MY Truck III - Browser NAVMAN - Free user manual and instructions

USER MANUAL MY Truck III NAVMAN

Important safety information

PLEASE READ CAREFULLY BEFORE INSTALLING PRODUCT IN VEHICLE

	This is the safety alert symbol. It is used to alert you to potential personal injury hazards. Obey all safety messages that follow this symbol to avoid possible injury or death.
	WARNING indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury.
	CAUTION indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury.
	CAUTION used without the safety alert symbol indicates a potentially hazardous situation which, if not avoided, may result in property damage.

WARNING

Removing original equipment, adding accessories or modifying your vehicle could affect the vehicle's safety or make it illegal to operate in some jurisdictions.

Follow all product instructions and all instructions in your vehicle owner's manual regarding accessories or modifications.

Consult your country's and/or state's laws regarding operation of a vehicle with any accessories or modifications.

It is your sole responsibility to place, secure and use your Navman in a manner that will not cause accidents, personal injury or property damage. Always observe safe driving practices.

Do not mount your Navman in a way that may interfere with the safe operation of the vehicle, the deployment of air bags or other safety equipment.

Do not operate your Navman while driving.

Before you use your Navman for the first time, familiarise yourself with your device and its operation.

On main roads, the distance to an exit calculated by your Navman may be further than the distance shown on road signs. Road signs show the distance to the start of an exit while your Navman shows the distance to the next intersection, i.e., the end of the exit ramp or road. To prepare to exit a road, always follow distance information on road signs.

The use of information regarding safety or speed camera locations may be subject to local laws in the country of use. You are responsible for checking that you can legally use the information in your country or in the country where the information will be used.

CAUTION

Do not handle your Navman while it is hot. Let the product cool, out of direct sunlight.

At full power, prolonged listening to your Navman via headphones or earphones can damage the ear of the user.

CAUTION

Do not expose your Navman to direct sunlight in an unattended vehicle for prolonged periods. Overheating may damage the unit and void warranty.

To discourage theft, do not leave your Navman, mounting bracket or any cables in plain view in an unattended vehicle.

Warning Notice to Drivers in the United States

State law may prohibit drivers in states such as Arizona, California and Minnesota from mounting objects on their windshields while driving. Please make sure you research and follow your most current State laws. An alternative mounting option may be provided in the box with your product; or see our website for additional mounting alternatives. Navman does not take any responsibility for any fines, penalties, or damages that may be incurred as a result of disregarding this notice.

Home charger-specific safety information

WARNING

To charge your Navman from the mains power, use the home charger (sold separately) supplied by Navman as an accessory. Using other home chargers with your Navman could result in serious injury or property damage.

Never use the charger if the plug or cord is damaged.

Do not expose the charger to moisture or water. Do not use the charger in a high moisture environment. Exposure to water may cause electrical sparks or fires.

Never touch the charger when your hands or feet are wet.

Allow adequate ventilation around the charger when using it to operate your Navman or charge the internal battery. Do not cover the charger with paper or other objects that will reduce ventilation. Do not use the charger while it is inside a carrying case or other container.

Ensure that the charger is connected to a power source with the correct fitting and voltage requirements. The voltage requirements can be found on the home charger casing and/or packaging.

Do not attempt to service the charger as this could result in personal injury. Replace the charger if it is damaged or exposed to excess moisture.

Internal battery-specific safety information

WARNING

Your Navman contains a non-replaceable internal lithium-ion battery. The battery may burst or explode if mishandled, releasing hazardous chemicals. To reduce the risk of fire or burns, do not disassemble, crush or puncture the battery.

Recycle or dispose of the battery safely and properly according to local laws and regulations. Do not dispose of the battery in fire or water.

About the battery

■ Use a specified battery in the equipment.
■ CAUTION: The battery can burst or explode, releasing hazardous chemicals. To reduce the risk of fire or burns, do not disassemble, crush, puncture, or dispose of in fire or water.
■ Important instructions (for service personnel only)

■ Caution: Risk of explosion if battery is replaced by an incorrect type. Dispose of used batteries according to the instructions.
■ Replace only with the same or equivalent type recommended by the manufacturer.
■ The battery must be recycled or disposed of properly.
■ Use the battery only in the specified equipment.

CAUTION

Only use the correct home charger (sold separately), usb cable or in-car charger supplied by Navman to charge your Navman internal battery.

Only use your Navman internal battery with your Navman unit.

The Navman battery will stop charging when the ambient temperature is less than 0^ C ( 32^ F) or more than 45^ C ( 113^ F).

Failure to adhere to these warnings and cautions may lead to death, serious injury or p disclaims all liability for installation or use of your Navman that causes or contributes to death, injury or property damage or that violates any law.

Compliance

WARNING: This product, its packaging and its components contain chemicals known to the State of California to cause cancer, birth defects or reproductive harm. This Notice is being provided in accordance with California's Proposition 65.

For regulatory identification purposes: MY ESCAPE II / MY TRUCK is assigned a model name of N382.

Marking labels located on the exterior of your Navman indicate the regulations that your model complies with. Please check the marking labels on your Navman and refer to the corresponding statements in this chapter. Some notices apply to specific models only.

The user needs to switch off the Navman when exposed to areas with potentially explosive atmospheres such as petrol stations, chemical storage depots and blasting operations.

Bluetooth

Bluetooth®

Bluetooth QD ID B018159

WEEE

This product must not be disposed of as normal household waste, in accordance with the EU directive for waste electrical and electronic equipment (WEEE - 2002/96/EC). Instead, it should be disposed of by returning it to the point of sale, or to a municipal recycling collection point.

Important safety information 2

Home charger-specific safety information.... 3

Internal battery-specific safety information.... 3

Compliance 4

Bluetooth....4

WEEE....4

Contents 5

Welcome....6

Important information for using the manual....6

Disclaimer....6

Mounting your Navman in a vehicle 7

Enabling Traffic (TMC) Reception....8

Getting to know your Navman....9

How do I turn on my Navman? 10

Using the power switch 10

How do I charge the battery?......11

How do I charge the battery in a vehicle? 11

How do I charge the battery via my computer? 11

How do I charge the battery at home or work? 11

How do I insert a memory card? 12

How do I connect my Navman to my computer? 13

Other features 14

How do I make a hands-free call? 14

How do I search for a place using Live Local Search? 14

How can I play external AV equipment through my Navman? 14

Reference 15

What is GPS? 15

How does my Navman receive GPS signals? 15

Caring for your Navman....15

Troubleshooting 16

Navman Customer Support....16

Thank you for purchasing this Navman. Please read this manual carefully before using your Navman for the first time. Keep this manual in a safe place and use as your first point of reference.

Important information for using the manual

It is important to understand the terms and typographical conventions used in this manual.

Formatting

The following kinds of formatting in the text identify special information:

Convention Type of Information
Bold	Components or items displayed on screen, including buttons, headings, field names and options.
Italics Indicates	the name of a screen.

Icons

The following icons are used throughout this manual:

Icon Description
	Note
	Tip
	Warning

Terms

The following terms are used throughout this manual to describe user actions.

Term Description
Press Press and	release a button quickly.
Tap Press and	release an item displayed on the touch screen.
Select Tap an	item in a list or tap a command from a menu.

Disclaimer

Not all models are available in all regions.

Depending on the specific model purchased, the colour and look of your device and accessories may not exactly match the graphics shown in this document.

Navman operates a policy of ongoing development. Navman reserves the right to make changes and improvements to any of the products described in this document without prior notice. Navman does not warrant that this document is error-free. The screenshots and other presentations shown in this manual may differ from the actual screens and presentations generated by the actual product. All such differences are minor and the actual product will deliver the described functionality as presented in this User Manual in all material respects.

Mounting your Navman in a vehicle

CAUTION:

• Never mount your Navman where the driver's field of vision is blocked.
• If the windscreen is tinted with a reflective coating, it may be athermic and impact the GPS reception. In this instance, please mount your Navman where there is a “clear area” - usually just beneath the rear-view mirror.
• To protect your Navman against sudden surges in current, connect the in-car charger only after the car engine has been started.
• Never expose your Navman to extreme heat or direct sunlight for prolonged periods. Overheating may damage your Navman.

Enabling Traffic (TMC) Reception

Traffic information is not available on all models and is only available in selected countries.

Depending on the model of your Navman you can receive live traffic information via the in-car charger which is used as an antenna. Please ensure your car charger is connected to your Navman and power source to receive TMC live traffic information.

Please note that you will not be able to receive the traffic information while using the third-party accessory (such as your own car charger).

For information on using traffic information on your Navman, see the Software User Manual.

Getting to know your Navman

Close-up of a computer mouse with two buttons labeled 1 and 2 (no text or symbols beyond labels)

NAVMAN 7 6

Top-down view of a curved electronic device with labeled component '8' (no text or symbols beyond label)

NAV/MAN ③ ④ ⑤

Item	Description
1	Power button
2	Slot for microSD memory card
3	Cradle slot
4	Screw holes for securing the cradle
5	Speaker
6	Touch screen
7	Microphone (not on all models)
8	Connector for in-car charger, USB cable, home charger* and TMC accessory kit** may be sold separately

How do I turn on my Navman?

Using the power button

■ To turn on your Navman, press the Power button.
■ To turn off your Navman, press the Power button briefly and then tap Sleep.

Your Navman will enter a suspended state. When you next turn it on, your Navman will return to the last screen that you used.

■ To lock the screen, press the Power button briefly and then tap Lock.

To unlock the screen, press the Power button briefly and then tap Unlock.

■ To turn off your Navman, press and hold the power button for 3 seconds.

3 sec

How do I charge the battery?

Your Navman has an internal battery that when fully charged, should provide power for up to 2 hours. The battery can take up to 4 hours to fully charge.

The battery may not be fully charged when you use your Navman for the first time.

CAUTION: For optimal performance of the battery, note the following:

• Do not charge the battery when the temperature is high (e.g. in direct sunlight).
  ■ There is no need to fully discharge the battery before charging.
• When leaving your Navman for long periods, slide the power switch to the RESET position to save internal battery power.
  ■ Fully charging the battery once per month will help the device retain GPS fix.

How do I charge the battery in a vehicle?

To charge your Navman in a vehicle, plug the in-car charger into 🐘 on the attached cradle and the other end into the vehicle power socket.

How do I charge the battery via my computer?

1. Turn on your computer.
2. Plug the large end of the USB cable directly into a USB port on your computer (not a USB hub) and plug the small end into 🐘 on the bottom of your Navman.

For optimal charging results, ensure that your Navman is out of its cradle and turned off while connected our computer.

How do I charge the battery at home or work?

You can use an optional home charger to charge the battery.

To charge your Navman using a mains power socket, plug the home charger cable into 🐘 on the bottom of your Navman and the mains power charger into the power socket.

The home charger is not included and may be purchased separately. Visit www.navman.com.au (Australia) www.navman.co.nz (New Zealand) for details.

How do I insert a memory card?

Close-up of a black remote control with a USB flash icon and orange arrow indicating compression (no text or symbols)

1. Open the cover on the top of your Navman to locate the memory card slot.

2. Hold the microSD card by the edges and gently insert it into the slot as shown in the above diagram of your Navman.

Do not apply pressure to the centre of the memory card.

1. To remove a card, gently push the top edge of the card inwards to release it, then pull it out of the slot.

How do I connect my Navman to my computer?

1. Turn on your computer.

2. Plug the large end of the USB cable directly into a USB port on your computer (not a USB hub) and plug the small end into 📧 on the bottom of your Navman.

Diagram showing cable connection between a remote device and a computer via USB port, with an orange arrow indicating the cable's connector.

1. When your Navman is turned on and connected to the computer, you can select the desired connection type from the pop-up message screen:

2. Charge only: You will be able to continue using your Navman with the battery in charging mode via the computer.

3. Computer: Your Navman will be recognised as an external mass-storage device named by the model name. A USB Connection screen appears to prevent you from using your Navman.

4. When you select the Computer option, you can use Windows File Explorer to copy/move the files from the computer to your Navman.

Before disconnecting your Navman from the computer, it is recommended to safely remove the USB drive from the system. This prevents data loss on the device.

WARNING: DO NOT delete any files that are pre-installed on the device. Deleting the files can cause the device to crash. Navman is not responsible for product quality caused by file deletion.

How do I make a hands-free call?

Hands-free calling is not available on all models.

If you have a compatible mobile phone with Bluetooth wireless technology, you can use your Navman as a hands-free car kit. Before you can use this feature you must pair your mobile phone with your Navman.

Ensure that the Bluetooth wireless feature of your mobile phone is turned on before you begin pairing. Not all phones with Bluetooth wireless technology are compatible with your Navman. For a list of compatible phones, visit www.navman.com.au (Australia) or www.navman.co.nz (New Zealand).

How do I search for a place using Live Local Search?

Live Local Search is not available on all models and is only available in selected countries.

Using Live Local Search, you can search online for places near a specific location. For information about Live Local Search and using Bluetooth wireless, refer to the Software User Manual.

To use Live Local Search, you must pair your Navman with your mobile phone. If your Navman isn't paired with your mobile phone, then the Bluetooth screen will display. Not all phones with Bluetooth wireless technology are compatible with your Navman. For a list of compatible phones, visit www.navman.com.au (Australia) or www.navman.co.nz (New Zealand).

How can I play external AV equipment through my Navman?

The AV IN connector is not available on all models.

Your Navman can receive AV input from external equipment, such as a DVD player. This means that you can use your Navman as a second screen.

WARNING: Your Navman MUST NOT be used to play video when driving. Using this feature may cause an accident. Please make sure you comply with this warning. Navman accepts NO liability whatsoever in this regard.

Connect the video (yellow) and audio (red and white) signal ends of the supplied AV cable to the AV output connectors on the external video device. Then connect the other end of the AV cable to the AV IN connector on your Navman. Please ensure that your external video device's AV out feature is enabled.

Diagram showing a device with an attached cable and connected to a laptop (no text or symbols visible)

For more information about playing external AV equipment via your Navman, refer to the Software User Manual.

What is GPS?

The Global Positioning System (GPS) is available at any time, free of charge, and is accurate to within 5m (15ft). GPS navigation is made possible by a network of satellites that orbit the Earth at around 20,200km (12,552mi). Each satellite transmits a range of signals which are utilised by GPS receivers, such as your Navman, to determine an exact location. Although a GPS receiver can detect signals from up to 12 satellites at any time, only four signals are required to provide a position or "GPS fix" (latitude and longitude), for vehicle navigation systems.

How does my Navman receive GPS signals?

Your Navman receives GPS signals via the internal GPS antenna. To guarantee the optimum GPS signal strength, ensure your Navman is outdoors, or in a vehicle outdoors, and has an unobstructed view of the sky. GPS reception is not usually affected by weather, however, very heavy rain or snow may have a negative effect on your reception.

Illustration of a car with signal waves and a satellite, no text or symbols present

GPS

To obtain a faster GPS fix, ensure car is stationary and battery is fully charged once per month.

Caring for your Navman

Taking good care of your Navman will ensure trouble-free operation and reduce the risk of damage to your Navman:

• Keep your Navman away from excessive moisture and extreme temperatures.
• Avoid exposing your Navman to direct sunlight or strong ultraviolet light for extended periods of time.
  ■ Do not place anything on top of your Navman or drop objects on your Navman.
• Do not drop your Navman or subject it to severe shock.

• Do not subject your Navman to sudden and severe temperature changes. This could cause moisture condensation inside the unit, which could damage your Navman. In the event of moisture condensation, allow your Navman to dry out completely before use.
  The screen surface can easily be scratched. Avoid touching it with sharp objects. Non-adhesive generic screen protectors designed specifically for use on portable devices with LCD panels may be used to help protect the screen from minor scratches.

• Never clean your Navman when it is turned on. Use a soft, lint-free cloth to wipe the screen and the exterior of your Navman.

• Do not use paper towels to clean the screen.
• Never attempt to disassemble, repair or make any modifications to your Navman. Disassembly, modification or any attempt at repair could cause damage to your Navman and even bodily injury or property damage and will void any warranty.
• Do not store or carry flammable liquids, gases or explosive materials in the same compartment as your Navman, its parts or accessories.

Troubleshooting

If you encounter a problem you cannot solve, contact an authorised service centre for assistance.

Problem Steps to Take and	things to check What Next?
The unit is not turning on/charging	Try to charge the unit through a USB cable connected to a computer. If the unit charges then the issue is with the in car charger. If the unit still fails to charge, then the fault is with the unit.	Contact technical support and an RMA will be created to fix the unit or replace the in car charger.
I can not get a GPS Signal	Make sure you are stationary and have a clear line of site to the sky. If this fails to resolve the issue, please reset the GPS chip through the Settings menu of your unit.	If the fault is still not resolved, please visit our self help site (see the information below), or contact our technical support team.
My unit is always showing that the speed limit is 110 kph even when it is not	The units are set at a manual speed limit defaulted at 110 kph. This can be changed through the 'Safety' section of your 'Settings' menu.	If the fault is still not resolved, please visit our self help site (see the information below), or contact our technical support team.
Where is my product key? I want to activate my unit.	There is no need to activate your unit in anyway. This Activation tab within the NavDesk software is for subscriptions, travel books, international maps and map upgrades only. Your unit will work straight out of the box and there is no need to activate it in anyway.	If the fault is still not resolved, please visit our self help site (see the information below), or contact our technical support team.

Navman Customer Support

To report a faulty product or speak to a member of our Technical Support team, contact:

Australia: 1300 NAVMAN (628626), New Zealand: 0800 GONAVM (466286);

or visit our tech support Website: www.navmansupport.com.au (Australia), www.navmansupport.co.nz (New Zealand).

MY ESCAPE II / MY TRUCK

Software User Manual

Contents 2

How do I get started? 5

How do I use the touch screen? 6

Navigating on the screen 6

Main Menu....7

How do I navigate through the menu screens? 8

How do I use the Keyboard screen? 9

How do I go from A-B? 10

How do I use the FIND wizard?......10

How do I plan my first trip?....11

How do I preview the destination on map? 12

How do I preview a route? 13

How do I change the navigation mode? 14

Large Vehicle mode 14

Professional Truck mode 15

Pedestrian mode 15

How do I view my route? 16

How do I select the route type using Trip Select? 16

The driving map....16

How do I change the route configuration? ....17

How do I view my route statistics?......18

How do I adjust the volume? 18

How do I zoom in/out the map? 19

How do I view the traffic status on my route? 19

Advanced Routing Functions 20

How do I create a trip with multiple stops? 21

How do I capture a location or a journey? 23

How do I capture the GPS co-ordinates of my location? 23

How do I capture a journey? 23

How do I navigate to a location I have captured? 24

How do I navigate to the saved car location? 24

How to view a journey I have captured? 24

My Places 25

How do I save a location as My Place or Home? 25

How do I navigate to a location I have saved? 25

How do I navigate to Home? 26

How do I navigate to a recent place? 26

How do I edit a saved location in My Places? 26

How do I navigate to a NavPix™? 27

How do I search for a POI? 29

How do I find the nearest POIs using EXPLORE? 29

How do I find the nearest POIs using the POI category buttons? ....31

How do I search for a POI by type? 32

How do I search for a POI by Smart Find Keyword? 34

How do I receive current traffic information via TMC? 36

How will I know when a Traffic Event occurs? 36

Traffic overview screen....37

How do I view a list of all events on my route? 37

How do I view traffic details?......38

Traffic messages....39

Traffic preferences 40

What is Travel Book? 41

How do I search for a POI in a city I am visiting using travel guides? ....41

How do I play videos on my Navman via AV IN? 42

How do I make a hands-free call? 43

How do I pair my Navman with a Bluetooth device? 43

How do I make a phone call? 45

How do I view my call history? 47

What is NAVMAN CONNECT?......48

How do I search for a POI using Google Local Search? 48

How do I search for a POI using TrueLocal.com.au? 49

How do I receive weather information using NAVMAN CONNECT? ....50

How do I search for roadside assistance? 51

How do I control my Navman using Voice Command? 52

How do I plan my route using Voice Command? 52

How do I answer an incoming call using Voice Command? 52

What can I customise? 53

Audio....53

Screen 54

Safety....54

Route options 55

Map display ....57

My Maps....57

Language 58

Answer calls by voice 58

Units....59

Time Zone....59

Bluetooth....60

Trip Meter 60

Device....61

Demo 62

Help....62

What is NavDesk?......63

How do I install NavDesk onto my computer?......63

How do I get started? 64

My Subscriptions....66

My Maps....67

VOICE COMMAND....69

Custom POIs 70

Photo Album....72

Image Search....76

Application Gallery....77

Unlock Features....78

My Places....78

TRIP PLANNER....80

MY NAVMAN....82

CONNECT 86

For more information....88

Online support 88

Navman Customer Support......88

Speed Limit 88

Safety Camera POIs 88

Point of Interest categories 88

Traffic and other TMC Events 91

Third party recipient terms and conditions....92

Copyright 93

To get started for the first time, complete the following steps:

1. Read the Important Safety Information
2. Position your Navman in your vehicle

Follow the instructions in the Quick Start Guide.

CAUTION: Ensure that your Navman does not obstruct the driver's view, or interfere with the operation of the vehicle airbags and safety devices.

1. Turn your Navman on

Your Navman will turn on and display the Language screen.

1. Select your preferred language

From the Select Language screen, tap your preferred language.

- You can change your preferred language while using your Navman.

1. Read the warning message

The Safety Agreement screen will display after you have selected your preferred language. Read the Safety Agreement message. To confirm that you have read and understood the message, tap Accept.

1. View the Tutorial

- To move forward through the Tutorial screen, tap Next. To view the previous screen, tap

■ To skip the Tutorial screen, tap Skip.

To prevent the Tutorial from displaying on each start-up, tap the Show tutorial on start-up option to

deselect it. To enable the tutorial again, select the option from Main Menu → Help → View Tutorial.

1. Customise the device

Follow the onscreen instructions to select your preferred distance unit, date format, time format, and map set.

You will have to do this only the first time you use your Navman. You can change these settings while

using the device by tapping Main Menu → 📋. For more information, refer to the "What can I customise?" section.

1. Set up Home

The Home setup wizard only appears on the first time you start your Navman.

• Tap OK to set up your home immediately using the address-entry wizard.
• You can tap Cancel to skip the wizard, and then select you home later in MY PLACES.

When you have finished the steps above, the Main Menu screen will display. If you have a GPS fix, you can start to use Navman to plan your trip.

The first time you use your Navman it may take several minutes to establish a GPS connection.

How do I use the touch screen?

Navigating on the screen

To operate your Navman, touch the screen with your fingertip. You can perform the following actions:

Tap

Press and release an item displayed on the touch screen.

- Select

Tap an item in a list or tap a command from a menu.

08:46 Fri, 11/06/12 FIND MAP PLACES EXPLORE TRAFFIC SETTINGS CO

Main Menu

The Main Menu is your starting point for searching for a destination. The Main Menu also allows you to customise your Navman, view saved locations as My Place/Home, and search for POIs nearby, and so on. Menu display may differ from the below, depending on your region, maps installed or model of Navman.

08:46 Fri, 11/08/12 FIND MAP MY PLACES EXPLORE TRAFFIC SETTINGS VOICE COMMAND

Not all features are available on all models.

Tap to show the next page of Main Menu.

Search for places, areas and streets to help plan your route.

Access your saved locations.

Receive live traffic information on your route and set traffic preferences.

Control your Navman by voice, allowing you to search address/place/POI easily.

Use your Navman as a hands-free car kit.

Record GPS co-ordinates of a location or a journey.

Select your navigation mode: Car, Large Vehicle, Professional Truck, or Pedestrian.

Search for information and POIs using Lonely Planet Scenic Tours or Travel Guides.

Search online for live POI information using Google™ Local Search.

Switch to AV mode to receive the video signal from the external AV device.

Set or navigate to your home address.

Search for the nearest emergency services, including hospitals and police.

Display the Map screen.

Explore the area around your current position or destination.

Configure your Navman to enhance your navigation experience.

Add or begin a planned trip with multiple waypoints.

Display the calculated route in simulation mode.

Set your Navman to avoid the Four-wheel tracks or not, and to display/hide the POIs along the Four-wheel tracks on map.

Search for information and POIs for the city you are visiting using Cityseekr Travel Guides.

Search for restaurants, accommodation, wineries, bars, and more using AGFG* (Australian Good Food Guide).

* For selected models only.

Search online for live POI information (using TrueLocal.com.au) and latest weather information.

Get help with just a phone call once you breakdown on the road.

Search for the nearest petrol stations.

Search for the nearest restaurants, cafes, fast-food premises and other dining establishments.

Search for the nearest hotels/motels.

Search for the nearest parking places.

Search for the nearest banks and ATMs.

How do I navigate through the menu screens?

How do I use the BACK button and MAIN MENU button in the title bar?

1. On the Main Menu screen, tap the desired menu button to enter the menu screen.

For example, tapping will lead you to the FIND screen.

FIND Smart Find Keyword Address City/Area Coordinates Postcode Intersection Points of Interest Recent Locations

1. The system provides the BACK button (←) and MAIN MENU button (in the title bar of the menu screen, which allow you to navigate through the menu screens easily.

You can:

■ Return to the previous screen by tapping the BACK button.
- Return to the Main Menu by tapping the MAIN MENU button.

In some menu screens, the MAIN MENU button will not appear in the title bar. In this instance, you have to tap the BACK button twice.

How do I use the tabs in the title bar?

In some menu screens, such as the map Overview screen, the system provides the tab buttons in the title bar that allow you to enter the additional page in the menu screen.

Simply tap the desired tab to change the view. The selected tab will be highlighted as a darker-colour tab.

Overview M29 M10 M20 43 Melbourne

Information Time to next destination 7 min Distance to go 6.9 km Estimated Time of Arrival 8:53 am TTD for the journey 32 min DTG for the journey 19.1 km

How do I use the Keyboard screen?

The Keyboard screen will display when you are required to enter text, such as when searching for a street name. Search results will be listed in matching order, with the closest matches appearing on the screen. A maximum of 99 results will display.

The Keyboard screen can display with various layouts depending on the information you need to enter, including alphabet, number, alternate characters and combinations of these.

Enter keywords Q W E R T Y U I O P A S D F G H J K L Z X C V B N M 123

→

Sydney q w e r t y u i o p a s d f g h j k l z x c v b n m 123 OK

How do I enter characters/numbers?

■ To select a character, tap the character.
■ To delete a character, tap

Tap and hold

lete the entire text.

■ To enter numbers, tap

How can I set my keyboard preference?

1. From the Keyboard screen, tap 📄. The Keyboard preference screen will display.
2. Select the preferred keyboard type from the list.

How do I go from A-B?

WARNING: For your safety, enter destination information before you start a journey. Do not enter a destination while driving.

How do I use the FIND wizard?

Your Navman is equipped with maps that provide street-level detail for door-to-door navigation, including Points of Interest such as accommodation, parking areas, petrol stations, railway stations and airports. The FIND wizard allows you to search the location easily.

1. On the Main Menu, tap

to display the FIND screen.

FIND screen display and the order of the options may differ from the below, depending on your region, maps installed or model of Navman.

FIND Smart Find Keyword Address City/Area Coordinates Postcode Intersection Points of Interest Recent Locations

2. Complete the following:

If you want to ... Then ...
search all information on the device - city, streets, named sites, features, landmarks or venues,	tap
search for an address,	tap
search for a city/area,	tap
search for a location using a GPS coordinate,	tap
search a location by postcode,	tap
search for a street intersection,	tap
search for a Point of Interest,	tap
navigate to a recently visited location,	tap

For further instructions on searching for a POI, refer to the "How do I search for a POI?" section.

How do I plan my first trip?

Menu display may differ from the below, depending on the model of Navman.

Using your Navman to plan your first trip is easy. There are several ways to select your destination. The following steps will show you how to plan your route by searching the address.

1. On the Main Menu, tap the FIND address wiza

Complete the following to navigate to a street address that you know using

08:46 Fri, 11/08/12 FIND MAP MY PLACES EXPLORE TRAFFIC SETTINGS VOICE COMMAND

→

FIND Smart Find Keyword Address City/Area Coordinates Postcode Intersection Points of Interest Recent Locations

Enter a city/area Q W E R T Y U I O P A S D F G H J K L Z X C V B N M 123

→

Enter street name Q W E R T Y U I O P A S D F G H J K L Z X C V B N M 123

Enter Number ( 1 - 7 ) 1 2 3 4 5 6 7 8 9 0 Centre of Street

→

Destination Elizabeth St Preston, Victoria 3072 Australia 8.3 km / 14 min Explore Save GO

2. On the Destination screen, complete the following:

If you want to ... Then ...
calculate the route and start navigating,	tap ↻.▪ The Map screen will display.
save the location as a favourite,	tap ♥+..▪ The location will be saved in My Places immediately.
save the location as Home,	tap ♥+ → ♥ → ♗+.
explore the map,	tap 🔍.

How do I preview the destination on map?

After searching an address (or a POI), you can preview the destination on map to explore the area near the location.

1. On the Destination screen, tap the button to display the destination preview map as below.

Destination Elizabeth St Preston, Victoria 3072 Australia 8.3 km / 14 min Explore Save GO

1. The destination Preview map screen will display.

Elizabeth St, Preston, Victoria 3072, Australia

On the Preview map screen, you can:

• Tap the + / - button to zoom in/out the map.
  ■ View the information of your destination that is shown at the top of the Map screen.
• Tap on a street/area/POI to display the related information of the location near your destination.
• Tap the grey arrow icon ( ) to display your current position on the map.

- Tap on the map to select the other destination. The information of the selected street/area/POI near your destination will be displayed. Tapping the check mark will bring up the Destination screen of the selected location.

De Chene Reserve, Bell St (40), Coburg, Victoria 3058, Australia

→

Park and Recreation Area De Chene Reserve Bell St (40) Coburg, Victoria 3058 Australia 8.3 km / 14 min Explore Save GO

How do I preview a route?

Route demonstration allows you to:

■ preview a route.

■ plan and view a route without a GPS fix, such as when you are inside a building.

The following steps will show you how to preview a route.

1. On the Main Menu, tap

1. Select a departure point through the Leaving from screen.

If you have a GPS fix, you can simply select the Here button ( ) so that you do not need to select a departure point. Otherwise, use the FIND address wizard, Explore map, My Places/Recent places menu or Home to set the departure point if you want the demonstrated route to start elsewhere.

1. Select a destination point through the Going to screen. When done, tap

1. The Map screen will display the calculated route in route simulation mode. Select a route type and tap and the route demonstration will start automatically.

Right Flora St 110 m 9.7 DTG km 50 Jim Rd 193 Milburn Rd

The simulated route will be displayed as orange colour.

How do I change the navigation mode?

Depending on your vehicle type, you can set the navigation mode as Car, Large Vehicle, Professional Truck, or Pedestrian mode.

The Large Vehicle mode and Professional Truck mode are specifically designed for large vehicles. With the input of your vehicle or trailer details, the mode enables to calculate safer and more efficient routes to avoid the length/width/height/weight restricted tunnels and bridges, as well as sharp turns and narrow country lanes.

When in Large Vehicle/Professional Truck mode, your route will be displayed using icon on the Map screen.

WARNING: Do not rely solely on this product and its features. Using this product does not change the requirement for a driver to take full responsibility for his behaviour. This responsibility includes observing all traffic rules and regulations in order to avoid accidents, personal injury or property damage.

The Pedestrian mode allows you to navigate to your destination using roads and paths appropriate for a pedestrian, including road where driving may be prohibited (like pedestrian zones for example). When in Pedestrian mode, you will not be routed onto motorways and their associated on/off ramps (slip roads). If your destination is more than 10 kilometres (6.3 miles) away, a warning message is displayed indicating that the route is a long way to walk.

When in Pedestrian mode, your route will be displayed using 📁 icon on the Map screen.

Large Vehicle mode

1. On the Main Menu, tap the Mode button.
2. If your vehicle is up to 9 tones, select the Large Vehicle option.
3. Complete the following:

If you want to ... Then ...
set the details for your truck, enter the following data of the truck:▪ total truck weight (< 9.0 tones)▪ maximum axle weight (< 9.0 tones)▪ total truck length (< 15.0 meters)▪ maximum truck width (< 2.5 meters)▪ maximum truck height (< 4.6 meters)You must complete the details of the truck settings before you can use Large Vehicle mode to plan your route.
set how you want to receive the speed limit alerts,	tap Speed limit display / Speed limit alerts to turn it on or off.

Professional Truck mode

1. On the Main Menu, tap the Mode button.

2. If your vehicle is up to 65 tones, select Professional Truck option.

3. Complete the following:

If you want to ... Then ...
set the details for your truck, enter the following data of the truck:▪ total truck weight (< 65.0 tones)▪ maximum axle weight (< 50.0 tones)▪ total truck length (< 30.0 meters)▪ maximum truck width (< 2.5 meters)▪ maximum truck height (< 4.6 meters)You must complete the details of the truck settings before you can use Professional Truck mode to plan your route.
limit the route planning while shipping hazardous materials in the truck,	tap Hazmat (Hazardous Materials) and then select the correct option from the list.
drive the road train type vehicles,	tap B-Double to turn it on or off.
set how you want to receive the speed limit alerts,	tap Speed limit display / Speed limit alerts to turn it on or off.

Pedestrian mode

1. On the Main Menu, tap the Mode button.
2. Tap Pedestrian.

How do I view my route?

How do I select the route type using Trip Select?

By default setting, your Navman will display the Trip Select screen when you tap after your search. All of the four route types (Fastest, Economical, Easiest, and Shortest) will be calculated and displayed in different colours.

When route calculation is completed, you can select one and tap to start navigating.

Brunswick St on St + Yt Brunswick 55 Parkville Melbourne 31 Mc Nort stte 38 Fitzroy North Clifton Hill 46 Fitzroy 45 Melbourne 32 Richmond 36 Fairfield Alphing 21 Economical 7.2 km 14 min 8.0 km 15 min Easiest 7.2 km 14 min Shortest 7.1 km 15 min GO Fastest 7.2 km 14 min

For more information about setting the preferred route type, refer to the Route Options section in "What can I customise?"

The driving map

When you select a route type and tap 📁, the Map screen will display. You will be directed to your destination by spoken and visual instructions.

The driving map will be displayed automatically when:

• a route is calculated and selected.
  ■ the device is reset and the user is on a route.

Alternatively, you can access the Map screen manually by tapping 📋 on the Main Menu.

Continue M79 (City) 800 m 18.0 DTG km Fullarton Rd MBD Fosters Rd 40 TransLink Dr 39 Ely Ct Keilor Park Dr Hanslnd Rd Old Calder Hwy 80 Concorde Dr 40 (Calder Fwy)

Item	Description
1	Direction and distance of next turn	The direction and distance to your next turn.▪ Tap [icon: 3] to repeat the vocal instruction.
2	Current route Your current route is highlighted.
3	Current position	Your current position is marked with [icon: 1].
4	Address bar The current address will be displayed in the text box at the bottom of the Map screen.
5	Distance and time information	Tap to expand and select the following options:▪ DTG (Distance to Go)▪ TTG (Time to Go)▪ km/h or mph (speed) and compass heading▪ ETA (Estimated Time of Arrival)▪ Time

Depending on your driving route, you may see some icons that provide different information on your Map screen. Please note that these icons will not be always displayed during your journeys.

For example: the Speed Limit icon (100) on the Map screen. The Speed Limit icon shows the speed limit of the current road. If greyed out, you are below this speed limit. When over set limit, you will be warned with an audible and visual warning.

How do I change the route configuration?

Tap anywhere on the Map screen to bring up the Map options screen, which allows you to change the route-related configuration.

Map options Volume Add Waypoint Skip Waypoint Detour Zoom Route Cancel Route Route options

For more information about changing the route configuration, refer to the following sections in this manual.

How do I view my route statistics?

1. From the Map options screen, tap

1. Tap the tabs in the title bar to view the additional information in the different screens.

Overview A79 M10 M80 M1 Melbourne 30

Information Time to next destination 7 min Distance to go 6.9 km Estimated Time of Arrival 8:53 am TTD for the journey 32 min DTG for the journey 19.1 km

Turns 3.9km Continue: M79 (City) 1.8km Exit left 290m Second exit: Fullarton Rd 260m Third exit: Keilor Rd 500m Destination: BP

1. Your Navman provides information on your:

■ time to destination
■ time taken for trip
- distance to go
■ stationary time
■ estimated time of arrival
■ TTD/DTG/ETA for the journey*
- distance travelled
■ Traffic delay*

* Depending on the route calculated, you may see more information on the screen such as the estimated time/distance to the next stop when your trip contains multiple waypoints and the traffic delay information if a traffic event occurs in your trip.

How do I adjust the volume?

1. From the Map options screen, tap

1. The volume buttons will be displayed on the Map screen in translucent mode.

Exit left 37 (Airports) 1.8 km 14.6 DTG km 100 hotts Rd Kittyhawk Ct Wyong St

1. Complete the following:

If you want to ... Then ...
increase/decrease the volume,	tap ▪ The volume bar indicates the current volume level.
mute/unmute,	tap ▪ The speaker icon indicates the status: : muted : unmuted

The volume buttons will automatically disappear after the map is idled for 5 seconds.

How do I zoom in/out the map?

1. From the Map options screen, tap

1. The zoom buttons will be displayed on the Map screen in translucent mode.

Continue M79 (City) 1.5 km 18.6 DTG km 39 40 Dil Calder Hwy Concorde Dr Harrick Rd 80 40 (Calder Fwy)

1. Complete the following:

If you want to ... Then ...
zoom in the map,	tap and hold
zoom out the map,	tap and hold

The zoom buttons will automatically disappear after the map is idled for 5 seconds.

How do I view the traffic status on my route?

Traffic information is not available on all models and is only available in selected countries.

On the Main Menu, tap

The Traffic screen will be displayed.

For more information, refer to the "How do I receive current traffic information via TMC?" section.

Advanced Routing Functions

Smart Route

Your Navman features Smart Route, which intelligently anticipates congested roads at peak times so that they can be avoided. Smart Route does this by using historical, anomalised data from millions of fellow drivers. Since Smart Route helps you automatically avoid predicted heavy congestion, you will be able to save time and money during your journeys.

My Drive

With My Drive technology, your Navman includes an intelligent capability that learns and adapts to your personal driving style. Over time, your Navman learns your preference for road types and driving speeds, turns and more. Your Navman will save the information and provide a more personalised route and accurate time of arrival the next time you plan a trip.

For more information about Smart Route and My Drive settings, refer to the Route Options section in at can I customise?"

Back-On-Track™ Automatic Rerouting

You will be redirected if you make a wrong turn. A message informing you that your route is being re-calculated will display at the top of the screen.

To cancel a route re-calculation, tap

In the Map options screen. A warning will display asking you to the re-calculation and your current route will be cancelled.

confirm the cancellation. If confirmed, both the re-calculation and your current route will be cancelled.

Parking Assistant

Parking Assistant is not available on all models.

You will be reminded of the parking information when you are arriving at the destination (within 1 km) of the route. Simply tap the icon on the Map screen to show the nearby parking lots that are sorted by distance.

Destination M79/ Calder Fwy 260 m 100 M79 (Calder Fwy)

Select POI © Jetport Self Park Tullamarine, Melbourne, VIC 380 m © Car Park Elstone Ct, Niddrie, Melbourne... 1.6 km © Car Park Carrington Rd, Niddrie, Melb... 2.2 km © Australia National Car Park Furlong Rd, St Albans, Melbo... 2.5 km

How do I create a trip with multiple stops?

Trip Planner lets you set multiple stops or waypoints for your trip. Your route will be calculated to go via each of these points in the specified order.

1. On the Main Menu, tap

The TRIP PLANNER screen will display.

1. Tap Create New Trip. The Edit screen will display.

TRIP PLANNER Create New Trip

New Trip 1 My Current Location Add Edit GO

1. Tap Add. The Add as waypoint screen will display. Use the FIND address wizard, Explore map, My Places/Recent Locations menu or Here/Return to start to set the waypoint.

2. When your search is done, tap

The waypoint is added and the Edit screen will display.

Add as waypoint Trevi Court Hostel 95 Bulla Rd (37) Essendon North, Victoria 3041 Australia +(61)-(3)-93743500 3.0 km / 7 min Explore Call Accept

Trip to Trevi Court Hostel My Current Location Trevi Court Hostel, 95 Bulla Rd (37) Add Edit GO

1. Complete the following:

If you want to ... Then ...
add another waypoint, i Waypoints added after a multi-stop trip has commenced will not be included in the current route.	tap Add.▪ The Add as waypoint screen will display.▪ Return to step 3.
navigate to your selected destination,	tap ↗.▪ The Map screen will display the calculated route.
edit the trip, tap Edit, then you can:	▪ optimise your trip by selecting Optimise.▪ change the trip title by selecting Rename.▪ delete the planned trip by selecting Delete.

The Optimise function does not take all factors into account. Your waypoints might be reordered to reduce your estimated travel distance. Be sure to confirm the trip on the map and make adjustments as appropriate, particularly if your trip returns to the start location.

How do I edit the waypoints in the trip?

1. On the Main Menu, tap 📋. The Trip Planner screen will display.

2. Tap the trip to edit.

3. Tap a waypoint in the trip. The Preview screen will display.

Trip to Shell My Current Location Trevi Court Hostel, 95 Bulla Rd (37) Cafe Chezzi, 70 Bulla Rd Shell, 249 Keilor Rd Add Edit GO (2) Cafe Chezzi, 70 Bulla Rd Cafe Chezzi 70 Bulla Rd Strathmore, Victoria 3041 Australia +(61)-(3)-99377309 8.5 km / 7 min Explore Call Move

1. Complete the following:

If you want to ... Then ...
delete a waypoint,	tap Delete, then select OK.
change the order of the waypoint,	tap ∧ or . √

How do I skip a waypoint during a multi-stop trip?

1. Tap anywhere on the Map screen to bring up the Map options screen.

2. Tap ☐, then select Yes. The next waypoint will be skipped and the route recalculated to the following waypoint.

You can also add waypoints during the trip by selecting from the Map options screen.

How do I capture a location or a journey?

The capture functionality is not available on all models.

Your Navman has a capture feature which allows you to record GPS co-ordinates of a location or a journey, and then save them so you can navigate back at a later time.

How do I capture the GPS co-ordinates of my location?

1. On the Main Menu, tap 📋. The Capture screen will display.

Location M79 Augustines Way Jackman Cres Hill Ct Cancel Save as Car Save (2)

1. Tap Save, or wait for 5 seconds. You will hear a shutter sound to indicate that the GPS co-ordinates have been saved. The location is saved in My Places.

Tap Save as Car will save the current car location in My Places.

How do I capture a journey?

To enable capturing of journeys, you must first enable Capture Journey from Main Menu → 🙏 → Route options. For more information, refer to the "What can I customise?"

1. At the beginning of the journey you would like to record, tap Clear. All travel that you have made (i) since midnight, (ii) the previous time you tapped Clear, or (iii) last captured a journey, will be deleted.

2. Travel on your journey. Your Navman will keep a record of where you travel.

3. At the end of your journey, tap from the Main Menu. The Capture screen will display.

4. On the Capture screen, tap 📋. The Journey screen will display.

Journey M79 Augustes Way Hill Ct Jackson Creek Cancel Clear Save

1. Tap Save, then Yes. The journey is saved in My Places.

How do I navigate to a location I have captured?

1. On the Main Menu, tap 🤊. The My Places screen will display.
2. Tap the captured destination you want to travel to ( ). The Preview screen will display.
3. Tap . Your Navman will calculate the route from your current location. The Map screen will display.

How do I navigate to the saved car location?

1. On the Main Menu, tap 🤐. The MY PLACES screen will display.
2. Tap Find My Car. The Find My Car screen will display.
3. Tap 📋. Your Navman will calculate the route (in Pedestrian mode) from your current location. The Map screen will display.

How to view a journey I have captured?

1. On the Main Menu, tap 🤐. The My Places screen will display.
2. Tap the captured journey you want to view ( ).

My Places has all your saved locations.

How do I save a location as My Place or Home?

1. Search for an address until the Preview screen is displayed.

Destination 5 Elizabeth Ave Mascot, New South Wales 2020 Australia 9.0 km / 7 min Explore Save GO

1. Tap 🤊+ The Save screen will display. The location has been added to My Places.
2. To save the location as Home, tap . The location has been set as Home.

5, Elizabeth Ave, Mascot, Sydney,... 5 Elizabeth Ave Mascot, New South Wales 2020 Australia Edit 9.0 km / 7 min Explore GO

5, Elizabeth Ave, Mascot, Sydney,... 5 Elizabeth Ave Mascot, New South Wales 2020 Australia Save as Home Rename Delete

How do I navigate to a location I have saved?

1. On the Main Menu, tap 🤊. The My Places screen will display.

MY PLACES NavPix Home 08:49 am Find My Car 8, Alice Hancox Cl, Castle Hill,... 12:09 289 Victoria Rd (40), Gladesvil... 09:00

Tap the Sort by button on the top of the scrolling buttons to change the sorting order of the items:

: by time

: by name

: by type

1. Tap the favourite destination you want to travel to. The Preview screen will display.
2. Tap Your Navman will calculate the route from your current location. The Map screen will display.

How do I navigate to Home?

If you have not set an address as Home, the first time you try to navigate to Home you will be prompted to search for an address using the address-entry wizard.

1. On the Main Menu, tap 🤊. The My Places screen will display.
2. Tap . The Preview screen will display.
3. Tap 📋. Your Navman will calculate the route from your current location. The Map screen will display.

You can simply tap on the Main Menu and you will be directed to Home quickly once your home has been set on your Navman,

How do I navigate to a recent place?

To make navigating to an address easier, your Navman will automatically save all your start locations and destinations in a list of recent places.

1. On the Main Menu, tap 🤊. The My Places screen will display.
2. Tap The Recent Locations screen will display.

Recent Locations Cowell St Car Park 12:09 289 Victoria Rd (40), Gladesvil... 10:08 Parking Lot 09:08 Carisbrook Historic House & M... 19/04/12 410 Victoria Rd (40), Gladesvil... 18/04/12 Mt Alexander Rd, Essendon, V... 11/04/12

1. Tap a recent place. The Preview screen will display.
2. Tap Your Navman will calculate the route from your current location. The Map screen will display.

How do I edit a saved location in My Places?

1. On the Main Menu, tap 🤊. The My Places screen will display.
2. Select a location to edit. The Preview screen will display.
3. Tap ♥. The Edit screen will display.
4. Complete the following:

If you want to ... Then ...
save the location as Home,	tap [IMAGE].
rename the location,	tap [IMAGE].▪ The Keyboard screen will display.▪ After you have edited the name, tap OK.
delete the location,	tap [IMAGE].

How do I navigate to a NavPix™?

NavPix™ is not available on all models and is only available in selected countries.

NavPix™ is an image or picture, normally of a location, which contains embedded GPS co-ordinates that you can navigate to.

To navigate to a NavPix™ location, either a GPS fix must have been available when the NavPix™ was taken, or GPS co-ordinates have been added using NavDesk.

How do I navigate to a NavPix™ in an album?

For more information about importing the NavPix™ to your Navman, refer to the Photo Album section. What is the NavDesk?"

1. On the Main Menu, tap

The My Places screen will display.

1. Tap NavPix.

MY PLACES NavPix Home 08:49 am Find My Car 8, Alice Hancox Cl, Castle Hill,... 12:09 289 Victoria Rd (40), Gladesvil... 09:00

1. From the list select the album ( ) you want. The album contains your pictures and displays them as thumbnails.

NavPix airport (1) 15/05/12 opera house (2) 13/05/12 opera house Sydney Op... Sydney Op... Slide Show ① ② ③ ④ ⑤

Item Description
1		Tap to return to the previous screen.
2	Album title Display	the title of the album.
3		Indicates that the picture is a NavPixTM, with embedded GPS co-ordinates.
4	NavPixTM thumbnail	A thumbnail of a NavPixTM contained in the album.▪ To select a NavPixTM, tap the thumbnail.
5	Slide Show Displays	all images in the album as a full-screen slideshow.

1. Tap the thumbnail of the NavPix™. The NavPix™ will appear in full-screen.

Sydney Opera House ① ② ③ ④ ⑤

	Item Description
1		Tap to return to the previous screen.
2		Tap to display the previous/next NavPixTM.
3		Tap to start/stop slideshow.
4		Tap to display the Navpix Details screen.
5		Tap to calculate the route, open the Map screen and start navigating.

How do I edit the NavPix™?

1. From the Album screen, tap the thumbnail of the NavPix™. The NavPix™ will appear in full-screen.

2. Tap i. The NavPix Details screen will display.

Sydney Opera House Sydney, New South Wales 2000 Australia 12.6 km / 17 min Explore Edit GO

1. Complete the following:

If you want to ... Then ...
calculate the route and start navigating,	tap ↻.▪ The Map screen will display.
edit the NavPixTM,	tap ♥.▪ To save the location as Home, tap △+.▪ To rename the title of the NavPixTM, tap ♥I.▪ To delete the NavPixTM, tap ♥x.
explore the map,	tap 🔍.

How do I search for a POI?

A POI (Point of Interest) is a named site, feature, landmark or public venue which can be displayed as an icon on the map. POIs are grouped by category, such as petrol stations, parks, beaches and museums.

Your Navman provides several ways to search for the nearby POIs:

EXPLORE
■ the POI category buttons on the Main Menu
■ FIND wizard

How do I find the nearest POIs using EXPLORE?

The Explore map allows you to explore the local area to find Points of Interest (POIs) or navigate to an address. If you do not have a GPS fix, the map will display your last known position.

1. On the Main Menu, tap

The Explore screen will display.

1. On the Explore map, you can:

■ View the information of the selected POI that is shown at the top of the screen.
- Tap and drag the map to explore your desired local area.
- Tap the map to display a POI Cluster showing POIs in the surrounding area. Tap a POI icon to show more information and navigate to the POI.

Calder Fwy (40), Keilor, Victoria 3036, Australia Old calder Hwy Eagling St Harbin St Alkai St Kappady St Flora St Milburn Rd Hunter St Church St Ram + - 6

	Item Description
1		Tap to return to the previous screen.
2	Information area Display the information of the selected POI/position.
3	ent position	Your current position is marked with [IMAGE].
4	POI Cluster To display a POI Cluster, tap an area on the Explore map.	Tap an icon or street name in the POI Cluster to view information and options.
5		Tap to display the POI Display screen, allowing you to set POI preferences.
6	/	To zoom in or out, tap and hold + or - Zooming in or out will increaseor decrease the area contained within the Explore area.

How do I find a POI using the POI Cluster?

1. Tapping on the POI selected will bring up the screen with the POI destination details.

1. Complete the following:

If you want to ... Then ...
calculate the route and start navigating,	tap ▪ The Map screen will display.
save the location as a favourite,	tap [AY8]▪ The location will be saved in My Places immediately.
explore the map,	tap
place a phone call to the POI,	tap iThis feature is not available on all models.

How do I set my POI preferences?

Points of Interest (POIs) are grouped into categories. You may choose to either display (or hide) icons of all POI categories on the Map screen, or only display the icons from selected categories.

For example, you may only be interested in entertainment venues and want to disable other categories such as schools.

1. Tap 📋. The POI Display screen will display.

POI Display Accident Black Spot Airport Amusement Park Art Gallery Arts Centre Show all Hide all

1. Complete the following:

If you want to ... Then ...
display all POI icons (i.e. icons from all categories),	tap Show all.
display no POI icons, tap Hide all.	Hiding POIs will stop you from finding them when using explore mode/cluster search.
select a specific POI category icon for display on the Map screen,	▪ tap required POI category to show ( ) or hide ( ) on the Map screen.▪ repeat until all required categories are selected.
return to the Explore map,	tap [IMAGE].

- Your preferences are automatically saved.

How do I find the nearest POIs using the POI category buttons?

The POI category buttons are not available on all models.

1. From the Main Menu, select one of the following:

If you want to ... Then ...
search for the nearest petrol stations	tap
search for the nearest emergency service	tap
search for the nearest restaurants	tap
search for the nearest hotels/motels	tap
search for the nearest parking places	tap
search for the nearest banks and ATMs	tap

1. A list of the selected POI category based upon your current location is displayed.

2. Select the desired item to display the destination screen.

3. Complete the following:

If you want to ... Then ...
calculate the route and start navigating,	tap ▪ The Map screen will display.
save the location as a favourite,	tap ▪ The location will be saved in My Places immediately.
explore the map,	tap
place a phone call to the POI,	tap ⓘ This feature is not available on all models.

How do I search for a POI by type?

1. On the Main Menu, tap

1. Tap i. The Find a POI screen will display.

Find a POI Nearby In City/Area Along Route Near Destination

1. Complete the following:

If you want to ... Then ...
search for the POIs near your current location,	tap .
search for the POIs in a specified city or area,	tap ▪ The Keyboard screen will display.▪ After you have entered a name of a city/area, tap OK.
search for the POIs on your route,	tap
search for the POIs near your destination,	tap .

1. The POI Type Selection screen will display. Complete the following:

If you want to ... Then ...
search for POIs by keyword,	tap ▪ The Keyboard screen will display.▪ After you have entered a keyword, tap OK.
search for restaurants, cafes, fast-food premises and other dining establishments,	tap [XCVA]
search for petrol stations,	tap
search for parking places,	tap
view more POI types,	tap ▪ The POI Type List screen will display.▪ Se
search for hotels and motels,	tap
search for banks and ATMs,	tap [SWC5]
search for emergency services,	tap [0C3K]

1. The POI List screen will display. Tap the desired item from the list.

2. Complete the following:

If you want to ... Then ...
calculate the route and start navigating,	tap .▪ The Map screen will display.
save the location as a favourite,	tap +.▪ The location will be saved in My Places immediately.
explore the map,	tap
place a phone call to the POI,	tap [O86C]iThis feature is not available on all models.

How do I search for a POI by Smart Find Keyword?

Complete the following to navigate to a POI or the street address that you find by keyword.

1. On the Main Menu, tap

1. Tap . Enter the keyword of the POI or Street Address that you want to search.

Example 1: searching for a POI (Inn) by keyword

FIND Smart Find Keyword Address City/Area Coordinates Postcode Intersection Points of Interest Recent Locations

q w e r t y u i o p a s d f g h j k l z x c v b n m 123 OK

Select Result Inn Ct, Gladstone Park, Melbourne, VIC Keilor Motor Inn Old Calder Hwy, Keilor, Melbourne, VIC Tulla Park Inn Take Away Tullamarine Park Rd, Tullamarine, Melb... Holiday Inn-Melbourne Int'l Centre Rd, Melbourne Airport, Melbourne...

→
→

Hotel or Motel Keilor Motor Inn 765 Old Calder Hwy Keilor, Victoria 3036 Australia +(61)-(3)-93363011 2.2 km / 3 min Explore Call GO

Example 2: searching for the street address (Elizabeth street) by keyword

FIND Smart Find Keyword Address City/Area Coordinates Postcode Intersection Points of Interest Recent Locations

→

Elizabeth q w e r t y u i o p a s d f g h j k l z x c v b n m 123 OK

Select Result Elizabeth St, Moonee Ponds, Melbourne, VIC Elizabeth St, St Albans, Melbourne, VIC Elizabeth St, Westmeadows, Melbourne, VIC Elizabeth St, Braybrook, Melbourne, VIC Elizabeth St, Fawkner, Melbourne, VIC Elizabeth St, Kensington, Melbourne, VIC + Elizabeth Lazarkov

→

Destination Elizabeth St Westmeadows, Victoria 3049 Australia 10.4 km / 13 min Explore Save GO

1. Complete the following:

If you want to ... Then ...
calculate the route and start navigating,	tap ▪ The Map screen will display.
save the location as a favourite,	tap ▪ The location will be saved in My Places immediately.
explore the map,	tap
place a phone call to the POI,	tap feature is not available on all models.

How do I receive current traffic information via TMC?

Your Navman can receive current traffic information for all main roads, motorways and major cities, enabling you to avoid potential delays on your route. Event messages and traffic icons will display as they occur. If an event message obscures your current location, the map will adjust to display both the message and your location.

How does my Navman receive traffic information?

Depending on your Navman model, you may receive current traffic information on your Navman using the built-in TMC receiver or via the Navman traffic accessory kit (may be sold separately).

The Traffic Message Channel (TMC) broadcasts real-time traffic information via the FM Radio Data System (RDS). FM radio stations transmit TMC data on a cycle of several minutes, with hundreds of events able to be broadcast to TMC receivers.

You have to pay for TMC service in other countries.

How will I know when a Traffic Event occurs?

When travelling through an area in which you can receive traffic updates, your Navman will decode these events and display them on-screen. An icon will display at the event location on the Map screen, and an audible warning is given if an event is on your route. Where an event spans a specific distance, the road will be highlighted and arrows will indicate the direction affected.

Exit left 37 (Airports) 2.8 km 15.6 DTG km New traffic events received Mount Alexander Road—Southbound Maribyrnong Road > Kent Street traffic congestion, average speed of 20 km/h

A message will display at the bottom of the screen with the road name, the section of road affected and the type of event that has occurred. The message remains on screen for 8 seconds and is added to the All traffic events.

When the message is suppressed, the TMC icon ( ) will be displayed on the Map screen. You can tap the icon to bring up the All traffic events screen.

Traffic overview screen

When you see the traffic event message on your driving Map screen, you can open the Traffic screen to display a general overview of the traffic situation on your route, including all events in the immediate vicinity.

Depending on your Navman model, traffic information may not be available, may require a subscription, or require the Traffic Accessory Kit (may be sold separately).

On the Main Menu, tap

Traffic M79 C754 41 M80 39 43 M8 8 ① ② ③ ④ ⑤

	Item Description
[0CCX]		Tap to return to the previous screen.
	Current position	Your current position is marked with
	Event icon Displays icon to indicate type of event.
[K8ST]	Title bar tabs	Tap to change the display between the Traffic, All traffic events, and Traffic Options windows.
	/	To zoom in or out, tap and hold or

How do I view a list of all events on my route?

Your Navman creates a list of events as they are received, which is displayed on the All traffic events screen.

On the Traffic screen, tap

All traffic events Main Road—Eastbound traffic congestion, average speed of 10 km/h Milleara Road—Southbound traffic congestion, average speed of 20 km/h Western Highway—Eastbound traffic congestion, average speed of 20

	Item Description
1		Tap to return to the previous screen.
2	Event icon Displays an icon to indicate type of event.
3	Event description Displays details of the Event, including:Name of road and direction in which Event is taking place.Location of where Event begins and ends.> indicates an Event from a location, to a location.< > indicates an Event between locations.Type of Event.
4	Sort by Tap to change the sorting order of the items:↓ : by distance ↓ : by road name

How do I view traffic details?

On the All traffic events screen, tap the event you want to view. The Event Details screen will display.

Event details 5.8 km ahead Milleara Road—Southbound From: Keilor Park Drive To: The Crossway traffic congestion, average speed of 20 km/h (Re-route recommended) Explore Detour +1.0 km Avoid

	Item Description
1		Tap to return to the previous screen.
2	Event icon and description	Displays details of the Event, including:Name of road and direction in which Event is taking place.Location of where Event begins and ends.> indicates an Event from a location, to a location.< > indicates an Event between locations.Type of Event.
3	Detour information Displays the information of detour recommendation, if any.Tap to explore the recommended route on the map.
4	Avoid Tap to initiate a new route to avoid the event. Only available if a detour or re-route is available.The Unavoid button is displayed when a re-route has been calculated.

How do I know if a detour is recommended?

When a Traffic or Clearance event occurs on your route, a detour will often be recommended. The detour event message will display in the status bar on Map screen.

Detours are only recommended for Traffic or Clearance Events on a calculated route.

How do I avoid an event on my route?

1. On the All traffic events screen, tap the event. The Event Details screen will display.
2. If a detour has been calculated to avoid an event on your route, Avoid is available; tap to accept the new route and avoid the event. The Map screen will display.

Traffic messages

The Event Details screen displays detour status information.

Detour Not Available messages

If a detour is not available, one of the following messages will display:

Message Description
This Event is not locatableThis clearance is not locatable	A specific location for the Event cannot be identified.
This Event does not affect your routeThis clearance does not affect your route	The Event is not on the current leg of your journey, or is behind your current position.
You are avoiding this EventYou have accepted this clearance	The Event is not on the current leg of your journey.
You are too distant to re-routeYou are too distant to accept this clearance	The Event is currently too distant to affect your journey.
Detour not foundClearance route not found	A detour / re-route could not be calculated.

Detour recommended messages

If a detour is recommended, one of the following messages will display:

Message Description
Finding detour ...Recalculating route ...	Your Navman is calculating a new route. During calculation, the % complete will display.Exiting this screen before the new route is calculated will cancel the operation.
Detour distance ...Clearance change	A detour has been calculated. The difference between the distance of your current route and the proposed route is displayed.

Traffic preferences

You can view your current traffic system status and change options by customising the traffic preferences.

Traffic Options Traffic Service Auto ▶ Accept recommended detours Traffic notifications Only events on my route

TMC Service

1. On the Traffic Options screen, tap Traffic Service. The Traffic Service screen will display.

The TMC service screen displays the frequency of the radio station currently used to receive traffic event information. A bar shows the strength of the traffic signal being received; the more green bars the stronger the signal.

1. To change your preferred radio station, select your preferred radio station from the list. You can select Automatic to receive the traffic signal automatically.

Accept recommended detours automatically

When the Accept recommended detours is selected, your route will be re-planned automatically when the detour is recommended by the traffic event.

Traffic event notification

1. On the Traffic Options screen, tap Traffic notifications. The Traffic notifications screen will display.

2. Complete the following:

If you want to ... Then ...
view all traffic events nearby,	select All events nearby.
view the traffic events on your route,	select Only events on my route.
view the traffic events with detour information provided,	select Only if a detour is recommended.
reject the traffic signal,	select Turn off notifications.

TRAVEL BOOK is not available on all models and is only available in selected countries.

Travel Book is a collection of city guides that provide detailed Points of Interest maps for major cities in local region. The city guides provide information on accommodation, dining, night life, business essentials, shopping, important tourist spots and practical information such as banks, medical centres, bus stations, etc.

Travel Book is provided by third party. Navman does not guarantee the accuracy of the data contained in this database either expressed or implied.

How do I search for a POI in a city I am visiting using travel guides?

1. On the Main Menu, tap the travel book you want to browse:
2. The TRAVEL GUIDES screen will display. Follow the prompts to select your city and POI category.
3. Enter the keyword to search a POI. When done, tap OK.
4. Select a POI from the list. The POI details screen will display.

1. Complete the following:

If you want to ... Then ...
calculate the route and start navigating,	tap [GS38]▪ The Map screen will display.
save the location as a favourite,	tap ▪ The location will be saved in My Places immediately.
explore the map,	tap
place a phone call to the POI,	tap iThis feature is not available on all models.

How do I play videos on my Navman via AV IN?

Depending on your Navman model, you can turn your Navman into an external screen to display video playback from an external composite video source. This feature is suitable for rear reversing camera as well as portable DVD player (sold separately).

The AV IN function supports NTSC/PAL (interlace) formats.

1. Before you use the AV IN function, connect your Navman to an AV external source according to the instructions in the Hardware User Manual.

2. On the Main Menu, tap 📋. The AV screen will display.

3. You can now start playing back the video. The playback screen will appear on your Navman.

4. To exit the playback, tap

How do I make a hands-free call?

Hands-free calling is not available on all models.

If you have a compatible mobile phone with Bluetooth wireless technology, you can use your Navman as a hands-free car kit or to provide an internet connection. It can also be used to connect to a Bluetooth mono/stereo earphone to output audio. Models with Bluetooth capabilities can exchange information over a distance of about 10 metres (30 feet) without requiring a physical connection.

Before you can use this feature you must pair your mobile phone with your Navman. Ensure that the Bluetooth wireless feature of your mobile phone is turned on before you begin pairing. When you search for or connect to a mobile phone/ headset, the Bluetooth on your Navman will be turned on automatically. To save power, Bluetooth is set to OFF by default.

A list of compatible mobile phones is listed at www.navman.com.au (Australia) or www.navman.co.nz

(New Zealand).

How do I pair my Navman with a Bluetooth device?

When you pair the Bluetooth device with your Navman, a connection is established between them. The 12 most recently paired devices will be displayed on the My Paired Devices screen.

1. On the Main Menu, tap

→ Bluetooth. The Bluetooth screen will display.

1. Tap ☐. The Search New Devices screen will display a list of nearby Bluetooth devices.

Bluetooth My Paired Devices Search New Devices Settings To connect to a device, please tap the "Search New Devices" button and make sure the Bluetooth of the device you want to connect to is on.

1. Select the device from the list. The Connecting screen will display.

2. Complete the following:

If you want to ... Then ...
pair with a mobile phone,	enter 1234 on the mobile phone when prompted.
pair with a headset,	on the Enter Passcode screen, enter the passcode and tap OK.

1. When done, the Bluetooth screen will display.

Paired device detail screen

1. On the Bluetooth screen, tap 📋. The My Paired Devices screen will display.

2. The Bluetooth icon next to the paired device indicates the connection status:

icon Status Used for...
	Connected	headset
	Connection with hands-free enabled phone
	Connection with dial-up networking enabled phone

How do I configure Internet settings?

Once the Internet connection is turned on, you are able to access live information over the internet.

1. Tap the paired device from the My Paired Devices screen, then tap

My Paired Devices 5300 Device Details 5300 Status: Hands free Settings delete Disconnect

1. Tap Internet Settings. The Internet settings screen will display.

2. Complete the following:

If you want to ... Then ...
configure the Internet settings by mobile phone's setting,	tap Automatic (copy from phone).
change the operator for your region,	tap By Operator, then you can:▪ tap Country/Region to change your country/region. The Select a country screen will display. Select your country from the list.▪ tap Operator to change the operator for your region. The Select an operator screen will display. Select your operator from the list.
enter your internet settings,	tap User Defined and define your User Name, Password, Dial Number, and Access Point Name.

When internet settings are not available, a warning message will be displayed. For more information, contact your mobile phone service provider.

How do I make a phone call?

The hands-free feature on your Navman can be turned ON or OFF. When turned ON, the following features can be used:

■ Display caller's number
■ Download phonebook
■ Answer or ignore incoming call
■ Dial a number through the Dial, Favorites, Contacts, and Call History screens

1. On the Main Menu, tap

The Phone screen will display.

PHONE Favorites Contacts Call History Dial

1. From the Phone screen, tap 📄. The Dial screen will display.

2. Enter the number you want to call.

■ To delete the last digit entered, tap

■ To clear the entire number, tap and hold

The number of the last call will display when you next access the Dial screen. The number will be cleared as you start entering a new number.

International calls require a country code to be included in the phone number. On your Navman, the country code is separated from the rest of the number sequence by a + sign. If you are making an national call, tap and hold 0 until the + sign displays.

1. Tap Call to place the call. The Dialling screen will display.

2. Complete the following:

If you want to ... Then ...
adjust the volume, tap to increase or decrease the volume.
end or cancel the call, tap Hang up.

How do I receive a phone call?

1. When you receive a call, the Incoming call screen will display.

2. Complete the following:

If you want to ... Then ...
answer the call, tap Answer.	If you want to answer the call using your mobile phone, tap Voice to Phone.
reject the call, tap Ignore.

If your Navman supports Voice Command function, you can receive or reject the incoming call by simply saying "Answer" or "Ignore".

In-call options

1. When a call is in progress, the in-call screen will display as below:

0902005890 02:05 Hang Up Voice to Phone

1. Complete the following:

If you want to ... Then ...
display the Main Menu,	tap [IMAGE].
display the keypad screen,	tap [IMAGE].
switch off the microphone so the receiving party cannot hear you,	▪ tap [IMAGE] to mute.▪ tap [IMAGE] to unmute.
transfer the call to your phone,	tap Voice to Phone.
end the call, tap Hang Up.
adjust the volume, tap to increase or decrease the volume. ⓘ The phone volume adjustment does not change the device volume.

How do I make a phone call to a contact?

1. From the Phone screen tap 📋. The Contacts screen will display.

2. Select a contact from the list. The Contact Detail screen will display.

3. Tap . The Select Number screen will display.

4. Complete the following:

If you want to ... Then ...
call the contact on their mobile phone, home number, work number, or any other number,	tap [IMAGE] next to the number you want to call.
add the number to your Favorites,	tap [IMAGE] next to the desired number.

How do I view my call history?

From the Call History screen you can view a list of Incoming Calls, Outgoing Calls and Missed Calls.

The Call History screen lists the calls made during the time your Navman is connected to a mobile phone. Numbers are arranged by time with the most recent time at the top. Your Navman can store up to 30 numbers; limited to 10 entries for incoming, outgoing and missed calls each.

1. From the Phone screen tap . The Call History screen will display.

2. Tap an item in the list. The Call Record screen will display.

3. Complete the following:

If you want to ... Then ...
delete the call from history,	tap .
place a call,	tap .

To delete all calls in call history, tap

from the Call History screen.

What is NAVMAN CONNECT?

NAVMAN CONNECT is only available in selected countries.

NAVMAN CONNECT allows you to search online for live POI information and receive weather updates for up to five cities. Using Connect you can search for and navigate to POIs using your Navman or you can navigate to POIs you have downloaded using NavDesk.

To search for POIs and to receive updated weather information using your Navman, you must pair your Navman with your mobile phone. If your Navman isn't paired with your mobile phone, the Bluetooth screen will display. For more instructions, refer to the "How do I pair my Navman with a Bluetooth device?" section.

Additional data charges may apply. All charges are billed by your service provider. Please check with your ice provider for more information.

How do I search for a POI using Google Local Search?

1. On the Main Menu, tap LOCAL SEARCH. The Google Local Search screen will display.

Google Find: (tap to enter keyword) Near: Last Position 385 George St, Sydney, New S... Powered by Google Search

1. Complete the following:

If you want to ... Then ...
search for POI information by keyword,	tap the Find field to enter keyword.▪ The Keyboard screen will display. Use the Keyboard screen to search for a POI, then tap OK.
search for POI information near your current location,	tap the Near field to:▪ Select My Places to search for a POI information near a My Place location.▪ Select Find a Place to search for POI information in a new location.▪ Select Recent Places to search for POI information near a recent location.▪ Select Pick on Map to search for POI information around a particular area.

1. Tap Search. The Select Result screen will display. From the result list, tap a POI to display the Preview screen.

2. Complete the following:

If you want to ... Then ...
calculate the route and start navigating,	tap ▪ The Map screen will display.
save the location as a favourite,	tap ▪ The location will be saved in My Places immediately.
explore the map,	tap
place a phone call to the POI,	tap iThis feature is not available on all models.

How do I search for a POI using TrueLocal.com.au?

1. On the Main Menu, tap ✦ → Local Search. The Local Search screen will display.

2. Complete the following:

If you want to ... Then ...
search for POI information by keyword,	tap the Find field to enter keyword.▪ The Keyboard screen will display. Use the Keyboard screen to search for a POI, then tap OK.
search for POI information near your current location,	tap the Near field to:▪ Select My Places to search for a POI information near a My Place location.▪ Select Find a Place to search for POI information in a new location.▪ Select Recent Places to search for POI information near a recent location.▪ Select Pick on Map to search for POI information around a particular area.

1. Tap Search. The Select Result screen will display. From the result list, tap a POI to display the Preview screen.

2. Complete the following:

If you want to ... Then ...
calculate the route and start navigating,	tap [IMAGE].▪ The Map screen will display.
save the location as a favourite,	tap [IMAGE].▪ The location will be saved in My Places immediately.
explore the map,	tap [IMAGE].
place a phone call to the POI,	tap [IMAGE].[IMAGE]This feature is not available on all models.

How do I receive weather information using NAVMAN CONNECT?

1. On the Main Menu, tap ✦ → Weather.
2. Tap Add City, then follow the prompts to select your region, country, and city. When done, the selected city is added to the list.

Weather Powered by AccuWeather.com Update now Add city °C

Weather Powered by AccuWeather.com Berkeley 11°C Last Update : 02:49 ,Today Update now Add city °C

How do I view weather information for a city I have added?

1. On the Weather screen, tap Update now. The latest weather information will be updated automatically.
2. Tap the city to view current weather information. The Weather Information screen for the selected city will display.

Berkeley More Feels Like : 14°C Humidity : 87% Visibility : 16 km Dewpoint : 9°C Wind : 360.0 kph Cloud Cover : 0% Air Quality : Good Sun Rise : 6:13 AM Sun Set : 7:47 PM 11°C Delete Powered by AccuWeather.com

1. Depending on the city you have selected, a range of current and forecast weather and temperature information may be displayed. If available, tap More to view the forecast information.

Berkeley Powered by AccuWeather.com Tomorrow 14 ~ 31°C Thursday 13 ~ 27°C Friday 12 ~ 24°C Saturday 12 ~ 23°C Sunday 13 ~ 24°C Monday 13 ~ 25°C

How do I change between Celsius and Fahrenheit for displaying temperature?

On the Weather screen, tap the Unit button to change the temperature unit between Celsius and Fahrenheit. The button icon indicates the current setting:

How do I remove a city I have added?

On the Weather Information screen, tap 📄. The city is removed from the list.

How do I search for roadside assistance?

Roadside Assistance is not available on all models. Additional data charges may apply. All charges are d by your service provider. Please check with your service provider for more information.

1. On the Main Menu, tap

1. Tap Yes to set the home base before using this service.
2. Select your home base from the list.
3. The Assistance Details screen will display.
4. Complete the following:

If you want to ... Then ...
place a phone call to the assistance centre,	tap This feature is not available on all models.
change the region for a new search, tap	Settings.▪ Select your preferred region.

How do I control my Navman using Voice Command?

Voice Command is only available in selected countries.

Voice Command is a tool that allows you to complete a task without touching the screen. Simply say a command and your Navman will be able to:

■ set your destination
■ answer an incoming call

Voice Command requires the respective voice file, English (AUS), installed and used on your Navman. For further instructions on installing your preferred language, refer to the Voice Command section in "What is the NavDesk?"

How do I plan my route using Voice Command?

1. On the Main Menu, tap 📋. The Voice Command screen will display.

When in navigation mode, you can launch Voice Command directly by tapping the 📋 icon on the screen.

1. You can set the destination by saying the following commands after the "beep" sound:

2. Address
   Home

3. Intersection
   ■ My Places
4. Nearby Parking
5. Nearby Food
   ■ Nearby Hotels & Motels
   ■ Nearby SOS
6. Nearby Cash

7. Nearby Petrol
   ■ Nearby (Airport, Library, Zoo...)
   ■ Increase volume
   ■ Decrease volume
   ■ Increase brightness
   ■ Decrease brightness

8. Follow the prompts to finish your route setting.

Example 1: search for the address by saying "Address" → "city name" → "street name" → "house number" → "item number" in the searching result list → "Yes" to confirm destination.

Example 2: directed to your home simply by saying "Home".

Only when your home has been set on your Navman can you be directed Home by Voice Command.

1. When done, say "Yes" and your Navman starts to plan the route.

How do I answer an incoming call using Voice Command?

To use Voice Command to answer an incoming call, the Answer calls by voice option in SETTINGS must be enabled. For more information, refer to the "What can I customise?" section.

1. When you receive a call, the Incoming call screen will display.
2. Say "Answer" to answer the call, or "Ignore" to reject the call.

What can I customise?

Depending on your Navman model, certain setting options may not be available.

There are various customisation options available to enhance your navigation experience.

1. On the Main Menu, tap

The Settings screen will display.

1. Select the option you want to customise from the Settings screen.
2. Once you change the settings and return to the previous screen, your preferences are automatically saved.

Settings screen options and the order of the options may differ, depending on your region, maps installed or model of Navman.

While changing the settings, the checkbox next to the option indicates the setting status:

: on/enabled

: off/disabled

Audio

Audio Volume Touch audio

Complete the following:

If you want to ... Then ...
increase/decrease the volume,	tap + / - .You can simply tap on the Volume bar so that the volume will be set immediately at the position you tapped. The Volume bar indicates the current volume level.
mute/unmute,	tap ▼ .▪ The speaker icon indicates the status: : muted : unmuted
hear which letter you have tapped when you tap the touch screen,	tap Touch audio to turn it on or off.

Screen

Screen Screen mode Day ▶ Day brightness - + Night brightness -

Complete the following:

If you want to ... Then ...
change the displayed screen mode,	tap Screen mode and select:Auto: set to automatically change between Day and Night modes.Day: set the screen to be displayed in Day mode.Night: set the screen to be displayed in Night mode.
change the screen brightness in day /night mode,	tap / on the Day brightness/Night brightness bar.The brightness bar indicates the brightness level.Warning: Your Navman can heat up when the brightness scale is set high, therefore, use lower brightness whenever acceptable.You can simply tap on the brightness bar so that the screen brightness will be set immediately at the position you tapped.

Safety

Safety Driver fatigue alert Speed limit display Speed limit alerts Speed limit + 5 km/h Set manual speed alert 110km/h

Complete the following:

If you want to ... Then ...
Enable/disable the warning message after long-distance driving,	tap Driver fatigue alert to turn it on or off.
enable/disable speed limit alerts, which warn you of the speed limit on any given road,	■ tap Speed limit display to turn it on or off.■ tap Speed limit alerts and select:○ Off: disable the speed limit alert.○ Auto: set the system to alert automatically while your speed is above the limit.○ Speed limit + 5 km/h (Speed limit + 3 mph): set the system to alert while your speed is 5 km/h (3 mph) or more above the limit.○ Speed limit + 10 km/h (Speed limit + 7 mph): set the system to alert while your speed is 10 km/h (7 mph) or more above the limit.
set the speed limit alerts manually,	tap Set manual speed alert to select the speed limit or turn it off.
enable/disable a visual warning if the screen is accessed in a moving vehicle,	tap Warn me not to operate my Navman while driving to turn it on or off.
set how you want to receive the camera and safety alerts,	tap Speed Camera / Mobile Speed Camera / Red Light Camera / Accident Black Spot / School Zone / Railway Crossing / Speed Check to select:▪ No alerts▪ Visual alert▪ Visual & Audible alerts
set how you want to receive the driver alerts,	tap Driver Alert to select:▪ Auto (default): When the driving speed is above 80 km/h, the audio and visual alerts of all driver alert options will be enabled automatically.When the driving speed is below 80 km/h, the audio and visual alerts for overtaking lane and merging lane options will be enabled, but all other driver alerts will have visual alert only.▪ User-defined: Allows you to set all of the driver alerts manually by selecting:○ No alerts○ Visual alert○ Visual & Audible alerts

Route options

Route options Mode: Car ▶ Route type Choose on map ▶ Types of road Advanced routing Custom Avoidance

Complete the following:

If you want to ... Then ...
change the navigation mode*,* for selected models	tap Mode to select Car, Large vehicle, Professional Truck, or Pedestrian. For more information, refer to the “How do I change the navigation mode?” section.
set route type options for your route,	tap Route type to select your route type preference from the list:▪ Fastest – The route that should be the fastest when navigating.▪ Easiest – The simplest route with the least number of turns and favours motorways where appropriate.▪ Economical – The route with least number of stops, turns and urban areas which should save on fuel usage.▪ Shortest – The route with the shortest physical length. i If you do not select the preferred route type, Choose on map is set as default for this option. All of the four route types will be calculated after your search. Then, you have to select one route type on the map to start navigating.
set types of road options for your route,	tap Types of road.▪ The Types of road screen will display.▪ Select your road preference from the list. i Avoiding ferry routes may prevent you from navigating between certain countries, even when a bridge or tunnel exists.
set the routing preference,	tap Advanced routing to turn the Smart Route / My Drive functions on or off.▪ Use historic traffic speed date: enable/disable the Smart Route function.▪ Use learned driver behaviour: enable/disable the My Drive function.▪ Driving speed records: display the information of your driving speed in Motorway / Highway / Major road / Minor road.
set the avoidance manually, tap Custom Avoidance.	Tap Add Avoid Road and then follow the on screen instructions to select the avoid road from the map view screen.▪ Tap Add Avoid Area and then follow the on screen instructions to select the avoid area from the map view screen.Once the avoidance has been set, it will not be added to your route while you are planning the trip. To edit the assigned avoidance, tap the item from the Custom Avoidance screen and then select Enabled/Disabled, Rename, or Delete.
display the installed custom POI,	tap Custom POI alerts.
give spoken navigation by landmark or other descriptive reference,	tap Natural guidance to turn it on or off. i Natural guidance is not available on all models and is only available in selected countries.
display landmarks on your route,	tap Landmark guidance to turn it on or off.
record mileage for your route to generate expense reports,	tap Mileage recorder to turn it on or off.
record your journey,	tap Capture Journey to turn it on or off.

Map display

Map display Auto-zoom map when navigating Show no-entry road signs 3D landmarks Map Junction views 3D Still

Complete the following:

If you want to ... Then ...
enable/disable automatic zooming during navigation,	tap Auto-zoom map when navigating to turn it on or off.▪ If selected, the Map screen will automatically zoom in or out, depending on your speed, to allow optimal viewing of your route.
display North at the top of the 2D Map screen,	tap Keep North at top of 2D Map screen to turn it on or off.▪ If set to Off, the direction you are travelling in will display at the top of the 2D Map screen. This option is available only when the Map option is set as 2D view mode.
display “no entry” icons on “no entry” roads on the Map screen,	tap Show no-entry road signs to turn it on or off.▪ When turned on, the map display performance can slow down due to the number of no entry roads in some major cities.
display 3D landmarks on your route,	tap 3D landmarks to turn it on or off. This feature is not available on all models.
set your Map screen preference,	tap Map to select between a 3D or 2D view of the Map screen.
set how to display the junction views,	tap the Junction views option to select: Off or Still.
change the map colour scheme,	tap Map scheme, then select a colour scheme from the list.

My Maps

My Maps Map version Map set Australia Expiring maps

Complete the following:

If you want to ... Then ...
view the map information,	tap Map Version to display a list of all maps, providing the following information:▪ Name▪ Date▪ Version/Build number▪ Coverage area
select a set of maps to load,	tap Map set, then select your preference from the list.

Language

The available settings of the Language option can be customised by adding/deleting the voice file through NavDesk when your Navman is connected to the computer. For more information, refer to the My Navman section in "What is the NavDesk?"

Language Language English (AUS) Voice Karen

Complete the following:

If you want to ... Then ...
change the on-screen language,	tap Language and select your preferred language from the list.
change the voice scheme,	tap Voice and select your preferred voice scheme from the list.

Answer calls by voice

Answer calls by voice is not available on all models and is only available in selected countries with a patible mobile phone.

Answer calls by voice • On • Off

Complete the following:

If you want to ... Then ...
enable Voice Command function while receiving the incoming call,	tap On.
disable Voice Command function while receiving the incoming call,	tap Off.

Units

Units Distance units Metric - kilometres ▶ Time format 12 hour ▶ Date format dd/mm/yy ▶

Complete the following:

If you want to ... Then ...
change the distance units,	tap Distance Units and then select your preferred distance unit type.
change the time format,	tap Time format and then select your preferred time format.
change the date format,	tap Date Format and then select your preferred date format type.

Time Zone

Time Zone Local time: 09:43 Fri, 11/4/08 • Auto time zone ■ Manual time zone: — GMT +10:00 +

Complete the following:

If you want to ... Then ...
set the time zone automatically, select Auto time zone.
change the time zone manually,	select Manual time zone and then adjust the setting by tapping - / + .

Bluetooth

Bluetooth is not available on all models. The Bluetooth option allows you to pair and select a mobile phone or the headset with your Navman. For compatibility list, please see Website: www.navman.com.au (Australia) or www.navman.co.nz (New Zealand).

Bluetooth My Paired Devices Search New Devices Settings To connect to a device, please tap the "Search New Devices" button and make sure the Bluetooth of the device you want to connect to is on.

Complete the following:

If you want to ... Then ...
enable/disable Bluetooth on your Navman,	tap Settings.▪ Tap Bluetooth to turn enable/disable Bluetooth.▪ Tap Auto Connection to enable/disable auto connection function.
connect to a Bluetooth device,	tap Search New Devices and then select a device from the list.
view details of the paired device,	tap My Paired Devices and then select a device from the list.

Trip Meter

Trip Meter is not available on all models. The Trip Meter option displays the information of your trips.

Trip Meter - Current Trip Distance: 19.0km Average Speed: 34km/h Max Speed: 110km/h Time Travelled: 57min Stationary Time: 24min Reset Trip Meter

: display the current trip

: display all trips

Device

Device Delete saved information Restore factory defaults Reset GPS GPS logging

Complete the following:

If you want to ... Then ...
delete the saved information on your Navman,	tap Delete saved information:Tap Delete My Places and tap Yes when the warning dialog box displays. The data saved in My Places will be deleted.Tap Delete recent locations and tap Yes when the warning dialog box displays. The data of recent locations will be deleted.Tap Delete planned trips and tap Yes when the warning dialog box displays. The planned trips saved on your Navman will be deleted.Tap Delete phone data and tap Yes when the warning dialog box displays. The contacts imported from your phone will be deleted.
restore factory default settings,	tap Restore factory defaults.When the warning dialog box displays, tap Yes. Your Navman will restart.TheRestore factory defaultsoption allows you to restore default factory settings; the recent locations and saved My Places destinations on the device will be deleted.When you restore factory defaults, your My Drive profile will be cleared form the device.
reset the GPS, tap Reset GPS.	When the warning dialog box displays, tap Yes.Occasionally, the GPS fix may need to be reset. This may occur if the receiver has been transported a long distance since last being used; for example, to a different country, and is still trying to establish the previous position.
record a GPS log of your trip,	tap GPS logging to turn it on or off.

Demo

Demo Off Screen Saver Video Australia, New South Wales Australia, Victoria Australia, South Australia

Demo will begin when the device is connected to power via genuine Navman AC Chargers.

Complete the following:

If you want to ... Then ...
enable a shop demonstration of Navman Spirit to be played,	select a demonstration country from the list and tap Start.▪ Tap OK. Your Navman will restart.When your Navman is in Shop demo mode, you will see the navigation demonstration of the pre-defined route without having to set a destination. ⓘ You cannot operate your Navman properly in Shop demo mode.
enable the screen saver feature on your Navman,	tap Screen Saver Video.▪ When your Navman is idle for 10/30/60 minutes, the screen saver will display. ⓘ The screen saver will only display if your Navman is connected to a power supply.

Help

Help View Tutorial About

Complete the following:

If you want to ... Then ...
view the tutorial, tap View Tutorial.	▪ To display the tutorial on each start-up, select the Show tutorial on start-up option on the initial screen of tutorial.
view copyright and trademark information, obtain UUID or hardware ID number,	tap About.

NavDesk is a suite of tools you can use to access greater functionality and product information via your computer.

NavDesk allows you to:

• obtain software updates
  ■ manage maps
  ■ search online for local POIs
  ■ manage custom POIs
  ■ plan trips

■ manage safety camera subscriptions

- browse the Navman website for special offers

Can I use NavDesk with my computer?

Ensure your computer has the following minimum system requirements before installing NavDesk:

■ IBM compatible PC
■ Microsoft Windows XP SP2/SP3, Windows Vista, or Windows 7 (XP MCE, XP x64, Vista x64 not supported)
■ Internet Explorer 6, 7 & 8
■ DVD drive
USB port
- Internet connection for activation.

Microsoft .NET 2.0, 3.0 and 3.5 will be installed on your computer as part of the installation of NavDesk.

How do I install NavDesk onto my computer?

Before you begin, ensure that your computer meets the minimum system requirements for NavDesk, especially:

• Ensure that Internet Explorer 6 or higher is installed on you computer before you install NavDesk, even if it is not your default browser.
  (for Windows XP users) Ensure that Windows XP Service Pack 2 or higher has been applied before you install NavDesk.

CAUTION: When your Navman is turned on and connected to a computer, it is recognised as an external mass-storage device. Do NOT delete any files that are pre-installed on your Navman. Deleting the files can cause your Navman to crash.

1. Close all programs on your computer.

2. Insert the NavDesk Application Installer DVD into your computer DVD drive. The NavDesk installer will start.
   If your computer does not automatically launch the DVD, start the installation manually: Start → Run. Type D:\Install.exe where "D" is the letter assigned to your DVD drive, then click OK.

3. Select your preferred language for NavDesk.

4. Click Install Software, then Install NavDesk.

5. Follow the screen prompts to install NavDesk:

■ Review and accept the Licence Agreement for NavDesk when prompted.
- Select a destination folder for NavDesk when prompted.
- When the installation is complete, click Finish. NavDesk will open.

1. If prompted to connect your Navman to your computer, complete the following:

2. Plug the large end of the USB cable (supplied) directly into a USB port on your computer (not a USB hub) and plug the small end into the USB Socket ( ) on the bottom of your Navman. Where possible, plug the USB cable into a USB port at the back of your computer.
   ■ Turn on your Navman, and then select the Computer option from the pop-up message screen.

How do I get started?

You are now ready to use NavDesk for your Navman. You can access NavDesk via: Start → All Programs → Navman → NavDesk

The NavDesk Menu

Depending on your Navman model, certain NavDesk Menu options may not be available.

Navman Online My Subscriptions My Maps VOICE COMMAND Custom POIs Photo Album Image Search Application Gallery Unlock Features MY PLACES TRIP PLANNER MY NAVMAN CONNECT

Component Description
1	Navman Online	Display the Navman website, Navman Store and other online features.
2	My Subscriptions Information on your current subscriptions, including safety camera subscriptions.
3	My Maps Install and manage maps.
4	VOICE COMMAND Install or remove a voice command file.
5	Custom POIs Application that allows you to import custom POIs.
6	Photo Album	Import and edit NavPixTM images.
7	Image Search	Search online and download NavPixTM which can be added to My Places or Navman.This feature is powered by FlickrTM.
8	Application Gallery	Customise and rearrange applications available on the Main Menu screen of your Navman.
9	Unlock Features	Allow you to enter the activation key for the service you purchased.
10	MY PLACES View and modify all places including addresses, Points of Interest, NavPixTM, and others added using NavDesk and stored on your Navman.
11	TRIP PLANNER	Add or begin a planned trip with multiple waypoints on your computer, and then save the trip to your Navman.
12	MY NAVMAN	A collection of applications that allow you to configure NavDesk, download updates, and transfer data to and from your Navman.
13	CONNECT Search for and add live POIs to My Places.

The First Use Date information

Once your Navman is connected and the system retrieves the device's data from the server, the First Use Date (FUD) information will be displayed in the status bar (at the bottom of the NavDesk window).

MY PLACES TRIP PLANNER First Use Date (FUD): 12/06/2012

My Subscriptions

NavDesk → My Subscriptions

New Online File Help Navman Online My Subscriptions My Maps VOICE COMMAND Custom POIs Photo Album Image Search Application Gallery Unlock Features Redeem MY PLACES TRIP PLANNER Available Subscriptions Travel Books Andorra Australia France Monaco New Zealand My Subscriptions Travel Books Australia AAA Tourism - accommodation - AAA To Australia Canberra, Australian Capital Territory - w France France - Michelin tourism - Via Michelin 201 Refresh view Recover Subscriptions Delete

Your Navman contains pre-loaded subscriptions, such as safety camera and travel book information. For the latest subscription updates, visit www.navman.com.au (Australia) or www.navman.co.nz (New Zealand). Subscription information is not available on all models and is only available in selected countries.

Safety Camera alerts can be set to enable a warning sound or visual warning when on your route.

How do I purchase a subscription?

1. Select a type of subscription. A list of regions will display.
2. Select a region. A list of available subscriptions will display.
3. Select a subscription or offer, then click Purchase an activation key from the Navman store. The Navman Store website will open.
4. Follow the prompts to purchase your subscription.

A product key will be sent to you via email when you have subscribed. You will need to use this product key to activate your subscription.

How do I activate my subscription?

NavDesk → Unlock Features

1. Enter your product key.
2. Follow the prompts to activate your subscription.

How do I update subscriptions on my Navman?

The My Subscriptions section will display a list of subscriptions already installed on your Navman:

Icon Description
Red	Expired subscriptions.▪ Right click to purchase a new subscription.
Yellow	Available subscriptions.▪ Right click to update and purchase new subscription.
Green	Active subscriptions. No updates are available for these subscriptions.

How do I recover my subscription?

If your subscriptions are deleted and you want to recover them, click Recover Subscriptions at the bottom-right corner in My Subscriptions to recover all subscriptions.

My Maps

My Maps allows you to install new maps, remove maps from your Navman and purchase new maps.

NavDesk → My Maps

NasCell 7.50 File Help Navman Online My Subscriptions My Maps VOICE COMMAND Custom POIs Photo Album Image Search Application Gallery Unlock Features Redeem MY PLACES TREP PLANNER Loadable Maps DVD Drive Open My Navman ( Internal ) 2.55GB Free Remove Maps Total selected 16

Component Description
1	Loadable Maps	A list of maps on the DVD or available for purchase via the Navman Store website. Select a map source (e.g. DVD Drive) and then click Open to display the Map Source section.From the map Source section, click Install Maps to install the selected map to your Navman. Otherwise, click Upwards to return to the Loadable Maps section.
2	My Navman A list of maps installed on your Navman.
3	Remove Maps Click to remove the selected map from your Navman.

How do I install maps onto my Navman?

Your Navman comes with one or more pre-activated maps. Map files take up space on your Navman's internal memory. If you do not use a map file, you can remove it to free up space. You can later reinstall it to your Navman if required.

You can install maps from the following:

■ DVD that came with your Navman.

You may need to purchase a Map Product Key to activate maps on the DVD that came with your Navman.

■ The downloaded map update.

For more information about downloading the free map update, refer to the "How do I update my Navman?" section.

The map that you have purchased separately to a memory card or your Navman internal memory.

Features available in your home country may not be available overseas, e.g. postcode search.

1. Open NavDesk, and then click My Maps.

2. Select a map source (e.g. DVD Drive when a Map DVD has been inserted into your computer DVD drive) and then click Open to display the Map Source section.

■ The maps already installed on your Navman are green.
The maps that are unlocked and ready to be installed to your Navman are yellow.
The maps that require activation before being installed to your Navman are red.
■ The maps that are available for purchase from Navman are blue.

If your computer opens Windows Explorer when the DVD is inserted, close the Windows Explorer low.

1. Complete the following:

If the map to be installed is ... Then ...
yellow go to step 6.
red the map needs to be activated	via the Internet before it can be installed; continue to step 4.

1. If you connect to the Internet via a dial-up connection, connect to the Internet now.

2. Follow the prompts to activate your Map Product Key, including:

3. Enter the Map Product Key when prompted.

4. Your computer will connect to the Internet and activate your Map Product Key.

5. When activation has completed, the map will change colour to yellow; continue to step 6.

6. Click the map you want to install to your Navman. The map will change colour to a brighter yellow to indicate it has been selected. To deselect a map, click the map again.

You may need to install multiple maps to cover the required geographical area.

1. Complete the following:

If you want to ... Then ...
install a yellow map,	go back to step 6.
install a red map,	the map needs to be activated via the Internet before it can be installed; go back to step 4.
install the selected maps to your Navman, continue to step 8.

1. Select the destination media (Navman internal memory) for the selected maps, then click Install Maps. The selected maps will be installed and change colour to green.

2. To use your Navman, disconnect the USB cable. You may need to manually reset your Navman.

WARNING: Do not disconnect the USB cable from the Navman USB Socket until the installed map or maps have changed colour to green.

How do I remove maps from my Navman?

1. Open NavDesk, and then click My Maps.
2. From the My Navman section, select the checkbox next to the map you want to remove.
3. Click Remove Maps to remove the selected maps.
4. Confirm that you want to remove the selected map when prompted. The map is removed from your Navman. You can reinstall these maps at any time via NavDesk.

VOICE COMMAND

Voice Command is not available on all models.

Depending on your Navman model, you will be able to set the destination quickly by using Voice Command. Voice Command is a NavDesk application that allows you to install or remove voice file for the Voice Command function.

NavDesk → VOICE COMMAND

File Help Navman Online My Subscriptions My Maps VOICE COMMAND Custom POIs Photo Album Image Search Application Gallery Unlock Features Redeem MY PLACES TRIP PLANNER Loadable files DVD Open Installed voice command files ( Internal ) 2.55GB F Install selected files Total selected: 0 B Remove selected files Total selected: 0 B

You can download and install free Voice Command updates when available. For more information about downloading the update,s refer to the "How do I update my Navman?" section.

1. Open NavDesk, and then click VOICE COMMAND.

2. Complete the following:

If you want to ... Then ...
install a voice command file,	from the Loadable files section, select a file source (e.g. DVD) and then click Open to display the Available voice command files section.In the Available voice command files section, click Install selected files to install the selected voice command file. Otherwise, click Upwards to return to the Loadable files section.
remove a voice command file,	in the Installed voice command files section, select the voice file you would like to remove.Click Remove selected files.

Custom POIs

The Custom POIs (Points of Interest) application allows you to create or import your own POI files. These are called custom POIs. Unlike preinstalled POIs, custom POIs can be removed from your Navman and can have audio as well as visual alerts associated with them.

NavDesk → Custom POIs

New Date 7:00 File Help Navman Online My Subscriptions My Maps VOICE COMMAND Custom POIs Photo Album Image Search Application Gallery Unlock Features Redeem MY PLACES TRIP PLANNER Add new POIs Source file Browse POI category New category Existing category Add to existing POIs Replace existing POIs Alert Settings Visual alert Audio alert Box file Send file Distance 2000x ADD Add to device Installed POIs

Depending on your Navman model, some Custom POIs features may not be available.

Various POI files are available for download free or by subscription from third-party websites. Ensure that downloaded files are in .csv (Comma Separated Values) format. Navman is not responsible for the content or accuracy of the information or the reliability or availability of these websites. The use of information regarding safety camera locations may be subject to local laws in the country of use. You are responsible for checking that you can use the information in your country or in the country where the information will be used.

To create your POI files, open Microsoft Excel and then enter the POI location details (including Longitude, Latitude, Name, and Description) in separate cells. Always use decimal degrees for coordinates and start a new location from a new line. When done, click File → Save As to save it as a *.csv file. Now you have successfully created a POI CSV file.

How do I install custom Points of Interest?

1. In the Add new POIs section, click Browse to select a source file. The Open dialog box will open.
2. Select the file from your local or network drive, then click Open.
3. From the POI Category section:

If you want to ... Then ...
use an existing custom POI category,	select the Existing category option, then select a type from the drop-down list.
Replace an existing POI,	select the Existing category option and a type from the drop-down list, then select Replace existing POIs. If you want to create a new POI instead, then select Add to existing POIs.
create a new custom POI category,	select the New category option, then type a name for the POI category.

1. Set Alert setting as required:

If you want to ... Then ...
enable a visual warning when a POI of this category is in close proximity,	select the Visual alert checkbox.
select an icon to display on the Map screen for POIs of this category,	click Browse to select the icon file from your local or network drive.When you have located the icon file, select it and click Open.The icon file must be a bitmap (*.png and *.bmp) graphic with a minimum size of 6x6 pixels and a maximum size of 32x32 pixels.If you do not select a custom icon, a default icon will display.
select the distance from a POI of this category at which the visual warning should display or the warning chime should sound,	select the distance from the Distance box.To change the units used to measure distance for this POI category, from the tools menu click on options and from the general option select Use metric units checkbox.
enable a warning sound when a POI of this category is in close proximity,	select the Audio alert checkbox.
select a custom sound alert file to play when a POI of this category is in close proximity,	either select a sound file from the list, orclick Add to select a sound file (.WAV format) from your local or network drive. When you have located the file, select it and click Open.If you do not select a custom sound file, a default sound alert will play.

1. Click Add to device to add the POI to your Navman.

Each file corresponds to a POI category; for example, Hotels.csv will be listed on your Navman as the

Hotels category.

How do I delete a Custom POI file/category from my Navman?

1. In the Installed POIs section, click Delete next to the file name. The file is removed from the list, but is not yet deleted.
2. Accept the warning message. The selected file/category is deleted.

Photo Album

Photo Album is a NavDesk application which allows you to copy, delete or move pictures or albums between the NavPix™ library on your Navman and the NavPix™ library on your computer.

NavDesk → Photo Album

New Desk 7:50 File Help 1 Navman Online My Subscriptions My Maps VOICE COMMAND Custom POIs Photo Album 2 Image Search Application Gallery Unlock Features Redeem MY PLACES TRIP PLANNER Desktop Live album View all NavPix MY NAVMAY 3 Sydney Opera House The Sydney (AMP) Tave... Sydney Opera House 4 Desktop - Live album 0 KeyFix Search 5 Create new album Export New/Fix

Depending on your Navman model, certain Photo Album features may not be available.

Component Description
1	Desktop albums	Displays a list of all albums stored in the NavPixTM library on your computer.▪ Click an album to display its contents in the Album display area.▪ Click View all NavPix to display all pictures stored in the NavPixTM library on your computer.
2	My Navman albums	Displays a list of albums stored on the Navman internal memory and on the memory card if one is inserted.▪ Click an album to display its contents in the Album display area.
3	Selected picture When a thumbnail is selected it displays with a blue border.
4	Album display area Displays thumbnails of pictures in the selected album.
5	Search	Type to search for a NavPixTM by name.
6	Toolbar	When a picture is selected, the icons which can be used will be active.

Toolbar

Vertical toolbar with nine labeled icons representing user profile, image editing, and interaction functions

	Button Description
1	Create new album	Click to create a new album in the NavPixTM library you are viewing.
2	Add to My Places	Click to transfer NavPixTM to My Places.
3	Transfer to your Navman or Transfer to your computer	If you are viewing NavPixTM in the NavPixTM library on your computer, this will display as Transfer to your Navman.Click to transfer the selected NavPixTM to your Navman.If you are viewing NavPixTM in the Navman library this will display as Transfer to your computer.Click to transfer the selected photo(s) to the NavPixTM library on your computer.
4	Import NavPixTM	Imports NavPixTM from your computer to the NavPixTM library on your computer.
5	Export to disk	Click to save NavPixTM to your computer or a network drive.
6	View details	Click to view the selected NavPixTM and edit NavPixTM details, including:NavPixTM namelatitudelongitudedescription
7	Rotate left	Rotates the selected NavPixTM 90° to the left.
8	Rotate right	Rotates the selected NavPixTM 90° to the right.
9	Delete NavPixTM	Click to delete the selected NavPixTM.

How do I transfer pictures from Photo Album to my Navman?

You can transfer pictures from your computer to your Navman. You can import any JPEG (.jpg) into Photo Album, add or edit GPS information, and then copy the picture to your Navman.

1. From the Toolbar section, select Import NavPix. The Open dialog box will display.
2. Select a NavPix™ from a folder on your computer and click Open. Thumbnails of the NavPix™ will display in the Album display area.

You can also drag and drop a NavPix™ from a folder on your computer to an Album on your Desk.

1. Either click and drag the required NavPix™ to an album in the Navman albums section, or click the Transfer to your Navman icon on the toolbar.

If you have transferred a NavPix™ with GPS coordinates you can then navigate to where the picture taken.

How can I view and edit pictures or albums on my computer?

If you want to ... Then ...
rotate a picture to left, select the picture	from the Album display area.Click Rotate left on the toolbar.
rotate a picture to right, select the picture	from the Album display area.Click Rotate Right on the toolbar.
view the picture details, select the picture	from the Album display area.Right-click and select View Details, or click View Details on the toolbar.
edit GPS information, select the picture	from the Album display area.Double click on the picture or click View Details on the toolbar.The following information will display:NameLatitude and LongitudeDescriptionEdit the details you want to modify.Click OK to save the changes.
delete a picture, select the picture from	the Album display area.Right click and select Delete or click Delete on the toolbar.

What else can I do with pictures and albums on my computer?

From the NavPix™ library on your computer, you can:

■ add a picture to another album
■ remove pictures from an album
■ add a NavPix™ to My Places
■ view and edit details of a selected picture
■ upload pictures to Flickr™
- export to disk
■ export pictures to Google Earth™
■ search for pictures
■ view all pictures in the library

If you want to ... Then ...
add a picture to another album,	in the Desktop albums section, select the album containing the NavPixTM you want to include in another album.▪ Select the NavPixTM then drag it to the other album. iThe selected NavPixTM is included in the new album, but is not moved, i.e., one instance of the NavPixTM in the library may be included in multiple albums.
remove a picture from an album,	in the Desktop albums section, select the album containing the NavPixTM you want to remove. Select the NavPixTM, right click and select Remove from album. Click the Delete icon on the toolbar if you want to delete the NavPixTM from all albums.
add a NavPixTM to My Places,	in the Desktop albums section, select the album containing the NavPixTM you want to add to My Places. Select the NavPixTM, right click and select Add to My Places.
view and edit picture details,	select the picture then click the View Details icon on the toolbar. Edit the fields as required.
upload picture to the Flickr website,	in the Desktop albums section, select the album containing the NavPixTM you want to upload to the Flickr website. Select the NavPixTM, right click and select Upload to Flickr. You need a Flickr account to upload NavPixTM. To create a Flickr account visit www.flickr.com
save a picture to your computer, select the picture from the Album display area. Right click and select Export to disk or click Export to disk on the toolbar. Navigate to a folder on your computer where you want to save the NavPixTM.
export to Google EarthTM (only NavPixTM with GPS coordinates can be exported to Google Earth),	in the Desktop albums section, select the album containing the picture you want to export to Google Earth. Select the NavPixTM, right click and select Export to Google Earth. Navigate to a folder on your computer to save the file and then open it in Google Earth. You need to install the Google Earth software on your computer to be able to view the file you have created. You can download Google Earth from earth.google.com
search for other NavPixTM,	right-click on the desired NavPixTM and select Search for NavPix near this.
view all pictures in the library,	click View all NavPix at the bottom of the Desktop album section.

Photo Album preferences

NavDesk → MY NAVMAN → Options → Photo Album

Complete the following:

If you want to ... Then ...
change your NavPixTM location on your computer,	click Change. Select a location for your NavPixTM library. Click Save or OK. The warning message will display and you will be prompted to confirm your action. Your NavPixTM library is moved to the new location.
receive a warning message before deleting an image from your device,	select Warn me when permanently deleting a NavPix from my Navman checkbox.
receive a warning message before deleting an image from your NavPixTM library,	select Warn me when permanently deleting a NavPix from my library checkbox.
create a new folder every time you import new photos,	select the Import photos to a new album checkbox.
view NavPixTM when on a route,	select the Show NavPix on map checkbox.

Image Search

Image Search is a NavDesk application powered by Flickr™ allowing you to download photos and import them to Photo Album. You can then upload the photo to the Flickr website, transfer photos to your Navman, export pictures to Google Earth or search for other NavPix™ near the longitude and latitude of your NavPix™.

NavDesk → Image Search

New Search 700 File Help Navman Online My Subscriptions My Maps VOICE COMMAND Custom POIs Photo Album Image Search Application Gallery Unlock Features Redeem MY PLACES TRIP PLANNER Description Tower Sort by ● Root Intersecting ● Relevance ● Off Only Advanced search All images remain the copyright of their original options. Search Add to My Place Import to New Album Sydney Tower The Sydney (AMP) Tower... Sydney Tower Sydney Tower Sydney Tower ... From & ... Sydney Tower Sydney Tower From Myck... Sydney Tower Tour use of Raticu/Raticr AFI is orderly subject to the agreement between you and Raticu, she the increments set restriction of Raticu, an enforcement or warranty of any kind is provided by us and we declare any and all heredites in connection with or taking from your use of Raticu, even powered by Raticu Search. Find out once about Creative Commons license Back Yaving 1 to 30 of 31 BluePix Next

How do I download NavPix™ from the internet?

1. In the Description field enter a search description for the image you are looking for.
2. Select one of the Sort by options.
3. Click Search. Thumbnails of the NavPix™ will be displayed in the NavPix™ display area.

You can narrow your search by selecting the Advanced search checkbox and then selecting a city from the -down list or by entering latitude and longitude details.

How do I import NavPix™ to My Places?

1. Select a picture or group of pictures you want to add to your My Places.
2. Do one of the following to add the selected image to My Places:

- click the Add to My Places button; or

■ right click on the selected picture and then select Add to My Places from the shortcut menu.

Application Gallery

Application Gallery is a NavDesk application that allows you to add, remove and rearrange applications on the Main Menu screen of your Navman. Application Gallery screen items and the order of the options may differ from the below, depending on your region, maps installed or model of Navman.

NavDesk → Application Gallery

Organize and Reorder Main Menu screen Device Main Menu screen FIND MAP MY PLACES EXPLORE TRAFFIC SETTINGS VOICE COMMAND TRIP PLANNER PHONE ROUTE SIMULATION CAPTURE MODE cityseekr GOOGLE LOCAL SEARCH CONNECT AV New Update Application Gallery Unlock Features Redeem MY PLACES TRIP PLANNER Arr to Device Reset to Default Settings Available Settings

Application Gallery is not available on all models.

How do I rearrange Main Menu applications on my Navman Main Menu?

1. Select any application from the Device Main Menu screen section.
2. Drag the application to the position that you would like it to appear on your Navman.
3. Click Save to Device. The order of the Main Menu screen is saved on your Navman. Click Reset to Default Settings to restore the Main Menu screen to the factory default order.

How do I remove an application from my Navman?

1. Select any application from the Device Main Menu screen section.
2. Drag and drop the application to the Available Settings section.
3. Click Save to Device. The application is removed from the Main Menu screen on your Navman and is no longer accessible.

How do I add an application to my Navman?

1. Select any application from the Available Settings section.
2. Drag and drop the application to the Device Main Menu screen section.
3. Click Save to Device. The application is added to the Main Menu screen on your Navman.

Unlock Features

If you have purchased a map unlock code or subscriptions for your Navman, you have to enter the activation key using the Unlock Features application. The activation key will be sent to you by email, or printed on the inside cover of the box if you purchase the map update DVD. You can click the link on the screen to purchase an activation key online.

NavDesk → Unlock Features

NewBook 2.50 File Help Navman Online My Subscriptions My Maps VOICE COMMAND Custom POIs Photo Album Image Search Application Gallery Unlock Features Redeem MY PLACES TRIP PLANNER New Update If you have purchased a map unlock code, travel books or subscriptions, you will have an activation key that you need to rate here. This key will have been sent to your via email. If you have purchased a map upgrade DVD the activation key can be found on the inside cover of the DVD box. Enter Product Key: Need a Product Key? Let you want to go to our version due to purchase a Product Key Continue

i Make sure you have an active Internet connection for this feature.

My Places

NavDesk → My Places

NewDeal 7.50 File Help MY PLACES Type Name 200404 sydney airpo... Sydney airport closures are B, Alice Hancox CI, Castle Hill, Sydney, NSW Curry Spot Sydney Opera House Sydney Tower The Sydney (AMP) T... The Sydney Tower (AMP Tower) Import Export Delete Denistone East North Ryde Anzac Ave Radajoz Rd Lane Cove North West Ryde Meadowbank Ryde East Ryde Eprey Rd Morrison Rd Betteg Rd Lane Cove West Putney Riverview Rheudes Gladesville Hunters Hill Concord Rd Exeter St Woolwich Breakfast Point Huntleys Point Woolwich Concord West Cabarilla Chiswick Pinerola St Concord Point Rd Rhby St Drummoyne Balmain Nobush Canada Bay Russell Lea Rozelle Oadingham Millers Point Buccord Rd Red Point Ridd Point Balmain Rd Mack St Sydney Potts Strathfield Five Dock Lilyfield Globe Slough Ridge

i Make sure you have an active Internet connection for this feature.

My Places is a NavDesk application that allows you to use Google Maps™ to view all places that you have saved on your Navman. My Places includes saved addresses, captured journeys and sound, Points of Interest,

NavPix™, and other locations. You can select, modify and delete places. You can also add locations from Connect and Image Search to My Places. You can install a maximum of 99 locations on your Navman via My Places.

How do I sort My Place locations?

You can sort My Place locations by type and name:

If you want to ... Then ...
sort My Place locations by type, click Type on the My Places panel.
sort My Place locations by name,	click Name on the My Places panel.

How do I import or export a location?

Complete the following:

If you want to ... Then ...
import a location from the computer to your Navman,	from the My Places panel, click Import.▪ The Open dialog box will open. Locate the file you want to import and then click Open. i The supported file format for importing includes: *.KML and *.KMZ.
export a location from your Navman to the computer,	from the My Places panel, select a location and then click Export.▪ The Save as dialog box will open. Enter a descriptive name for the file and then click Save. i The supported file format for exporting includes: *.KMZ.

You can import/export a location by clicking File → Import (or Export) → My Places from the top of Desk Menu.

How do I edit a location from the map screen?

1. From the My Places panel select the location you want to edit.
2. Click the location icon on the map screen. The location summary pop-up will display.
3. Complete the following:

If you want to ... Then ...
edit the location name, click	the location name.Enter a new name or edit the existing name. The location name is changed in both NavDesk and your Navman.
edit the location notes, click	Edit notes.Enter notes. The location note is changed in both NavDesk and your Navman.
share the location,	clickAn email will open ready to send to your friends. Your friend will receive the email with links to either save the image or to save the location in My Places in NavDesk. If the location is a NavPixTM, your friend will receive the image as an attachment to the email. If the location is a captured journey, your friend will receive the journey as a *.KMZ file attached to the email. Your friend will need to have Google Earth installed on the computer to view the KMZ file. If the location is a captured voice recording, your friend will receive the voice recording as a *.wav file attached to the email.
delete the location,	then click Yes to delete the location.i You can delete all locations in My Places by clicking Delete on the My Places panel.
Export the location,	▪ The Save as dialog box will open. Enter a descriptive name for the file and then click Save.

TRIP PLANNER

In addition to TRIP PLANNER ( ) on your Navman, TRIP PLANNER in NavDesk allows you to pre-plan your trip on the computer.

NavDesk → TRIP PLANNER

NewDesk 7:30 File Help TRIP PLANNER 1 2 Route options Route options Plan route Warpers/Spin routes Save Parrades Pre-Planned Routes Name date Coltex 6/23/2012 Show turn Exit New Update Danistone East North Ryde Brah Rd Danistone West Anzac Ave East Ryde Chatswood Lane Cove North Epicn Rd Artarmon Narembu Ryde West Ryde East Ryde Lane Cove Riverview Longoerville Greenwich Hunters Hill Woolwich Waverton Concord West Breakfast Point Cabarita Chiswick Ivorski St Birchgrove Durin St McMahon Concord Planzell Point Rd Abby St Drummoyne Birchgrove Durin St Mullers Russell Lea Rodd Point Rozette Pineville Rd Darling Rd Darling Hars Strathfield Elva Dock Lilyfield Globe Barwood

TRIP PLANNER is not available on all models.

Component Description
1	Route planner
2	Display area

How do I pre-plan a route by search?

1. From the Route planner panel, set your From point and To point.

You can find a location by:

Keyword

Address

: Postcode

Input your content and click your search results.

to start a search. You may need to select from a category list to narrow

1. Complete the following:

If you want to ... Then ...
add a waypoint, click Add Waypoint.
reset or remove a waypoint,	click × next to the waypoint.
set the route preferences,	click Route option and select:▪ Mode: Select the Driving, Walking, or Large vehicle mode to plan your route.▪ Type of route: Select the Fastest, Shortest, Easiest, or Economical way to plan your route.▪ Avoidance: Avoid Unsurfaced roads, Toll roads, Ferry routes, or Special zone in your route.[wzyr] The Route option settings will only apply to the route you are editing.
arrange the destinations in the most efficient order while two or more waypoints are included in the planned trip,	click Waypoint Optimization.

1. Click Plan Route to calculate your route. The route will be displayed on the map.
2. Click Save this route. The route is saved to the Pre-planned Routes section and your Navman simultaneously.

How do I pre-plan a route using the map?

1. From the map displayed in the Display area, click

1. The cursor will be marked with "Add route". Move the cursor and then click on the map to set the From point.
2. The cursor will be marked with "Click to set destination". You can:

■ Move the cursor and then click on the map to set the waypoint.
■ Move the cursor and then double-click on the map to set the To point.

1. When done, click Save this route. The route is saved to the Pre-planned Routes section and your Navman simultaneously.

How do I edit a route?

1. From the Pre-planned Routes section select a route to edit.
2. Complete the following:

If you want to ... Then ...
rename the route,	click the title of the route in the Name column, then enter a new name and press ENTER. Your changes are automatically saved.
delete a saved route,	click next to the route you want to remove.

MY NAVMAN

NavDesk → MY NAVMAN

Please select the language you want to use Language selection Bunjupok Cebali Cebali Denuk Dentech English (AU) English (UK) English (US) English (OE) E2.4.1.1 K 0 Beti Erpatei Españal (Letao Amerado) Fauyai Bravati Itoaou Latvagu Lietevikai Magyar Noleknds

How do I change the displayed language for NavDesk?

You can change the language for NavDesk.

1. Click Language.
2. Select your preferred language.

How do I install or remove a voice file for my Navman?

My Voices is a NavDesk application that allows you to install or remove voice files on your Navman. Voice files take up space on your Navman's internal memory. If you do not use a voice file, you can remove it to free up space. You can later reinstall it to your Navman if required.

1. Click My Voices.
2. Complete the following:

If you want to ... Then ...
install a voice file,	in the Available voice files section, select the voice file you would like to install.▪ Click Install selected voices. The provided DVD of your Navman is needed while installing the voice file.
remove a voice file,	in the Available voice files section, select the voice file you would like to remove.▪ Click Remove selected voices.

How do I register my Navman and set a PIN?

PIN is a NavDesk application that allows you to set a security PIN on your Navman. The PIN will disable your Navman in the event of theft. To set a PIN, you must first register your Navman on Navman's website.

1. Click PIN.
2. Click Register now and follow the prompts to complete the registration form online.
3. When registration is complete, click I have registered my Navman. The PIN screen displays.
4. In the User Name and Password fields, enter the Username and Password that you entered when registering online.
5. In the PIN field, enter the PIN you want to assign to your Navman. Your PIN must be between four and eight numerical digits.

6. Click OK. The PIN for your Navman has been set. The Enter your PIN screen will now display on your Navman when you turn your Navman on.

7. When you want to change the PIN on your Navman at a later time, enter the User Name and Password to enter the PIN screen. Do one of the following:

Leave the PIN field blank and click OK. The PIN is removed and your Navman will no longer require you to enter a PIN.
In the PIN field, enter a new PIN you want to assign to your Navman. The new PIN for your Navman has been set.

How do I report mileage?

Mileage Reporter is a NavDesk feature that allows you to create expense reports (.csv format) based on the mileage and estimated fuel usage recorded by your Navman. To use the Mileage Reporter function of NavDesk, the Mileage recorder option must be enabled on your Navman. For more information, refer to the Route Options section in "What can I customise?"

MainDesk 750 File Help TRIP PLANNER MY NAVMAN Language My Voices PINS Mileage Reporter Backup and Restore Smart Recovery Device Updates Recover keys Options CONNECT Toneframe Show all Show only From 2000-8-7 To 2000-8-7 Fuel Calculate fuel at Litres per 100 instructions Use Start time End time From To Distance (in Km) Load from your Navman Clear from your Navman Export report

Mileage Reporter is not available on all models.

Component Description
1	Timeframe	Specifies the time for which the mileage report will be created.▪ Select Show All to include all recorded mileage.
2	Report panel Displays your trip log data.
3	Fuel Select to include the amount of fuel (estimate) used for the mileage recorded. If selected, specify the number of miles travelled per gallon, or miles/kilometres travelled per litre.
4	Report data buttons	Import report data from your Navman, clear all report data from your Navman or export data to a report (.csv and .HTML).

To change the Mileage Reporter preferences, click NavDesk → MY NAVMAN → Options → Mileage

Reporter.

How do I backup and restore my Navman?

You can save backups of data from your Navman, and later restore it if required. You are recommended to do backup at least once a month.

1. Click Backup and Restore.

2. Complete the following:

If you want to ... Then ...
backup your Navman, click Create new backup. Select the data you would like to backup. Click OK. The backup will be saved to your computer. The backup will be listed on the Backup & Restore window.
restore a backup to your Navman,	select the backup from the list that you would like to restore. Click Restore, then click OK. The backup will be restored to your Navman.
delete a backup, select the backup from the list that you would like to delete. Click Delete, then click OK. The backup will be deleted.

How do I recover maps and voice files for my Navman?

The Smart Recovery application allows you to recover all data to fix your Navman if a problem occurs during operation, including software, maps, voice files, and subscriptions.

1. Click Smart Recovery.

To use the Smart Recovery application to recover data, make sure you have an active Internet connection and the Installer DVD is inserted into your computer DVD drive.

1. The available data will be displayed in the Maps and Voices fields. Select the desired data and click Recover to recover the data on your Navman.

How do I update my Navman?

Occasionally Navman may offer you free updates, including software applications, maps, voice commands, and more. You can check the available updates via the Device Updates function.

1. If a free update is available and your Navman is connected to your computer, a message will display when you start NavDesk.

From the pop-up message window, click View to display the Device Updates screen that contains the available updates.

You can also open the Device Updates screen by clicking the New Update button at the top-right corner of NavDesk.

In some certain updates, you must upgrade your system to the latest version (including the NavDesk your Navman) before you can use the updates. If the new version is detected, a message will display to you to upgrade the system. When prompted, click Yes to start upgrading the system.

1. Complete the following:

If you want to ... Then ...
download the updates,	select the available update from the list, and then lick Download.▪ You can view the download status from the downloading bar.
stop/pause the download, during the download:▪ click × to stop the download.▪ click || to pause the download; when paused, click ▶ to resume downloading.
change the download folder, click Change Path.

1. When completed, the downloaded file will be saved to the assigned folder.

■ For software update, the *.exe file will be launched automatically to install the update.
- For map/voice command update, the system will display the My Maps/Voice Command screen automatically to install the update.

How do I recover keys on my Navman?

The Recover keys application allows you to fix your Navman if a problem occurs during operation. Click the Recover keys option in the menu and then follow the prompts to complete the process.

Make sure you have an active Internet connection to recover keys.

How do I configure NavDesk?

Depending on your Navman model, certain setting options may not be available.

1. Click Options, and then select the desired setting options to configure.
2. Complete the following:

If you want to ... Then ...
keep NavDesk updated,change the units of measurement that NavDesk uses,	click General, and then select the Auto check for updates checkbox.▪ When you select this option, every time you open NavDesk, the available service packs and bug fixes will be downloaded from the Navman server and applied to your Navman.click General, and then:select or clear the Use metric units checkbox to change between imperial and metric units.select or clear the Use decimal degrees checkbox to change between decimal degrees and latitude/longitude co-ordinates.
change the Mileage Reporter settings,	click Mileage Reporter, and then:select or clear the Warn me when deleting all log files from my Navman checkbox.select Distance per volume or Volume per distance to change the fuel economy style.
change the NavPixTMLibrary location,	click Photo Album, and then click Change.Select a folder for the NavPixTM library. The downloaded NavPixTM is moved to the new location.For more information about configuring your Photo Album, refer to the “Photo Album” section.
change the location of where downloaded updates will be saved,	click My Maps, and then click Change.Select a folder for the updates. The downloaded updates are moved to the new location.

CONNECT

CONNECT is not available on all models.

CONNECT is a NavDesk application that allows you to search and install local POIs information from your computer to your Navman. POI locations will be shown in My Places.

NavDesk → CONNECT

File Help My Maps VOICE COMMAND Custom POIs Photo Album Image Search Application Gallery Unlock Features Redoem MY PLACES TRIP PLANNER MY NAVMAN CONNECT Select Location Please select your location Note: Search results will be shown from the centre of the selected location. Country: Select Continue

Make sure you have an active Internet connection for this feature.

How do I search for a POI using Connect?

Before you begin, ensure your Navman is correctly plugged into your computer: plug the large end of the USB cable directly into a USB port on your computer (not a USB hub); plug the small end into 📋 on the bottom of your Navman.

You can either search for a new location, or search using the last known location on your Navman by completing the following:

1. In the Select Location field, you can :

2. Select a custom location to search. Follow the prompts to select your Country → Region/State → Place name, and then select your preference.
   ■ Use the last known location on your Navman to search if your Navman stores the navigation data.

3. Click Continue. The Available Services page will display.

4. Select your preferred search service. The selected services page will display.

Depending on the country you are navigating, the available search services may vary.

1. Enter your search criteria, then click Search. A list of search results will display. For some countries you are required to accept the terms of use.
2. Click next to the POI you want to install to your Navman. The POI will be added to My Places.

Online support

For 24/7 help and support with Navman products, visit our Technical Support Website: www.navmansupport.com.au (Australia), or www.navmansupport.co.nz (New Zealand).

Navman Customer Support

If you have a faulty product or you would like to speak to a member of our Technical Support team, contact: Australia: 1300 NAVMAN (628626), or visit www.navman.com.au New Zealand: 0800 GONAVM (466286), or visit www.navman.co.nz

Speed Limit

Navman products are designed to be used as an aid to safer driving. Navman does not condone speeding or any other failure to comply with your local traffic laws. It is your responsibility to drive within the posted speed limit at all times and to drive in a careful manner. Navman accepts NO liability whatsoever for you receiving any speeding fines or points on your license through using this device. Navman does not guarantee the accuracy of the data contained within this database either expressed or implied. In the event you receive a fine or any other penalty for speeding or contravention of any traffic law, or are involved in an accident, Navman is not responsible for any damages of any type. In some countries the data information regarding speed limits may conflict with local law and/or regulations. It is your responsibility to make sure that your use of the data is in compliance with local laws and/or regulations. Usage is at your own risk.

Safety Camera POIs

Navman products are designed to be used as an aid to safer driving. You can receive messages to alert you to locations of safety cameras, which will enable you to monitor your speed through these areas. Navman does not warrant that all types and locations of safety camera data are available, as cameras may be removed, relocated or new cameras installed. Navman does not condone speeding or any other failure to comply with your local traffic laws. It is your responsibility to drive within the posted speed limit at all times and to drive in a careful manner. Navman accepts NO liability whatsoever for you receiving any speeding fines or points on your license through using this device. Navman does not guarantee the accuracy of the data contained within this database either expressed or implied. In the event you receive a fine or any other penalty for speeding or contravention of any traffic law, or are involved in an accident, Navman is not responsible for any damages of any type. In some countries the data information regarding safety or speed cameras may conflict with local law and/or regulations. It is your responsibility to make sure that your use of the data is in compliance with local laws and/or regulations. Usage is at your own risk.

Point of Interest categories

Icon Description Icon Description
	Airport		Amusement park
	Art centre		ATM/Cash dispenser
	Bank	[8X7S]	Bar/Pub
	Beach		Breakdown service/Car repair facility
	Bowling centre	[03AB]	Business facility or company
	Business office		Bus station
[SZYC]	Camping ground		Car dealer/Automobile dealer
	Casino		Cemetery
	Church		Cinema
	City hall		City, town or village
	Coffee shop		College/University
	Community centre		Commuter railway station
[ECWD]	Courthouse	[204W]	Dentist
	Doctor		Embassy
	Exhibition centre		Ferry terminal
	Fire Brigade		Golf course
[AT88]	Government office		Grocery store
[4523]	Guest house		Higher education
	Hospital/Polyclinic	[420W]	Hotel
	Ice skating	[AB67]	Important tourist attraction
	Information/Tourist information office		Library
	Marina/Yacht basin		Medical
	Monument	[06C8]	Motorcycle dealer
[KSYG]	Motoring organisation office		Mountain pass
	Museum	[6ABC]	Music centre
	Natural attraction		Nightlife
[WEZZD]	Park and ride		Parking
[DTT4]	Parking garage		Park/Recreation area
	Performance art/Theater		Petrol station
[TW76]	Pharmacy		Place of worship
	Police station		Post office
	Public restroom/Toilet facilities	[0YY8]	Public sport airport
	Railway crossing		Rental car agency
	Rest area		Restaurant
	Road accident black spot		Scenic/Panoramic views
	School		School zone
	Shop		Shopping
	Ski resort/Ski lift station		Speed check
	Sport centre		Sports hall
	Sports complex		Stadium
	Tennis court		Travel agency
	Transport ferry		Veterinarian
	Winery		Zoo

The POI categories and the order may differ, depending on your region, maps installed or model of

Navman.

Branded Points of Interest

Branded Points of Interest are available on some maps. These include well known restaurants, accommodation providers, tourist attractions, Petrol stations, etc. The icon will usually display the company logo.

Point of Interest categories by subscription

Icon Description
	Safety Cameras
	Safety Camera (Mobile)
	Red Light Camera
	Combine Camera

My Places categories

Icon Description
	Home
	Saved locations
	Captured journey (for selected models)

Traffic and other TMC Events

Each TMC Event is sorted in to one of nine categories. When an Event is received, one of the following icons will display:

Event	Avoided Event	Message Type	Event Description
		Danger	There is a dangerous situation on the route; for example, people are on the road.
		Traffic Any event that will cause a delay on a route.
		Weather	Weather conditions are adversely affecting a route; for example, there is ice on the road.
		Warnings There is a situation of which you should be aware on the route, but it is not serious enough to be considered a dangerous situation; for example, a minor accident has taken place.
		Forecast An event is expected to occur on a route.
		Restrictions There is a restricted flow of traffic on a route; for example, a lane has been closed on a motorway.
		Clearance	A traffic event that has now been cleared.
		Information All other events.
		Roadworks Roadworks are taking place on a route.

If a Traffic or Clearance event has a recommended detour, the following icons will display:

Event	Avoided Event	Message Type	Event Description
		Traffic Detour	A Traffic Event, for which a detour is recommended.
		Clearance Re-route	A Clearance Event, for which a re-route is recommended.

Avoided Event icons will only display on the Map screen, at the event location.

Third party recipient terms and conditions

The Legal Stuff

By activating, using and/or accessing the SUNA Traffic Channel, SUNA Predictive or other content or material provided by Intelematics (together, SUNA Products and/or Services), you must accept certain terms and conditions. The following is a brief summary of the terms and conditions that apply to you. To view the full terms and conditions relevant to your use of the SUNA Products and/or Services, please consult www.sunatraffic.com.au/termsandconditions/.

1. Acceptance

By using SUNA Products and/or Services, you will be deemed to have accepted and agreed to be bound by the terms and conditions fully detailed at www.sunatraffic.com.au/termsandconditions/.

2. Intellectual Property

SUNA Products and/or Services are for your personal use. You may not record, or retransmit the content, nor use the content in association with any other traffic information or route guidance service or device not approved by Intelematics. You obtain no right of ownership in any Intellectual Property Rights (including copyright) in the data that is used to provide SUNA Products and/or Services.

3. Appropriate Use

SUNA Products and/or Services are intended as an aid to personal motoring, and do not provide comprehensive or accurate information on all occasions. On occasions, you may experience additional delay as a result of using SUNA Products and/or Services. You acknowledge that it is not intended, or suitable, for use in applications where time of arrival or driving directions may impact the safety of the public or yourself.

4. Use of SUNA Products and Services while driving

You, and other authorised drivers of the vehicle in which SUNA Products and/or Services are installed and active, remain at all times responsible for observing all relevant laws and codes of safe driving. In particular, you agree to only actively operate SUNA Products and/or Services when the Vehicle is at a complete stop and it is safe to do so.

5. Service Continuity and Reception of the SUNA Traffic Channel

We will use reasonable endeavours to provide the SUNA Traffic Channel 24 hours a day, 365 days a year. The SUNA Traffic Channel may occasionally be unavailable for technical reasons or for planned maintenance. We will try to perform maintenance at times when congestion is light. We reserve the right to withdraw SUNA Products and/or Services at any time.

Also, we cannot assure the uninterrupted reception of the SUNA Traffic Channel RDS-TMC signal at any particular location.

6. Limitation of Liability

Neither Intelematics (nor its suppliers or the manufacturer of your device (the "Suppliers")) shall be liable to you or to any third party for any damages either direct, indirect, incidental, consequential or otherwise arising out of the use of or inability to use SUNA Products and/or Services even if Intelematics or a Supplier has been advised of the possibility of such damages. You also acknowledge that the neither Intelematics nor any Supplier guarantees nor make any warranties that relate to the availability, accuracy or completeness of SUNA Products and/or Services, and to the extent which it is lawful to do so, both Intelematics and each Supplier excludes any warranties which might otherwise be implied by any State or Federal legislation in relation to SUNA Products and/or Services.

7. Please Note

Great care has been taken in preparing this manual. Constant product development may mean that some information is not entirely up-to-date. The information in this document is subject to change without notice.

Copyright

© 2012 MiTAC International Corporation. Navman is either a registered trademark or trademark of MiTAC International Corporation and is used under licence by Navman Technology Limited. All rights reserved.

The software contains proprietary information of MiTAC International Corporation; it is provided under a licence agreement containing restrictions on use and disclosure and is also protected by copyright law. Reverse engineering of the software is prohibited.

No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording or otherwise, without the prior written permission of Navman.

Microsoft, Windows, Windows Vista, Windows 7, and Internet Explorer are either registered trademarks or trademarks of Microsoft Corporation in the United States and/or other countries. All rights reserved.

© 2012 Microsoft Corporation. All rights reserved. Microsoft, MSN, and the MSN logo are trademarks of the Microsoft group of companies.

The Bluetooth word mark and logos are owned by the Bluetooth SIG, Inc. and any use of such marks by Navman Technology Limited is under license.

Location Identifiers © 2012 International Air Transport Association.

POI Data © 2012 InfoUSA.

The software is based in part on the work of the Independent JPEG Group.

All other trademarks and registrations are the property of their respective owners.

Revision: R00

(09/2012)