• PCI Inventory
• HDD Inventory
• NIC Inventory
• GPU Inventory

A screenshot displaying the menu items under System Inventory is shown below.

System Inventory » CPU Inventory » DIMM Inventory » PCI Inventory » HDD Inventory » NIC Inventory » GPU Inventory

A detailed description of System Inventory is given below.

2-3-1 CPU Inventory

This page displays all detected CPUs on this device. Select one CPU to see the details of that entry. Click Download SMBIOS file to download the SMBIOS file.

MegaRVC SP-X 12:00 AM 23:00:00 PM Avg 23:00:00 PM Log trading Quick links... Outboard Server System Inventory CPU Inventory Data Inventory FPU Inventory FCD Inventory VDC Inventory SPX Information Logic & Resources Settings Remote Control Usage/Description Power Control Maintenance Sign out CPU Inventory Lastifier Name Manufacturing Family External Clock Miss Speed Spend Hindi M4D Eng Sample: 188-655880000 US_F Advanced Home Devices Inc. Dev 100,000 Mbps 5,000 GHz 4,000 GHz Advanced Software Solutions

2-3-2 DIMM Inventory

This page displays all detected DIMMs on this device. It allows you to see memory attributes, individual memory details. Click Download SMBIOS file to download the SMBIOS file.

MegaRAC SP-X E:\2023-08-15\UNI2234\JYCH-000000001\NT DIMM Inventory Memory Attributes Maximum Capacity Installed Capacity Sites Available Sites Used Center Connections 236 GB $1 GB 4 1 None Individual Memory Details Location Manufacturer Manufacturer Port Number Site Location Type Size Speed DAIR_PB_AI Emerson CTS460485L/ANA 172903A DORS 0.50 AEB Recommended Options

2-3-3 PCI Inventory

This page displays all detected PCI cards on this device. It allows you to see on-board PCI cards, add-on PCI cards. Click Download SMBIOS file to download the SMBIOS file.

PCI Inventory On Board Type Name Manufacturer Number ID Devio ID Link Mutors Link Speed Internet capacitor Internet capacitor X710 for 2008069-7 Intel Corporation Deli 300000 Deli 300000 Deli 300000 Deli 300000 Deli 300000 Deli 300000 Deli 300000 Deli 300000 Deli 300000 Deli 300000 Deli 300000 Deli 300000 Internet capacitor Internet capacitor X710 for 2008069-7 Intel Corporation Deli 300000 Deli 300000 Deli 300000 Deli 300000 Deli 300000 Deli 300000 Deli 300000 PCI in Stage ESPRESS TECHNOLOGY, INC. Deli 3455 Deli 3455 Deli 3455 Deli 3455 Deli 3455 Deli 3455 Deli 3455 Deli 3455 VOC system component: ESPRESS Technologies, Inc. Deli 3455 Deli 3455 Deli 3455 Deli 3455 Deli 3455 Deli 3455 Add In Card no information for PCI is cast

2-3-4 HDD Inventory

This page displays all detected HDDs on this device. It allows you to see on-board HDDs, add-on HDDs. Click Download SMBIOS file to download the SMBIOS file.

MegaRMC SPX COLOR AUCO RESOURCES © Host Edition Quick Links... Backboard Sensor Cycleware Inventory CPU Networking DSRAM Inventory PCI Inventory HDD Inventory HDC Inventory CPU Networking FBU Information Logic & Requests Settings Remote Control Image Interconnects Power Control Maintenance sign out HDD Inventory On Board DAC/HR Type Name Manufacturer Emissions Version Sedal/Number Size Sugar PCS RTEL EXERCICUMMS total 400 CVCOSKOSICS/SPXN 90.2-58 Add In Card new information for 400 in card

2-3-5 NIC Inventory

This page displays all detected NICs on this device. It allows you to on-board NICs, add-on NICs. Click Download SMBIOS file to download the SMBIOS file.

MepRAC SPX C:\COLOR\ALLS\POST KONIONE.VI.Y. Quick Links... Installboard Sensor Systems Inventory CPU Inventory ECON Inventory PC Inventory HDD Inventory MIC Inventory GPU Inventory FPU Information Logic & Project Settings Remote Control Image/Reductance Power Control Maintenance Sign out NIC Inventory On Board Add In Card New information for iMC in card.

2-3-6 GPU Inventory

This page displays all detected GPU cards on this device. It allows you to see on-board GPU cards, add-on PCI cards. Click Download SMBIOS file to download the SMBIOS file.

MegaRAC SP-X 11:05:00 August 2018 SAPR/CSPX Next Update Quick Cards... Dashboard Server Systems Inventory CPU Inventory DRIP Inventory FCD Inventory FDD Inventory ADC Inventory EPC Inventory FPU Information Logic & Resources Settings Remote Control Usage/ControlBox Power Control Maintenance Sign-up GPU Inventory Add In Card Add In Card for IPTC in card GPU Information Only include IPTC cards are supported, but the HSS AUSB to CPU is not included.

2-4 FRU Information

FRU Information page displays the BMC's FRU device information. FRU page shows information like Basic Information, Chassis Information, Board Information and Product Information of the FRU device.

To open the FRU Information page, click FRU Information from the menu bar. Select a FRU Device ID from the FRU Information section to view the details of the selected device. A screenshot of FRU Information page is shown below.

NEGARAC SP-X 2021-07-28 16:28:22 [JYFZ-00080508F] FRU Yield Preplicable Units Available FRU Devices FRU Device ID: FRU Device Name: BAC_FRU Chassis Information Board Information Board Information Area Format Version 1 Language 0 Product information Area Format Version 1 Language 0 Chassis Type Rack Mount Chassis Manufacture Date Time Fri Jan 19/03/2021 Board Manufacturer SISABYTE Product Name RSD-HA2-00 Chassis Part Number 01324667 Board Product Name HRBQ-FS1-00 Board Serial Number UZSP1288825 Board Part Number 12943678548 FRU File ID Board Eku3a NULU Product information Product information Area Format Version 1 Language 0 Product Manufacturer SISABYTE Product Name RSD-HA2-00 Product Part Number 08890860001 Product Hension QUS Product Serial Number SLHPRD32P0833 Rout Tag 02316M YMBI 12316M78948 FRU File ID PlaceEku3a

The following fields are displayed here for the selected device:

Available FRU Devices

• FRU device ID - Select the device ID from the drop down list
• FRU Device Name - The device name of the selected FRU device.

Chassis Information

• Chassis Information Area Format Version
• Chassis Type
• Chassis Part Number
• Chassis Serial Number
• Chassis Extra

Board Information

• Board Information Area Format Version
- Language
• Manufacture Date Time
- Board Manufacturer
- Board Product Name
- Board Serial Number
- Board Part Number
- FRU File ID
- Board Extra

Product Information

• Product Information Area Format Version
- Language
• Product Manufacturer
- Product Name
• Product Part Number
- Product Version
• Product Serial Number
- Asset Tag
- FRU File ID
- Product Extra

2-5 Logs & Reports

The Logs & Reports page displays the following information:

• IPMI Event Log
• Audit Log
• Video Log

A screenshot displaying the menu items under Logs & Reports is shown below.

Logs & Reports » IPMI Event Log » Audit Log » Video Log » SOL Video Log

A detailed description of Logs & Reports is given below.

2-5-1 IPMI Event Log

This page displays the list of event logs occurred by the different sensors on this device. Double click on a record to see the details of that entry. You can use the sensor type or sensor name filter options to view those specific events or you can also sort the list of entries by clicking on any of the column headers.

To open the Event Log page, click Logs & Reports > IPMI Event Log from the menu bar. A sample screenshot of Event Log page is shown below.

MegaWMC SP-X 12.04.05 June 28, 2022 Linked Web URL: SP-X SP-X-1112.2029 Signal Events Event Log All System Work Log Filter by Date: 2019-07-03 00:00 2023-07-16 15:00 Filter by Type: All Events All Events All Settings Page 1 © July 2023 Log Downloaded Booklog July 2023 ID: TL 05/ST/M Event sensor of type System Event logged a Site : OEM System Book Event was asserted Thursday, July 2023, 2:30:00 pm ID: Rs BMC Event sensor of type Power Unit logged a BMC Event : Power Off / Power Down was asserted Tuesday, July 2023, 2:30:00 pm ID: Rs BMC Event sensor of type Power Unit logged a BMC Event : Power Off / Power Down was asserted Tuesday, July 2023, 2:30:00 pm ID: Rs SYSTEM Event sensor of type System Event logged a Site : Timestamp Clock switch was asserted Tuesday, July 2023, 2:31:39 pm ID: 67 BMC Event sensor of type System Event logged a BMC Event : Timestamp Clock switch was asserted Tuesday, July 2023, 2:41:49 pm ID: Rs BMC Event sensor of type System Excretraped a BMC Event : Timestamp Clock switch was asserted Wednesday, July 2023, 4:40:00 pm

The Event Log page consists of the following fields:

Filter By Date: Filtering can be done by selecting Start Date and End Date.

Filter By Type: The category could be either All Events, System Event Records, OEM Event Records, BIOS Generated Events, SMI Handler Events, System Management Software Events, System Software - OEM Events, Remote Console software Events, Terminal Mode Remote Console software Events.

Note: Once the Filter By Date and Filter type are selected, the list of events will be displayed with the Event ID, Time Stamp, Sensor Type, Sensor Name and Description.

Event Log Statistics: Displays the statistical graph for the selected date.

Clear Event Logs: Deletes all the event logs.

Download Event Logs: Downloads the event logs.

Procedure

1. From the Filter By Date field, select the time period by Start Date and End Date using Calendar for the event categories.
2. From the Filter By Type field, select the Type of the event and Sensor name to view the events for the date. The events will be displayed based on the selected time period.
3. To clear all events from the list, click Clear All Event Logs.
4. To download the event logs, click Download Event Logs.

2-5-2 Audit Log

To open the Audit Log page, click Logs & Reports > Audit Log from the menu bar. A sample screenshot of Video Log page is shown below.

Note: For configuration, go to Settings > Log Settings > Advanced Log Settings.

Audit Log Filter by time: 2015-02-18 00:00 2023-02-18 00:00 Audit Log Edit User ID: 191.2023-01-20 22:15:25 (UTC+00:00 GMT) AM745DC857NC5 spx_reservice.spx_reservice-- (2040 : 2640 IP/RO)https Login from IP30.1.2.85 useradmin- ID: 189.3023-01-20 22:05:43 (UTC+00:00 GMT) AM745DC857NC5 spx_reservice.spx_reservice-- (2040 : 2640 IP/RO)https Login from IP30.1.2.85 useradmin- ID: 157.2023-01-20 23:08:16 (UTC+00:00 GMT) AM745DC857NC5 spx_reservice.spx_reservice-- (2040 : 2640 IP/RO)https Login from IP30.1.16.167 useradmin- ID: 154.2023-01-20 23:08:16 (UTC+00:00 GMT) AM745DC857NC5 spx_reservice.spx_reservice-- (2040 : 2640 IP/RO)HTTPS logust from IP38.1.16.167 useradmin- ID: 153.2023-01-20 23:08:16 (UTC+00:00 GMT) AM745DC857NC5 spx_reservice.spx_reservice-- (2040 : 2640 IP/RO)HTTPS logust from IP38.1.16.167 useradmin- ID: 154.2023-01-20 23:41:49 (UTC+00:00 GMT) AM745DC857NC5 spx_reservice.spx_reservice-- (2040 : 2640 IP/RO)https Login from IP30.1.16.167 useradmin- ID: 151.2023-01-29 23:07:19 (UTC+00:00 GMT) AM745DC857NC5 spx_reservice.spx_reservice-- (2040 : 2640 IP/RO)https Login from IP30.1.16.167 useradmin- ID: 154.2023-01-29 23:07:29 (UTC+00:00 GMT) AM745DC857NC5 spx_reservice.spx_reservice-- (2040 : 2640 IP/RO)HTTPS logust from IP38.1.16.167 useradmin- ID: 155.2023-01-29 23:07:39 (UTC+00:00 GMT) AM745DC857NC5 spx_reservice.spx_reservice-- (2040 : 2640 IP/RO)HTTPS logust from IP38.1.16.167 useradmin- ID: 151.2023-01-33 23:35:42 (UTC+00:00 GMT) AM745DC857NC5 spx_reservice.spx_reservice-- (2040 : 2640 IP/RO)https Login from IP30.1.16.167 useradmin- ID: 152.2023-01-33 23:35:42 (UTC+00:00 GMT) AM745DC857NC5 spx_reservice.spx_reservice-- (2040 : 2640 IP/RO)HTTPS logust from IP38.1.16.167 useradmin- ID: 149.3023-01-34 23:34:12 (UTC+00:00 GMT) AM745DC857NC5 spx_reservice.spx_reservice-- (2040 : 2640 IP/RO)https Login from IP30.1.16.167 useradmin- ID: 169.3023-01-34 23:34:12 (UTC+00:00 GMT) AM745DC857NC5 spx_reservice.spx_reservice-- (2040 : 2640 IP/RO)HTTPS logust from IP38.1.16.167 useradmin- ID: 147.2023-01-37 23:34:19 (UTC+00:00 GMT) AM745DC857NC5 spx_reservice.spx_reservice-- (2040 : 2640 IP/RO)https Login from IP38.1.16.167 useradmin- ID: 149.3023-01-37 23:34:19 (UTC+00:00 GMT) AM745DC857NC5 spx_reservice.spx_reservice-- (2040 : 2640 IP/RO)HTTPS logust from IP38.1.16.167 useradmin- ID: 149.3023-01-38 23:36:19 (UTC+00:00 GMT) AM745DC857NC5 spx_reservice.spx_reservice-- (2040 : 2640 IP/RO)https Login from IP38.1.16.167 useradmin- ID: 149.3023-01-39 23:36:29 (UTC+00:00 GMT) AM745DC857NC5 spx_reservice.spx_reservice-- (2040 : 2640 IP/RO)HTTPS logust from IP38.1.16.167 useradmin- ID: 149.3023-01-39 23:36:39 (UTC+00:00 GMT) AM745DC857NC5 spx_reservice.spx_reservice-- (2040 : 264OIP/RO)https Login from IP38.1.16.167 useradmin- ID: 149.3D-CL-CL-CL-CL-CL-CL-CL-CL-CL-CL-CL-CL-CL-CL-CL-CL-CL-CL-CL-CL-CL-CL-CL-CL-CL-CL-CL-CL-CL-CL-CL-CL-CL-CL-CL-CL-CL-CL-CL-CL-CL-CL-CL-CL-CL-CL-CL-CL-CL-CL-

The Audit Log page consists of the following fields:

Filter By Date: Filtering can be done by selecting Start Date and End Date.

Download Logs: Allows you to download the audit logs.

Procedure

1. From the Filter By Date field, select the time period by Start Date and End Date using Calendar for the event categories.
2. To download the event logs, click Download Logs.

2-5-3 Video Log

To open the Video Log page, click Logs & Reports > Video Log from the menu bar.

A sample screenshot of Video Log page is shown below.

Note: Video Trigger Settings should be enabled, to display the Video Log page. Video Trigger Settings can be configured under Settings > Video Recording > Auto Video Settings > Video Trigger Settings.

MogulUC SP3-X 21.06.38 and 1 MIGUULUC SPORT To: Real Digital Copyrights Background Language systema inventory New information logis to target XML content log Autograph Video Log WBS Video Log Settings Website Content Image浏览器 Power Control Maintenance Tags list Video Log All video event logs Follow by Date: 2025.04.20 03:00:00 2025.04.20 03:00:00 Page 1 Event Log (10:00-15)

Video will be allowed to play/download only if file size is lesser than 40MB. Browsers have various memory restrictions, due to this browser cannot store and process data greater than 40MB (approximately). If file size is greater than 40MB, user will be notified with a message to use Java player Application.

2-5-4 SOL Video Log

To open the SOL Video Log page, click Logs & Reports > SOL Video Log from the menu bar. A sample screenshot of SOL Video Log page is shown below.

Note: Video Trigger Settings should be enabled, to display the SOL Video Log page. Video Trigger Settings can be configured under Settings > Video Recording >SOL Video Settings > SOL Video Trigger Settings.

MogulUAC S&P X 13.05.20 Job 1: INSTRATATE SOURCE

Book/Video

SOL Video log - All SOL Video log LOG - English SOS Save Refresh admin - Book/Book Language Systems Inventory News Information Logic & Reports www.csc.org • Applicator Video Log SQL Video Log Settings Interactive Control Image Destination User Control Editorial Signed

2-6 Settings

This group of pages allows you to access various configuration settings. A screenshot of Configuration Group menu is shown below.

NEGARIC SP-X ISSUE 28 NEW COLDING WORK Host Online Open Links... Clearboard Sensor System inventory FPU information Log & Reports Settings Remote Control Image Reflective Power Controls Maintenance Sign out Settings Configure EMC users Capture Tools Data & Time Industrial User Services Web User Setting Log Settings Manage License Media Radio/Style Settings Network Settings PWM Order Settings Platform Devt Filter Servers SMTP Settings Alt. Settings System Wizard User Management Video Recording Fan Profile Power Coverage PWM Interface

A detailed description of the Settings menu is given below.

2-6-1 Captured BSOD

This menu is used to display a snapshot of the blue screen captured at the time when/if the host system crashed since the last reboot. A sample screenshot of Captured BSOD is shown below.

Note: KVM service should be enabled to display the BSOD. This can be configured under Settings > Services > KVM.

NEGARAC SP-X COSL30 AVR 2.001.0000.0000 • Next Online Check Loss... Default Server System Inventory File Information Logs & Requests Settings Remote Control Image/Internetline Power Control Maintenance Sign out Captured BSOD Last BSOD Screen Captured BSOD Screen is not available.

2-6-2 Date & Time

This field is used to set the date and time on the BMC. A sample screenshot of Date & Time is shown below.

MEGNAC SP-X EALTH METHINDUSTRIATE New Online Date & Time Name: (If the time zone is updated from this group of manual offset (METHC times are), the InterprintMap selective features will be disabled. The new time zone settings will be reflected on the page way after being issued. Configure Date & Time Select Time Zone Jul 22, 2021 8:51:09 AM (Etc/OMT) - ManualOffset/Etc/OMT Automaticly, WTD Date & Time Primary HTTP Server post-irp.org Secondary HTTP Server Kmx.mxt.gov

The Date & Time section consists of the following fields:

Configure Date & Time: Displays Time zone list containing the UTC offset along with the locations and Navigational line to select the location which can be used to display the exact local time.

Automatic NTP Date & Time: Automatically synchronizes Date and Time with the NTP Server. Primary NTP Server: Configures a primary NTP server to use when automatically setting the date and time.

Secondary NTP Server: Configures a secondary NTP server to use when automatically setting the date and time.

Save: Saves the configured settings.

Procedure

1. Select the Time zone location from the map.

2. Enable Automatic NTP Date & Time.

3. In the Primary NTP Server / Secondary NTP Server field, specify the NTP server for the device.

Note: Secondary NTP server is optional field. If the Primary NTP server is not working fine, then the Secondary NTP Server will be used.

1. Enable Automatic Date & Time option.
2. Click Save button to save the settings.

2-6-3 External User Services

LDAP/E-Directory Settings

The Lightweight Directory Access Protocol (LDAP)/E-Directory Settings is an application protocol for querying and modifying data of directory services implemented in Internet Protocol (IP) networks.

In Web GUI, LDAP is an Internet protocol that BMC can use to authenticate users. If you have an LDAP server configured on your network, you can use it as an easy way to add, manage and authenticate BMC users. This is done by passing login requests to your LDAP Server. This means that there is no need to define an additional authentication mechanism, when using the BMC. Since your existing LDAP Server keeps an authentication centralized, you will always know who is accessing the network resources and can easily define the user or group- based policies to control access.

To open External User Services page, click Settings > External User Services from the menu bar. A sample screenshot of External User Services page is shown below.

MEGARAC SP-X IDAPR MAY 2021 NEWSPX User Online Quick Links... Dashboard Server System Inventory File Information Logic & Resources Settings Remode Control Usage/Redistribution Power Control Maintenance Tags out External User Services IDAPR Directory Settings Active Directory Settings RADIUS Settings

To open LDAP/E-DIRECTORY Settings page, click Settings > External User Services > LDAP/E-Directory Settings from the menu bar.

A sample screenshot of External User Services page is shown below.

MEGARAC SP-X C:\Users\MIE\DATA\MIE\DATA\MIE\DATA\MIE\DATA\MIE\DATA\MIE\DATA\MIE\DATA\MIE\DATA\MIE\DATA\MIE\DATA\MIE\DATA\MIE\DATA\MIE\DATA\MIE\DATA\MIE\MIE\MIE\MIE\MIE\MIE\MIE\MIE\MIE\MIE\MIE\MIE\MIE\MIE\MIE\MIE\MIE\MIE\MIE\MIE\MIE\MIE\MIE\MIE\MIE\MIE\MIE\MIE\MIE\MIE\MIE\MIE\MIE\MIE\nLDAP/E-Directory Settings\nGeneral Settings\n Puzzle Groups\nName Settings External User Settings LDAP/E-Directory Settings

The fields in the LDAP/E-Directory Settings page are explained below.

General Settings: Configures LDAP/E-Directory Settings. Options are Enable LDAP/E-Directory Authentication, IP Address, Port and Search base.

Role Groups: Adds a new role group to the device. Alternatively, double click on a free slot to add a role group.

Procedure

1. In the LDAP/E-Directory Settings page, click General Settings. A sample screenshot of General LDAP Settings page is given below.

MEGARUC SP-X 100% AR AVR 2003/08/2019 (EPC) © Next Offline Quick URL... Default Server Systems Inventory Proxy Information Legal & Requests Set Rep Nevada Control Intage Infrastructure Power Control Maintenance Sign out General LDAP Settings Explain LDAPPS-Directory Authentication Encryption Type No Encryption ShareX Existential/Static Type IP Address PDB% Server Address Port: 265 Free: 0% e.g., e.g. e.g. e.g. e.g. e.g. e.g. e.g. e.g. e.g. e.g. e.g. e.g. e.g. e.g. e.g. e.g. e.g. e.g. e.g. e.g. e.g. e.g. e.g. e.g. e.g. e.g. e.g. e.g. e.g. e.g. e.g. e.g. e.g. e.g. a Access: Authentication and Received Search Date e.g., e.g. e.g. e.g. e.g. e.g. e.g. e.g. e.g. e.g. e.g. e.g. e.g. e.g. e.g. Attribute of User Login on Save US - English S.No. Readout AIA/AIA

Source: Settings: Empirical User Settings: LDAPPS-Clamping Settings: General LDAP Settings

1. Click Enable LDAP/E-Directory Authentication, to enable LDAP/E-Directory Settings.
2. Select the Encryption Type for LDAP/E-Directory.

Note: Configure the proper port number, when SSL is enabled.

1. Select the Common Name Type.

2. Enter the IP address of LDAP server in the Server Address field.

Note: IP Address made of 4 numbers separated by dots as in 'xxx.xxx.xxx.xxx'.

Each Number ranges from 0 to 255.

First Number must not be 0.

Supports IPv4 Address format and IPv6 Address format.

Configure FQDN address, when using StartTLS with FQDN.

1. Specify the LDAP Port in the Port field.

Note: Default Port is 389.

For SSL connections, default port is 636.

The Port value ranges from 1 to 65535.

Port 80 is blocked for TCP/UDP protocols.

1. Specify the Bind DN that is used during bind operation, which authenticates the client to the server.

Note: Bind DN is a string of 4 to 63 alpha-numeric characters.

It must start with an alphabetical character.

Special Symbols like dot(.), comma(,), hyphen(-), underscore(_) , equal-to(=) are allowed.

Example: cn=manager, ou=login, dc=domain, dc=com

1. Enter the password in the Password field.

Note: Password must be at least 1 character long.

Blank space is not allowed.

This field will not allow more than 47 characters.

1. Enter the Search Base. The Search base allows the LDAP server to find which part of the external directory tree to be searched. The search base may be something equivalent to the organization or the group of external directory.

Note: Search base is a string of 4 to 64 alpha-numeric characters.

must start with an alphabetical character.

Special Symbols like dot(.), comma(,), hyphen(-), underscore(_) , equal-to(=) are allowed.

Example: ou-login, dc-domain, dc-com

1. Select Attribute of User Login to find the LDAP/E-Directory server which attribute should be used to identify the user.

Note: It only supports cn or uid.

1. Select CA Certificate File from the Browse field to identify the certificate of the trusted CA certs.
2. Select the CA Certificate File to find the client certificate filename.
3. Select Private Key to find the client private key filename.

Note: All the 3 files are required, when StartTLS is enabled.

1. Click Save to save the settings.

To add a new Role Group

1. In the LDAP/E-Directory Settings page, click Role Groups and select a blank row.
2. Click Add Role Group or alternatively double click on the blank row to open the Add Role group page as shown in the screenshot below.

NEGARAC SP-X BLUE LINE JAN'S REDUATION PROC Host Online Quick Links... Qualiforand Sensor Systems Inventory mru manufacturers Logx & Reports Settings Remode Control Image Restoration Power Control Maintenance Sign out 2021-07-22 17:13:03 (MTO-40080-08FT) Role Groups Driver Driver Board Documentate Name Name Name Name

1. In the Group Name field, enter the name that identifies the role group.

Note: Role Group Name is a string of 64 alpha-numeric characters.

Special symbols hyphen and underscore are allowed.

1. In the Group Domain field. Enter the Role Group Domain where the role group is located.

Note: Domain Name is a string of 4 to 64 alpha-numeric characters.

t must start with an alphabetical character.

Special Symbols like dot(.), comma(,), hyphen(-), underscore(_) , equal-to(=) are allowed.

Example: cn=manager, ou=login, dc=domain, dc=com

1. In the Group Privilege field, enter the level of privilege (User, Administrator, Operator, None) to assign to this role group.

2. Select one or both of the required options

3. KVM Access

4. VMedia Access

5. Click Save to save the new role group and return to the Role Group List.

Active Directory Settings

An active directory is a directory structure used on Microsoft Windows based computers and servers to store information and data about networks and domains. An active directory (sometimes referred to as AD) does a variety of functions including the ability to provide information on objects. It also helps to organize these objects for easy retrieval and access, allows access by end users and administrators and allows the administrator to set security up for the directory.

Active Directory allows you to configure the Active Directory Server Settings. The displayed table shows any configured Role Groups and the available slots. You can modify, add or delete role groups from here. Group domain can be the AD domain or a trusted domain. Group Name should correspond to the name of an actual AD group.

Note: To view the page, you must be at least a User and to modify or add a group, you must be an Administrator.

To open Active Directory Settings page, click Settings > External User Settings > Active Directory from the menu bar. A sample screenshot of Active Directory Settings page is shown below.

MEGARAC SP-X TITLE SP AUTO (2021) RECO(US 476) Next Online C:\Users\1.1\AML InUID Board Server System tray inventory FRA information Logo & Resources Settings Remode Control Image Connection Power Control Watchhome Sign out Active directory Settings General Settings Role Setup Home Settings External User Settings Linked Devices Settings

The fields in the Active Directory page are explained below.

General Settings: Configures Active Directory General Settings. Options are Enable Active Directory Authentication, Secret User Name, Secret Password, User Domain Name, and up to three Domain Controller Server Addresses.

Role Groups: Adds a new role group to the device. Alternatively, double click on a free slot to add a role group.

Procedure

Entering the details in General Active Directory Settings page:

1. Click on General Settings to open the General Active Directory Settings page.

NEGARAC SP-X 100% OFF AUTO-DRAWINGS-8FC Test Online Quick Links Lastboard Server Systems Inventory File Information Logic & Requests Settings Remote Control Logos-Modestock Power Control Maintenance Sign out General Active Directory Settings Creativa Active Directory authentication Std. Secret User Name Secret Password User Domain Name Domain Controller Server Address 3 Domain Controller Server Address 3 Domain Controller Server Address 2 Save USE - English Internet Core Settings Backset Security Settings Control Action Client(s) Settings

1. In the Active Directory Settings page, check/uncheck the Enable Active Directory Authentication check box to enable/disable Active Directory Authentication.

Note: If Active Directory Authentication is enabled, enter the required information access the Active Directory server.

1. Specify the Secret user name and password in the Secret User Name and Secret Password fields respectively.

Note: Secret username/password for Active Directory is not mandatory. When secret name & password is empty, Authentication fails will be always treated as Invalid sword error.

For Invalid Password error PAM will not try other authentication methods. So it is recommended to keep Active Directory in the last location in PAM order.

User Name is a string of 1 to 64 alpha-numeric characters.

It must start with an alphabetical character.

It is case-sensitive.

Special characters like comma, period, colon, semicolon, slash, backslash, square brackets, angle brackets, pipe, equal, plus, asterisk, question mark, ampersand, double quotes, space are not allowed.

Password must be at least 6 character long and will not allow more than 127 characters.

1. Specify the Domain Name for the user in the User Domain Name field. E.g. MyDomain.com

2. Configure IP addresses in Domain Controller Server Address 1, Domain Controller Server Address 2 and Domain Controller Server Address 3.

Note: IP address of Active Directory server: At least one Domain Controller Server dress must be configured. IP Address made of 4 numbers separated by dots as in "xxx.xxx.xxx.xxx".

Each number ranges from 0 to 255.

First number must not be 0.

Domain Controller Server Addresses will supports IPv4 Address format and IPv6 Address format.

1. Click Save to save the entered settings and return to Active Directory Settings page.

Role Groups

To open Role Group page, click Settings > External User Settings > Active Directory Settings > Role Groups from the menu bar. A sample screenshot of Role Groups page is shown below.

13.02.820 Aug 20 2021 01:51:00 UTC Host Online Quick Links... Dashboard Sensor System Inventory FRU Information Logs & Reports Settings Remote Control Image Redirection Power Control Maintenance Sign out Role Groups Home - Settings - External User Settings - Active directory Settings - Role Groups Midtest Administrator KVM VMedia sit.com None None None None

The fields in the Role Group page are explained below.

Role Group Name: The name that identifies the role group in the Active Directory.

Note: Role Group Name is a string of 64 alpha-numeric characters.

Special symbols hyphen and underscore are allowed.

Group Name: This name identifies the role group in Active Directory.

Note: Role Group Name is a string of 64 alpha-numeric characters.

Special symbols hyphen and underscore are allowed.

Group Domain: The domain where the role group is located.

Note: Domain Name is a string of 255 alpha-numeric characters.

Special symbols hyphen, underscore and dot are allowed.

Group Privilege: The level of privilege to assign to this role group.

KVM Access: Provides access to KVM for AD authenticated role group user.

VMedia Access: Provides access to VMedia for AD authenticated role group user.

To add a new Role Group

1. In the Active Directory Settings page, select a Role Group and click Add Role Group or alternatively double click on the blank row to open the Add Role group page as shown in the screenshot below.

MEGARAC SP-X 15.01.39 AD 32 DWS14021-01 WRC DB/CB 16.027.206 © Float Options Quick Links Dashboard Sinaay System Inventory FIRE Information Logo & Reports Settings Remote Control Image RedSection Player Control Maintenance Signout © 2000-01-01 18:30:49 (S7C+00:09 UTC) Role Groups Group Name adjust Group Description sh.coms Group Profileges Administrator KVM Access kMedia Access Save US - English Sign Sendlog admin File Groups Role Groups Browse Settings External User Settings Active Directory Settings Role Groups Role Groups Activate Windows Go at Settings to access Windows

1. In the Group Name field, enter the name that identifies the role group in the Active Directory.

Note: Role Group Name is a string of 64 alpha-numeric characters.

Special symbols hyphen and underscore are allowed.

1. In the Group Domain field, enter the domain where the role group is located.

Note: Domain Name is a string of 255 alpha-numeric characters. Special symbols /phen, underscore, and dot are allowed.

1. In the Group Privilege field, enter the level of privilege to assign to this role group.

2. Select the required options

3. KVM Access

4. VMedia Access

5. Click Save to add the new role group and return to the Role Group List.

To Delete a Role Group

1. In the Role Groups Page, select the row that you want to delete.
2. Click Delete Role Group.

RADIUS Settings

RADIUS is a modular, high performance and feature-rich RADIUS suite including server, clients, development libraries and numerous additional RADIUS related utilities.

In Web GUI, this page is used to set the RADIUS Authentication.

To open RADIUS Settings page, click Settings > External User Settings > RADIUS Settings from the menu bar. A sample screenshot of RADIUS Settings page is shown below.

NEGARAC SP-X CULS 30 JAN 9 DEB13MROKOS EFC Trust Online Quick Limits... QuickReward Sensor Typewriter Inventory Fits Influenzaion Logic & Resources Settings Remedy Control Storage Redentless Power Control Maintenance Tags out 2021-07-22 17:16:18 (UTD-00380.GMT) RADIUS Settings Service RADIUS Settings Advanced RADIUS Settings Home - Settings - External Iron Settings RADUS Settings

The fields in the General RADIUS Settings page are explained below.

Enable RADIUS Authentication: Option to enable/disable RADIUS authentication.

Server Address: The IP address of RADIUS server.

Note: IP Address (Both IPv4 and IPv6 format).

QDN (Fully Qualified Domain Name) format.

Port: The RADIUS Port number.

Note: Default Port is 1812.

Port value ranges from 1 to 65535.

Port 80 is blocked for TCP/UDP protocols.

Secret: The Authentication Secret for RADIUS server.

Note: This field will not allow more than 32 characters.

Secret must be at least 4 characters long.

Blank space is not allowed.

Enable KVM Access: This field provides access to KVM for RADIUS authenticated users.

Enable VMedia Access: This field provides access to VMedia for RADIUS authenticated users.

Save: Saves the configured settings.

Procedure

1. Enable the RADIUS Authentication check box to authenticate the RADIUS.
2. Click Advanced RADIUS Settings. This opens the Radius Authorization window as shown below.

MEGARAC SP-X TITLE MAY'S 2021 MERCELS-IFC Host Online Quick Online... Dashboard Server Synapse Inventory File Information Logs & Requests Settings Remarks Control Insight Hardware Power Control Maintenance Sign out Advanced RADIUS Settings RADIUS Authorization Administrator H34 Operator [UK] User [UK] DEP Proprietary [UK] New Access [UK] Save Home Settings General User Settings RADIR Settings Advanced RADIR Settings

Note: For Authorization Purpose, configure the Radius user with Vendor Specific

ute on the server.

These fields will not allow more than 127 characters and the "#" sign is not allowed.

Example 1:

Add Vendor-Specific attribute

cd/usr/share/freeradius

vim dictionary.adtest

(Add content below)

# dictionary.adtest

VENDOR ADTest 58

# Standard attribute

BEGIN-VENDOR ADTest

ATTRIBUTE ADTest-group 1 string

END-VENDOR ADTest

vim dictionary

(Add this line)

\$INCLUDE dictionary.adtest

Example 2:

Add users

vim users

(add content below)

"RadiusTest1" Cleartext-Password:="000000"

Service-Type=Administrative-User,

Auth-Type:=System,

ADTest-group:="H=4"

1. Click Save to save the changes made.

2-6-4 KVM Mouse Settings

In MegaRAC GUI, Redirection Console handles mouse emulation from local window to remote screen in either of three methods. User has to be an Administrator to configure this option. To view the Supported Operating Systems for Mouse Mode, click Mouse Mode.

To open KVM Mouse setting page, click Settings > KVM Mouse Setting from the menu bar. A sample screenshot of KVM Mouse Settings page is shown below.

NEGAURC SP-X SQL Server NATI DEGREESO 4V6 View Before Quick Links Default Board Sensor Symbol Directory File Information Logic & Response Settings Service Control Usage Infrastructure Power Control Maintenance Sign out KVM Mouse Setting Mouse Mode Configuration Mouse Mode Reclusive Rebuilding (Linear) Absolute Positioning (Rerboard) Other Mode (SLR) (1.00 Installation) Save Name Settings Additional Settings

The fields in the KVM Mouse Settings page are explained below.

Relative Positioning (Linux): The relative mode sends the calculated relative mouse position displacement to the server.

Absolute Positioning (Windows): The absolute position of the local mouse is sent to the server. Recommended for Windows or later Linux releases.

Other Mode (SLES-11 OS Installation): Sends the calculated displacement from the local mouse in the center position to the server.

Save: Saves the current changes.

Procedure

1. Choose either of the following as your requirement:

- Set to Absolute Positioning (Windows)

Note: Applicable for all Windows versions, versions above RHEL6, and versions above FC14.

- Set to Relative Positioning (Linux).

Note: Applicable for all Linux versions, versions less than RHEL6, and versions less FC14.

- Set to Other Mode (SLES-11 OS Installation).

Note: Recommended for SLES-11 OS Installation.

1. Click Save button to save the changes made.

2-6-5 Log Settings

In MegaRAC GUI, System and Audit log page displays a list of system logs and audit logs occurred in this device.

To open the Log Settings page, click Settings > Log Settings from the menu bar.

A sample screenshot of Log Settings page is shown below.

MEGARAC SP-X 12.01.38 AVS NEW MEGARAC SPX Map Online Quick Links... Dashboard Server System Environment File Information Logic & Resources Settings Remode Control Intangible Resource Power Control Maintenance Sign out Log Settings SQL Log Settings Policy Advanced Log Settings USE - English Log: 00000000000 Name: Settings Log Settings

The fields in the Log Settings page are explained below.

SEL Log Settings Policy

To open SEL Log Settings Policy page, click Settings > Log Settings > SEL Log Settings Policy from the menu bar. The SEL Log Settings Policy page is used to configure the log policy for the event log. A sample screenshot of SEL Log Settings Policy page is shown below.

MEGARAC SP-X MELSR AFS (MELSR)MOOS-ERC Host Online Quick Links... Dashboard Semner Digital Inventory File Information Logic & Resources Settings Semends Control Integrated DownloadBus Power Control Maintenance Sign out SEL Log Settings Policy Log Policy Linear Manage Policy Circular Manage Policy Game USE - English Log Settings SQL Log Settings Policy

Advanced Log Settings

To open Advanced Log Settings page, click Settings > Log Settings > Advanced Log Settings from the menu bar. A sample screenshot of Advanced Log Settings page is shown below.

MegaRAC SP-X URL: 01 Access: 01.0002.12.0004.07.01 URL: 01.01.01.08 Local Outlook Advanced Log Settings Server Log Local Log Remote Log Port Type UDP TCP Module Scan X 8 Remote Log Server Server Of an In-Source Remote Service Port 8 Enable Audit Log Name: Settings Log Settings Advanced Log Settings

The fields in the Advanced Log Settings page are explained below.

System Log: Check/uncheck to enable/disable the System Logs.

Local Log: Select local log to save the logs locally (BMC).

Note: Local file resides at /var/log/

Remote Log: Select remote log to save the logs in a remote machine.

Port Type: When Remote Log is enabled, user can select either UDP or TCP per requirement.

Rotate Count: Backs up the log information in back up files.

Note: Values supported are 0 and 1.

When log information exceeds the file size, the old log information is automatically moved to back up files based on the rotate count value. If rotate count is zero, then old log information gets cleared permanently.

File Size and Rotate Count options will be available only when Local Log is enabled.

Remote Log Server: This field is to specify the remote server address to log the system events.

Note: Server address will support the following:

IPv4 and IPv6 address format.

PQDN (Fully qualified domain name) format.

Remote Server Port: This field is to specify the remote server port to log the system events.

Note: Remote Log Server and Remote Server Port options will be available only when

Remote Log is enabled.

Enable Audit Log: Enables/Disables the audit log.

Save: Saves the current changes.

Procedure

1. In the System Log field, enable or disable the option.
2. Select the Log type: Local Log or Remote Log.
3. If Local Log is selected, enter the file size in the File Size field and rotate count in the Rotate Count field.

Note: If Remote Log is selected, the fields file size and rotate count need not be mentioned.

1. If Remote Log is selected, specify the Port Type, Remote Log Server, and Remote Server Port.

2. In the Audit Log field, check or uncheck the Enable option as needed.

3. Click Save to save the changes.

2-6-6 Manage Licenses

This page displays available licenses for this system and the validity period of the licenses. To open the Manage Licenses page, click Settings > Manage Licenses from the menu bar. A sample screenshot of Manage Licenses page is shown below.

MEGARAC SP-X URL:28 JAP 9 DEUT MEGROS EFC Host Online Quick URL: Dustboard Sensor Logbook Inventory File Information Logic & Algorithms Settings Remode Control Storage/Reconstruction Power Control Maintenance Tag out 2021-07-23 06:00:33 (JFTO-00385.GMT) Manage Licenses View License Add License Key

The fields in the Manage Licenses page are explained below.

View Licenses: Displays the available licenses and the validity period of the licenses.

Add License Key: Select to add a license key.

2-6-7 Media Redirection Settings

This page is used to configure the media into BMC for redirection. To open the Media Redirection page, click Settings > Media Redirection Settings from the menu bar.

A sample screenshot of Media Redirection page is shown below.

MEGARAC SP-X ELELTR A45.2013M80005-IFC Show Online Quick Limits... Qualiforand Sensor Symbol inventory File information Logic & Resources Settings Remedy Control Image Redirections Power Control Maintenance Sign out Media Redirection General Settings Used in instance Settings Remote Services Active Release/Install

The fields in the Media Redirection page are explained below.

General Settings

This option is used to configure General Media Settings. To open the General Media Settings section, click Settings > Media Redirection Settings > General Settings.

MEGARAC SP-X 12.01.28 MAY 2023 MEGARAC SP-X File Online Quick Links... Dashboard Server Syncbase inventory File information Logic & Resources Settings Remode Central Insight Audiovisual Power Control Maintenance Sign out General Settings Click here to go to license Media. Measures Media TapgedT Visual CE/DVD Visual Handbitik Back Event 26 Back Count 3 Save Home Settings Media Delivery General Settings

Remote Media Support: Enables/Disables Remote Media support, check/uncheck the box. Remote Media emulates CD/DVD/HDD images as media through BMC.

Mount CD/DVD: Enables/Disables Mount CD/DVD support, check/uncheck the check box.

Note: You can also select all the media types simultaneously.

Server Address for CD/DVD Images: Displays the address of the server where the remote media images are stored.

Path in server: Displays the source path to the remote media images.

Share Type for CD/DVD: Selects the Share Type of the remote media server either NFS, CIFS, or HTTP.

Domain Name, Username, and Password: If share type is CIFS, then enter user credentials to authenticate on the server.

Same settings for Harddisk Images: Enable/Disable to select same media type data configurations for all the remote media types.

Mount Harddisk: Enable/Disable to Mount Harddisk.

Server Address for Harddisk Images: Address of the server where the remote media images are stored.

Path in server: Displays the source path to the remote media images.

Share Type for Harddisk: Selects the Share Type of the remote media server either NFS, CIFS, or HTTP.

Domain Name, Username, and Password: If share type is CIFS, then enter user credentials to authenticate on the server.

Retry Interval: Gives time interval for each attempt to reconnect Remote Media.

Retry Count: Specifies the number of attempts to reconnect Remote Media.

Save: Saves the configurations.

VMedia Instance Settings

This page is used to configure Virtual Media device settings. To open the VMedia Instance Settings page, click Settings > Media Redirection Settings > VMedia Instance Settings from the menu bar.

A sample screenshot of VMedia Instance Settings page is shown below.

MEGARAC SP-X COLOR MENI NEDIMIKOS ETC File Edit Space Limits... Installboard Server Spdbset inventory File information Logic & Algorithms Settings Remode Control Insight Infrastructure Power Control Maintenance Sign out VMedia Instance Settings C:\MWD Device Instances 1 main disk instances 1 Resource PWM CD/DVD Device Instances 1 Resource PWM Head disk Instances 1 Power Start Mode Save

The following fields are displayed in this page:

CD/DVD device instances: The number of CD/DVD devices supported for Virtual Media redirection.

Harddisk instances: The number of hard disk devices supported for Virtual Media redirection.

Remote KVM CD/DVD device instances: The number of CD/DVD devices supported for KVM Virtual Media redirection.

Remote KVM Hard disk instances: The number of hard disk devices supported for KVM Virtual Media redirection.

Power Save Mode: Enables/Disables the virtual USB devices visibility in the host. If this option is enabled, Virtual media devices will be connected to the Host machine only at the instance launching KVM session. If this option is disabled, Virtual media devices will remain connected to the host machine all the time irrespective of KVM session status.

Save: Saves the configured settings.

Note: Virtual Media configuration changes will restart all the media services. So configuration changes will be blocked when any active media redirection is present.

Procedure

1. Select the number of CD/DVD devices, harddisk devices and remote KVM CD/DVD and hard disk devices from the respective drop-down list.

Note: Maximum of four devices can be added in CD/DVD and Harddisk drives.

1. Check/uncheck the Power Save Mode option to enable/disable the virtual USB devices visibility in the host.
2. Click Save to save the changes made.

Remote Session

In MegaRAC, this page is used to configure Remote Session configuration settings. KVM Single Port Application is enabled by default.

To open the Remote Session page, click Settings > Media Redirection Settings > Remote Session from the menu bar.

A sample screenshot of Remote Session page is shown below.

MEGARAC SP-X 12.01.30 MAY 2021 MEGARAC SP-X Main Online Quick Links... Dustboard Server Logbook inventory File Information Logic & Impacts Settings Remends Control Image Monitoring Power Control Maintenance Sign out 2021-07-23 08:53:09 (LPTC+0380-08MT) Remote Session Click here to go to Remote Control. KVM Single Port Application Keyboard Language Auto Detect (ISO) Kvky Count 3 Ready Time Interval(>|setpoint| ) 36 Server Monitor Off Feature Status Automatically KVF Server Monitor, Without KVM Launches Save

The fields in the Configure Remote Session page are explained below.

KVM Single Port Application: This item is checked (enabled) by default and is not configurable. The KVM session will not use its dedicated port whereas both Web and KVM sessions will be established only via Web Port.

Keyboard Language: Select the keyboard supported languages.

Retry Count: Retries the redirection session for certain number of attempts.

Retry Time Interval (Seconds): Gives time interval for each attempt.

Server Monitor OFF Feature Status: Enables/Disables Server Monitor OFF. If this option is enabled, you can Lock or Unlock the Local host monitor from the remote KVM window. If this option is disabled, you cannot Lock or Unlock the Local host monitor from the remote KVM window.

Automatically OFF Server Monitor, When KVM Launches: Enables/Disables Automatically OFF Server Monitor, When KVM Launches.

Save: Saves the current changes.

Note: It will automatically close the existing remote redirection either KVM or Virtual via sessions on Single Port enable/disable.

Note: Installation of Operating System on the servers via BMC CD ISO image over note KVM may take 1 to 2 hours.

Procedure

1. Check or uncheck the KVM Single Port Application option to enable Single Port Application support in BMC.
2. Choose the Keyboard Language from the list of keyboard supported languages.
3. Enter a value in the Retry Count field to set the number of attempts for retrying the redirection session.
4. Enter a value in the Retry Time Interval (Seconds) field to give time interval for each attempts.
5. Check the Server Monitor OFF Feature Status check box to enable Local Monitor ON/OFF command during runtime.
6. Check the Automatically OFF Server Monitor, When KVM Launches check box to automatically Lock the local monitor during H5Viewer launch.
7. Click Save to save the current changes.

Active Redirections

This page displays a list of Media which are being redirected currently. It shows current status and other basic information about the Media.

NEGARAC SP-X 12.01.08 ANY NEGARAC SP-X Host Online Quick Links... Dashboard Server Analysis Inventory File Information Logic & Requests Settings Remode Control Image-Redirections Power Control Maintenance sign out Active Redirections Media Type ↑ Media Instance ↑ Client Type ↑ Image Name ↑ Redirection Status ↑ Client ID ↑

2-6-8 Network Settings

The Network Settings page is used to configure the network settings for the available LAN channels. It also allows users to manage the DNS settings or configure Network Controller Sideband Interface of a device. To open the Network Settings page, click Settings > Network Settings from the menu bar.

NEGARAC SP-X CELL 36 JAS 2013 NETWORKS-IFC Host Online Quick Links... DustBoard Sensor Systems Inventory File Information Logic & Network Settings Remarks Control Image Infrastructure Power Control Maintenance Sign out Network Settings Network IP Settings Network Board Configuration Network Link Configuration DMS Configuration

Network IP Settings

To open Network IP Settings page, click Settings > Network Settings > Network IP Settings from the menu bar. A sample screenshot of Network IP Settings page is shown below.

MEGARAC SP-X EELTR MFS NELLINICOS EPL File Online Quick Links... Dashboard Sensor Integrated Inventory My Information Language & Resources Settings Remove Control Image Realdehyde Power Control Maintenance Sign out Network IP Settings Enable LAN LAN Interface Iswal0 MAC Address: DATE: 05/06/03:03 Enable IPv4 Enable IPv2 DHCP IPv4 Address: 68.250.42.70 IPv4 Platform: 255.255.255.8 IPv4 Gateway: 68.250.42.354 Enable IPv4 Enable IPv2 DHCP IPv4 Index: 0 IPv4 Address: 0 Subnet Profile Length: 0 IPv4 Connection: 0 Enable IPv4 EPLTR ID: 0 EPLTR Priority: 0 Source - Settings - Network - Research IP Settings

The fields in the Network IP Settings page are explained below.

Enable LAN: Enables/disables the LAN Settings.

LAN Interface: Lists the LAN interfaces.

MAC Address: Displays the MAC Address of the device. This is a read only field.

Enable IPv4: Enables/disables the IPv4 settings in the device.

Enable IPv4 DHCP: Enables IPv4 DHCP support for the selected interface.

IPv4 Address, IPv4 Subnet, and IPv4 Default Gateway: These fields are for specifying the static IPv4 address, Subnet Mask and Default Gateway to be configured to the device.

Note: IP Address made of 4 numbers separated by dots as in "xxx.xxx.xxx.xxx".

Each Number ranges from 0 to 255.

First Number must not be 0.

Enable IPv6: Enables/disables the IPv6 configuration settings.

Enable IPv6 DHCP: Enables/disables the IPv6 settings in the device. It dynamically configures IPv6 address using DHCP (Dynamic Host Configuration Protocol).

IPv6 Index: Specifies a static IPv6 Index to be configured to the device. E.g.: 0

IPv6 Address: Specifies a static IPv6 address to be configured to the device. E.g.: 2004::2010

Subnet Prefix Length: Specifies the subnet prefix length for the IPv6 settings.

Note: Value ranges from 0 to 128.

IPv6 Gateway: Specifies IPv6 default gateway.

Note: If core feature IPV6_COMPLIANCE is enabled, the IPV6 default Gateway field will e displayed.

Clear IPv6 Address: Check to clear the IPv6 address.

Enable VLAN: Enables/Disables the VLAN support for selected interface.

VLAN ID: The Identification for VLAN configuration.

Note: Value ranges from 1 to 4094.

LAN ID cannot be changed without resetting the VLAN configuration.

VLAN Priority: The priority for VLAN configuration.

Note: Value ranges from 0 to 7.

the highest priority for VLAN.

Save: Saves the entries.

Procedure

1. Check Enable LAN to enable LAN support for the selected interface.
2. Select the LAN Interface to be configured.
3. Check Enable IPv4 to enable IPv4 support for the selected interface.
4. Check Enable IPv4 DHCP to dynamically configure IPv4 address using DHCP.
5. If the field is disabled, enter the IPv4 Address, IPv4 Subnet and IPv4 Default Gateway in the respective fields.
6. In IPv6 Configuration, if you want to enable the IPv6 settings, check Enable IPv6.
7. If the IPv6 setting is enabled, enable or disable the option Enable IPv6 DHCP.
8. If the field is disabled, enter the IPv6 Index, IPv6 Address, Subnet Prefix length and IPv6 Gateway in the given field.
9. In VLAN Configuration, if you want to enable the VLAN settings, check Enable LAN.
10. Enter the VLAN ID in the specified field.
11. Enter the VLAN Priority in the specified field.
12. Click Save to save the entries.

Network Bond Configuration

To open the Network Bond Configuration page, click Settings > Network Settings > Network Bond Configuration from the menu bar. A sample screenshot of Network Bond Configuration page is shown below.

MEGARAC SP-X NEW NEXEERLEDOS-FRC Host Online Quick Links... Draftboard Semene Hydrofoil Inventory Fits Information Logic & Resources Settings Bemode Control Usage-Head/Drivebox Power Control Maintenance Sign out 2023-07-25 16:36:00 [JYTC-05080-0541] Network Bond Configuration Enable Boarding Auto-Configuration Bond Interface 4050 Bond Mode: active-backup Save Home Settings Downloads Resource Bond Configurations

The fields in the Network Bond Configuration page are explained below.

Enable Bonding: Check to enable network bonding.

Note: If VLAN is enabled for any slave interfaces, Bonding cannot be enabled.
isable VLAN, go to Configuration > Network > VLAN.

Auto Configuration: Check to enable automatic configuration of network interfaces.

Bond Interface: Configures bonding for network interfaces.

Note: A minimum of two network interfaces is required to enable Network Bonding for device.

Bond Mode: Displays the network bonding mode in effect. This field is not configurable.

Save: Saves the entries.

Procedure

1. Check Enable Bonding to enable network bonding for the network interfaces.
2. Check Auto Configuration to enable automatic combination of network interfaces.
3. Select a bond interface.
4. Click Save to save the entries.

Network Link Configuration

To open Network Link Configuration page, click Settings > Network Settings > Network Link Configuration from the menu bar. A sample screenshot of Network Link Configuration page is shown below.

MEGARAC SP-X LEBLER MAYE NEELIMICS-INFO Host Online Quick Links... Draftboard Server Hybridset Inventory Fits Information Logic & Response Settings Bemends Control Language/Communication Power Control Maintenance Tags out Network Link Configuration LAR Interface info0 Auto Regression Link speed 300Mbps Degree Mode Multi-Duplex Half Claplex Save

The fields in the Network Link Configuration page are explained below.

LAN Interface: Select a network interface.

Auto Negotiation: Check to enable automatic negotiation.

Link Speed: Configures the link speed.

Note: The link speed can be 10, 100, or 1000 Mbps.

speed of 1000 Mbps is not applicable when Auto Negotiation is disabled.

Duplex Mode: Select the duplex mode.

Note: This setting option cannot be configured if Auto Negotiation is enabled.

Save: Saves the entries.

Procedure

1. Select a network interface you want to configure from LAN Interface.
2. Check Auto Negotiation to enable automatic configuration.
3. Configure the link speed.

Note: This setting option cannot be configured if Auto Negotiation is enabled.

1. Select the duplex mode.
2. Click Save to save the entries.

DNS Configuration

The Domain Name System (DNS) is a distributed hierarchical naming system for computers, services, or any resource connected to the Internet or a private network. It associates the information with domain names assigned to each of the participants. Most importantly, it translates domain names meaningful to humans into the numerical (binary) identifiers associated with networking equipment for the purpose of locating and addressing these devices worldwide. The DNS Server settings page is used to manage the DNS settings of a device.

To open DNS Server Settings page, click Settings > Network Settings > DNS Configuration from the menu bar. A sample screenshot of DNS Configuration page is shown below.

NEGARAC SP-X ELELIR NPS 2021 MSCI-SPX Host Online Quick Links Dashboard Service Systems Inventory FBU Information Logic & Resources Settings Bemeral Control Insight Mechanical Power Control Maintenance Sign out DNS Configuration DNS Enabled noDNS Enabled Host Names Setting Automatics Manual Host Names ADDRIDESTSRADES BAC Registration Settings BAC Interface Monitor Register BAC Registration interfaces PhoneInfo DHCP Client PQBR Professional TSHS-Configuration New Authentication structured Current TSHS Private File Info Not Available New TSHS Private File Domain Setting Automatics Manual Domain Name: gjgalyb@insta Database Name Server Setting Automatics Manual DNS Server 1 JL.L.S.D. DNS Server 2 : DNS Server 3 : Name Settings Network Settings DNS Configuration

Domain Name Service Configuration

DNS Enabled: Enables/Disables all the DNS Service configurations.

mDNS Enabled: Enables/Disables Multicast DNS.

Host Name Setting: Choose either Automatic or Manual settings.

Host Name: It displays host name of the device. If the Host setting is chosen as Manual, then specify the host name of the device.

Note: Value ranges from 1 to 64 alpha-numeric characters.

Special characters '-'(hyphen) and '-' (underscore) are allowed. It must not start or end with a '-' (hyphen). IE browsers won't work correctly if any part of the host name contain underscore (_) character.

BMC Registration Settings

BMC Interface: Options to register the BMC through the interfaces (eth0 & eth1).

Register BMC: Registers BMC through registration method.

Registration Method: Options to register the BMC are through Nsupply or DHCP Client FQDN or Hostname.

TSIG Configuration

TSIG Authentication Enabled: Check this box to enable TSIG authentication while registering DNS via nsupdate. Separate TSIG files can be uploaded for each LAN interface.

Current TSIG Private File: The information of current TSIG private file along with its uploaded date/time will be displayed (read-only).

New TSIG Private File: Browse and navigate to the TSIG private file.

Note: TSIG file should be of private type.

Domain Setting

Automatic: If you select Automatic, the Domain Name cannot be configured as it will be done automatically. The field will be disabled.

Manual: If the Domain Setting is chosen as Manual, then specify the domain name of the device.

Note: If you select Automatic, it displays the Domain interface option. If you selectUAL, it displays domain name.

Domain Name: It displays the domain name of the device.

Domain Name Server Setting

Automatic: If you select Automatic, the DNS Interface option should be explained.

Manual: Specify the DNS (Domain Name System) server address to be configured for the BMC.

IP Priority:

• If IP Priority is IPv4, it will have 2 IPv4 DNS servers and 1 IPv6 DNS server.
• If IP Priority is IPv6, it will have 2 IPv6 DNS servers and 1 IPv4 DNS server.

Note: This is not applicable for Manual configuration.

DNS Server 1, 2 & 3

To specify the DNS (Domain Name System) server address to be configured for the BMC.

Note: IPv4 Addresses should be given in dotted decimal representation.

Addresses are supported and must be global unicast addresses.

DNS Server Address will support the following:

• IPv4 Address format.
• IPv6 Address format.

Save: Saves the current changes.

Procedure

1. Check the option DNS Enabled to enable all the DNS Service configurations.
2. Check the option mDNS Enabled to enable Multicast DNS.
3. Choose the Host Name Setting either Automatic or Manual.

Note: If you choose Automatic, you need not enter the Host Name and if you choose equal, you need to enter the Host Name.

1. Enter the Host Name in the given field if you have chosen Manual Configuration.
2. Under Register BMC, choose the BMC's network port to register with DNS settings.

3. Check Register BMC to register with DNS settings.

4. Nsupdate - Choose Nsupdate option to register with DNS server using nsupdate application.

5. DHCP Client FQDN - Choose DHCP Client FQDN option to register with DNS Server using DHCP option 81.
6. Hostname - Choose Hostname option to register with DNS server using DHCP option 12.

Note: Hostname option should be selected, if the DHCP client FQDN option is not reported by DHCP server.

1. In TSIG Configuration, check TSIG Authentication Enabled enable TSIG authentication while registering DNS via nsupdate.

2. The current file name will be displayed in Current TSIG Private file info field.

3. To view a new one, click New TSIG private file to browse and navigate to the TSIG private file.

4. In Domain Settings,

5. Select the domain settings (Automatic or Manual).

6. Enter the Domain Name in the given field if the option. Manual is being selected in domain settings field.

7. In Domain Name Server Setting,

8. Select the DNS Name Server Setting (Automatic or Manual).

9. Choose the IP Priority, either IPv4 or IPv6.

10. Enter the DNS Server address.

11. In DNS Server 1, DNS Server 2 and DNS Server 3, enter the server addresses to be configured for the BMC.

12. Click Save to save the entries.

2-6-9 PAM Order Settings

This page is used to configure the PAM ordering for user authentication in to the BMC.

To open PAM Ordering page, click Settings > PAM Order Settings from the menu bar. A sample screenshot of PAM Order page is shown below:

NEGARAC SP-X URL: 01-23-17.0765 (LTD-03380.047) PAM Order PAM authorized/Carbox Order IPDB LOWF ACTIVE DIRECTORY ADDRESS Save

The fields in the PAM Order page are explained below.

PAM Authentication Order: It shows the list of available PAM modules supported in BMC.

Note: It is recommended to not to keep same username for different PAM modules. thentication fails, the reason of fail could be invalid User or Invalid Password.

If Radius Authentication fails, we can't differentiate whether it is invalid user or invalid password. So it is always treated as Invalid username error and PAM will try other Authentication Methods.

If AD contains secret username & password as empty, Authentication fails will be always treated as Invalid Password error. For Invalid Password error PAM will not try other Authentication Methods. So it is recommended to keep AD in the last location in PAM order.

Save: Saves the configuration.

Procedure

1. Select the required PAM module and click and drag the required PAM module. It can be moved UP or DOWN to change its arrangement order.
2. Click Save to save any changes made.

Note: Whenever the configuration is modified, the web server will be restarted matically. Logged-in session will be logged out.

2-6-10 Platform Event Filter

Platform Event Filter (PEF) provides a mechanism for configuring the BMC to take selected actions on event messages that it receives or has internally generated. These actions include operations such as system power-off, system reset, as well as triggering the generation of an alert.

To open PEF Management Settings page, click Settings > Platform Event Filter from the menu bar.

MEGARAC SP-X ESELE AI & JOESELE Quick Links Dashboard Server Electronic Inventory File Information Logic & Improve Settings Network Control Usage/Modemscale Power Control Maintenance Sign-out Platform Event Filters Start EPIDINS Auto Puzzles LPS SKEUANSYS USE ENGLISH AUTO Puzzles LPS SKEUANSYS

Event Filters

A PEF implementation is recommended to provide at least 40 entries in the event filter table. A subset of these entries should be pre-configured for common system failure events, such as over-temperature, power system failure, fan failure events, etc. Remaining entries can be made available for 'OEM' or System Management Software configured events. Note that individual entries can be tagged as being reserved for system use - so this ratio of pre-configured entries to run-time configurable entries can be reallocated if necessary.

NEGARAC SPX DATA: 2023-07-25 (UNIVERSITY) (UNIVERSITY OF) Event Filters Quick Links... Default Board Server Symbol summary File Information Logo & Requests Settings Remote Control Integrant Release Power Control Maintenance Sign out Event Filters All Configured Low Configured PDF ID: 1 (Executive) when all servers switches to critical state name PDF ID: 5 (Executive) when all servers switches to critical state name PDF ID: 9 (Executive) when all servers switches to critical state name PDF ID: 13 (Executive) when all servers switches to critical state name PDF ID: 2 (Executive) when all servers switches to critical state name PDF ID: 6 (Executive) when all servers switches to critical state name PDF ID: 7 (Executive) when all servers switches to critical state name PDF ID: 14 (Executive) when all servers switches to critical state name PDF ID: 15 (Executive) when all servers switches to critical state name PDF ID: 8 (Executive) when all servers switches to critical state name PDF ID: 9 (Executive) when all servers switches to critical state name PDF ID: 10 (Executive) when all servers switches to critical state name PDF ID: 11 (Executive) when all servers switches to critical state name PDF ID: 12 (Executive) when all servers switches to critical state name PDF ID: 13 (Executive) when all servers switches to critical state name PDF ID: 14 (Executive) when all servers switches to critical state name PDF ID: 15 (Executive) when all servers switches to critical state name

The fields in the Platform Event Filters tab are explained below. This page contains pre-configured 40 events with PEF IDs.

Procedure

1. Click the Event Filters section to configure the event filters in the available slots.
2. To add an Event Filter entry, select a free section to open the Event Filter entry page. A sample screenshot of Event Filter Configuration page is shown below.

MEGARAC SP-X CENSER ANY DREAMS (F5) Treat History Event Filter Configuration Enable this filter Event sensitivity to triggers Any settings: Cancel Filter Action Alert Power Action Access Alert Delivery Group Member Flow Data Generator ID 1 ID2 Generator ID 2 ID3 Generator Type Slave Software Show Address/Software ID Channel Number 0 64MB Device LLC 0 Sensor type 42 formats Sensor name 42 formats Event Options All Events Event XLogo 0 Event Data 3 AND Read 0 Event Data 2 Compliance 1 0 Event Data 3 Compliance 3 0 Event Data 2 AND Read 0 Event Data 3 Compliance 1 0 Event Data 3 Compliance 3 0 Event Data 3 AND Read 0 Event Data 3 Compliance 1 0 Event Data 3 Compliance 2 0 Options Help

In the Event Filter Configuration section:

• In Enable this filter, check this option to enable the PEF settings.
  • In Event Severity to trigger, select any one of the Event severity from the list.
• Check Event Filter Action Alert to enable alerts for event filter actions.
• Select any one of the Power Action either Power down, Power reset or Power cycle from the drop down list

- Choose any one of the configured Alert Policy Group Number from the drop down list.

Note: Alert Policy has to be configured under Settings > PEF > Alert Policy.

• Check Raw Data option to fill the Generator ID with raw data.
• Generator ID 1 field is used to give raw generator ID 1 data value.
• Generator ID 2 field is used to give raw generator ID 2 data value.

Note: In RAW data field, specify hexadecimal value prefix with '0x'.

• In the Event Generator section, choose the event generator as Slave Address - if event was generated from IPMB. Otherwise as System Software ID - if event was generated from system software.
• In the Slave Address/Software ID field, specify corresponding I2C Slave Address or System Software ID.
• Choose the particular Channel Number that event message was received over. Or choose '0' if the event message was received via the system interface, primary IPMB, or internally generated by the BMC.
• Choose the corresponding IPMB Device LUN if event is generated by IPMB.
• Select the Sensor type of sensor that will trigger the event filter action.
  • In the Sensor name field, choose the particular sensor from the sensor list.
• Choose Event Option to be either All Events or Sensor Specific Events.
• Event Trigger field is used to give Event/Reading type value.

Note: Value ranges from 0 to 255.

- Event Data 1 AND Mask field is used to indicate wildcarded or compared bits.

Note: Value ranges from 0 to 255.

- Event Data 1 Compare 1 & Event Data 1 Compare 2 fields are used to indicate whether each bit position's comparison is an exact comparison or not.

Note: Value ranges from 0 to 255.

• Event Data 2 AND Mask field is similar to Event Data 1 AND Mask.
• Event Data 2 Compare 1 & Event Data 2 Compare 2 fields are similar to Event Data 1 Compare 1 and Event Data 1 Compare 2 respectively.
• Event Data 3 AND Mask field is similar to Event Data 1 AND Mask.
• Event Data 3 Compare 1 & Event Data 3 Compare 2 fields are similar to Event Data 1 Compare 1 and Event Data 1 Compare 2 respectively.

1. Click Save to save the changes and return to event filter list.
2. Click Delete to delete the existing filter.

Alert Policies

This page is used to configure the Alert Policy for the PEF configuration. You can add, delete or modify an entry in this page.

NEGABLE SPX LAB CHAMET 1 Send To 0 Group 1 (Standard) Always send alert to the destination LAB Channel 1 Send To 0 Group 2 (Standard) Always send alert to the destination LAB Channel 1 Send To 0 Group 3 (Standard) Always send alert to the destination LAB Channel 1 Send To 0 Group 4 (Standard) Always send alert to the destination LAB Channel 1 Send To 0 Group 5 (Standard) Always send alert to the destination LAB Channel 1 Send To 0 Group 6 (Standard) Always send alert to the destination LAB Channel 1 Send To 0 Group 7 (Standard) Always send alert to the destination LAB Channel 1 Send To 0 Group 8 (Standard) Always send alert to the destination LAB Channel 1 Send To 0 Group 9 (Standard) Always send alert to the destination LAB Channel 1 Send To 0 Group 10 (Standard) Always send alert to the destination LAB Channel 1 Send To 0 Group 11 (Standard) Always send alert to the destination LAB Channel 1 Send To 0 Group 12 (Standard) Always send alert to the destination LAB Channel 1 Send To 0 Group 13 (Standard) Always send alert to the destination LAB Channel 1 Send To 0 Group 14 (Standard) Always send alert to the destination LAB Channel 1 Send To 0 Group 15 (Standard) Always send alert to the destination LAB Channel 1 Send To 0 Group 16 (Standard) Always send alert to the destination LAB Channel 1 Send To 0 Group 17 (Standard) Always send alert to the destination LAB Channel 1 Send To 0 Group 18 (Standard) Always send alert to the destination LAB Channel 1 Send To 0 Group 19 (Standard) Always send alert to the destination LAB Channel 1 Send To 0 Group 20 (Standard) Always send alert to the destination LAB Channel 1 Send To 0 Group 21 (Standard) Always send alert to the destination LAB Channel 1 Send To 0 Group 22 (Standard) Always send alert to the destination LAB Channel 1 Send To 0 Group 23 (Standard) Always send alert to the destination LAB Channel 1 Send To 0 Group 24 (Standard) Always send alert to the destination LAB Channel 1 Send To 0 Group 25 (Standard) Always send alert to the destination LAB Channel 1 Send To 0 Group 26 (Standard) Always send alert to the destination LAB Channel 1 Send To 0 Group 27 (Standard) Always send alert to the destination LAB Channel 1 Send To 0 Group 28 (Standard) Always send alert to the destination LAB Channel 1 Send To 0 Group 29 (Standard) Always send alert to the destination LAB Channel 1 Send To 0 Group 30 (Standard) Always send alert to the destination LAB Channel 1 Send To 0 Group 31 (Standard) Always send alert to the destination LAB Channel 1 Send To 0 Group 32 (Standard) Always send alert to the destination LAB Channel 1 Send To 0 Group 33 (Standard) Always send alert to the destination LAB Channel 1 Send To 0 Group 34 (Standard) Always send alert to the destination LAB Channel 1 Send To 0 Group 35 (Standard) Always send alert to the destination LAB Channel 1 Send To 0 Group 36 (Standard) Always send alert to the destination LAB Channel 1 Send To 0 Group 37 (Standard) Always send alert to the destination LAB Channel 1 Send To 0 Group 38 (Standard) Always send alert to the destination

The fields in the Alert Policies page are explained below.

Policy Group Number: Displays the policy number of the configuration.

Enable this alert: Enables/Disables the policy settings.

Policy Action: Chooses any one of the Policy set values (0-5) from the list.

0 - Always send alert to this destination.

1 - If alert to previous destination was successful, do not send alert to this destination. Proceed to next entry in this policy set.
2 - If alert to previous destination was successful, do not send alert to this destination. Do not process any more entries in this policy set.
3 - If alert to previous destination was successful, do not send alert to this destination. Proceed to next entry in this policy set that is to a different channel.
4 - If alert to previous destination was successful, do not send alert to this destination. Proceed to next entry in this policy set that is to a different destination type.

LAN Channel: Chooses a particular channel from the available channel list.

Destination Selector: Chooses a particular destination from the configured destination list.

Note: LAN Destination has to be configured under Settings > Platform Event Filters AN Destinations.

Event Specific Alert String: Specifies an event-specific Alert String.

Alert String Key: Specifies which string is to be sent for this Alert Policy entry.

Save: Saves the Alert Policies entries.

Delete: Deletes the selected configured Alert Policy.

Procedure

1. In the Alert Policies Section, select the slot for which you have to configure the Alert policy. That is, in the Alert Policies page, if you have chosen Alert Policy Group Number as 4, you have to configure the 4th slot (the slot with Policy Number 4) in the Alert Policy Tab.
2. Select the slot and click on the empty slot to open the Alert Policies page as shown in the screenshot below.

NEGARAC SP-X ELELTR AUY 2013 MEGARAC SP-X Host Online Quick Links... Defaultboard Sensor Systems Inventory File Information Logic & Resources Settings Benedia Central Usage-Indirective Power Control Maintenance Sign out Alert Policies Policy Group Transfer 1 Enable Info alert Policy access Always send alert to this destination LAR Channel: 1 Destination Selector Event Specific Alert Siting Alert Siting Key Options Save US - English Topic Headlink Admins Name: Settings - Platform Event Files - Alert Policies - Sign Policy

1. Select Policy Group Number from the drop-down list.

2. Check Enable this alert to enable the policy settings.

3. Choose any of the Policy Action from the list.

4. Choose particular LAN Channel from the available channel list.
5. In the Destination Selector, choose particular destination from the configured destination list.

Note: LAN Destination has to be configured under Settings > Platform Event Filters LAN Destinations.

That is if you select the number 4 for destination selector in Alert Policy Entry page, then you have to configure the 4th slot (LAN Destination Number 4) in the LAN Destinations tab.

1. Enable Event Specific Alert String, if the Alert policy entry is Event Specific.
2. In the Alert String Key field, choose any one value that is used to look up the Alert String to send for this Alert Policy entry.

Note: Using Web UI, Alert strings cannot be configured but option for Event Specific port strings can be enabled/disabled. There is an option to select only the alert string keys, but alert strings has to be configured using IPMI Command (Set PEF Config parameter 'Alert String').

1. Click Save to save the new alert policy and return to Alert Policy list.
2. Click Delete to delete a configuration.

LAN Destinations

This page is used to configure the LAN destination of PEF configuration.

A sample screenshot of LAN Destination page is given below.

NEGARAC SPX LAN DESTINATIONS LAX Channel 1 LAX Destination 1 SNMP Tag Send To LAN Channel 2 LAX Destination 2 SNMP Tag Send To LAN Channel 3 LAX Destination 3 SNMP Tag Send To LAN Channel 4 LAX Destination 4 SNMP Tag Send To LAN Channel 5 LAX Destination 5 SNMP Tag Send To LAN Channel 6 LAX Destination 6 SNMP Tag Send To LAN Channel 7 LAX Destination 7 SNMP Tag Send To LAN Channel 8 LAX Destination 8 SNMP Tag Send To LAN Channel 9 LAX Destination 9 SNMP Tag Send To LAN Channel 10 LAX Destination 10 SNMP Tag Send To LAN Channel 11 LAX Destination 11 SNMP Tag Send To LAN Channel 12 LAX Destination 12 SNMP Tag Send To LAN Channel 13 LAX Destination 13 SNMP Tag Send To

Select any empty slot to configure LAN Destinations.

The fields in the LAN Destination Configuration page are explained below.

MEGARAC SPX MAGLIER M&T DESCRIPTION Host Online Quick Links Installboard Tanner Cycleres Inventory File Information Log & Requests Settings Remote Control Image-Substructure Power Control Main-Romaine Sign-Out LAN Destination Configuration LAN Channel: 1 LAN Description: 3 Description Type: SNMP Trap 8-mail SNMP Destination address: 6.0.0.0 MAC Standarder Email Subject Email Message Send to Save Home - Settings - Platform Name/Phone - LAN Destination - LAN Destination Configuration

LAN Channel: Displays LAN Channel Number for the selected slot (read-only).

LAN Destination: Displays ID for setting Destination Selector of Alert Policy (read-only).

Destination Type: Destination type can be either an SNMP Trap or an E-mail alert. For E-mail alerts, the four fields - SNMP Destination Address, BMC User Name, Email subject and Email message needs to be filled. For SNMP Trap, only the SNMP Destination Address has to be filled.

SNMP Destination Address: If Destination type is SNMP Trap, then enter the IP address of the system that will receive the alert. Destination address will support the following:

• IPv4 address format.
• IPv6 address format.

BMC User Name: If Destination type is Email Alert, then choose the user to whom the email alert has to be sent. Email address for the user has to be configured under Settings > User Management.

Email Subject & Email Message: These fields must be configured if email alert is chosen as destination type. An email will be sent to the configured email address of the user in case of any severity events with a subject specified in subject field and will contain the message field's content as the email body. These fields are not applicable for 'AMI-Format' email users.

Note: Email address for the user should be configured under Settings > User Management.

Save: Saves a new entry to the device.

Delete: Deletes the selected configured LAN Destination.

Procedure

1. In the LAN Destinations page, choose the number of slots to be configured. This should be the same number of slot that you have selected in the Alert Policies - Destination Selector field. That is if you have chosen the Destination Selector as 4 in the Alert Policies page of Alert Policies tab, then you have to configure the 4th slot of LAN Destination page.

2. Select the slot and click on the empty slot. This opens the LAN Destination entry.

3. In the LAN Channel Number field, the LAN Channel Number for the selected slot is displayed and this is a read only field.

4. In the LAN Destination field, the destination for the newly configured entry is displayed and this is a read only field.
5. In the Destination Type field, select the one of the types.
6. In the SNMP Destination Address field, enter the destination address.
7. If the destination type is Email alert, select the BMC User Name from the list of users.

Note: E-mail address should be configured under Settings > User Management.

1. In the Email Subject field, enter the subject.

2. In the Email Message field, enter the message.

3. Click Save to save the new LAN destination and return to LAN destination list.

4. Click Delete to delete a configuration.
5. Click Send Test Alert to send sample alert to configured destination.

Note: Test alert can be sent only with enabled SMTP configuration. SMTP support can be enabled under Settings > SMTP Settings.

2-6-11 Services

This page displays the basic information about services running in the BMC. Only Administrator can modify the service.

To open Services page, click Settings > Services from the menu bar. A sample screenshot of Services page is shown below.

MEGARAC SP-X 12.01.38 A/PS 2021 MEGARAC SP-X Hot Online Quick Online... Dashboard Server System Inventory File Information Logic & Resources Settings Remode Control Intelligent Hardware Power Control Maintenance sign out Services Service Status Interfaces Han Secure Port Secure Port Tirenet Maximum Sessions web Active bonell 85 441 3800 20 = ✓ knots Active scale## 7478 7982 3800 2 = ✓ col-media Active bonell 5139 5114 N/A 3 = ✓ NHL-vesella Active scale## 5113 5117 N/A 3 = ✓ zsh Active N/A N/A 23 600 N/A = ✓

The fields in the Services page are explained below.

Services: Displays service name of the selected slot (read-only).

Status: Displays the current status of the service, either active or inactive state.

Interfaces: It shows the interface in which service is running.

Nonsecure Port: This port is used to configure non secure port number for the service.

• Web default port is 80.
  • KVM default port is 7578.
  • CD Media default port is 5120.
  • HD Media default port is 5123.

Note: SSH service will not support non secure port. If single port feature is enabled, M, CD Media, and HD Media ports cannot be edited. Port value ranges in 1 to 65535.

Secure Port: This port is used to configure secure port number for the service.

• Web default port is 443.
  • KVM default port is 7582.
  • CD Media default port is 5124.
  • HD Media default port is 5127.
• SSH default port is 22.

Note: Telnet Port 80 is blocked for TCP/UDP protocols.

value ranges from 1 to 65535.

Port listening status on various feature settings:

	Single port enabled	Single port disabled	Only KVM encryption enabled	Only Media encryption enabled	Both KVM and Media encryption enabled
Adviser (video server)	7578 (LP)	7578 (LP) 7578 (EO)	7578 (LP) 7578 (EO)	7578(LP) 7578 (EO)	7578(LP) 7582 (EO)
Cdserver 5120	(LP)	5120 (LP) 5120 (EO)	5120 (LP) 5120 (EO)	5120 (LP) 5124 (EO)	5120 (LP) 5124 (EO)
Hdserver 5123	(LP)	5123 (LP) 5123 (EO)	5123 (LP) 5123 (EO)	5123 (LP) 5127 (EO)	5123 (LP) 5127 (EO)

Note: LP - Loopback, EO - Exposed Outside.

The adviser will always be listening to loopback as well as kvm configured interface as mentioned in the above table. So that the H5Viewer client can connect to the video server.

The media servers will be listening to loopback as well as configured interface as mentioned in the above table. So that the lmedia/rmedia and H5Viewer/JViewer client can connect to the media servers.

Timeout: Displays the session timeout value of the service. Users can configure the session timeout value.

Note: Web timeout value ranges from 300 to 1800 seconds.

KVM timeout value ranges from 300 to 1800 seconds.

Web timeout value can be ignored if there is any ongoing KVM session.

SSH timeout value ranges from 60 to 1800 seconds.

Maximum Sessions: Displays the maximum number of allowed sessions for the service.

Save: Saves the configuration.

Service Sessions

The Service Sessions page is used to view the current active sessions for the service.

Procedure to open Service Sessions

1. Click the View icon to view the details about the active sessions for the service.

MEGARAC SP-X 12.04.08 AVERAGE SERVICES EPC Open Offline Quick Service Outperform Server Systems Inventory File Information Logic & Projects Settings Remote Control Insight/Indirective Power Control Maintenance Sign out Services Service 0 Status 0 interfaces 0 Han Secure Part 0 Security Part 0 Tavout 0 Modemnt Solutions 0 web Active serverB 80 441 3606 20 link Active loadB 7178 7042 5608 2 cell antennas Active loadB 5129 5124 NA 3 cell assets Active loadB 5110 5117 NA 3 cell Active N/A NA 23 690 NA = ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓

1. This opens the Service Session screen (for example - Web service sessions) as shown in the screenshot below.

MEGARAC SP-X 12.04.08 API & 2023/NEGARAC SP-X + User Online Quick access... InstallShield Server Synnex Inventory File Information Logic & Resources Settings Network Control Image Mechanical Power Control Maintenance Single-mail Service Sessions Active Session - Web Server ID: 0 Server Type: 0 User ID: 0 User Name: 0 Class ID: 0 Privilege: 0 ID: Web HTTPS 2 admin: 209.74.201.003 Administrator ID: Web HTTPS 2 admin: 209.74.201.003 Administrator ID: Web HTTPS 2 admin: 209.74.201.003 Administrator

Session ID: Displays the ID of the active sessions.

Session Type: Displays the type of the active sessions.

User ID: Displays the ID of the user.

User Name: Displays the name of the user.

Client IP: Displays the IP addresses that are already configured for the active sessions.

Privilege: Displays the access privilege of the user.

Procedure to modify the existing services

1. Select a slot and click Edit icon to modify the configuration of the service.

Note: Whenever the configuration is modified, the service will be restarted automatically. has to close the existing opened session for the service if needed.

MEGARAC SP-X ELELAR AUY'S 2021 MEGARAC SP-X Host Online Quick Links Outboard Semner Systems Inventory Fits Information Logic & Resources Settings Remode Central Insight Medium/Global Power Control Maintenance Tags out Services Service Status Interfaces Han Secure Port Secure Port Tireout Treadment Services web Active ScoreB 80 447 3800 20 lows Active ScoreB 79TB 7582 3800 2 cell-media Active ScoreB 5139 5114 N/A 3 Nan-nexela Active ScoreB 5118 5117 N/A 2 zds Active N/A N/A 23 600 N/A ✓

1. This opens the Service Configuration screen as shown in the screenshot below.

NEGARAC SP-X 12.01.38 AUY 2013 NEGARAC SP-X Host Online Quick Limits... Outperform Server System Inventory File Information Log & Reports Settings Remode Control Voltage Modestries Power Control Maintenance Sign out Service Configuration Service Hanks Teams: Active Interface Hanks band0 Non-secure part: 88 Secure part: 445 Threshold: 2009 Maintenance Residors: 26 Save URL - English Type: Refresh Admins Name : Settings Services Service Configuration

1. The Service Name filed is read-only.
2. Check the Active check box to activate the service.

Note: Interfaces, Non-secure port, Secure port, Time out and Maximum Sessions will not give unless the current state is active.

1. Select an available interface in the Interface Name field.
2. Enter the Non-secure Port Number in the Non-secure Port field.

3. Enter the Secure Port Number in the Secure Port field.

4. Enter the timeout value in the Timeout field.

Note: The values in the Maximum Sessions field cannot be modified.

1. Click Save to save all changes you have made.

2-6-12 SMTP Settings

Simple Mail Transfer Protocol (SMTP) is an Internet standard for electronic mail (e-mail) transmission across Internet Protocol (IP) networks.

Using MegaRAC GUI, you can configure the SMTP settings of the device.

To open SMTP Settings page, click Settings > SMTP Settings from the menu bar. A sample screenshot of SMTP Settings page is shown below.

MEGARAC SP-X MELER AFY 2001-2003-2004 Host Online Quick Links DeepReward Service System inventory FWS Information Logic & Requests Settings Remote Control Usage Mechanical Primary Control Web-Demancer Sign out SMTP Settings LAK Interface Sarado Sender Email ID Primary SMTP Support Primary Server Name: Primary Server IP Primary SMTP port: 25 Primary Secure SMTP port: 465 Primary SMTP Authorization Primary Maintenance Primary Password: Primary SMTP SSLTLS Enable Primary SMTP STARTTLS Enable Secondary SMTP Support Secondary Server Name: Secondary Server IP Secondary SMTP port: 25 Secondary SMTP Secure port: 465 Secondary SMTP Authentication Secondary UserName: Secondary Password: Secondary SMTP SSLTLS Enable Secondary SMTP STARTTLS Enable USEN

The fields in the SMTP Settings page are explained below.

LAN Interface: Displays the list of LAN channels available.

Sender Email ID: A valid 'Sender Address' to indicate the BMC, whenever e-mail is sent.

Primary SMTP Support: Enables/Disables SMTP support for the BMC.

Primary Server Name: The 'Machine Name' of the BMC, from where the e-mail is sent.

Note: Machine Name is a string of maximum 25 alpha-numeric characters.

Space, special characters are not allowed.

Primary Server IP: The IP address of the SMTP Server. It is a mandatory field.

Note: IP Address made of 4 numbers separated by dots as in "xxx.xxx.xxx.xxx".

Each Number ranges from 0 to 255.

First Number must not be 0.

Supports IPv4 Address format and IPv6 Address format.

Primary SMTP Port: Specifies the SMTP Normal Port.

Note: Default Port is 25, and the Port value ranges from 1 to 65535.

Primary Secure SMTP Port: Specifies the SMTP Secure Port.

Note: Default Port is 25, and the Port value ranges from 1 to 65535.

Primary SMTP Authentication: Enables/Disables SMTP Authentication.

Note: SMTP Server Authentication Types supported are:

- LOGIN

- PLAIN

If the SMTP server does not support any one of the above authentication types, the user will get an error message stating "Authentication type is not supported by SMTP Server."

Primary Username: Enter username to access SMTP Accounts.

Note: User Name can be of length 4 to 64 alpha-numeric characters, dot(.), dash(-), and underline(_) .

It must start with an alphabet.

Other special characters are not allowed.

Primary Password: Enter password for the SMTP User Account.

Note: Password must be at least 4 characters long.

Blank space is not allowed.

This field will not allow more than 64 characters.

Primary SMTP SSLTLS Enable: Enables SSLTLS support for the SMTP Client.

Primary SMTP STARTTLS Enable: Enables STARTTLS support for the SMTP Client.

- Upload SMTP CA Certificate File: File that contains the certificate of the trusted CA certs. CACERT key file should be of pem type,LOGIN

- Upload SMTP Certificate File: Client certificate filename. CERT key file should be of pem type.

- Upload SMTP Private Key: Client private key filename. SMTP key file should be of

pem type.

Note: To enable STARTTLS support, the respective SMTP support option should be enabled.

Secondary SMTP Support: It lists the Secondary SMTP Server configuration. It is an optional field. If the Primary SMTP server is not working fine, then it uses Secondary SMTP Server configuration.

Note: Options of Secondary SMTP Support are same as Primary SMTP Support.

Save: Saves the new SMTP server configuration.

Procedure

1. Select the LAN Interface from the drop-down list.
2. Enter the Sender Email ID in the specified field.
3. Check Primary SMTP Support option to enable SMTP support for the BMC.
4. Enter the Machine Name of the SMTP Server in the Primary Server Name.

Note: Machine Name is a string of maximum 25 alpha-numeric characters.

Spaces and special characters are not allowed.

1. Enter IP address of the SMTP Server in the Primary Server IP field. It is a mandatory field.
2. Enter the Primary SMTP Port in the specified field.
3. Enter the Primary Secure SMTP Port in the specified field.
4. Check to enable Primary SMTP Authentication if you want to authenticate SMTP Server.
5. Enter your Primary Username and Primary Password in the respective fields.
6. Enable the check box Primary SMTP SSLTLS Enable to send data through secure Port.

Note: If this option is selected, STARTTLS option and Normal Port will be hidden.

1. Check the Secondary SMTP Support option to enable Secondary SMTP support for the BMC.
2. Enter the Secondary Server Name, Secondary Server IP, Secondary SMTP Port and Secondary SMTP Secure Port in the specified fields.
3. Check to enable Secondary SMTP Server Authentication if you want to authenticate SMTP Server.
4. Enter your Secondary Username and Password in the respective fields.
5. Check to enable Secondary SMTP SSLTLS to send data through secure Port.

Note: If this option is selected, STARTTLS option and Normal Port will be hidden.

1. Click Save to save the entered details.

2-6-13 SSL Settings

The Secure Socket Layer protocol was created by Netscape to ensure secure transactions between web servers and browsers. The protocol uses a third party, a Certificate Authority (CA), to identify one end or both end of the transactions.

Using MegaRAC GUI, configure SSL certificate into the BMC. Using this, the device can be accessed in a secured mode.

To open the SSL Certificate Configuration page, click Settings > SSL Settings from the menu bar. There are three tabs in this page.

NEGARAC SP-X 13.01.30 44.5.2001/2006/07/06 View Offline SOSING PROSL Default Board Server Symbol inventory File information Logo & Impacts Settings Nintendo Control Image-Reference Power Controls Maintenance High-out SSL Settings New SSL certificate Deviate SSL certificate Quick SSL certificate

The fields in the SSL Settings page are explained below.

View SSL Certificate: Displays the uploaded SSL certificate's information.

Generate SSL Certificate: Generates the SSL certificate based on configuration details.

Upload SSL Certificate: Uploads SSL certificate in readable format.

View SSL Certificate

A sample screenshot of View SSL Certificate page is shown below.

MEGARAC SP-X CEROL NEW DREAMERS VFC View Info View SSL Certificate Current Certificate Information Certificate Review: ) Build Number 12/09/2016 (A) (A) (B) (C) (D) (E) (F) (G) (H) (I) (J) Registration Algorithm on L2004587043 Recognition Public Key (2014-04) Issuer Account Name: CNL engarac.com Issuer Organization (U) American Government sector (USA) LLC (UK) Issuer Organization (UK) (UK) Service Processors Issuer City or Locality (C) Services Issuer State or Ministry (DE) Services Issuer Country (C) US Issuer Text Address [e-mail] Mail Form AU 13 18.10.2017 2011 GMT Mail Link AU 13 18.10.2017 2011 GMT Issued for Candidates Market (UK) imagarc.com Issued for Certification (U) American Government International LLC (UK) Issued for Certification staff (DE) Service Processors Issued for City or Locality (C) Incorporated Issued for Market or Preference (DE) George Issued for County (C) US Issued for Email Address [e-mail]

The fields in the View SSL Certificate page are explained below.

Current Certificate Information: This section displays the basic information about the uploaded SSL certificate. It displays the following fields:

• Certificate Version
• Serial Number
• Signature Algorithm
  • Public Key
• Issuer Common Name (CN)
• Issuer Organization (O)
• Issuer Organization Unit (OU)
• Issuer City or Locality (L)
• Issuer State or Province (ST)
• Issuer Country (C)
• Issuer E-mail Address

• Valid From

• Valid Till

• Issued to Common Name (CN)
• Issued to Organization (O)
  • Issued to Organization Unit (OU)
• Issued to City or Locality (L)
• Issued to State of Province (ST)
• Issued to Country (C)
• Issued to Email Address

Generate SSL Certificate

A sample screenshot of Generate SSL Certificate page is shown below.

MEGARAC SP-X C:\SP-X\GENEER\SPX\GENEER\SPX + New Email Generate SSL Certificate Customer License (C) Organizers (R) Organizers Unit (U) City of Locality (C) State or Privatock (S) Covality (C) Address Address Markit No. In-Print Buy Length J044 bits USE

The fields in the Generate SSL Certificate page are explained below.

Common Name (CN): Common name for which certificate is to be generated.

• Maximum length of 64 characters.
- It is a string of alpha-numeric characters.
- Special characters '#' and '\$' are not allowed.

Organization (O): Organization name for which the certificate is to be generated.

• Maximum length of 64 characters.
- It is a string of alpha-numeric characters.
- Special characters '#' and '\$' are not allowed.

Organization Unit (OU): Over all organization section unit name for which certificate is to be generated.

• Maximum length of 64 characters.
- It is a string of alpha-numeric characters.
- Special characters '#' and '\$' are not allowed.

City or Locality (L): City or Locality of the organization (mandatory).

• Maximum length of 128 characters.
- It is a string of alpha-numeric characters.
- Special characters '#' and '\$' are not allowed.

State or Province (ST): State or Province of the organization (mandatory).

• Maximum length of 128 characters.
- It is a string of alpha-numeric characters.
- Special characters '#' and '\$' are not allowed.

Country (C): Country code of the organization (mandatory).

• Only two characters are allowed.
• Special characters are not allowed.

Email Address: E-mail Address of the organization (mandatory).

Valid for: Validity of the certificate.

• Value ranges from 1 to 3650 days.

Key Length: The key length bit value of the certificate.

Save: Generates the new SSL certificate.

Note: HTTPS service will get restarted, to use the newly generated SSL certificate.

Upload SSL Certificate

A sample screenshot of Upload SSL Certificate page is shown below.

MEGARAC SP-X NEW YORK New York 2021 NEW YORK Quick Online Upload Draftboard Server Hyperlink Inventory File Information Logic & Resources Settings Remote Control Intangible Data Power Control Maintenance Sign out Upload SSL Certificate Current Certificate Tue Jul 13 18:52:00 2021 New Certificate Current Private Key Tue Jul 13 18:52:00 2021 New Private Key Save

The fields in the Upload SSL Certificate page are explained below.

Current Certificate: Current certificate and uploaded date/time will be displayed (read-only).

New Certificate: Browse the new certificate file. The certificate file should be of pem type.

Current Private Key: Current Private key information will be displayed (read-only).

New Private Key: Browse the new private key. The private key file should be of pem type.

Save: Uploads the SSL certificate and privacy key into the BMC.

Note: After successful upload, HTTPS service will restart to use the newly uploaded SSL certificate.

Procedure

1. Click the Upload SSL Certificate tab, browse the New Certificate and New Private key.
2. Click Save to upload the new certificate and private key.

3. In Generate SSL Certificate, enter the following details in the respective fields:

4. The Common Name for which the certificate is to be generated.

5. The Organization for which the certificate is to be generated.

6. The Organization Unit name for which certificate to be generated.
   • The City or Locality of the organization
   • The State or Province of the organization
   • The Country of the organization
   • The Email address of the organization.
   • The number of days the certificate will be valid in the Valid For field.

7. Choose the Key Length bit value of the certificate

8. Click Save to generate the certificate.
9. Click View SSL Certificate tab to view the uploaded SSL certificate in user readable format.

Note: Once you Upload/Generate the certificates, only HTTPS service will get restarted. I can now access your Web securely using the following format in your IP Address

field from your Internet browser: https:// For example, if your BMC's IP address is 192.168.0.30, enter the following:

https://192.168.030

Please note the after . You must accept the certificate before you are able to access your Web.

2-6-14 System Firewall

In MegaRAC GUI, the System Firewall page allows you to configure the firewall settings. The firewall rule can be set for an IP or range of IP Addresses or Port numbers. To view this page, you must at least be an operator. Only administrators can add or delete a firewall.

To open System Firewall page, click Settings > System Firewall from the menu bar.

MEGARAC SP-X 12.01.38 AVS 2021 MEGARAC SP-X Hot Online Quick Links... Dashboard Server System Inventory File Information Logic & Reports Settings Remode Control Intelligent Broadcast Power Control Maintenance Sign out System Firewall General Firewall Settings IP Additional Firewall Rules Port Firewall Rules USE - English Topic Refresh Admins Name Settings Open/Forward

General Firewall Settings

Click General Firewall Settings page. A sample screenshot of General Firewall Settings page is shown below.

NEGARAC SP-X BLUE Server AVEN 2013 PROWEED EPC File Online Quick Lines... Dustboard Sensor Instruments inventory File Information Logis & Reporters Settings Remote Control Usage Devices Power Control Maintenance Tags out General Firewall Settings + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -

The fields in the Firewall Settings page are explained below.

Existing Firewall Settings

Click General Firewall Settings > Existing Firewall Settings icon. A blank page will be opened if you did not add anything in Add Firewall Settings. If any settings are added, then the added rule will be listed in Existing Firewall Settings page. A sample screenshot of Existing Firewall Settings page is shown below.

MEGARAC SP-X 13.91.33 Aug 12 2015 04:21:01 UTC © New Office Quick Links... Dashboard Sensor System Inventory FRII Information Logs & Reports Settings Remote Control Image Redirection Power Control Maintenance Sign out 2015-04-03 23:56:13 (UTC+40:00 GMT) Existing Firewall Settings Block All: IPv4 Timeout: Enabled Points Set Aug 22 2021 17:16:00 To: Set Aug 21 2021 21:28:00 US - English Sync Refresh admin - Home - Settings - Firewall - General Firewall Settings - Existing Firewall Settings

The Existing Firewall Settings page allows you to remove any particular Existing Firewall Settings.

Procedures

1. Select the Existing Firewall Settings you want to remove.
2. Click on Delete to remove the selected Existing Firewall Settings.

MEGARAC SP-X 13:01:33 Aug 12 2021 08 21:01 UTC © New Office Quick Links. Dashboard Sensor System Inventory FRU Information Sell Logs & Reports Settings Remote Control Image Redirection Power Control Maintenance Sign out Existing Firewall Settings Block All IPv4 Phosh All Timeout Start Date&Time Sat Aug 21 2021 17:19:00 End Date&Time Sat Aug 21 2021 21:00:00 Delete US - English Sync Refresh admin Name - Settings - Firewall - General Firewall Settings - Existing Firewall Settings - Funding Firewall Settings

Add Firewall Settings

Click General Firewall Settings > Add Firewall Settings. This opens the Add Firewall Settings page as shown below.

NEGAURC SP.X ADD NEW BREAKS VEN Add Existing Add Firewall Settings Block All Push Flush All Networks Start Subs Enter All Subs Start Time Grid Date Enter Subs Grid Time Save

Procedures

1. Select Block All to block all the incoming IP's and Port's.
2. Select Flush All to flush all the system firewall rules.
3. Select Timeout to enable or disable firewall rules with timeout.
4. Enter Start Date to start the respective firewall rule effect from this date.
5. Enter Start Time to start the respective firewall rule effect from this time.
6. Enter End Date to end the respective firewall rule effect from this date.
7. Enter End Time to end the respective firewall rule effect from this time.
8. Click Save to save the changes made.

IP Address Firewall Rules

Click IP Firewall Rules page. A sample screenshot of IP Firewall Rules page is shown below.

NEGARAC SP-X C:\EEL\MAY 2021 NEW築籤\IFC Host Online Quick Limits... Dustboard Sensor Symbols Inventory File Information Logs & Reposets Settings Bemends Control Image Manufacturing Power Control Maintenance Sign out IP Firewall Rules Existing IP Rules Add/Remove IP Rule US - English Topic Refresh Admins Home Settings Ferewith IP Firewall Rules

The fields in the IP Address Firewall page are explained below.

Existing IP Rules

To view Existing IP Rules, click Settings > System Firewall > IP Address Firewall Rules > Existing IP Rules. A blank page will be opened if you did not add anything in Add IP Rule. If any rule is added, then the added rule will be listed in Existing IP Rules page.

A sample screenshot of Existing IP Rules page is shown below.

MEGARAC SP-X 13.01.03 Aug 12 2021 08:20:01 UTC © Host Office Quick Links... Dashboard Sensor System Inventory FISU Information Logs & Reports Settings Remote Control Image Redirection Power Control Maintenance Sign out 2021-04-02 22:58:00 (UTC+80:00 GMT) US - English Sync Refresh admin - Existing IP Rules IP / IP Range: 10.1.T,100 - 10.1.T,200 Rule: Allure Timeout: Enabled From: Saturday, August 21st 2021, 9:23:00 am. To: Saturday, August 21st 2021, 2:23:00 pm

The Existing IP Rules page allows you to remove any particular Existing IP Rules.

Procedure

1. Select the Existing IP Rules you want to remove.
2. Click on Delete to remove the selected Existing IP Rules.

MEGARAC SP-X 13.06.33 Aug 02 2021 18:21:00 UTC About 05/00 Quick Links... Dashboard Sensor System Inventory FRU Information Logs & Reports Settings Remote Control Image Redirection Power Control Maintenance Sign out 2021-04-03 12:58:31 (UTC=00.06 GMT) US - English Sync Rebeach admin- Existing IP Rules IP Single (or) Range Start 10.1.7.100 IP Range End 10.1.7.200 Enable Timeout Start Dates&Time Saturday, August 21st 2021, 9:23:00 am End Dates&Time Saturday, August 21st 2021, 2:23:00 am Rule Allion Delete

IP Single (or) Range Start: Shows the configured Port Address or Range of Ports.

IP Range End: Shows the configured Port Address or Range of Ports.

Enable Timeout: Enables/Disables Timeout.

Start Date: The respective firewall rule effect will start from this date.

Start Time: The respective firewall rule effect will start from this time.

End Date: The respective firewall rule effect will end from this date.

End Time: The respective firewall rule effect will end from this time.

Rule: Indicates the current setting of the listed Port or Range of Port rules (Allow or Block) status.

Delete: Deletes the selected slot.

Add IP Rule

To add a new IP rule, click Settings > System Firewall > IP Address Firewall Rules > Add New IP Rule. If any rule is added, then the added rule will be listed in Existing IP Rules page.

A sample screenshot of Add IP Rule page is shown below.

NEGARAC SPX C:\Users\NAY PREMERSIONS EPC Start Ending Quick Links DefaultReport Sensor System Inventory My Information Logic & Requests Settings Remarks Control Image Hardware Power Control Maintenance Sign out Add IP Rule IP Single (or) Range Start IP Range End systemed Available Threshold Start Rule: Start Date: End Date: End Time: Rule: Alose Save Name Settings Format IP Created Software Tools Help IP Rule

Procedure

1. In the Add IP Rule page, enter the IP address and a range of IP addresses in the IP Single or IP Range Start field.

Note: IP Address will support IPv4 Address format only:

TPv4 Address made of 4 numbers separated by dots as in xxx.xxx.xxx.xxx.

Each number ranges from 0 to 255.

First number must not be 0.

1. Enter IP range end value in the IP Range End field.
2. Enable Timeout to enable firewall rules with timeout.
3. Enter Start Date to start the respective firewall rule effect from this date.
4. Enter Start Time to start the respective firewall rule effect from this time.
5. Enter End Date to end the respective firewall rule effect from this date.
6. Enter End Time to end the respective firewall rule effect from this time.

Note: The date and time should be in the YYYY/MM/DD and hh-mm format respectively.

1. Determine the rule to block or accept.
2. Click Save to save the changes made.

Port Firewall Rules

Click Port Firewall Rules page. A sample screenshot of Port Firewall Rules page is shown below.

MEGARAC SP-X URL: 2021-07-23 14:38:56 [LITCH-00080-0047] Port Firewall Rules Building Port Rules Add New Rule Rule

Existing Port Rules

To view Existing Port Rules, click Settings > System Firewall > Port Firewall Rules > Existing Port Rules. A blank page will be opened if you did not add anything in Add New Port Rule. If any rule is added, then the added rule will be listed in Existing Port Rules page.

A sample screenshot of Existing Port Rules is shown below.

BMC Firmware Information 2.78.300227 Jan 28 2019 10:44:04 EST + Quick Order Quick Links... Dashboard Sensor System Inventory FRU Information Logs & Reports Settings Remote Control Image Redirection Power Control Maintenance Sign out 2019-04-07 20:34:42 (UTC-11:30 UTC) Existing Port Rules Port / Port Range: 123 - 476 Prentool: TCP Network Type: IPy4 Allow Firmout: Ex&lMad From: 2019-04-07 20:33:00 (UTC-11:00 UTC) To: 2019-04-26 21:33:00 (UTC-11:30 UTC) Home - Settings - Forward - Port Drivened Firewall Rules - Existing Port Rules

Procedure

1. Select the Existing Port Rules you want to remove.
2. Click on Delete to remove the selected Existing Port Rules.

BMC Firmware Information 2.76.300227 Jan 28 2015 10:48-04 CST Wind Drive Quick Links... Dashboard Sensor System Inventory FRU Information Logo & Reports Settings Remote Control Image Redirection Power Control Maintenance Sign out Existing Port Rules Port Single (or) Range Start 123 Port Range End 458 Protocol TCP Network Type IPyA Enable Timeout Start Date&Time 2019-04-07 20:33:00 (UTC-11:30 UTC) End Date&Time 2019-04-25 21:33:00 (UTC-11:30 UTC) Rule Allow Delete

The fields in the Existing Port Rules page are explained below.

Port Single (or) Range Start: Configures the Port or Range of Port Addresses.

Port Range End: Configures the Port or Range of Port Addresses.

Protocol: This field specifies the protocols for the configured Port or Port Ranges.

Network Type: This field specifies the affected network type for the particular Port or Port

Ranges.

Enable Timeout: Enables/Disables firewall rules with timeout.

Start Date: The respective firewall rule effect will start from this time.

Start Time: The respective firewall rule will start from this time.

End Date: The respective firewall rule effect will end on this date.

End Time: The respective firewall rule will end at this time.

Rule: Indicates Allow or Block status.

Delete: Deletes the entry to the firewall rules list.

Add New Port Rule

To add a new port rule, click Settings > System Firewall > Port Firewall Rules > Add New

Port Rule. A sample screenshot of Add New Port Rule is shown below.

MEGARAC SP-X NEW NELL MINDS-INFO Host Online Quick Links... DeepMandard Service System Inventory FPU Information Logic & Resources Settings Services Control Usage Infrastructure Power Control Maintenance Sign out Add Port Rule Port Single (or) Range Start Port Range End optional Protocol: TCP Network Type: iOS Enable "Transport" Start Rule: engguanapp Start Title: End Date: engguanapp End Time: Rule: Allow: Home Settings Password Port Drivened Passoff Rules Make/Use Rule

Procedure

1. In the Port Single (or) Range Start field, enter the port number or a range of port addresses.

Note: Port value ranges from 1 to 65535.

80 is blocked for TCP/UDP protocols.

1. Enter the end value in the Port Range End field.
2. Select the Protocol to be either TCP or UDP or Bot.
3. Select the Network Type. It may be IPv4 or IPv6 or Both.
4. Check/uncheck Enable Timeout to enable/disable firewall rules with timeout.
5. Enter Start Date to start the respective firewall rule effect from this date.
6. Enter Start Time to start the respective firewall rule effect from this time.
7. Enter End Date to end the respective firewall rule effect on this date.
8. Enter End Time to end the respective firewall rule effect at this time.

Note: The time should be in the YYYY/MM/DD:hh-mm format.

1. Select either Block or Allow in the Rule field.
2. Click Save to save the changes made.

2-6-15 User Management

In MegaRAC GUI, the User Management page allows you to view the current list of user slots for the server. You can add a new user and modify or delete the existing users.

To open User Management page, click Settings > User Management from the menu bar. A sample screenshot of User Management page is shown below.

MEGARAC SP-X USER NEW BUSINESS EPIC Host Online Quick Links... Dashboard Sensor Systems Inventory File Information Logic & Repurchase Settings Bemers Control Usage Realdehyde Power Control Maintenance Sign out User Management Channel 1 1. Interpersonal (Disabled) No Acclose Pure, Unadded Channel 1 2. Adelta (Disabled) Administrator Post "PAGE" Channel 1 3. (Disabled) Channel 1 4. (Disabled) Channel 1 5. (Disabled) Channel 1 6. (Disabled) Channel 1 7. (Disabled) Channel 1 8. (Disabled) Channel 1 9. (Disabled) Channel 1 10. (Disabled) Channel 1 11. (Disabled) Channel 1 12. (Disabled) Channel 1 13. (Disabled) Channel 1 14. (Disabled) Channel 1 15. (Disabled) Channel 1 16. (Disabled) Channel 1 17. (Disabled) Channel 1 18. (Disabled) Channel 1 19. (Disabled) Channel 1 20. (Disabled) Channel 1 21. (Disabled) Channel 1 22. (Disabled) Channel 1 23. (Disabled) Channel 1 24. (Disabled) Channel 1 25. (Disabled) Channel 1 26. (Disabled) Channel 1 27. (Disabled) Channel 1 28. (Disabled) Channel 1 29. (Disabled) Channel 1 30. (Disabled) Channel 1 31. (Disabled) Channel 1 32. (Disabled) Channel 1 33. (Disabled) Channel 1 34. (Disabled) Channel 1 35. (Disabled) Channel 1 36. (Disabled) Channel 1 37. (Disabled) Channel 1 38. (Disabled) Channel 1 39. (Disabled) Channel 1 40. (Disabled) Channel 1 41. (Disabled) Channel 1 42. (Disabled) Channel 1 43. (Disabled) Channel 1 44. (Disabled) Channel 1 45. (Disabled) Channel 1 46. (Disabled) Channel 1 47. (Disabled) Channel 1 48. (Disabled) Channel 1 49. (Disabled) Channel 1 50. (Disabled) Channel 1 51. (Disabled) Channel 1 52. (Disabled) Channel 1 53. (Disabled) Channel 1 54. (Disabled) Channel 1 55. (Disabled) Channel 1 56. (Disabled) Channel 1 57. (Disabled) Channel 1 58. (Disabled) Channel 1 59. (Disabled) Channel 1 60. (Disabled) Channel 1 61. (Disabled) Channel 1 62. (Disabled) Channel 1 63. (Disabled) Channel 1 64. (Disabled) Channel 1 65. (Disabled) Channel 1 66. (Disabled) Channel 1 67. (Disabled) Channel 1 68. (Disabled) Channel 1 69. (Disabled) Channel 1 70. (Disabled) Channel 1 71. (Disabled) Channel 1 72. (Disabled) Channel 1 73. (Disabled) Channel 1 74. (Disabled) Channel 1 75. (Disabled) Channel 1 76. (Disabled) Channel 1 77. (Disabled) Channel 1 78. (Disabled) Channel 1 79. (Disabled) Channel 1 80. (Disabled)

The fields in the User Management page are explained below.

Note: The free slots are shown as "Disabled" in all columns for the slot.

User ID: Displays the ID number of the user.

Note: The list contains a maximum often users only.

User Name: Displays the name of the user.

User Access: Enables/Disables the access privilege of the user.

Network Privilege: Displays the network access privilege of the user.

SNMP Status: Displays if the SNMP status for the user is enabled or Disabled.

E-mail ID: Displays e-mail address of the user.

Add User: Adds a new user.

Delete User: Deletes an existing user.

MEGARAC SPX ASP.NET ASP.NET PROGRESSIVE VEC User Interface Check Links... Defaultset Session Updated Inventory USB Information Log & Request Settings Remote Central Image-Indemise Power Controls MultiResources Sign All User Management Configuration Userlisters amorphisms Change Password Password/Title If Bytes Password: Default set Passenger 8 Enable User Access Enable Channel Access Channel 1 Channel 1 Privilege Channel 1) Issue Privilege Channel 2) Administrator XML access VMOS Access SMTP Access SMTP Access level SMTP Authentication Preferred SMTP Privacy Protocol Email Former Add Format Email ID: Existing SMTP Key Use shareable Upload SMTP Key Cancel Help Name: Settings - User Management - User Management Configurations

Procedure

1. To add a new user, select an empty slot on the User Management page. The User Management Configuration screen will appear,
2. Enter user name in the Username field.

Note: User name is a string of 1 to 16 alpha-numeric characters.

It must start with an alphabetical character and it is case-sensitive.

Special characters '-'(hyphen), '-' (underscore), '@'(at sign) are allowed.

For 20 Bytes password, LAN session will not be established.

1. Check Change Password if you want to change the password.
2. Set Password Size for the new password.
3. In the Password and Confirm Password fields, enter and confirm the password.

Note: Password should be the combination of alphabets, numbers, symbol and upper characters.

Blank space is not allowed.

This field will not allow more than 16/20 characters based on Password size field value.

This field will not allow the below mentioned characters.

The password should be a string, if you try to set password using "ipmitool user set password".

Hex Char
00 NUL '\0'
01 SOH (start of heading)
02 STX (start of text)
03 ETX (end of text)
04 EOT (end of transmission.)
05 ENQ (enquiry)
06 ACK (acknowledge)
07 BEL '\a' (bell)
08 BS '\b' (backspace)
09 HT '\t' (horizontal lab)
0A LF '\n' (new Line)
0B VT '\v' (vertical tab)
0C FF '\f' (form feed)
0D CR '\r' (carriage ret)
0E SO (shift out)
0F SI (shift in)
10 DLE (data link escape)
11 DC1 (device control 1 )
12 IDC2 (device control 2)
13 DG3 (device control 3)
14 DC4 (device control 4)
15 NAK (negative ack.)
16 SYN (synchronous idle)
17 ETB (end of trans. blk)
18 CAN (cancel)
19 EM (end of medium)
19 EM (end of medium)
1A SUB (substitute)
1B ESC (escape)
1C FS (file separator)
1D GS (group separator)
1E RS (record separator)
1F US (unit separator)
20 SPACE
7F DEL

1. Enable or disable the Enable User Access.
2. Enable or disable the Enable Channel Access.

Note: Enabling channel access will assign the IPMI messaging privilege to user.

It is recommended that the IPMI messaging option should be enabled as well if user is created through IPMI.

1. In the Privilege (Channel 1) and Privilege (Channel 2) fields, select a privilege level.
2. Check KVM Access to assign the KVM privilege.
3. Check VMedia Access assign the VMedia privilege.

Note: It is recommended that the privileges support to KVM and VMedia should be

provided only to the ADMIN user and shouldn't be provided to USER and OPERATOR privilege level users. The Admin user can provide the privilege support to USER and OPERATOR privilege level users at their own risk.

VMedia Privilege only restricts initiating / starting media redirection. If a device is already being redirected and attached to the host, then in host it will be visible as normal device. Hence, it will be accessible to all the KVM sessions, which includes 'KVM Privilege only' sessions as well.

1. Check SNMP Access to enable SNMP access for the user.

Note: Password field is mandatory, if SNMP is enabled.

1. Choose the SNMP Access level option for user from the SNMP Access level (SHA) drop-down list. Either it can be read-only or read-write.
2. Choose the SNMP Authentication Protocol (SHA) to use for SNMP settings from the drop down list.

Note: Password field is mandatory, if Authentication protocol is changed.

1. Choose the Encryption algorithm to use for SNMP settings from the SNMP Privacy Protocol drop-down list.
2. In the Email ID field, enter the email ID of the user. If the user forgets the password, the new password will be mailed to the configured email address.

Note: SMTP Server must be configured to send emails.

Email Format: Two types of formats are available:

• AMI-Format: The subject of this mail format is 'Alert from (your Host name)'. The mail content shows sensor information, ex: Sensor type and Description.

• Fixed-Subject Format: This format displays the message according to user's setting. You must set the subject and message for email alert.

• The Existing SSH Key field displays information of an existing SSH key.

• In the Upload SSH Key field, click Browse and select the SSH key file.

Note: SSH key file should be of pub type.

1. Click Save to save the new user and return to the users list.

If you need to modify the privilege or information of an existing user, select the user on the User Management page to open the User Management Configuration screen and modify the configurations accordingly.

2-6-16 Video Recording

The Video Recording consists of the following:

1. Auto Video Settings

• Video Trigger Settings
• Video Remote Storage
• Pre-Event Video Recordings

1. SOL Settings

2. SOL Trigger Settings
   • SOL Video Remote Storage

3. SOL Recorded Video

A sample screenshot of the Video Recording is given below.

NEGARAC SP-X 12.03.28 JUL 2013 MEGROS-IFC Host Online Quick URL: Dustboard Server Integrated Inventory File Information Logic & ImageX Settings Remedy Control Language Distribution Power Control Maintenance Sign out 2021-07-22 16:47:37 (JYTC-00:00:00:00) Video Recording Auto/Video Settings BOS Settings US - English Topic Mailtech Admins Home Settings Video Recording

A detailed description of the menu items are given below.

Auto Video Settings

The Auto Video Settings page allows you to configure the events that will trigger auto video recording function of the KVM server and view the current list of user slots for the server. You can add a new user and modify or delete the existing users.

This page is used to configure the events that will trigger auto video recording function of the KVM server.

NEGARAC SP-X TITLE NEW NEELEMECKO-IFC Hot Online Quick Links... Dashboard Server Synthetic Inventory File Information Logic & Impacts Settings Remote Control Usage/Recordbox Power Control Maintenance Sign out 2021-07-22 16:47:59 (UHTD-00380.COMT) US - Engink Autol Supply Settings Video Trigger Settings Index Remote Storage Event Event Video Packings

To triggers for Auto Video Recording, click Video Recording > Auto Video Settings > Video Trigger Settings from the menu bar. A sample screenshot of Video Trigger Settings page is shown below.

MEGARAC SP-X CULS 2023 NOGARAC SPX Use Online Quick Limits... Dust/Border Sensor System Inventory File Information Logic & Monopics Settings Remode Control Usage/Modematics Power Control Maintenance Sign out Video Trigger Settings Critical Events (Temperatures/Volages) Non-Critical Events (Temperatures/Volages) Non-Recoverable Events (Temperatures/Volages) Fan status changed Event Watching Theme Events Chassis Player On Events Chassis Player Off Events Chassis Reset Events LPC Reset Events State and Theme Event Play Event Before Eventing Home Settings Video Advanced Slots Trigger Settings

Video Trigger Settings

Event List: It shows the list of available events to be configured. The events are mentioned below.

• Critical Events (Temperature/Voltage)
• Non Critical Events (Temperature/Voltage)
• Non Recoverable Events (Temperature/Voltage)
• Fan state changed Events
- Watchdog Timer Events
- Chassis Power on Events
- Chassis Power off Events
- Chassis Reset Events
- LPC Reset Events
- Date and Time Event
• Pre-Event Video Recording

Save: Saves the current changes.

Procedure

1. Check the events to be enabled.
2. To set particular date and time event, check the option Date and Time Event.
   a) Choose the month, day and year from the Date field
   b) Enter/Choose the time in hh:mm format in the Time field.

Note: KVM service should be enabled to perform auto-video recording. The date and should be in advance to the system date and time.

1. Click Pre-Event Video Recording to edit the Pre-Event video recording configurations. A sample screenshot of Pre-Event Video Recordings page is shown as below.

NEGARAC SP-X ELELTR AVS 2021 PROSETS EXC Host Online Quick Links... Dashboard Semner System Inventory File Information Logic & Report's Settings Remode Control Inteag/Reductbox Power Control Maintenance Sign out Pre-Event Video Recordings This page is used to configure the pre-event video recording options. Pre-event video recording is highly default. To enable the Pre-event video recording, go to the Windows Configuration page. Refer: Disable to enable pre-event recording selection for newly modified configuration to take effect. Video Quality Very Low Compression Marks High Frames Per Second 1 Video Transition 10 Save Home Settings - Sales Auto settings The Cross Video Recordings

a) To set video quality, select a resolution (Very Low, Low, Average, Normal, High) from the drop-down list of Video Quality.

b) To set compression mode, select a compression mode (high, normal, low, no) from the drop-down list of Compression Mode.
c) To set number of frames per second, select frames/sec (1-4) from the drop-down list of Frames Per Second.
d) To set duration of video, select second (10-60) from the drop-down list of Video Duration.
e) Click Save to save the changes made on Pre-Event Video Recording.

1. Click Save to save the changes made on Video Trigger Settings.

Video Remote Storage

To configure Video Remote Storage, click Video Recording > Auto Video Settings > Video Remote Storage. A Sample screenshot of Video Remote Storage is as shown below.

NEGARAC SP-X 12.08.30 JAY 9 2021 MEXICO-IFC Trust Online Quick Limits... Outboard Server Typobek Inventory File Information Loga & Requests Settings Remedy Control Image Monitoring Power Control Maintenance Sign out Video Remote Storage Record Video to Remate Server Maximani Eventx 2 Maximani Duration (SEC) 26 Maximani Icon (IMR) 5 Shower Address Connect IP or Host Name Push to server reg: Host from childrens Share Type JVS CHS Domain Names Downloadable Password USB US - English Logic Text Web Admins Power Settings - Video - Auto sendings - Video Remote Storage

Procedure

1. Check Record Video to Remote Server to enable the Remote Video Support.

Note: By default, video files will be stored in local path of BMC. If remote video support enabled, the video files will be stored only in remote path, not within BMC.

1. Enter Dumps value of the video in the Maximum Dumps field.
2. Enter maximum duration of the video in the Maximum Duration (Sec) field.
3. Enter maximum size of the video in the Maximum Size (MB) field.

Note: The Maximum Duration of the video should be in the range from 1 to 3600 bonds. The Maximum Size of the video should be in the range from 1 to 500 MB.

The Maximum Dumps should be in the range from 1 to 100. The recorded video file should meet either the size constraint or duration constraint, according to the configured settings, depending on which constraint is met first.

1. Enter the server address in the Server Address field.

Note: Server address will support the following:

Address (Both IPv4 and IPv6 format).

FQDN (Fully qualified domain name) format.

1. Enter the source path in Path in Server field

2. Select the Share Type (NFS/CIFS). If the selected share type is (CIFS), enter the domain name, user name, and password in the Domain Name, Username, Password field respectively.

3. Click Save to save the settings.

Pre-Event Video Recording

Pre-Event Video Recordings is used to configure the Pre-Event video recording options. Pre-Event video is disabled by default. To enable the Pre-Event video recording, go to Settings >Video Recording >Auto Video Settings >Video Trigger Settings.

Pre-Event video recording files will be named as per event captured. For example - if any video is recorded for Crash Event, the recorded file will be named as pre_crash_video_x.dat, where x is file count, similarly if it is recorded for reset event it will be named as pre_reset_video_x.dat.

SOL Settings

To open SOL Set page, click Settings > Video Recording > SOL Settings from the menu bar. A sample screenshot of SOL Settings page is shown below.

NEGARAC SPX BLUEB AVEN PRESTOCKS VIX: Next Options QUICKING... Dashboard Server Systems Inventory Fills Information Logic & Reports Settings Remote Control Image Monitoring Power Control Maintenance Big out 19.2023-07-22 18:52:00 (JYTD-000000049) US - Englink Projects Method Details Name: Settings / Pages: US Settings SQL Settings SQL Trigger Settings SQL Value Settings SQL Received Status

The fields in the SOL Settings page are explained below.

SOL Trigger Settings

The SOL Trigger Settings page shows the list of available events.

• Critical Events (Temperature/Voltage)
• Non Critical Events (Temperature/Voltage)
• Non Recoverable Events (Temperature/Voltage)
• Fan state changed Events
- Watchdog Timer Events
- Chassis Power on Event
- Chassis Power off Event
- Chassis Reset Events
- LPC Reset Events
• Date and Time Events

A sample screenshot of SOL Trigger Settings page is shown as below.

MEGARAC SP-X MELON APR DISTRICTED-SPX Input Edition SOL Trigger Settings Critical Events (Temperature/Settings) Non-Critical Events (Temperatures/Voltage) Non-Personal Events (Temperature/Voltage) Par value changed Events Matching Theme Events Chassis Power Str Events Chassis Power Off Events Chassis Reset Events LPC Reset Events Beta Load Theme Event Save

Procedure

1. Check the events to be enabled to configure which event on the page will trigger the SOL video recording option to start.
2. To set particular Date and Time Event, check the option Date and Time Event.

a) Choose the month, day and year in the Date field.
b) Enter the Time in hh:mm:ss format in the Time field.

Note: The date and time should be in advance to the system date and time.

1. Click Save to save the changes.

SOL Video Settings

This page allows you to configure recorded video files. The sample screenshot and various fields of SOL Video Settings are given below.

MEGARAC SP-X SQL Server MFS (RECOMMENDED VIE) Input IDs SQL Backboard Server Typical Inventory File Information Logic & Resources Settings Tirems Control Image-ReductionBox Power Control Maintenance Login out SOL Video Settings Log Size (R): 326 Log Mix Content: 7 Recorded Videos to Reiterate Review Server Address: Server/For High Name Path to Server log: Web Services Mark Type: NPS OFS Database Market Shareholder Platform(S): Save URL - English Hybrid Network Admins

Procedure

1. Enter the preferred log size in the Log Size (KB) field. The maximum log size supported is 128 KB.
2. Enter log file count in the Log File Count field. The maximum log file count is 1.
3. Check/uncheck Record Video to Remote Server to enable/disable Remote Video support.

Note: By default, video files will be stored in local path of BMC. If remote video support enabled, the video will be stored only in remote path, not within BMC.

1. Enter server address in the Server Address field.

Note: Server address will support the following:

Address (Both IPv4 and IPv6 format).

FQDN (Fully qualified domain name) format.

1. Enter the source path in Path in Server field.

Note: Path must be alpha-numeric and the special characters '-' (hyphen), underscore), '@'(at sign) are allowed.

1. Select the Share Type (NFS/CIFS). If the selected share type is (CIFS), enter the domain name, user name, and password in the Domain Name, Username, Password field respectively.

2. Click Save to save the settings.

SOL Recorded Video

This page displays the list of available recorded video files on the system. Click on Download icon to download and save the video. Click on Delete icon to delete the selected video.

A sample screenshot of SOL Recorded Video is given below.

NEGARAC SP-X ECLX3E AUY 2021 PRODUCS IFC Host Online Quick Links... Qualiforand Semner Systems Inventory File Inferences Logic & Resources Settings Bonds Control Image dimensions Power Control Maintenance Tag out SOL Recorded video S.No # File Name # File Information # Name Settings Sales SQL SOL Recorded Video

2-6-17 Fan Profile

The Fan Profile page allows you to add new fan profile or edit fan profile.

A sample screenshot of the Fan Profile is given below.

NEGARAC SP-X BLUE BY AUY 2023 (MEN) (FIE) + List Delivery Quick Links Lastboard Summer Typical inventory File information Logo & Reports Settings General Control Usage/Modestock Power Control Maintenance Sign out Fan Profile Input Download Manager Target PCV Desiversion + May-fan profile Name: default Status: Song Name: SPS/Gower Status: Run

New Fan Profile

To add new fan profile, click the New fan profile tab.

MEGARAC SP-X MAGULAR ANY INSURANCE & PC 1. Host Privacy Edit New Fan Profile Name: NEW_PROFILE Policy: Algorithm Session Type Initiation Duty 0 Step Temperature 2 200 Sensor Fan Policy Execute Condition CPU/Map (Mb) 0 Accessible Issue: N/A P120 Devio: In each case possible device, ignore this execute condition Policy Reference Table Reference: 0 Entry (%) 247 200 New Options Settings New Profile Edit New Fan Profile Data - Graphs Settings New Profile Edit New Fan Profile

Procedure

1. Name the fan profile in the Name field.
2. Choose the mapping function of temperature and fan speed for the fan profile in the Algorithm field.

3. Select sensory type in the Sensor Type field.

4. Set the fan speed when the system is powering on in the Initialize Duty field.

5. Select the sensor you want to include in this profile in the Sensor field.
6. Select the fan you want to include in this profile in the Fan field.
7. Click New in the Policy Reference Table field to create a new sensor value & fan speed duty mapping table.
8. Set reference temperature and fan speed duty in the Policy Reference Table field.
9. Click Save on the top side to save the configuration.
10. Click the arrow icon to run the fan profile.

NEGARAC SP-X CBL3F JUL 2021 NOCKOS IFC Host Online Quick Links... Outboard Sensor Systems Inventory File Information Logic & Monarch Settings Remode Control Usage Infrastructure Power Control Maintenance Sign out Fan Profile Import Download Messages Target PCB ResourceAccess + new fan profile Status: defaults Status: Status: SPCpower Status: Main

2-6-18 Power Consumption

Items in Power Consumption displays current power consumption reading. You are allowed to configure power limit in the Setting field.

MegaRVC SP-X E:\COLOR\ALL\ST\SPX\KONIX\VLT\103\SPX\KONIX\SPX\ Current Options QualifyTechs... Dashboard Service System Inventory CPU Inventory DBMI Inventory FCH Inventory FCD Inventory HIC Inventory LPG Inventory FPU Information Logic & Response Settings Remote Control Image/Internet/Case Power Control Maintenance Sign out Power Consumption There is no policy covering currently. Power Consumption Reading (include CPU and IO) Current Power Consumption (N) 2 Minimal Power Consumption (N) 2 Maximal Power Consumption (N) 6 Average Power Consumption (N) 8 Platform Power Consumption Limit Setting Name: Power Consumption

MegaRAC SP-X List us Aug to March 2015 Help Scheme Add Limits Platform Power Limit Settings Existing Power Limit Policy Add Power Limit Policy

Procedure

1. Check Setting to configure Platform Power Limit Settings.
2. Click Existing Power Limit Policy to configure Power Limit Policy.
3. Check Add Power Limit Policy to Add Power Limit Policy.

2-6-19 IMPI Interfaces

You are allowed to configure the IPMI interfaces in this page.

MEGARAC SP-X CUELS API (RUSTINEROS EX) - Next Online Quick Belize... Dashboard Server Syncbase Inventory File Information Logo & Resources Settings Networks Central Straight Media Channel Power Control Web Resources Tags Out iPMI Interfaces IPRI Data LMI IPRI Data CXCR Google USE - English Hotbox Networks Home - Settings - USB Interface

Procedure

1. Check IPMI Over LAN to enable IPMI over LAN.
2. Check IPMI Over KCS to enable IPMI over KCS.
3. Click Save to save the configuration.

2-6-20 RAID Management

The RAID Management page allows you to view the Storage Summary, RAID Controller information, Physical Device Information, Logical Device Information and Event Log.

SNL Server Information 01.04.20 Date: 2002/05/03/05/07 © Your Daily Settings Configur SNCL Options Camera NAVES Data & Time Internal User Resources AVN Mouse Setting Log Settings Hardware Infrastructure Settings Network Settings Main Order Settings Platform Switch Filter R&D Management Services SMTP Settings SSL Settings System Firewall User Management Video Recording Fan Profile Power Consumption

RAID Controller Information

To open the RAID Controller Information, click Settings > RAID Management > RAID Controller Information from the menu bar. A sample screenshot of RAID Controller Information section is shown below.

RAID Management R&D Controller Information Storage Summary Physical Device Information Logical Device Information RSD Information Event Log

Note: You can get RAID Controller Information only when Host is in Power ON state.

Serial Number : Displays the Serial number of the RAID Controller.

Package Version : Displays the Package Version number of the RAID Controller.

BIOS Version : Displays the BIOS Version number of the RAID Controller.

UEFI Version : Displays the UEFI version number of the RAID Controller.

Expander Version : Displays the Expander Version number of the RAID Controller.

SEEPROM Version : Displays the SEEPROM Version number of the RAID Controller.

CPLD Version : Displays the CPLD Version number of the RAID Controller.

PCI Vendor Version : Displays the PCI Vendor Id of the RAID Controller.

PCI Device Version : Displays the PCI Device Id of the RAID Controller.

PCI SubVendor ID : Displays the PCI Subvendor Id of the RAID Controller.

PCI SubSystem ID : Displays the PCI Sub-Device Id of the RAID Controller.

ROC Temp (°C) : Displays ROC temperature.

Expander Temp (°C) : Displays the Expander temperature.

RAID Event Log : Displays a graphical representation of all events incurred by the RAID Controller and %occupied/available space in logs. If you click on the Details link, you can view a list of available events.

Storage Summary

This tab displays a brief summary of storage devices available under the RAID controller. To open the Storage Summary section, click Settings > RAID Management > Storage Summary from the menu bar. A sample screenshot of Storage Summary section is shown below.

MEGARAC SP-X Fileware Information 12.01.201225 May 13 2019 19:20:46 CST Host Office Quick Links... Dashboard Sensor FRU Information Logs & Reports Settings Remote Control Image Redirection Power Control Maintenance Storage Summary RAID Controller AvAGO MegaRAID SAI 9380-Be (261 ) Physical Devices Count: 0 Logical Devices Count: 0 Hot Spares Count: 0 Sync Refresh admin Home - Settings - RAID Management - Storage Summary

Physical Devices Count : Displays the number of Physical Devices connected to the controller. Logical Devices Count : Displays the number of Logical Devices configured and available under the controller.

Physical Device Information

This tab displays the details about the Physical Devices connected to the RAID controller. To open the Physical Device Information, click Settings > RAID Management > Physical Device Information from the menu bar. A sample screenshot of Physical Device Information section is shown below:

MEGARAC SP-X Filemore Information 12.01.201225 Apr 24 2013 18:46:56 CST © Host Office Quick Links... Dashboard Sensor FRU Information Logs & Reports Settings Remote Control Image Redirection Power Control Maintenance Physical Device Information Select the RAID Controller AVAGO MegaRAID SAS 9460-BI (260) Clear Foreign Configuration Device ID Controller Media Type State Slot Speed Link Speed Size Temp Foreign Dedicated HotSpars Information (Logical Device Name) 1 AVAGO MegaRAID SAS 9460-BI (260) HDD Online 4 3.0Gb/s 3.0Gb/s 298 44 - - 3 AVAGO MegaRAID SAS 9460-BI (260) HDD Dedicated HOT_SPARE 5 6.0Gb/s 6.0Gb/s 931 39 - aaaa 4 AVAGO MegaRAID SAS 9460-BI (260) HDD UNCONFIGURED_GOOD 7 6.0Gb/s 6.0Gb/s 465 40 - - 9 AVAGO MegaRAID SAS 9460-BI (260) HDD Online 3 6.0Gb/s 6.0Gb/s 465 37 - - 10 AVAGO MegaRAID SAS 9460-BI (260) HDD Online 0 3.0Gb/s 3.0Gb/s 298 36 - - 135 AVAGO MegaRAID SAS 9460-BI (260) HDD UNCONFIGURED_GOOD 255 Not Defined Not Defined 0 0 - -

Select the RAID Controller : To view the details of specific RAID Controller.

Device Id : Displays the Device ID of physical device available under selected RAID controller.

Controller : Displays the name of RAID controller to which the physical device is attached.

Media Type : Displays the media type of physical device that is attached to the selected RAID controller.

State : Displays State of the Physical Device (either online, or offline).

Slot : Displays Slot number, through which Physical Device is connected to the back plane.

Speed : Displays the speed of the Physical Device in Gb/s.

Link Speed : Displays the link speed of the Physical Device in Gb/s.

Size (GB) : Displays the Size of the Physical Device.

Temp (°C) : Displays the Temperature of the Physical Device.

To perform additional operations, click on the slot or expand the (+) icon. A sample screenshot is shown below.

MEGNAC SP-X www.information 12.08.2016 For 21 SEP23/04/05/21

our offer

Device ID: Continuous Video Type: Stable Speed Speed Slow Speed Stop (GB) Temp (K) Foreg Deceased the Rapid Controller: AVOCO MegaTA B 340-5400-3 (200) - Over-Range Configurations 1 AVOCO MegaTA B 340-5400-3 (200) 2 AVOCO MegaTA B 340-5400-3 (200) 3 AVOCO MegaTA B 340-5400-3 (200) 4 AVOCO MegaTA B 340-5400-3 (200) 5 AVOCO MegaTA B 340-5400-3 (200) 6 AVOCO MegaTA B 340-5400-3 (200) 7 AVOCO MegaTA B 340-5400-3 (200) 8 AVOCO MegaTA B 340-5400-3 (200) 9 AVOCO MegaTA B 340-5400-3 (200) 10 AVOCO MegaTA B 340-5400-3 (200) 11 AVOCO MegaTA B 340-5400-3 (200)

View Physical Device Information: Click View Icon to view more details about the Physical Device Information, including Device Id, Vendor Id, Product Id, Serial Number, Power State, and Interface Type. A sample screenshot of View Physical Device Information page is shown below.

MEGARAC SP-X Enerware Information 2.03.8.2014 Dec 9 2016 0027161 RT @ host offline Quick Links... Dashboard Sensor FRU Information Lungs & Reports Settings Remote Control Image Redirection Power Control Maintenance Sign out Physical Device Information Device ID 25 Vendor ID ATA Product ID INTEL SGD/SC2R812 Serial Number BTWL332R09OF120LGN Power State Spun Up Interface Type SATA

Logical Device Information

This tab displays the details about the Logical Devices configured under the RAID controller. To open the Logical Device Information section, click Settings > RAID Management > Logical Device Information from the menu bar. A sample screenshot of Logical Device Information section is shown below:

2023-03-08 06:05:34 (CYC+85.00 GMT) Logical Device Information Select the RMS Card suite - Digitality HR-2028-CSA/CSA (257) LD Name Contodors Type State Broad Policy Write Policy Cache Policy Access Policy New Play Devens True Digitality HR-21.00-CRA/CSA (257) RMOD Optimal No Read/Thread Write TR-Kough Direct ID Read Write 2 Create Virtual Devices Start Patrol Real Operation BMC Software Information 12.00.39 Rev 0 2022 10:40:25:45:55 Not Online Source Views... Exchange Settings - RMS Management - useful Disinformation Name : Settings - RMS Management - useful Disinformation

Select the RAID Controller : To view the details of the Logical devices configured under the specific RAID controller.

LD Name : Displays the name of the Logical Device configured under selected RAID controller.

Controller : Displays the Name of the RAID Controller under which the Logical Devices are configured.

Type : Displays the type of RAID level in which the Logical Device is configured, e.g. RAID O or RAID 1 etc.

State : Displays the state of the Logical Device (either online or offline).

Read Policy : Displays the Read Policy details of the Logical Device.

Write Policy : Displays the Write Policy of the Logical Device.

Cache Policy : Displays the Cache Policy details of the Logical Device.

No. of Physical Devices : Displays the number of Physical Devices available under the specific Logical device.

To perform additional operations, click on the slot or expand the (+) icon available for each Logical Device. A sample screenshot is shown below.

LOGICAL DEVICE INFORMATION Select the RAI5 Controller: Logical Site:0336-CPNCA48 (2017) L3 Name 2 Contorion 2 Type 2 State 2 Read Policy 2 Write Policy 2 Cache Policy 2 Access Policy 2 Next Play Services 2 View: Digital in HR-LLDH CRANSLAR (2017) MPX30 Digital Auto Read Interface Write Through Direct To Go Read Account 1 Create Virtual Devices Next Panel Real Operations

View Physical Device info for selected Virtual Device : Clicking on the icon will display the Logical Physical Device Information page, It lists the information of physical devices configured for specified logical device. A sample screenshot of View page is shown below:

2023-02-08 06:00:59 (UTC+00:00 GMT) Logical Device Information Select the RAI's Controller: Log-Rate Wi-Fi 0139-0794148 (2017) LS Home # Controller # Type # Status # Royal Policy # Write Policy # Cache Policy # Access Policy # New/Fly Settings # Test: -Digital Wi-Fi 0139-0794148 (2017) MS/OS 2p/OS/SD 36.8kV/MS/OS 26.6kV Through S/MS/OS 36.8kV/OS 1 Create Virtual Device Start/Start Real Operations OK Consumer Information 13.04.29 No P/NCE 0344366-02 Post Options Options Backup Environment Systems Inventory FDS information Logic & Projects Settings Visual Control Image Realization Power Control Maintenance Sign out

Digital Commerce Information COMPLER Data & 2022 SIGMA-0348 Visual Basic Logical Physical Device Information Selected SIGMA-Controller/Stragency M1.000-CMS4348 (257) Level Devices (B) of Logical Devices (C) Device ID # Controller Name # Type # State # Slot # Speed # Link Speed # Size (GB) # Temp (K) # OK Sigalytev-VIR-2000-CMS4348 (257) H3D Online 1 6.9Gb/s 6.8Gb/s 558 55

Check Advanced Properties : Click icon to view the advanced properties of the selected Logical device. A sample screenshot is shown below.

Logical Device Information Select the KIID Controller: logStyle: 401336-264048 (201) LSI Name # Catalyst # Type # Style # Bond Policy # Write Policy # Cache Policy # Access Policy # RealPlay Devices # Text LogStyle: 401336-264048 (201) NAD# Optimal Info Through Break List Create Virtual Device 2013/09/00 RealPlay Operations

BMC Command Information LUXLER On 3.2022 SQL/SLR EXT - Host Banking Logical Device Information Done Stay all Rk File Installed SDD-Cacking Download Progress Unknown Initualization Rate In Initualization Initual Customer Progress Percentage 45% Bad History Table Empty Stay (SBY) root

Delete Virtual Drive : Click icon to delete selected virtual device. A pop-up message prompts you to confirm your choice. Upon confirmation, you will be informed about the status.

Logic Device Information Default for R&D Connection: Logically Win 2018 (CINN246 [2017]) LSI Name: Contentlog Type: Style: Real Policy: Write Policy: Cache Policy: Access Policy: New/Full Services: LOG: Digital for HR-1039-CAMR54 [2017] PAGE: Digital: Real Policy Write Through: March 10 Real Device: 1 Create Virtual Devices Start Virtual Base Experience

To Create Virtual Device:

1. Click Create Virtual Device to create Logical Volume of the Device. A sample screenshot of Create Virtual Device page is shown below.

Create Virtual Device Skill Level ASCE Logical Privacy Rules Installation Non-Configuration Bridge Size Level Need Policy To Find Mixed Write Policy Apply Through at Policy Draw It Resume Policy Power Links Seed Case Policy C:\Target Form\Figure\Physical\Final URL: 400-866 Data Lfd. Global B2.123 F1.256 Network Software Name - Design - Web Management - Logical Data Information - Create Virtual Device

1. Select Controller Name from the drop-down lists.
2. Select RAID Level from the drop-down lists. A sample screenshot of RAID Levels is as shown below:

Note: Only RAID Levels RAID00, RAID10, RAID50 and RAID60 will support Span Creation.

Create Virtual Device WIN Controller Name: Signify the User Interface (User) Build Local Auto Model AutoBook Information no information Print Size Size Print Policy No Print Wizard Write Policy Allow Through All Policy Direct IT Adjust Policy Read Time Show Data Policy UnChanged ########## and click any code 326 - 4021-098

1. Enter the depth of the Span in Span Depth field.
2. Enter the number of Drives in Drives per Span field.

Note: UnConfigured Physical Drives should be equal to multiples of Span Depth and Drives per Span.

1. Select UnConfig Physical Drives from the drop-down lists.

2. Click Create Span for mapping Span Id's to the selected Physical Drives. The mapped Span Id for the selected Unconfigured Physical Drives will be displayed as shown in the above screenshot.

3. Enter Logical Name of the Device.

4. Select Initialization type from the drop-down lists.

5. Select Stripe Size (KB), Read Policy, Write Policy, IO Policy, Access Policy, Disk Cache Policy and UnConfigured Physical Drives details from the respective drop-down lists.

6. Click Save to add the information to the Logical Device Information. The information will be added and displayed in the Logical Device Information page.

To Delete Logical Device

Select the Device to be deleted and click Delete Logical Device to delete the selected logical volume. The selected virtual device will be deleted.

Event Log

This page displays all the RAID Controller events occurred that has been already configured. To open the Event Log section, click Settings > RAID Management > Event Log from the menu bar.

Note: All the events mentioned here are read-only and cannot be edited.

A sample screenshot of Event Log section is shown below:

Event Log Select the RMB Controller: Gigabyte MR-3108-CMA4548 (257) Select the Event Type All Events Clear Event Log Controller 3 Gigabyte MR-3108-CMA4548 (257) Gigabyte MR-3108-CMA4548 (257) Gigabyte MR-3108-CMA4548 (257) Gigabyte MR-3108-CMA4548 (257) Gigabyte MR-3108-CMA4548 (257) Gigabyte MR-3108-CMA4548 (257) 190 02/06/2023 370 LP Events Info Events Gigabyte MR-3108-CMA4548 (257) Gigabyte MR-3108-CMA4548 (257) Gigabyte MR-3108-CMA4548 (257) Gigabyte MR-3108-CMA4548 (257) Gigabyte MR-3108-CMA4548 (25T) Gigabyte MR-3108-CMA4548 (25T) Gigabyte MR-3108-CMA4548 (25T) Gigabyte MR-3108-CMA4548 (25T) Gigabyte MR-3108-CMA4548 (25T) Gigabyte MR-3108-CMA4548 (257) Gigabyte MR-3108-CMA4548 (257) Gigabyte MR-3108-CMA4548 (257) Gigabyte MR-3108-CMA4548 (257) Gigabyte MR-3108-CMA4548 (25T) 190 02/06/2023 370 LP Events Info Events Gigabyte MR-3108-CMA4548 (257) Gigabyte MR-3108-CMA4548 (257) Gigabyte MR-3108-CMA4548 (257) Gigabyte MR-3108-CMA454A (257) Gigabyte MR-3108-CMA4548 (257) Gigabyte MR-3108-CMA4548 (257) Gigabyte MR-3108-CMA4548 (257) Gigabyte MR-3108-CMA4548 (257) Gigabyte MR-3108-CMA454B (257) Gigabyte MR-3108-CMA454B (257) Gigabyte MR-3108-CMA454B (257) Gigabyte MR-3108-CMA454B (257) Gigabyte MR-3108-CMA454B (257) Gigabyte MR-3108-CMA454A (257) Gigabyte MR-3108-CMA454A (257) Gigabyte MR-3108-CMA454A (257) Gigabyte MR-3108-CMA454A (257) Gigabyte MR-3108-CMA454A (257) Gigabyte MR-3108-CMA454B (257) Gigabyte MR-3108-CMA454B (257) Gigabyte MR-3108-CMA454B (257) Gigabyte MR-3108-CMA454B (257) Gigabyte MR-3108-CMA454C (257) Gigabyte MR-3108-CMA454C (257) Gigabyte MR-3108-CMA454C (257) Gigabyte MR-3108-CMA454C (257) Gigabyte MR-3108-CMA454C (257) Gigabyte MR-3108-CMA454D (257) Gigabyte MR-3108-CMA454D (257) Gigabyte MR-3108-CMA454D (257) Gigabyte MR-3108-CMA454D (257) Gigabyte MR-3108-CMA454D (257) Gigabyte MR-3108-CMA454E (257) Gigabyte MR-3108-CMA454E (257) Gigabyte MR-3108-CMA454E (257) Gigabyte MR-3108-CMA454E (257) Gigabyte MR-3108-CMA454E (257) Gigabyte MR-3108-CMA454F (257) Gigabyte MR-3108-CMA454F (257) Gigabyte MR-3108-CMA454F (257) Gigabyte MR-3108-CMA454F (257) Gigabyte MR-3108-CMA454F (257) Gigabyte MR-3108-CMA454E (257) Gigabyte MR-3108-CMA454E (257) Gigabyte MR-3108-CMA454E (257) Gigabyte MR-3108-CMA454E (257) Gigabyte MR-3108-CMA454A (26) Gigabyte MR-3108-CMA454A (26) Gigabyte MR-3108-CMA454A (26) Gigabyte MR-3108-CMA454A (26) Gigabyte MR-3108-CMA454A (26) Gigabyte MR-3108-CMA454A (26) Gigabyte NR-Gi(Gi(Gi(Gi(Gi(Gi(Gi(Gi(Gi(Gi(Gi(Gi(Gi(Gi(Gi(Gi(Gi(Gi(Gi(Gi(Gi(Gi(Gi(Gi(Gi(Gi(Gi(Gi(Gi(Gi(Gi(Gi(Gi(Gi(Gi(Gi(Gi(Gi(Gi(Gi(Gi(Gi(Gi(Gi(Gi(Gi(Gi(Gi(Gi(Gi(Gi Gti(Gi(Gi(Gi(Gi(Gi(Gi(Gi(Gi(Gi(Gi(Gi(Gi(Gi(Gi(Gi(Gi(Gi(Gi(Gi(Gi(Gi(Gi(Gi(Gi(Gi(Gi(Gi(Gi(Gi(Gi(Gi(Gi(Gi(Gi(Gi(Gi(Gi(Gi(Gi(Gi(Gi(Gi(Gi(Gi(Gi(Gi(Gi(Gi(Gi(Gci(Gi)(Gi)(Gi)(Gi)(Gi)(Gi)(Gi)(Gi)(Gi)(Gi)(Gi)(Gi)(Gi)(Gi)(Gi)(Gi)(Gi)(Gi)(Gi)(Gi)(Gi)(Gi)(Gi)(Gi)(Gi)(Gi)(Gi)(Gi)(Gi)(Gi)(Gi)(Gi)(Gi)(Gi)(Gi)(Gi)(Gi)(Gi)(Gi)(Gi)(Gi)(Gi)(Gi)(Gi)(Gi)(Gi)(Gi)(Gi)(Gi)(Gi)(Gi)(Gr)(Gi)(Gi)(Gi)(Gi)(Gi)(Gi)(Gi)(Gi)(Gi)(Gi)(Gi)(Gi)(Gi)(Gi)(Gi)(Gi)(Gi)(Gi)(Gi)(Gi)(Gi)(Gi)(Gi)(Gi)(Gi)(Gi)(Gi)(Gi)(Gi)(Gi)(Gi)(Gi)(Gi)(Gi)(Gi)(Gi)(Gi)(Gi)(Gi)(Gi)(Gi)(Gi)(Gi)(Gi)(Gi)(Gi)(Gr)(Gr)(Gr)(Gr)(Gr)(Gr)(Gr)(Gr)(Gr)(Gr)(Gr)(Gr)(Gr)(Gr)(Gr)(Gr)(Gr)(Gr)(Gr)(Gr)(Gr)(Gr)(Gr)(Gr)(Gr)(Gr)(Gr)(Gr)(Gr)(Gr)(Gr)(Gr)(Gr)(Gr)(Gr)(Gr)(Gr)(Gr)

The Event Log page consists of the following Fields.

Select the Event Type: This field is to filter the type of event to be viewed among all available events under specified RAID controller. The category could be either All Events, LD events, PD Events, Enclosure Events, BBU Events, SAS Events, Controller Events, Configuration Events and Cluster Events.

Note: Filtering can be done with the Events mentioned in the list. Once the Event Log category is chosen in the Event type drop-down list then the filtered events will be displayed with the Record ID, Time Stamp, Event Code, Event Type and Event Class.

Navigational arrows can be used to selectively access different pages of the Event Log.

Clear Event Log: To delete all the event logs.

Procedure

1. Select the RAID Controller from the drop-down list.
2. Select the Event Type from the drop-down list.
3. To clear all events from the list, click Clear Event Log.

2-7 Remote Control

The system and browser requirements for Remote Control are given below.

System Requirements

• Client machine with 8GB RAM.
• If the client machine has 4GB RAM, there will be lag in Video/keyboard/mouse functionality.

Supported Browsers

• Chrome latest version.
• IE 11 and above.
• Firefox (with limited support).

Note: It is advisable to use Chrome or IE for H5Viewer, since Firefox has its own memory limitations.

To open the Remote Control page, click Remote Control from the menu bar. A sample screenshot of the Remote Control page is shown below.

NEGAIRAC SP-X E3L3.3F NYS RECORDED SFX View Before Quick URL... Default/Forward Server System repository PBU Information Logic & Resources Settings Networks Control Hedge Resource Power Control Maintenance Sign out Remote Control: Remove USB & DSL. HSV viewer USB will go to remote service settings. Current/Attacker JV viewer Switch/Power Serial Over LAN Access Identify LED Status City Action Turn-DBY Turn-DFY Lighting Time (Seconds) Unlimited Save

The fields in the Remote Control page are explained below.

H5Viewer: Launches the KVM.

JViewer: Downloads the jviewer file.

Serial Over LAN: Launches the HTML5 Serial Over LAN window.

Identify LED: Turns on/off the chassis identification LED.

H5Viewer

On the Remote Control page, click Launch H5Viewer. A sample screenshot of the H5Viewer page is shown below.

Stop KIM Video • Mouse • Options • Keyboard • Send Keys • Hot Keys • Video Record • Power • Active Users • Help • Recycle Bin reborder CL2100_CL... outputing... Puning Driver CD image: Browse File (0 KB) Save 396%

Stop KVM: Stops the H5Viewer.

Video: Consists of the following items:

• Pause Video: Pauses Console Redirection.
• Resume Video: Resumes the Console Redirection when the session is paused.
• Refresh Video: Updates the display shown in the Console Redirection window.

Mouse: Contains the following items:

• Show Client Cursor: Shows or hides the local mouse cursor on the remote client system.
- Mouse Mode: Handles mouse emulation from local window to remote screen using either of the two methods. Only 'Administrator' has the right to configure this option.
- Absolute mouse mode: The absolute position of the local mouse is sent to the server if this option is selected.
- Other mouse mode: Sets the client cursor in the middle of the client system and will send the deviation to the host. This mouse mode is specific for SUSE Linux installation.

Note: Client cursor will be hidden always. If you want to enable, use Alt + C to access menu.

Options

Zoom In / Zoom Out: Allows you to adjust zoom level.

Partial Permission / No Permission: Enables/Disables the access privilege of the user.

Auto Detect / 256 Kbps / 512 Kbps / 1 Mbps / 10 Mbps / 100 Mbps: Adjusts the bandwidth.

YUV 420 / YUV 444 / YUV 444 + 2 color VQ / YUV 444 + 4 color VQ: Adjusts the color encoding mode.

0 Best Quality - 7: Allows you to adjust the screen resolution.

Keyboard: lists the host physical keyboard languages supported in H5Viewer.

• English U.S
• German
• Japanese

Send Keys: Enters items.

This menu contains the following sub menu items:

• Hold Down
• Press and Release

Hold Down: Contains the following items:

• Right Ctrl Key: Acts as the right-side key when in Console Redirection.
  • Right Alt Key: Acts as the right-side key when in Console Redirection.
• Right Windows Key: Acts as the right-side key when in Console Redirection.
• Left Ctrl Key: Acts as the left-side key when in Console Redirection.
  • Left Alt Key: Acts as the left-side key when in Console Redirection.
• Left Windows Key: Acts as the left-side key when in Console Redirection. You can also decide how the key should be pressed: Hold Down or Press and Release.

Press and Release

• Ctrl+Alt+Del: Acts as if you depressed the , and keys down simultaneously on the server that you are redirecting.
• Left Windows Key: Acts as the left-side key when in Console Redirection. You can also decide how the key should be pressed: Hold Down or Press and Release.
• Right Windows Key: Acts as the right-side key when in Console Redirection.
• Context Menu Key: Acts as the context menu key, when in Console Redirection.
• Print Screen Key: Acts as the print screen key, when in Console Redirection.

Hot Keys: Adds the user configurable shortcut keys to invoke in the host machine.

The configured key events are saved in the BMC.

- Add Hot Keys: Enables User Defined Macros. Click Add to add a User Defined Macro.

Video Record: Contains the following items:

• Record Video: Starts recording the screen.
- Stop Recording: Stops the recording.
- Record Settings: Sets Video Recording Duration.

Note: The Maximum video file size allowed is around 40MB. If the video file size reaches its max size limit, the recorded file is downloaded and recording will be in progress until the configured video recording time is reached. The video file is saved as video_date-month-year_hr-min-sec_partno in client side video recording.

Users have to take care of saving the video files in different browsers.

When H5viewer focus is lost and if video recording is in progress, the recording will be stopped with a notification message and the recorded video file will be discarded. Due to browser limitation, Set timeout/set interval will be delayed from specified time of interval when browser window loses focus, Hence, video server will not send the video packets to H5viewer and so the video recording will be stopped.

Note: Windows 2016 installation takes 1 hour and 52 minutes to install on Ironman through the BMC ISO redirection.

Power: Performs any power cycle operation.

• Reset Server: Reboots the system without powering off (warm boot).
• Immediate Shutdown: Turns off the server immediately.
• Orderly Shutdown: Turns off the server in proper order.
  • Power ON Server: Powers on the server.
• Power Cycle Server: Performs server power control operation.

Active Users: Displays the active users and their system IP address. Active KVM Session can be terminated when there are multiple KVM Session from Master [FULL Privilege KVM Session].

Help: Displays information about H5Viewer.

Browse File: Selects the CD image file to be redirected to the host.

Start Media: Redirects the selected CD image file to the host.

Stop Media: Stops the CD media redirected to the host.

Zoom 100%: Displays the zoom level.

Host Display

• Display on: If you disable this option, the display will be shown on the screen in Console Redirection
• Display off: If you enable this option, the server display will be blank but you can view the screen in Console Redirection. If you disable this option, the display will be back in the server screen.
• Capture Screen: Takes the screenshot of the host screen and save it in the client's system.

Power ON/OFF: Power ON/OFF the server.

Procedure

1. Click Launch H5Viewer to start video redirection.

Stop Help File Edit View Insert Tools Help RecycleBox Adobe LUTR-CL My Documents My Documents CD Images, Browser files (3.1 KB) View Help Close Web

1. Click Browse File to select CD Image.
2. Click Start Media to redirect the selected CD image file to the Host. A sample screenshot is as shown below.

CD Images: video-server 7.0 files_p44.p64.c2 [70% KB] File Home Share View Message This PC + CD drive (E:\RHEL\7.0 Server Search CD drive (S) Desktop Downloads Documents Pictures The PC Desktops Documents Downloads Music Pictures Videos Local Disk (C:) CD Drive (E:\RHEL\7.0 Server Name Date-modified Type Size aditors 5/7/2014 2/18.0M File folder Image 5/7/2014 2/18.0M File folder images 5/7/2014 2/18.0M File folder sales 5/7/2014 2/18.0M File folder blueOffs 5/7/2014 2/18.0M File folder packages 5/7/2014 2/18.0M File folder release notes 5/7/2014 2/18.0M File folder repudite 5/7/2014 2/18.0M File folder discinfo 5/7/2014 2/13.0M DISINFOYA 1 KB TreemapYrsA 5 KB TUEA 4/6/2014 302.AIM File 9 KB GPS 3/6/2012 60K.AIM File 10 KB mediapages 5/7/2014 310.0M WOM Files 1 KB SPM-SPG-KEY release beta 4/3/2014 623.AIM File 4 KB SPM-SPG-KEY release release 4/3/2014 623.AIM File 4 KB Tikul.Til. 5/7/2014 310.0M Til.1a. 2 KB

1. To stop the CD Image redirection, click Stop Media.

JViewer

JViewer allows you to download the jviewer file. Click Launch JViewer to download the jviewer file.

Note: The jviewer file is used for launching Java executable files over the web or network.

Serial Over LAN

Serial Over LAN can launch the HTML5 Serial Over LAN window. Click Activate to launch the HTML5 Serial Over LAN window. A sample screenshot of the HTML5 Serial Over LAN window is shown below.

MEGARAC SP-X - Google Chrome ▲ 不安全 | 60.250.82.79/#serial_over_lan Deactivate Columns 80 Rows 25

2-8 Images Redirection

This page is used to configure the images into BMC for redirection. This can be done either by uploading an image into BMC or by mounting the image from the remote system.

To open the Image Redirection page, click Image Redirection from the menu bar. A sample screenshot of the Image Redirection page is shown below.

MEGAINE SPACE ELEC.03 MAGNETS MIGARES In Excel Table Data Source: BackMap Internet Systems Repository Intel Information Image & Image Settings Mouse Clicks of Image Refreshments Power Settings Add和完善 Log mix Image Redirection Remove images Name: ImageRedirection

The fields in the Image Redirection page are explained below.

Remote Images: Allows you to configure images of remote media servers.

Note: VMedia Privilege only restricts initiating / starting media redirection. If a device is ready being redirected and attached to the host, then in host it will be visible as normal time. Hence it will be accessible to all the KVM sessions. Which includes 'KVM privilege only' sessions as well.

2-8-1 Remote Media

The Remote Media tab displays the configured images of remote media server on BMC.

MEGARAC SP-X 13:08:30 Aug 5 2016 47:15:34 UTC @ Next Office Quick Lock... Defaultboard Server Systems Inventory FXU Information Log 6 Requests Settings Runtime Control Image Redirect to Power Control Maintenance Sign out. Remote Media: Ensure CD/DVD+3D Images in the network to host as media through BRC Click here to go to Media General Settings or . Media Type Media Instance Image Name Redirection Status Connected Server Session Index CD/DVD 0 RZT2P36.1x# - 0 ▶ □ △ CD/DVD 1 RZT2P36.1x# - NA ▶ □ △ CD/DVD 2 RZT2P36.1x# - NA ▶ □ △ CD/DVD 3 RZT2P36.1x# - NA ▶ □ △ Hard disk 0 - NA ▶ □ △ Hard disk 1 - NA ▶ □ △ Hard disk 2 - NA ▶ □ △ Hard disk 3 - NA ▶ □ △

Note: More than one image can be configured for each image type. At maximum 4 ages can be configurable.

To configure the image, you need to enable Remote Media support under

Settings > Media Redirection > General Settings.

To start/stop redirection and to delete an image, you must have Administrator Privileges. Free slots are denoted by "\~"

The fields in the Remote Media page are explained below:

Media Type: Displays type of Media such as CD/DVD and Harddisk.

Media Instance: Displays total media instance count.

Image Name: Displays the default recovery image name on the server.

Redirection Status: Displays the status of the media.

Connected Server Session Index: Displays Media Server Session Index.

Start/Stop Redirection: Starts/stops the image redirection.

Pause: Pauses the image redirection.

Refresh Image List: Gets the latest image list from the remote storage.

Sync Image Status: Synchronizes the image status.

Procedure

1. To Start/Stop Redirection and configure remote media images, click (Start/Stop icon) and make sure Remote Media Support option is enabled.

Note: The Start Redirection button is active only for VMedia enabled users.

1. Select a configured slot and click (Start/Stop icon) to start the remote media redirection. It is a toggle button, if the image is successfully redirected, then click (Start/Stop icon) to stop the remote media redirection.

Note: Redirection needs to be stopped to clear the image.

2-9 Power Control

The Power Control page allows you to view and control the power of your server.

To open the Power Control page, click Power Control from the menu bar. A sample screenshot of Power Control is shown below.

MEGARAC SP-X 12.01.20 MPS 2023 PROCES SPC Hot Online Quick Online... Dashboard Server Digital Inventory File Information Logic & Resources Settings Remode Control Intelligent Hardware Power Control Maintenance Sign out Power Control in Main Server Power Actions Find it currently on Power Off Power Die Power Cycle Hard Reset ACR Shutdown Patterns Action Name: Power Control

The setting options of Power Control are explained below.

Power Off: Powers off the server immediately.

Power On: Powers on the server.

Power Cycle: This option will first power off, and then reboot the system (cold boot).

Hard Reset: This option will reboot the system without powering off (warm boot).

ACPI Shutdown: Initiates operating system shutdown prior to the shutdown.

Perform Action: Performs the selected operation.

Procedure

Select an action and click Perform Action to proceed with the selected action.

Note: During Execution you will be asked to confirm your choice. Upon confirmation, you be informed about the status after few minutes.

Note: It is advisable to use Chrome or IE for H5Viewer, since Firefox has its own memory limitations.

2-10 Maintenance Group

The Maintenance Group page allows you to do maintenance tasks on the device. To open the Maintenance Group page, click Maintenance Group from the menu bar.

Maintenance Group contains the following items:

• Backup Configuration
• Firmware Image Location
• Firmware Information
• Firmware Update
• Preserve Configuration
• Restore Configuration
• Restore Factory Defaults
• System Administrator

A sample screenshot of Maintenance Group is shown below.

MEGARAC SP-X C:\10.3\2019\MEGARAC SP-X File Online Quick Links... Defaultboard Sensor Syncbase inventory File Information Logic & Impacts Settings Remande Central Usage Monitoring Power Control Maintenance Sign out Maintenance Backup Configuration Hardware Installation Location Hardware Information Pressure Update Pressure Configuration Restore Configuration Restore Factory Defaults System Administrator

2-10-1 Backup Configuration

This page allows you to select the specific configuration items to be backed up in case of "Backup Configuration".

To open the Backup Configuration page, click Maintenance > Backup Configuration from the menu bar. A sample screenshot of Backup Configuration page is shown below.

MEGARAC SP-X MAGUIR AI'S BUSINESS-INFO Host Editing Quick Loans... Dashboard Server Systems inventory File information Logic & Impacts Settings Remode Control Intage/Network/Cloud Power Control Maintenance Sign out Backup Configuration Check All Sleep XMI Network & Network Video ATP Authentication SPS/SH Exercise

The fields in the Backup Configuration page are explained below.

Check All: Selects all setting options.

Download: Downloads and saves the configuration files backup from BMC to client system.

Procedure

1. Click Check All to back up all setting option or check individual setting option to back up the selected items.
2. Click Download to save the backup file to the client system.

2-10-2 Firmware Image Location

This page is used to configure firmware image into the BMC.

To open the Firmware Image Location page, click Maintenance > Firmware Image Location from the menu bar. A sample screenshot of Firmware Image Location page is shown below.

MEGARAC SP-X 12.0.18 M/F5 (NEE13) 1996-0000-0001 Quick Online... Dashboard Server Synbase inventory File information Tags & Requests Settings Bremode Control Image/Redistribution Power Control Maintenance Sign out Firmware Image Location Image Location Type With typing during Read FTP Server STTP Server Address Requested, if FTP is available STTP Image Name Requested, if FTP is available FTP Ready Command E Save

The fields in the Firmware Image Location page are explained below.

Image Location Type: Type of location to transfer the firmware image into the BMC either Web Upload during Flash or TFTP Server.

TFTP Server Address: Address of the server where the firmware image is stored.

Note: The Server supports both IPv4 and IPv6 addresses

TP Address made of 4 numbers separated by dots as in "xxx.xxx.xxx.xxx".

Each number ranges from 0 to 255.

First number must not be 0.

IPv6 Address made of 8 groups of 4 Hexadecimal digits separated by colon as in "xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx."

Hexadecimal digits are expressed as lower-case letters.

TFTP Image Name: Full Source path with filename of the firmware image is stored on TFTP Server.

TFTP Retry Count: Number of times to be retried in case a transfer failure occurs. Retry count ranges from 0 to 255.

Save: Saves the configured settings.

Procedure

1. Select the Image Location Type (Web Upload during flash / TFTP Server).
2. If the protocol selected is TFTP, enter the IP address of the server in the TFTP Server Address field.
3. Enter the TFTP Image Name in the given field
4. Enter the TFTP Retry Count value.
5. Click Save to save the changes.

2-10-3 Firmware Information

To open the Firmware Information page, click Maintenance > Firmware Information from the menu bar. A sample screenshot of the Firmware Information page is shown below.

MEGARAC SP-X LEAVLR M&S 2021 MEGARAC SP-X Host Online Quick Links... Outboard Sensor Systems Inventory GUI Information Log & Reports Settings Genade Control Image Coordination Power Control Maintenance Sign out Firmware Information BMC Firmware Information Act/Iter: Notagh ID Build Date 2019-2021 Build Time: 06:30:25 UTC Firmware version: 12.01.2W BIOS Firmware Information Product Manufacturer 04/08/TE Product Maker P132-AK1-OR Build Date P132-06/01 Firmware version: FH CPLD Firmware Information Firmware version: ML 21 Location 1.12

The fields in the Firmware Information page explained below.

BMC Firmware Information

Active Image ID: Displays the active image ID.

Build Date: Displays the build date of the active BMC image.

Build Time: Displays the build time of the active BMC image.

Firmware version: Displays the firmware version of the active BMC image.

BIOS Firmware Information

Product Manufacturer: Displays the hardware manufacturer.

Product Name: Displays the model name of the device.

Build Date: Displays the build date of the device.

Firmware version: Displays the BIOS version installed on the device.

CPLD Firmware Information

Firmware version: Displays the CPLD Firmware version.

2-10-4 Firmware Update

To open the Firmware Update page, click Maintenance > Firmware Update from the menu bar. The update wizard will take you through the update process. A reset of the box will automatically follow if the upgrade is completed or cancelled. An option to Preserve All Configuration is available; enable it, if you wish to preserve already configured settings through the upgrade.

Warning: Please note that after entering the update mode wizard, other web pages and services will not work. All open widgets will be closed automatically. If the upgrade process is cancelled in the middle of the wizard, the device will be reset.

Note: The firmware upgrade process is a crucial operation. Make sure that the chances power or connectivity loss are minimal when performing this operation.

Once you enter into Update Mode and choose to cancel the firmware flash operation, the BMC must be reset. This means that you must close the Internet browser and log back onto the BMC before you can perform any other types of operations.

Once Firmware upgrade using web is started, the regular IPMI command will not be allowed for safety concern if Enable IPMI Command handling during flashing support is disabled in project configuration.

Sample screenshots of Firmware Update are shown below.

BMC Update

MEGARAC SP-X 13.00.00 Sep 2 2020 08.27.25 UTC Default Online Quick Links... Dashboard Sensor System Inventory FRU Information Logs & Reports Settings Remote Control Image Redirection Power Control Maintenance Sign out Firmware Update Damp BIOS Note: Following are the Firmware update methods and components supported in this page. • Dual Firmware update. • BIOS update (*.rbc). — Easy BIOS Refresh • MB_CPLD update (*.rbc) • BPS_CPLD update (*.rbc) • CPLD • BIOS Firmware update Select Firmware Image Choose File : non_v13.01.33.xma_enc Start firmware update Protocol Type: HTTPS Update Type: BMC The dual image formation to be used for firmware update is displayed as follows. To configure Image to be booted from upon reset, choose 'Dual Image Configuration' under Maintenance. Current Active Image Image-1 Image to be Updated Image 1 US - English Sync Refresh admin Home Maintenance Firmware Update

BIOS Update

MEGARAC SP-X 13.09.00 Sep 2, 2021 08/17:56 GMT Quick Links... Dashboard Server System Inventory TRU Information Logs & Reports Settings Remote Control Image Redirection Power Control Maintenance Sign out 2021-09-08 18:00:52 (UTC+00:00 GMT) US - English Sync Refresh admin Firmware Update Dump BIOS Note: Following are the Firmware update methods and components supported in this page. • Dual Firmware update. • BIOS update (*.rbs). — Easy BIOS Refresh • MD_CPLD update (*.rdu). • BPS_CPLD update (*.tsc). • CPLD • BIOS Firmware update Select Firmware Image Choose File Image.RSU Start firmware update Protocol Type: HTTPS Update Type: BIOS select BIOS BIO51 BIO52

The fields in the Firmware Update page are explained below.

Dump BIOS: Click to dump the current BIOS image.

Choose File: Selects the firmware image to be uploaded.

Note:

If you select a BIOS file to be uploaded, you need to select BIOS1 or BIOS2 in the select BIOS field.

If you select a BMC image to be uploaded, you need to select Image 1 or Image 2 in the drop-down list.

Start firmware update: Starts the firmware update.

Procedure

1. Click Select Firmware Image to select the firmware image to be uploaded.
2. Click Start firmware update to proceed.
3. Click Preserve all Configuration if you want to preserve all configuration settings during the firmware update and then click Proceed to Flash at the bottom to proceed.

Sign out

Protocol Type:

HTTPS

Update Type: BMC

☐ Preserve all Configuration. This will preserve all the configuration settings during the firmware update - irrespective of the individual items marked as preserve/overwrite in the table below.

All configuration items below will be preserved as default during the restore configuration operation. Click "Edit Preserve Configuration" to modify the Preserve status settings.

Edit Preserve Configuration

S.No	Preserve Configuration Item	Preserve Status
1	SDR	Overwrite
2	FRU	Overwrite
3	SEL	Overwrite
4	IPMI	Overwrite
5	NETWORK	Overwrite
6	NTP	Overwrite
7	SNMP	Overwrite
8	SSH	Overwrite
9	KYM	Overwrite
10	AUTHENTICATION	Overwrite
11	SYSLDG	Overwrite
12	WEB	Overwrite
13	REDFISH	Overwrite

Proceed to Flash

WARNING: Please note that after entering the update mode, the widgets, other web pages and services will not work. All the open widgets will be automatically closed. If the upgradation is cancelled in the middle of the wizard, the device will be reset only for BMC BOOT, and APP components of Firmware.

1. When the message requesting your confirmation prompts, click OK to proceed. The BMC will begin to verify and upload the firmware.

10.1.7.131 顯示 We will start the firmware upgrade now. You will not be able to access BMC until it flashes and restarts. Do you want to continue? 確定 取消

1. When the firmware is uploaded completely, check Full Flash in the Section Based Firmware Update field and then click Flash selected sections.

Note: If you only want to update the firmware for certain sections,

check the Upgradable/Non-Upgradable box for the individual sections instead of checking Full Flash.

Solid dark gray rectangle with no visible text, symbols, or features.

Section Name	Existing version	Uploaded version	Upgradable/Non- Upgradable
boot	13.1.000000	13.1.000000
conf	13.1.000000	13.1.000000
conf	13.1.000000	13.1.000000
ec	1.17.000000	1.17.000000
dtb	13.1.000000	13.1.000000
root	13.1.000000	13.1.000000
osimage	13.1.000000	13.1.000000
www	13.1.000000	13.1.000000
testapps	13.1.000000	13.1.000000
dre	13.1.000000	13.1.000000
ast2600e	13.1.33	13.1.33

Flash selected sections

WARNING: Please note that after entering the update mode, the widgets, other web pages and services will not work. All the open widgets will be automatically closed. If the upgrading is cancelled in the middle of the wizard, the device will be reset only for BMC BOOT, and APP components of Firmware.

1. When the message requesting your confirmation prompts, click OK. The BMC will start updating the firmware.

10.1.7.131 顯示 Clicking 'OK' will start the actual upgrade operation, where the storage is written with the new firmware image. It is essential that the upgrade operation is not interrupted once it starts. Do you wish to proceed? 確定 取消

1. A confirmation message will appear once the firmware has been successfully updated. Click OK to proceed.

10.1.7.131 顯示 firmware image has been updated successfully 確定

1. Click OK. The BMC will close all sessions displayed on the screen and automatically reboot the system.

10.1.7.131 顯示 Firmware reset has been called. Close the current session, and open a new session after a couple of minutes.

2-10-5 Preserve Configuration

Preserve Configuration allows users to preserve the existing configuration so that the current configurations on the BMC will not be overwritten during the firmware update process.

To open the Preserve Configuration page, click Maintenance > Preserve Configuration from the menu bar. A sample screenshot of the Preserve Configuration page is shown below.

MEGARAC SP-X 12.01.38 AVS 2021.MEGRAC SP-X File Online Quick Links... Dashboard Camera Zygkin Inventory File Information Logic & Resources Settings Remode Control Insight Realdehyde Power Control Maintenance Tag out Preserve Configuration Click here to go to Firmware Update or Recess Factory Defaults check All SDR FBS NEL iFree Network NTF SMADP SSH WNT Authentication Spiring Vitch Redfish USE - English APIs Network Admins Name - Maintenance - Purpose Configuration

The fields in the Preserve Configuration page are explained below.

Check All: Selects all items.

Save: Saves the changes.

Note: This configuration is used by Restore Factory Defaults process.

SDR

Following files will be preserved:

SDR.dat: This file contains the sensor data record information that is used in IPMI.

Dependency Configurations - NIL

FRU

Following files will be preserved:

FRU.bin: This file contains the logical field replaceable unit data that are used by IPMI.

Dependency Configurations - SDR

SEL

Following files will be preserved when Delete SEL reclaim space is disabled:

SEL.dat: This file contains the system event logs that are being logged by the IPMI.

Following files will be preserved when Delete SEL reclaim space is enabled:

Selreclaiminfo.ini - The file contains the SEL repository information.

SEL folder - This folder contains the multiple files of event logs.

Dependency Configurations - IPMI

IPMI

The following files are preserved in IPMI configuration:

IPMI.conf: This file contains the IPMI configurations such as SEL rep size, SDR rep size, interface specific, enable/disable, Primary/Secondary, IPMB Bus number etc.

Dependency Configurations - NIL

Network

To save network settings related with IPMI (LAN IP or DHCP configuration), select "IPMI" and "Network" options simultaneously. After restore configuration, the Network Configuration will be preserved successfully. Following files will also be preserved:

dhcp.conf: This file is to configure the host name in the FQDN format.

dns.conf: This file is used to configure the DNS registration method and DNS server for the particular interface, hostname: This file is used to store the Hostname of the BMC.

hostname.conf: This file is used to configure the host name creation method Manual/Automatic for the BMC.

Vlaninterfaces: This file helps to enable the vlan interface for the particular LAN interface

vlansetting.conf: This file is to store the vlan ID and Vlan priority for the particular VLAN interface entry.

bond.conf: This file is to enable the bond interface for the specified LAN interfaces.

Interfaces: This file is to configure the IP/IPV6 addresses for the LAN interface using static/DHCP method.

activeslave.conf: This file is to configure the active interface for the specified bond interface.

This file depends on bond.conf.

hosts: This file is used to store the host name to map the IP address.

hosts.allow: This file contains the list of hosts that has permission to access the system

hosts.deny: This file contains the list of host that does not allow accessing the system

resolv.conf: This file is used to store the nameserver and domain name for hostname registration.

dhcp6c-script: This file is used to configure the domain name, DNS server IPv6 address and NTP address.

dhcp6c.conf: This file is to configure the IPv6 parameters for the DHCPv6 clients.

ncsicfg.conf: This file is to configure the NCSI related configurations.

nsupdate.conf: This file is to configure the channel ID, package ID for the NCSI interface.

phycfg.conf: This file is to configure the link speed, duplex and MTU value for the specified interface.

dhcp.preip_4: This file is to store the pre IPv4 address. This file will be created at runtime.

dns.conf: This file is used to configure the DNS registration method and DNS server for the particular interface.

hostname: This file is used to store the Hostname of the BMC.

hostname.conf: This file is used to configure the host name creation method Manual/Automatic for the BMC.

Vlaninterfaces: This file helps to enable the vlan interface for the particular LAN interface

vlansetting.conf: This file is to store the vlan ID and Vlan priority for the particular VLAN interface entry.

bond.conf: This file is to enable the bond interface for the specified LAN interfaces.

Interfaces: This file is to configure the IP/IPV6 addresses for the LAN interface using static/DHCP method.

activeslave.conf: This file is to configure the active interface for the specified bond interface. This file depends on bond.conf.

hosts: This file is used to store the host name to map the IP address.

hosts.allow: This file contains the list of hosts that has permission to access the system

hosts.deny: This file contains the list of host that does not allow accessing the system

resolv.conf: This file is used to store the nameserver and domain name for hostname registration.

dhcp6c-script: This file is used to configure the domain name, DNS server IPv6 address and NTP address.

dhcp6c.conf: This file is to configure the IPv6 parameters for the DHCPv6 clients.

ncsicfg.conf: This file is to configure the NCSI related configurations.

nsupdate.conf: This file is to configure the channel ID, package ID for the NCSI interface.

phycfg.conf: This file is to configure the link speed, duplex and MTU value for the specified interface.

dhcp.preip_4: This file is to store the pre IPv4 address. This file will be created at runtime.

NTP

Following files will be preserved:

ntp.conf: This file contains the NTP dameon protocol configuration parameters such as synchronization sources, nodes and other related information

ntp.stat: This file contains the auto or manual network type protocols

adjtime: This file contains the time to synchronize the system clock

Localtime: This file is the system link to the file local time or to the correct time zone in the system timezone directly.

Dependency Configurations - IPMI

SNMP

Following files will be preserved:

snmp_users.conf: This file contains the SNMP user configurations such as user name and password encryption mechanism for the specific users.

snmpcfg.conf: This file contains the SNMP users privilege levels such as ro user and rw user.

Dependency Configurations - NIL

SSH

Following files will be preserved:

sshd_config: This file contains the keyword argument pairs of configurations such as Address family, Accept Env, Allow, users, authorized key files etc.

ssh_host_dsa_key, ssh_host_rsa_key: These files contain the private parts of the host keys.

ssh_host_dsa_key.pub, ssh_host_rsa_key.pub: These files contain the public parts of the host keys.

Dependency Configurations - NIL

KVM

Following files will be preserved:

vmedia.conf: This file contains the modes of media such as cd,fd,hd and enable and disable flags for lmedia, rmedia and sd servers.

stunnel.conf: This file contains the information about the stunnel configuration. It will also contain advisor and media server's secure port if secure connection is enabled.

usermacro.conf: This file saves the user defined macro from the jviewer.

rmedia.conf: This file contains the image name and the remote machine information like IP address, user name, password, domain name and share type.

Dependency Configurations - NIL

Authentication

Following files will be preserved:

activatedir.conf: This file contains the configurations such as sslenable, timeout, racdomain, adtype, adfilterdc1, adfilterdc2, adfilterdc3, username, password, and rolegroup information such as name domain and privileges.

openLdapGroup.conf: This file contains the oprnm ldap role group information such as name domain and privilege.

nsswitch.conf: This file contains the sources to obtain the name service information in the range of categories and in what order

pam_withunix: This file contains the PAM Order of modules such as IPMI, LDAP, RADIUS and UNIX.

pam_wounix: This contains the PAM Order of modules such as IPMI, LDAP and RADIUS.

group: This file contains the Linux group. It stores the group information or defines the user group information in Linux.

passwd: This file contains the user login information for the Linux system

shadow: This file contains the encrypted password information for the clients.

ldap.conf: This file contains the ldap server configuration details such as bindn, binpw, pam_password, nss_reconnect_tries, port, port secondary, host, host secondary.

radius.conf: This file contains the radius server IP address, port number, secret, timeout, privilege etc.

Dependency Configurations – NIL

Syslog

System Event Log

Web

Web Settings

Extlog

Audit Log & System Log

Redish

Redfish Audit Log

Procedure

1. Click Firmware Update or Restore Configuration to open the Firmware Update or Restore Configuration page accordingly.
2. Select Check All or the individual configuration items you want to preserve.
3. Click Save to save the changes.

2-10-6 Restore Configuration

This page allows you to restore the backup configuration files from the client system to the BMC. To open the Restore Configuration page, click Maintenance >Restore Configuration from the menu bar. A sample screenshot of the Restore Configuration page is shown below.

NEGARAC SP-X COLOR JUL 2021 NEWSPX5-8 FRC Host Online Quick Links... Defaultboard Sensor Systems Inventory File Information Logic & Network Settings Remarks Control Image Resources Power Control Maintenance Sign out Restore Configuration Config File Save USE - English Organic Mail switch Admins Home Maintenance Restore Configuration

The fields in the Restore Configuration page are explained below.

Config File: Select the file which was backup earlier.

Save: Confirms to upload the selected configuration file.

Procedure

1. Click Browse to search for the previously saved configuration file.
2. Click Save. A warning message will appear on the screen.

10.1.112.37 says: Click OK if you want to continue restoring configuraions WARNING:Restoring configurations will restart the device OK Cancel

1. Click OK to upload the new configuration file and the device will restart automatically.

2-10-7 Restore Factory Defaults

Restore Factory Defaults lists the configuration items that can be preserved during the restore process.

Warning: Please note that after entering restore factory widgets, all other web pages services will not work. All active widgets will be closed automatically. The device will and reboot within few minutes.

To open the Restore Factory Defaults page, click Maintenance >Restore Factory Defaults from the menu bar. A sample screenshot of the Restore Factory Defaults page is shown below.

NEGARAC SP-X 12.01.30 NPS NEGARAC SP-X Host Online Quick Links... Dashboard Sensor Hybridest inventory File information Logic & Resources Settings Remode Central Usage Redentextue Power Control Maintenance sign out Restore Factory Defaults The following checked configurations will be preserved through the restore operation. You can make changes to the tip in the reserve configuration page. SER FPU NEL IPMD Network NTP SMH0 SSH KVM Authentication Spiking Web Redfish USE - English Organic Networks Adminals Home - Maintenance - Reserve Factory Defaults

Procedure

1. Click Preserve Configuration to open the Preserve Configuration page, which is used to preserve the particular configuration so that the configuration will not be overwritten by the default configuration.
2. Select the individual configuration items you want to preserve.
3. Click Save to save the changes.

2-10-8 System Administrator

This page is used to configure the System Administrator settings.

To open the System Administrator page, click Maintenance > System Administrator from the menu bar. A sample screenshot of the System Administrator page is shown below.

MEGARAC SP-X URL: 2019-03-22 UK 2.2.61 (UFC-40380.047) User Interface Squark CAMEL Lastboard Server Symbol Inventory File Information Logic & Requests Settings Remode Control Image Maintenance Power Control Maintenance Sign out System Administrator User Name: system: Available User Accounts Change Password Password: Confirm Password Start

The fields in the System Administrator page are explained below.

Username: Displays user name of System Administrator. It is read-only.

Enable User Access: Enables user access for system administrator.

Change Password: Allows users to change the password.

Note: This field will not allow more than 64 characters.

Password must be at least 8 characters long and blank space is not allowed.

Save: Saves the new configuration for system administrator.

Procedure

1. Check Enable User Access to enable user access for system administrator.
2. Enable Change Password. This action enables the password fields.
3. Enter the password in the Password field.
4. Re-enter the password in the Confirm Password field.
5. Click Save to save the changes.

2-10-9 Sign Out

To log out from the Web GUI, click the admin on the top right corner of the screen. A sample screenshot of admin option is shown below.

admin - Administrator Profile Sign out

Click Sign Out to perform log out from the Web GUI. A Warning message will be prompted you to proceed further, click OK to log out else Cancel to retain the Web GUI.