HP60ICSX4 - Home Appliance Fisher & Paykel - Free user manual and instructions

USER MANUAL HP60ICSX4 Fisher & Paykel

BUILT-IN INTEGRATED RANGEHOOD

Safety and warnings 3

Installation instructions 5

Operating instructions 13

Cleaning and maintenance 14

Parts and accessories 16

Manufacturer's Warranty 17

Customer Care 19

IMPORTANT!

SAVE THESE INSTRUCTIONS

The models shown in this user guide may not be available in all markets and are subject to change at any time. For current details about model and specification availability in your country, please go to our website fisherpaykel.com or contact your local Fisher & Paykel dealer.

Registration

Register your product with us so we can provide you with the best service possible.

To register your product visit our website: fisherpaykel.com

! WARNING!

6.5 kg (HP60)

8.8 kg (HP90)

Weight Hazard

The appliance is heavy. Please ensure adequate care is taken when installing the appliance to prevent personal injury. The appliance must be installed onto a solid wall, stud, beam or truss. Weight of the product is 6.5 kg (HP60ICSX4) / 8.8 kg (HP90ICSX4).

! WARNING!

Electric Shock Hazard

Always disconnect the appliance from the mains power supply before carrying out any maintenance or repairs. Alterations to the domestic wiring system must only be made by a qualified electrician.

Failure to follow this advice may result in electrical shock or death.

IMPORTANT SAFETY INSTRUCTIONS

WARNING!

When using this appliance always exercise basic safety precautions including the following:

• Read the entire set of instructions before installing or using this appliance.
• Please make this information available to the person installing the appliance - doing so could reduce your installation costs.
• Always switch the power off prior to installation, servicing or cleaning of the rangehood.
• This appliance must be installed and connected to the mains power supply only by a suitably qualified person according to these installation instructions and in compliance with any applicable local building and electricity regulations. Failure to install the appliance correctly could invalidate any warranty or liability claims.
• To comply with electrical safety regulations, the rangehood must be plugged into a socket near the appliance. The socket must be accessible, or have an accessible isolating switch, to enable the end user to isolate the rangehood from the power for the purpose of internal cleaning or maintenance.
• A power outlet should be within 750 mm of the motor assembly and can either be on the wall, behind the chimney or in the ceiling.
• If the supply cord of this equipment is damaged, it must only be replaced by the manufacturer, its service agent or similarly qualified person in order to avoid a hazard.
• Ducting accessories are not supplied. All ducting must comply with local requirements and building codes.
• Attention should be given to ensure that any applicable regulations concerning the discharge of exhaust air are fulfilled.

SAFETY AND WARNINGS

• Before connecting any pipes, consult municipal ordinances to ensure that any applicable regulations concerning the discharge of exhaust air are adhered to and request permission from the person in charge of the building.
• Exhaust air must not be discharged into an existing flue that is used for exhausting fumes from appliances burning gas or other fuels.
• There shall be adequate ventilation of the room when the rangehood is used at the same time as appliances burning gas or other fuels.
• Range hoods and other cooking fume extractors may adversely affect the safe operation of appliances burning gas or other fuels (including those in other rooms) due to back flow of combustion gases. These gases can potentially result in carbon monoxide poisoning. After installation of a range hood or other cooking fume extractor, the operation of flued gas appliances should be tested by a competent person to ensure that back flow of combustion gases does not occur.
• The minimum distance between the supporting surface for cooking vessels on the cooktop and the lowest part of the rangehood shall be 600 mm. If the instructions for installation of the cooktop require a greater minimum distance, this should be followed.
• Stainless steel is very easily damaged during installation if abraded or knocked by tools. It is recommended to protect the top of the rangehood with cardboard or polystyrene during the installation to minimise the risk of damage occurring.
• To reduce the risk of damage occurring to the cooktop, it is recommended that the surface of the cooktop is protected with cardboard or a similar object during installation of the rangehood.
• This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning the use of the appliance by a person responsible for their safety.
• Children should be supervised to ensure they do not play with the appliance. Cleaning and user maintenance shall not be made by children without supervision.
• You must read the details concerning the method and frequency of cleaning.
  • There is a fire risk if cleaning is not carried out in accordance with the instructions.
• Never leave frying food unattended since grease can overheat and catch fire. The risk of fire is even greater in the case of used oil.
• Do not flambé under the rangehood.
• Never use the rangehood without the filters in place.
• During an electrostatic discharge (ESD) it is possible that the device will stop working. By switching the device off and on the device will again work as intended.
• CAUTION: accessible parts may become hot when used with cooking appliances.
• Remove all packaging, including protective wrappings, before use.

INSTALLATION INSTRUCTIONS

Parts Supplied

Technical line drawing of a mechanical component or enclosure with mounting brackets and a sloped top (no text or symbols)

Rangehood (1)

FISHER & PAYEEL BUILT-IN NINT ESCRATED RAN GEIGO O —— 2017.12.24

Installation guide / User guide (1)

Technical line drawing of a cylindrical mechanical component with mounting flanges (no text or symbols)

150 mm ducting adapter with non return flap (1)

13 mm screw (2)

Other Parts Required

Ducting - 150mm diameter, rigid or semi-rigid (not supplied)

Product and cabinetry cutout dimensions

HP60ICSX4 HP90ICSX4

PRODUCT DIMENSIONS		mm	mm
A	Overall height of product (with ducting adapter)	285(338)	315(372)
B	Overall width of product 492 792
C	Overall depth of product 277 277
D	Thickness of flange 2.5 2.5
E	Width of chassis 450 750
F	Depth of chassis 255 255
G	Height of side of chassis n/a 115
H	Width of top surface of chassis 251 410
I	Length of angled surface of chassis	300 261
J	Distance from centre of ducting outlet to back of chassis	161 84
K	Distance from centre of ducting outlet to side of chassis	225 375
L	Diameter of ducting outlet	150	150
	Length of power cord	1200	1200
CABINETRY CUTOUT DIMENSIONS
	Overall width of cutout	460	760
	Overall depth of cutout	260	260
O	Base of brackets/clips to bottom of chassis	min. 15 - max. 35	min. 15 - max. 35

IMPORTANT!

Actual product dimensions may vary by ± 2 mm.

Please read the entire instructions before installing the rangehood.

Note: If installing in cabinetry with base thickness >35mm remove material around the mounting surface so that the thickness is <35mm and the brackets/clips can engage with the surface (see below)

15mm \~ 35mm

INSTALLATION INSTRUCTIONS

Height of rangehood

Technical diagram showing a mechanical setup with a bracket, a moving cart, and a height dimension labeled 'P'

MINIMUM CLEARANCES		mm
P	Height from top of cooktop to base of rangehood	min. 600 - max.recommended 750

This rangehood must be installed no lower than the minimum height indicated in the table above. Minimum installation height may be greater if required by the cooktop manufacturer or safety and warnings section on this user guide. Installation at the minimum height will improve efficiency of capturing cooking odours, grease and smoke. Installation at the maximum height improves ergonomics by offering increased head room.

Induction cooking considerations

• Induction cooktops use energy efficient technology that only heats the contents of a cooking pot.
• Unlike gas or traditional electric cooktops, the surrounding air does not get heated when using an induction cooktop. As a result, rangehood filters, splashbacks and surrounding cabinetry do not get warmed up, increasing the likelihood of condensation on these cooler surfaces.
• Other factors like ambient temperature, humidity, natural ventilation of the room, size of the cookware and how the induction cooktop is being used also influence condensation. For example, aggressive boiling on high cooktop heat settings like PowerBoost increases the rate at which water is evaporated, increasing the likelihood of condensation.
• It is important to understand that neither the rangehood nor the induction cooktop are faulty as a result of this phenomenon.

Condensation can be minimised by:

• Installing the rangehood at the maximum height above the cooktop as specified in this user guide.
  • Using the rangehood on a lower speed setting when boiling.
  • Using the induction cooktop on a lower heat setting when boiling.
• Switching the rangehood on 5 minutes before cooking and letting it run for at least 5 minutes after cooking.

Venting options

Attention should be given to ensure that any applicable regulations concerning the discharge of exhaust air are fulfilled.

The rangehood can be installed to operate with the exhaust air ducted externally from the kitchen, or installed to operate with the exhaust air recirculating within the kitchen.

Ducted

For ducted installation it is recommended that 150 mm diameter, rigid or semi-rigid ducting is used. This will require a 160 mm (min) round hole in the ceiling or wall. Care should be taken to position the hole correctly.

For optimal efficiency use the shortest and straightest duct route possible and use rigid or semi-rigid ducting for reduced noise and increased airflow. Flexible metal ducting should only be used as a last resort (ie in difficult installations) and if used ensure that it is straight and smooth and extended as much as possible.

Pure mechanical cross-section diagram without any text, numbers, or symbols

Vent through roof

Cross-sectional diagram of a mechanical or architectural component with no visible text or symbols

Vent through external wall

Recirculating

Where ducting outside is not a practical option, this rangehood can be installed to operate with the air recirculating. Carbon filters are required to remove odours from the air before it is channelled back into the room or overhead bulkhead (refer to ‘Cleaning and Maintenance’ section).

Ensure that the ducting outlet is not obstructed, even a partial obstruction will restrict the efficiency of the rangehood.

Check with local codes and regulations if recirculation is allowed in your area.

Recirculate with carbon filters

IMPORTANT!

Venting directly into the cabinet with no ducting and louvered vent is not permitted.

To recirculate your perimeter insert range hoods:

① Determine the desired location of the 150mm louvered vent on your cabinetry.

The louvered vent can be placed on the side or front of your cabinet provided there is sufficient clearance form the surrounding cabinetry to enable ventilated air to recirculate back into your kitchen.

Note: Placement of the louvered vent on the top of your cabinetry is not recommended. This should be only be done if objects can be prevented from falling through the louvers in to the blower.

② Create a cutout in your cabinet to fit the 150mm louvered vent. Place the louvered vent on the hole created and secure (A).
③ Connect the blower outlet to the louvered vent with a length of 150mm rigid ducting, and secure the joints with aluminum tape. Ensure there is no slack in the ducting.

A

Isometric line drawing of a side top front view of an electronic device (no text or symbols on the diagram itself)

Isometric line drawing of a mechanical or electrical enclosure with a central cylindrical component and two side-mounted components (no text or symbols)

Isometric line drawing of a transparent enclosure with a circular vent and internal structure (no text or symbols)

Recirculation venting options

WARNING!

• This appliance is heavy and requires two persons for unpacking and installation.
• Installation work and electrical wiring must be done by qualified person(s) in accordance with all applicable codes and standards.
• Failure to install the screws or fixing device in accordance with these instructions may result in electrical hazards.

IMPORTANT!

Wear gloves to protect against sharp edges.

The manufacturer is not liable for any damage caused by not following these instructions.

INSTALLATION INSTRUCTIONS

INSTALLATION

1 Prepare for installation.

Before installing your rangehood:

• Please read the instructions carefully.
• Unpack the rangehood and check that all functions are working.
• Ensure that the voltage (V) and the frequency (Hz) indicated on the serial plate match the voltage and frequency at the installation site.
• The stainless steel and glass surfaces of the rangehood are very easily damaged during installation if grazed or knocked by tools. Please take care to protect the surfaces during installation.
• Protect the cooktop surface below with cardboard, or the like, to prevent damage occurring whilst the rangehood is being installed above.

2 Fit the 150 mm ducting adapter with non return flap to the rangehood using the screws supplied.

3 Provide an opening on the underside of the cupboard (see product and cabinetry cutout dimensions).

Depth Width

4 Remove the filter from the rangehood.

Technical line drawing of a rectangular electronic device with mounting holes and internal compartments (no text or symbols)

INSTALLATION INSTRUCTIONS

5 Connect duct and plug rangehood in.

Technical diagram showing installation of a cylindrical component with an electrical outlet, including a close-up view and a 3D layout.

6 Lift the rangehood and fit through the opening of the cupboard till the spring loaded brackets / clips hold the product in place.

Diagram of a device with two upward arrows indicating motion or movement, enclosed in a 3D box (no text or symbols)

7 Secure rangehood while tightening the brackets / clips.

Technical illustration showing a screwdriver inserted into a device and its internal panel view (no text or symbols)

OPERATING INSTRUCTIONS

Control panel

Six circular shapes with varying dot patterns and a small black dot, arranged horizontally (no text or symbols)

CONTROL PANEL FEATURES

	Lights Turn the lights on or off.
	Fan Turn the rangehood fan off.
	Fan speed 1 - 3	Turn the rangehood fan on or adjust the fan speed levels from 1 - 3 with 1 being the lowest level and 3 being the highest.

WARNING!

- Unplug or disconnect the appliance from the power supply before servicing or cleaning.

IMPORTANT!

• Never use abrasive or oil based cleaners.
• Wear gloves to protect against sharp edges.

Maintenance

The rangehood should be cleaned regularly using a mild, liquid detergent and a clean soft cloth to avoid a build-up of grease occurring. Avoid the use of corrosive chemicals, abrasive cleaning products, hard brushes and steel wool pads. Grease deposits are corrosive which can cause damage to your rangehood.

Note: in areas of high humidity or coastal environments, cleaning should be carried out more frequently.

Aluminium filters

• Depending on use, and at least once a month, the aluminium grease filters should be removed and cleaned with hot soapy water or in a dishwasher.
• If washed in a dishwasher, the filters should be placed in an upright position to prevent food from falling on them.
  • After rinsing and drying, replace the filters.

Line drawing of a cabinet or storage unit with multiple compartments and doors (no text or symbols)

Note: some discolouration of the frames may occur.

Removing the aluminium filters:

1 Pull the filter catch, tilting it downwards until it disengages from the supports.
2 Reverse these instructions when refitting the filters.

Carbon filters - for use in recirculation mode

Active carbon filters are disposable items designed to remove grease and odours from cooking vapours before the air is channelled back into the kitchen. The active carbon filters must be replaced periodically to work properly, at least once every three months, depending on the frequency with which the rangehood is used.

IMPORTANT!

• Carbon filters are disposable items and must be replaced at least every three months.
- Saturated carbon filters can become a barrier to air movement, therefore limiting your range hoods performance.
• In the event of a fire, grease laden filters could be flammable.

Fitting the carbon filters:

1 Ensure the range hood is switched off.
2 Remove the aluminum grease filters from the range hood.
3 Place a carbon filter on each side of the blower inlet (refer to A), turn the filter until it clips into place (refer to B).

Note: The direction will be clockwise on one side of the blower and counterclockwise on the other side of the blower.

4 Refit aluminium grease filters.

Technical line drawing of an electric motor with a separate fan blade (no text or symbols)

A

Technical illustration of a mechanical component with cross-sectional views showing internal structure (no text or symbols)

B

Light bulb replacement

To replace the lights you must contact your Haier trained and supported service technician. Refer to the haier website or your service and warranty book for contact details.

Note: lights are not user replaceable.

PARTS AND ACCESSORIES

ITEM	REFERENCE NUMBER
Aluminium filter (HP60ICSX4) 793597
Aluminium filter (HP90ICSX4) 793598
Recirculation carbon filter x2 792481

You automatically receive a 2 year Manufacturer's Warranty with the purchase of this rangehood covering parts and labour for servicing within the country of purchase.

Fisher & Paykel undertakes to:

Repair or, at its option, replace without cost to the owner either for material or labour any part of the product, the serial number of which appears on the product, which is found to be defective within TWO YEARS of the date of purchase.

Note: this Manufacturer's Warranty is an extra benefit and does not affect your legal rights.

This Manufacturer's Warranty DOES NOT cover

Ⓐ Service calls which are not related to any defect in the product. The cost of a service call will be charged if the problem is not found to be a product fault. For example:

① Correcting the installation of the product.
② Instructing you how to use the product.
③ Replacing house fuses or correcting house wiring or plumbing.
④ Correcting fault(s) caused by the user.
⑤ Noise or vibration that is considered normal, eg drain/fan sounds, refrigeration noises or user warning beeps.
⑥ Correcting damage caused by pests, eg rats, cockroaches, etc.
⑦ Replacement light bulbs.

⑧ Defects caused by factors other than:

① Normal domestic use; or
② Use in accordance with the product's user guide.

© Defects to the product caused by accident, neglect, misuse or 'act of God'.

The cost of repairs carried out by non-authorised repairers or the cost of correcting such unauthorised repairs.

⑤ Normal recommended maintenance as set out in the product's user guide.

⑤ Repairs when the appliance has been dismantled, repaired or serviced by other than a Fisher & Paykel Authorised Repairer or the selling dealer.

⑥ Pick-up and delivery.

Transportation or travelling costs involved in the repair when the product is installed outside the Fisher & Paykel Authorised Repairer's normal service area.

Nothing in this Manufacturer's Warranty is intended to, or does, limit any rights you may have under law to recover the costs of inspecting or returning the goods to us.

This product has been designed for use in a normal domestic (residential) environment. This product is not designed for any commercial use (whatsoever). Any commercial use by a customer will affect this product's Manufacturer's Warranty.

Service under this Manufacturer's Warranty must be provided by a Fisher & Paykel Authorised Repairer (refer to the 'Customer Care' section at the back of this book). Such service shall be provided during normal business hours. This Manufacturer's Warranty certificate should be shown when making any claim.

For Australian Customers

This Manufacturer's Warranty is an extra benefit and does not affect your legal rights. Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled to a replacement or refund for a major failure and for compensation for any other reasonably foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure.

Please keep this user guide in a safe place.

Before you call for service or assistance...

Check the things you can do yourself. Refer to the installation instructions and your user guide and check that:

① Your product is correctly installed.
② You are familiar with its normal operation.

If after checking these points you still need assistance or parts, please refer to your nearest Authorised Service Centre, Customer Care, or contact us through our website www.fisherpaykel.com.

In New Zealand if you need assistance...\*

Call your Fisher & Paykel retailer who is trained to provide information on your appliance, or if we can be of any further help, please contact our Customer Care Centre.

Toll Free: 0800 FP CARE or 0800 372 273

Fax: [phone]

Website: www.fisherpaykel.com

Postal address: Fisher & Paykel Appliances Ltd, PO Box 58550, Botany, Auckland 2163

If you need service...\*

Fisher & Paykel has a network of independent Fisher & Paykel Authorised Repairers whose fully trained technicians can carry out any service necessary on your appliance. Your dealer or our Customer Care Centre can recommend a Fisher & Paykel Authorised Repairer in your area.

In Australia if you need assistance...\*

Call the Fisher & Paykel Customer Care Centre and talk to one of our Customer Care Consultants.

Toll Free: 1300 650 590

Fax: [phone]

Website: www.fisherpaykel.com

Postal address: Fisher & Paykel Appliances Ltd, PO Box 798, Cleveland QLD 4163

If you need service...\*

Fisher & Paykel has a network of Fisher & Paykel trained and supported service technicians responsible for servicing only Fisher & Paykel branded appliances. Our Customer Care Centre can recommend a Fisher & Paykel trained and supported service technician in your area.

*If you call, write or contact our website please provide: your name and address, model number, serial number, date of purchase and a complete description of the problem. This information is needed in order to better respond to your request for assistance.

Product details can be found under the aluminium filter.

Registration

Register your product with us so we can provide you with the best service possible. To register your product visit our website: www.fisherpaykel.com

Complete and keep for safe reference:

Model

Serial No. ____

Purchase Date ____

Purchaser

Dealer

Suburb

Town

Country

The product specifications in this document apply to the specific products and models described at the date of issue. Under our policy of continuous product improvement, these specifications may change at any time. You should therefore check with your Dealer to ensure this document correctly describes the product currently available.

NZ AU

104078F 09.22