99-7876 - Kit voiture Metra - Free user manual and instructions
Find the device manual for free 99-7876 Metra in PDF.
User questions about 99-7876 Metra
0 question about this device. Answer the ones you know or ask your own.
Ask a new question about this device
Download the instructions for your Kit voiture in PDF format for free! Find your manual 99-7876 - Metra and take your electronic device back in hand. On this page are published all the documents necessary for the use of your device. 99-7876 by Metra.
USER MANUAL 99-7876 Metra
INSTALLATION INSTRUCTIONS FOR PART 99-7876
APPLICATIONS
HONDA Pilot 2009
99-7876
KIT FEATURES
• ISO Mount Radio Provision With Pocket
KIT COMPONENTS
• A) Radio Housing • B) Radio Housing Brackets
natural_image
Interior view of a car dashboard with air filters and control panels (no visible text or symbols)
natural_image
Technical line drawing of a mechanical component with no visible text or symbols
natural_image
Technical line drawing of two mechanical bracket components (no text or symbols)TOOLS REQUIRED:
Small Flat Blade Screwdriver • Panel Removal Tool
• Phillips Screwdriver • Wire Cutters
natural_image
Line drawings of four different screwdriver tools: a flat screwdriver, a pointed screwdriver, a standard screwdriver with pliers, and a flat tool (no text or symbols present)TABLE OF CONTENTS
Dash Disassembly
- HONDA Pilot 2009 ....1,2
Kit Preparation ....3
Kit Assembly
- ISO Mount Radio Provision With Pocket ....4
Final Assembly....5
*Note:
Refer also to the instructions included with the aftermarket radio.
HONDA PILOT 2009
1 Disconnect the negative battery terminal to prevent an accidental short circuit.
2 Unclip and remove the left a/c vent panel surrounding the shifter. (Figure A)
3 Unclip and remove the right a/c vent panel. (Figure A)
4 Remove the (2) Phillips screws securing the pocket below the radio then unclip and remove the pocket. (Figure B)
5 Remove (4) Phillips screws securing the radio, Unplug and remove the radio. (Figure C)
Continued on page 2.
natural_image
Interior view of an airplane cockpit with airbags and control panels (no text or symbols visible)
natural_image
Diagram of a car air conditioning unit with control panel and screw mechanism (no text or labels)
natural_image
Interior view of a car dashboard with air filters and control buttons (no text or symbols visible)HONDA PILOT 2009
6 Remove the (6) screws retaining the (3) clip assemblies at the top edge of the factory radio/climate control assembly. Retain screws and clip assemblies for reuse. (Figure D)
7 Remove (4) Phillips screws securing the factory climate control. Unplug and remove factory climate control.
NOTE: Retain (4) Phillips screws and climate control for reuse in Kit Assembly. (Figure E)
Continue to kit preparation.
text_image
D REAR VIEW SIDE OF RADIOE
text_image
REAR VIEW SIDE OF RADIO 1 SCREW ON EACH SIDE 1 SCREW ON EACH SIDEHONDA PILOT 2009
*Note: Refer also to the instructions included with the aftermarket radio.
1 Cut and remove support strut on radio housing. (Figure A)
2 Attach the (3) clips removed in step 6 of the disassembly to the 99-7876 radio housing using the factory hardware. (Figure B)
Continue to kit assembly.
A
natural_image
Technical line drawing of a mechanical component with internal forces and arrows indicating movement (no text or symbols)B
text_image
REAR VIEW RADIO HOUSINGISO MOUNT RADIO PROVISION WITH POCKET
*Note: Refer also to the instructions included with the aftermarket radio.
1 Attach the corresponding radio housing bracket to the radio housing (Figure A), then attach the climate control to the assembly using the (4) Phillips screws removed in step 7. (Figure B)
2 Position the aftermarket radio into the radio housing and secure using the hardware supplied with the radio. (Figure C)
Continue to final assembly.
natural_image
Technical line drawing of a mechanical housing component (no text or symbols)
text_image
B A/C MAX AC
natural_image
Technical line drawing of a car air conditioner unit with control panel and fan (no text or symbols)FINAL ASSEMBLY
text_image
A B C D(A) Strip wire ends back 1/2"
B) Twist ends together
C) Solder
D) Tape
1 Locate the factory wiring harness in the dash. Metra recommends using the proper mating adapter and making connections as shown. (Isolate and individually tape off the ends of any unused wires to prevent electrical short circuit.)
2 Re-connect the negative battery terminal and test the unit for proper operation.
3 Reassemble radio and dash assemblies in reverse order of disassembly.
FINAL WIRING CONNECTIONS
Make wiring connections using the EIA color code chart shown below and the instructions included with the head unit. Metra recommends making connections as shown below; Strip, Splice, Solder, Tape. Isolate and individually tape off ends of any unused wires to prevent electrical short circuit.
METRA / EIA WIRING CODE
| 12V Ignition / Acc......Red | Right Front (+)......Gray |
| 12V Batt / Memory......Yellow | Right Front (-)......Gray/ Black |
| Ground......Black* | Left Front (+)......White |
| Power Antenna......Blue | Left Front (-)......White / Black |
| Amp Turn-On......Blue / White | Right Rear (+)......Violet |
| Amp Ground......Black / White | Right Rear (-)......Violet / Black |
| Illumination......Orange | Left Rear (+)......Green |
| Dimmer......Orange / White | Left Rear (-)......Green / Black |
*NOTE: When a Black wire is not present, ground radio to vehicle chassis. All colors may not be present on all leads due to manufacturer's specifications.
99-7876 INSTRUCTIONS