WGCCH4NB - Multi-Station Frames HAGER - Free user manual and instructions

Product Type	Multi-gang frame for flush-mounted devices
Brand	Hager
Model	WGCCH4NB
Series Compatibility	Hager Muse and Hager Inspire
Number of Gangs	2 to 5 (depending on frame variant)
Dimensions - 2-gang Horizontal	172 x 86 mm
Dimensions - 3-gang Horizontal	258 x 86 mm
Dimensions - 4-gang Horizontal	344 x 86 mm
Dimensions - 5-gang Horizontal	430 x 86 mm
Vertical Dimensions (Hager Inspire)	2-gang: 86 x 172 mm, 3-gang: 86 x 258 mm
Compatible Wall Boxes	Standard flush-mounted wall boxes (connectable)
Compatible Centre Plates	Flush-mounted devices with centre plates 65 x 52 mm; for 52 x 52 mm, use accommodation ring; not compatible with 52 x 65 mm
Accommodation Ring	Required for centre plates 52 x 52 mm
Installation Location	Indoor areas with no drip or spray water
Installation Professional Required	Must be installed by a qualified electrician
Safety Warnings	Disconnect power before installation; electric shock hazard
Material	High-quality plastic (typical)
Color	White (typical)
Mounting Type	Snap-on onto device combination
Connection Method	Supplied connection bridges clipped into supporting plates
IP Rating	IP20 (estimated for indoor dry locations)

Frequently Asked Questions - WGCCH4NB HAGER

What is the Hager WGCCH4NB multi-gang frame used for?

The WGCCH4NB is a multi-gang frame used to combine 2 to 5 flush-mounted devices (switches, sockets, etc.) horizontally or vertically for a neat installation.

Which Hager series is the WGCCH4NB compatible with?

It is compatible with Hager Muse and Hager Inspire series. For Muse, no cover plate removal is needed; for Inspire, remove cover plates before mounting.

What are the dimensions of the 3-gang horizontal frame?

The 3-gang horizontal frame measures 258 x 86 mm (width x height).

Does the WGCCH4NB work with all centre plate sizes?

It works with most devices having centre plates of 65 x 52 mm. For 52 x 52 mm, an accommodation ring is required. It is not compatible with 52 x 65 mm plates.

How do I install the multi-gang frame?

Installation must be done by a qualified electrician. After wiring each device, fix them into wall boxes, connect them using supplied bridges, then snap the frame onto the assembly.

Can I install the frame outdoors?

No, it is only suitable for indoor use in areas without dripping or spray water.

What safety precautions should I take?

Always disconnect the power supply before installation to avoid electric shock. All live parts must be covered during work.

How do I clean the frame?

Clean with a soft, dry cloth. Do not use abrasive cleaners or immerse in water.

Are spare parts like accommodation rings available?

Yes, accommodation rings are available separately from Hager for centre plates 52 x 52 mm.

What is the maximum number of gangs supported?

The frame supports combinations from 2 to 5 gangs. The specific variant determines the exact gang count.

USER MANUAL WGCCH4NB HAGER

Electrical equipment must only be installed and assembled by a qualified electrician in accordance with the relevant installation standards, regulations, directives and safety and accident prevention directives of the country.

Failure to comply with these installation instructions may result in damage to the device, fire or other hazards.

Function

Multiple frames for 2gang to 5gang combinations of flush-mounted devices. Different versions for horizontal and vertical installation.

Hager Muse: The frames are compatible with most flush-mounted devices of the design with centre plates (Width x Height) = 65 x 52 mm.

In case of centre plates 52 x 52 mm, the accomodation ring must be used.

Not compatible with centre plates 52 x 65 mm.

Correct use

• For flush-mounted installation with standard connectable wall boxes.
• Only suitable for use in indoor areas with no drip and no spray water.

Technical data

Hager Muse:

Dimensions (Width x Height)

• 2gang horizontal 172 x 86 mm
• 3gang horizontal 258 x 86 mm
• 4gang horizontal 344 x 86 mm
• 5gang horizontal 430 x 86 mm

Hager Inspire:

Dimensions (Width x Height)

• 2gang horizontal 172 x 86 mm
• 3gang horizontal 258 x 86 mm
• 4gang horizontal 344 x 86 mm
• 5gang horizontal 430 x 86 mm
• 2gang vertical 86 x 172 mm
• 3gang vertical 86 x 258 mm

Information for electricians Installation and electrical connection

Preparing the devices for installation

■ Remove frame at every single device to be combined (see installation manual of the respective device).

Hager Inspire:

■ Furthermore, remove cover plate at every single device (see installation manual of the respective device).

Installing the devices into the wall boxes

(for example with "3gang frame (horizontal)")

DANGER!

Touching live parts can result in an electric shock.

An electric shock can lead to death.

Disconnect the connecting cables before working on the device and cover all live parts in the area!

• Arrange the devices horizontally or vertically in the desired order depending on frame type. Example here: horizontal.
  ■ Wire each device of the combination according to its wiring diagram (see installation manual of the respective device).

1

Technical diagram of three electrical wall-mounted components with wiring and screwdriver, showing internal circuitry (no text or labels)

■ After wiring, fix the devices with the screws into the wall boxes (1).

Connecting the devices for multiple combinations

(for example with "3gang frame (horizontal)")

The devices are connected via the supplied connection bridges (2). On the outside corners of its supporting plate each device has corresponding holes for fixing the bridges.

- Align one bridge per connection and clip the bridges one after the other in the supporting plates of the devices (2).

Assembling the covers

(for example with "3gang frame (horizontal)")

Hager Muse (3A):

In case of switches, fix the rockers onto each device.

In case of devices with centre plate 52 x 52 mm, place the accomodation ring onto the device (3A).
■ Then snap the multi-gang frame onto the device combination.

Hager Inspire (3B):

• Fix the rockers and cover plates onto each device.
  ■ Then snap the multi-gang frame onto the device combination.