FTFHP930 - USB Drive Halifax - Free user manual and instructions

Product Type	Type 1 Grease Rated Exhaust Hood
Brand	Halifax
Model	FTFHP930
Material	Stainless Steel
Listing	ANSI UL710 and CAN/ULC S646-10
Standards	NFPA 96
Warranty	24 months from date of shipment
Application	Commercial Kitchen
Installation Location	Roof of truck or mobile unit
Required Professional Installation	Yes, qualified professional only
Airflow Requirement	Must match hood size and installation design (CFM)
Filter Shipping	Typically shipped separately or in hood; remove packaging just before commissioning
Duct Connection	Weld on top of hood; cut hole in roof of truck
Roof Curb	Mount with curb plate and sealant
Bolt Kit	Concession Hood Bolt Kit: 8\" SS hex head screws, washers, nuts, ring gasket
Torque Specification	75 in-lbs; ensure Garlock washer does not deform
Clearance from Combustibles	Minimum 18 inches (Type 1); reduction methods in UL listing
Electrical	Wire power to fan per wiring diagram
Lighting	Optional; follow electrical diagram if installed
Sealant Required	Use around roof curb and all installation holes

Frequently Asked Questions - FTFHP930 Halifax

What standards does the Halifax FTFHP930 hood comply with?

The hood is listed to ANSI UL710 and CAN/ULC S646-10, and built to the NFPA 96 National Fire Protection Association Standard.

What is the warranty period for this hood?

The equipment is warranted for 24 months from the date of shipment against defects in materials and workmanship under normal use and service.

Can I install the hood myself?

No, installation must be performed only by a qualified professional to ensure safety and compliance with local codes.

Are filters included with the hood?

Filters are typically shipped in the hood or on a separate skid in original packaging. Do not remove packaging until just prior to commissioning.

What is the required clearance from combustible materials?

For Type 1 grease rated hoods, a minimum clearance of 18 inches is typically required. Clearance reduction methods are outlined in the manufacturer's UL listing and may be accepted by local authorities.

How do I attach the hood to the roof?

Use the Concession Hood Bolt Kit (included). Mark pilot holes 12 inches in at each end, drill through the hood and roof, then secure with bolts, washers, and nuts. Torque to 75 in-lbs.

What type of sealant should be used?

Use sealant around the roof curb and any holes made during installation to prevent leaks. Follow local codes and NFPA 96 recommendations.

Is this hood suitable for outdoor use?

The hood is designed for installation on a truck roof or similar mobile unit, but should be installed in a location protected from direct weather exposure unless specified otherwise.

How do I determine the correct airflow (CFM) for my hood?

The airflow must be designed for the size of hood, filters, and installation. Refer to the installation instructions or consult a qualified professional to ensure proper CFM.

What should I do if I receive the hood with missing parts?

Report shortages to your representative immediately. Confirm that only items on the bill of lading are accepted, and check for hidden or obvious damage upon receipt.

USER MANUAL FTFHP930 Halifax

Exterior view of a Halifax Hoods stainless steel kitchen air duct (no signage or text beyond branding)

HalifaxHoods

Receiving and Storage

Once equipment is received, check for both obvious and hidden damage. If damage is found, record all necessary information on the bill of lading and file a claim with the final carrier. Check to be sure that all parts of the shipment, including accessories, are accounted for.

UNPACKING

Verify that all required parts and the correct quantity of each item have been received. If any items are missing, report shortages to your representative to obtaining missing parts. Sometimes it is not possible that all items for the unit be shipped together due to availability of transportation and truck space. Confirmation of shipment(s) must be limited to only items on the bill of lading. Filters are typically shipped in the hood, but sometimes are shipped on a separate skid in their original packaging. Do not remove factory packaging or install filters until just prior to commissioning. Remove all other shipping/packing materials.

WARNING!!

Installation of this unit should only be performed by a qualified professional. Please read the instructions thoroughly before installing or servicing this equipment.

LISTING

This hood is listed to ANSI UL710 and CAN/ULC S646-10 and built to the "NFPA 96" National Fire Protection Association Standard

WARRANTY

This equipment is warranted to be free from defects in materials and workmanship, under normal use and service, for a period of 24 months from date of shipment – See full Installation Instructions for Details.

INSTALLATION

It is necessary to install and operate this unit with the airflow (CFM) designed for the size of hood, filters and installation based on the information provided.

HalifaxHoods

SITE PREPERATION

1. To safely lift equipment into the final installed position you must make sure the area of installation is clear. Make sure you have enough room after installation to service unit easily.

2. Verify the location that the hood will be installed so there is nothing to interfere when installing the unit.

3. Review your plans and specifications for your project.

4. Confirm and verify the supports will support the weight of the hood and fan mounted on top of the truck.

5. If installing light fixtures a. Have electrician following wiring diagram as noted in full Installation Manual

6. Weld Duct connection on top of Hood at area which does not interfere with bracing inside truck

7. Cut hole in Hood at duct connection - See Figure #1, Item #7

8. To cut the hole properly in the roof of truck - See Figure #1 a. Lift hood in the location where it will be mounted, ensuring there is adequate room available to install the hood and all ductwork to comply with proper clearances from combustible material (Item # 1) b. Bring duct in contact with top of truck (Item # 5) c. Mark location of duct on truck roof d. Lower hood back down e. Cut hole in roof of truck (Item # 7)

9. Mount Roof Curb with Curb plate on top of truck (Items # 3 & 4)

10. See attached instructions for using Concession Hood Bolt Kit to complete hood attachment

11. Curb Plate securing a. Cut Curb Plate hole where duct meets plate to ensure tight fit b. Secure Curb Plate to top of Roof Curb

12. Install and secure fan on top of Roof Curb (Item # 2)

13. Wire power to Fan

14. Use Sealant around roof curb and any holes which were made during the installation process IMC, NFPA96 and local authorities having jurisdiction may call for a minimum clearance (typically 18 inches for type 1, grease rated hoods) between the cooking hood(s), exhaust ducts, and building materials which are combustible. However, IMC and NFPA96 do outline acceptable clearance reduction methods; most local jurisdictioning authorities will accept the clearance reduction methods approved in the manufacturer's UL listing for Type 1, grease rated hoods.

HalifaxHoods

Bolt Kit

1. Use the "Concession Hood Bolt Kit" when installing the hood. The kit includes the following:

Hardware Description Quantity (Pcs)
8" Long SS hex head screw 1⁄2"-13 TPI 4
1⁄2" SS washers 16
1⁄2"-13 TPI SS Nuts 16
Ring Gasket .531"ID, 1.250"OD, .063"THK 4

1. Mark pilot holes, 12 inches in, at each end 4" from the front and rear of the Hood

2. Drill Pilot Holes

3. Align and raise the Hood in the location where it will be mounted

4. Drill the holes through the hood and exterior roof line were the hood will be mounted

5. Lower Hood back down

6. Remove any burrs and/or metal fragments around holes

7. See Figure 1 on back side of the sheet for installation

8. Torque all hardware to 75 in-lbs, unless the Garlock washer begins to deform

9. You may remove excess screw threads. There must be at least 1/16" of threads extending past the outward face of the properly torqued nut.

FIGURE 1