SuperServer E100-9S-L - Server Supermicro - Free user manual and instructions

USER MANUAL SuperServer E100-9S-L Supermicro

Line drawing of a SuperMicro industrial device with heat sinks and ports (no text or symbols on the device itself)

USER'S MANUAL

Revision 1.0

The information in this User's Manual has been carefully reviewed and is believed to be accurate. The vendor assumes no responsibility for any inaccuracies that may be contained in this document, and makes no commitment to update or to keep current the information in this manual, or to notify any person or organization of the updates. Please Note: For the most up-to-date version of this manual, please see our website at www.supermicro.com.

Super Micro Computer, Inc. ("Supermicro") reserves the right to make changes to the product described in this manual at any time and without notice. This product, including software and documentation, is the property of Supermicro and/or its licensors, and is supplied only under a license. Any use or reproduction of this product is not allowed, except as expressly permitted by the terms of said license.

IN NO EVENT WILL Super Micro Computer, Inc. BE LIABLE FOR DIRECT, INDIRECT, SPECIAL, INCIDENTAL, SPECULATIVE OR CONSEQUENTIAL DAMAGES ARISING FROM THE USE OR INABILITY TO USE THIS PRODUCT OR DOCUMENTATION, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. IN PARTICULAR, SUPER MICRO COMPUTER, INC. SHALL NOT HAVE LIABILITY FOR ANY HARDWARE, SOFTWARE, OR DATA STORED OR USED WITH THE PRODUCT, INCLUDING THE COSTS OF REPAIRING, REPLACING, INTEGRATING, INSTALLING OR RECOVERING SUCH HARDWARE, SOFTWARE, OR DATA.

Any disputes arising between manufacturer and customer shall be governed by the laws of Santa Clara County in the State of California, USA. The State of California, County of Santa Clara shall be the exclusive venue for the resolution of any such disputes. Supermicro's total liability for all claims will not exceed the price paid for the hardware product.

FCC Statement: This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the manufacturer's instruction manual, may cause harmful interference with radio communications. Operation of this equipment in a residential area is likely to cause harmful interference, in which case you will be required to correct the interference at your own expense.

California Best Management Practices Regulations for Perchlorate Materials: This Perchlorate warning applies only to products containing CR (Manganese Dioxide) Lithium coin cells. "Perchlorate Material-special handling may apply. See www.dtsc.ca.gov/hazardouswaste/perchlorate".

WARNING: Handling of lead solder materials used in this product may expose you to lead, a chemical known to the State of California to cause birth defects and other reproductive harm.

The products sold by Supermicro are not intended for and will not be used in life support systems, medical equipment, nuclear facilities or systems, aircraft, aircraft devices, aircraft/emergency communication devices or other critical systems whose failure to perform be reasonably expected to result in significant injury or loss of life or catastrophic property damage. Accordingly, Supermicro disclaims any and all liability, and should buyer use or sell such products for use in such ultra-hazardous applications, it does so entirely at its own risk. Furthermore, buyer agrees to fully indemnify, defend and hold Supermicro harmless for and against any and all claims, demands, actions, litigation, and proceedings of any kind arising out of or related to such ultra-hazardous use or sale.

Manual Revision 1.0

Release Date: February 28, 2018

Unless you request and receive written permission from Super Micro Computer, Inc., you may not copy any part of this document. Information in this document is subject to change without notice. Other products and companies referred to herein are trademarks or registered trademarks of their respective companies or mark holders.

Copyright © 2018 by Super Micro Computer, Inc.

All rights reserved.

Printed in the United States of America

Preface

About this Manual

This manual is written for professional system integrators and PC technicians. It provides information for the installation and use of the SuperServer E100-9S/-9S-E/-9S-L. Installation and maintenance should be performed by experienced technicians only.

Please refer to the E100-9S/-9S-E/-9S-L server specifications page on our website for updates on supported memory, processors and operating systems (http://www.supermicro.com).

Notes

For your system to work properly, please follow the links below to download all necessary drivers/utilities and the user's manual for your server.

• Supermicro product manuals: http://www.supermicro.com/support/manuals/
• Product drivers and utilities: ftp://ftp.supermicro.com
- Product safety info: http://www.supermicro.com/about/policies/safety_information.cfm

If you have any questions, please contact our support team at:

[e-mail]

This manual may be periodically updated without notice. Please check the Supermicro website for possible updates to the manual revision level.

Warnings

Special attention should be given to the following symbols used in this manual.

Warning! Indicates important information given to prevent equipment/property damage or personal injury.

Warning! Indicates high voltage may be encountered when performing a procedure.

Contents

Chapter 1 Introduction

1.1 Overview....7
1.2 System Features 8
1.3 I/O Features 9

Front I/O Features....9

Rear I/O Features ....10

1.4 Motherboard Layout....11

Quick Reference Table....12

System Block Diagram....13

1.5 System Installation ....14

Unpacking the System....14

Warnings and Precautions....14

Installing Components to your System ....14

Chapter 2 Maintenance and Component Installation

2.1 Removing Power....15
2.2 Accessing the System....16
2.3 Motherboard Components....17

Processor 17

Memory Support....17

Installing Memory....17

Solid State Storage ....18

Motherboard Battery ....18

Installing Mounting Brackets....19

Chapter 3 Motherboard Connections

3.1 Ports 20
3.2 LED Indicators....21
3.3 Headers and Connectors ....22

Control Panel 26

3.4 Jumper Settings 28

How Jumpers Work....28

Chapter 4 Software Installation

4.1 Driver Installation....30
4.2 SuperDoctor ^® 5....31

Chapter 5 BIOS

5.1 Introduction....32
Starting the Setup Utility ....32
5.2 Main Page 33
5.3 Advanced Page....34
5.4 Security....56
5.5 Boot....61
5.6 Save & Exit....64

Appendix A BIOS Error Codes

Appendix B Standardized Warning Statements for DC Systems

Appendix C System Specifications

Appendix D Traditional Chinese Version Safety Warnings

Appendix E UEFI BIOS Recovery

Contacting Supermicro

Headquarters

Address: Super Micro Computer, Inc.

980 Rock Ave.

San Jose, CA 95131 U.S.A.

Tel: [phone]

Fax: [phone]

Email: [e-mail] (General Information)

[e-mail] (Technical Support)

Website: www.supermicro.com

Europe

Address: Super Micro Computer B.V.

's-Hertogenbosch, The Netherlands

Tel: [phone]

Fax: [phone]

Email: [e-mail] (General Information)

[e-mail] (Technical Support)

[e-mail] (Customer Support)

Website: www.supermicro.nl

Asia-Pacific

Address: Super Micro Computer, Inc.

3F, No. 150, Jian 1st Rd.

Zhonghe Dist., New Taipei City 235

Taiwan (R.O.C)

Tel: [phone]

Fax: [phone]

Email: [e-mail]

Website: www.supermicro.com.tw

Chapter 1

Introduction

1.1 Overview

The SuperServer E100-9S/-9S-E/-9S-L is a compact, embedded system comprised of the SCE-101-01 chassis and the X11SSN-H-WOHS/-E-WOHS/-L-WOHS single processor motherboard. Refer to our website for information on operating systems that have been certified for use with the system (www.supermicro.com).

This chapter provides a brief outline of the functions and features. In addition to the motherboard and chassis, several important parts that are included with the system are listed below.

Main Parts List
Description Part Number Quantity
Power Adapter MCP-250-10117-0N 1

Important Links

For your system to work properly, follow the links below to download all necessary drivers and utilities for your server.

• Product drivers and utilities: ftp://ftp.supermicro.com
• Product safety info: http://www.supermicro.com/about/policies/safety_information.cfm
• If you have any questions, please contact our support team at: [e-mail]

This manual may be periodically updated without notice. Check the Supermicro website for possible updates to the manual revision level.

1.2 System Features

The following table provides an overview of the main features of the E100-9S/-9S-E/-9S-L. Refer to Appendix C for additional specifications.

System Features

Motherboard

E100-9S: X11SSN-H-WOHS

E100-9S-E: X11SSN-E-WOHS

E100-9S-L: X11SSN-L-WOHS

Chassis

SCE-101-01

CPU

E100-9S: 7th Generation Intel® Core i7-7600U Processor (System on Chip) Socket FCBGA 1356

E100-9S-E: 7th Generation Intel® Core i5-7300U Processor (System on Chip) Socket FCBGA 1356

E100-9S-L: 7th Generation Intel® Core i3-7100U Processor (System on Chip) Socket FCBGA 1356

I/O

2 x GLAN, 1 x HDMI 2.0, 1 x Display Port, 2 x USB 3.0, 1 x USB 3.1 Type C, 4 x USB 2.0, 4 x COM, 1 x DIO

Cooling

Fan-less design

Memory

Supports up to 32 GB DDR4 2133 MHz in 2 DIMM Slots

Expansion Slots

One full-size Mini-PCIe slot

One M.2 B-key 2280 (SATA/PCI-E or WWAN/GNSS) slot

Power

Lockable 60W Power Adapter for 12V DC

Hard Drives

Supports one M.2 SATA SSD B-Key 2280

Form Factor

3.5" SBC small form factor (4"X5.75")

Dimensions

(WxHxD) 7.68" x 5.94" x 1.73" in. (195 x 151 x 44 mm)

1.3 I/O Features

Front I/O Features

See the illustration below for the features included on the front of the chassis.

ANT 4 65 1 ANT SUFERMICRO HDMI 000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000

Front I/O Features
Item Features Description
1 Antenna Port	Two antenna ports
2 LAN Ports	Two 1Gbe LAN ports
3 USB Ports	Two USB 3.0 ports
4 USB 3.1c	Port A front USB 3.1	Type C port
5 Display Port	A front display port
6 HDMI Port	A front High-Definition Multimedia Interface port
7 Power Button		The main power switch applies or removes primary power from the power supply to the server but maintains standby power (Note: To perform most maintenance tasks, unplug the power cord to completely remove power)

Figure 1-1. Front I/O Overview

Rear I/O Features

The illustration below shows the features included on the rear of the chassis.

graph TD
    A["DC-IM 12V"] --> B["Component 1"]
    A --> C["Component 2"]
    A --> D["Component 3"]
    A --> E["Component 4"]
    B --> F["Component 3"]
    C --> G["Component 3"]
    D --> H["Component 3"]
    E --> I["Component 4"]
    F --> J["Component 5"]
    G --> J
    H --> J
    I --> J
    style A fill:#f9f,stroke:#333
    style B fill:#ccf,stroke:#333
    style C fill:#ccf,stroke:#333
    style D fill:#ccf,stroke:#333
    style E fill:#ccf,stroke:#333
    style F fill:#cfc,stroke:#333
    style G fill:#cfc,stroke:#333
    style H fill:#cfc,stroke:#333
    style I fill:#cfc,stroke:#333

Rear Chassis Features
Item Features Description
1 Power Input Port Port used for the 40W DC power input
2 DIO Port A rear mounted digital I/O port
3 USB Ports Four rear USB 2.0 ports
4 Grounding Screw Screw used for attaching an electrical grounding wire
5 COM Ports Four communication ports

Figure 1-2. Rear I/O Overview

1.4 Motherboard Layout

Below is a layout of the X11SSN-H-WOHS/-E-WOHS/-L-WOHS with jumper, connector, and LED locations shown. See the table on the following page for descriptions. For detailed descriptions, pinout information, and jumper settings, refer to Chapter 3.

FAN1 JPT1 JHDMI1 DP++ SRW1 USB6 (3.1) USB4/5 (3.0) LAN2 LAN1 JPME2 JD1 JF1 JGP1 JFW2 JPF1 JLCDPWR1 CPU LVDS1 JCOM1 JCOM2 SRW3 JCOM2 OSM3 OSM4 SRW4 JPH I SATA1 JH ALDOPT BT1 SERV1 JSRP(3.1) JSRP(3.0) JSRP(3.1) JSRP(3.0) JSRP(3.1) JSRP(3.0) JSRP(3.1) JSRP(3.0) JSRP(3.1) JSRP(3.0) JSRP(3.1) JSRP(3.0) JSRP(3.1) JSRP(3.0) JSRP(3.1) JSRP(3.0) JSR02 JCOM1 JCOM2 SRW4 JPH I SATA1 JH ALDOPT BT1 AUDIO FP Top Layout

SUPER DESIGNED IN USA JMD1 JSMBUS1 JMP1 X11SSN REV1.01 Bottom Layout JPW1 DIMMA1 DIMMB1

Figure 1-3. Motherboard Layout
Note: Components not documented are for internal testing only.

Quick Reference Table
Jumper Description Jumper Setting

JLCDPWR1 LVDS Panel VCC power source selection		Pin 1-3* (3.3V)Pin 3-5 (5V)Pin 3-4 (12V)
JPF1 FORCE POWER ON		Pin 1-2* (FORCE POWER ON)Pin 2-3 (POWER BUTTON ON)
JPME2 Manufacturing Mode		Pin 1-2* (Normal)Pin 2-3 (Manufacturing)
JPT1	TPM Enable/Disable Header(X11SSN-L does not support TPM)	Pin 1-2* (Enable)Pin 2-3 (Disable)

Connector Description

AUDIO FP Front Panel Audio Header (Mic-In/Headphone-Out)
BT1	Battery Connector(To Clear CMOS, remove the battery, short pins 1-2 for more than 10 seconds and install the battery.)
DP++ DisplayPort
FAN1 System Fan Header
I-SATA1 SATA 3.0 Port
JCOM1: COM1/COM2	COM Headers
JCOM2: COM3/COM4	(JCOM1 supports two RS232/RS422/RS485, JCOM2 supports two RS232)
JD1 Speaker Header (Pins 1-4)
JF1 Front Control Panel Header (Power/HDD LED, Reset, Power button)
JGP1 8-bit General Purpose I/O Header
JHDMI1 Back Panel HDMI 2.0 Port
JMD1	M.2 Slot B-KEY 2280 (PCIe x2 Gen3, one USB 2.0, one SATA 3.0)ww
JMP1 Full Size Mini PCI-E Slot with mSATA (one PCIe x1 Gen3, one USB 2.0, one SATA 3.0)
JPH1	SATA Power Connector (for one HDD systewwwwwwwwwwwwwwwwwwwwwwwwwwwwwwwwwwwwwwwwwwwwwwwwwwwwwwwwwwwwwwwwwwwwwwwwwwwwwwwwwwwwwwwwwwwwwwwwwwwwwwwwwwwwwwwwwwwwwwwwwwwwwwwwwwwwwwwwwwwwwwwwwwwwwwwwwwwwwwwwwwwwwwwwwwwwwwwwwwwwwwwwwwwwwwwwwwwwwwwwwWWW
JPW1	4-pin 12V R/A Type Power Connector (for X11SSN-H/E/L and X11SSN-H/E/L-WOHS)
JPW2	4-pin 12V Vertical Type Power Connector (for X11SSN-H/E/L-VDC)
JSMBUS1	System Management Bus Header
LAN1, LAN2 LAN (RJ45) Ports
LVDS1	Dual Channel 48-bit LVDS Connector
SRW1 - SRW4	M.2 and Mini PCI-E Mounting Holes
USB0/1	USB 2.0 x 2 Header
USB2/3	USB 2.0 x 2 Header
USB4/5	Back Panel USB 3.0 Ports
USB6	USB 3.1 Type C Port
USB7	USB 3.0 OTG Header (one USB 3.0, one USB 2.0)

(* Default Setting)

System Block Diagram

graph TD
    A["Intel"] -->|SPI| B["PCIe[3/4"]]
    A -->|USB 2.0["1"]| C["PCIe Gen3 x 1 or PCIe Gen2 x 2"]
    A -->|USB 3.0["1"]| D["PCIe Gen3 x 2"]
    A -->|USB 2.0["2"]| E["PCIe Gen2 x 1"]
    A -->|USB 3.0["3"]| F["PCIe Gen3 X1 to USB3.1"]
    A -->|USB 2.0["5"]| G["PCIe Gen3 x 2"]
    A -->|USB 2.0["6"]| H["PCIe Gen2 x 1"]
    A -->|USB 2.0["7"]| I["PCIe Gen2 x 1"]
    A -->|USB 2.0["8"]| J["PCIe Gen2 x 1"]
    A -->|USB 2.0["9"]| K["PCIe Gen2 x 1"]
    A -->|USB 2.0["10"]| L["SATA 6Gb/s"]
    A -->|USB 2.0["11"]| M["MUX"]
    A -->|USB 2.0["12"]| N["PCIe Gen3 x 1 or PCIe Gen2 x 2"]
    A -->|USB 2.0["13"]| O["PCIe Gen3 X1 to USB3.1"]
    A -->|USB 2.0["14"]| P["PCIe Gen3 X1 to USB3.1"]
    A -->|USB 2.0["15"]| Q["PCIe Gen3 X1 to USB3.1"]
    A -->|USB 2.0["16"]| R["PCIe Gen3 X1 to USB3.1"]
    A -->|USB 2.0["17"]| S["PCIe Gen3 X1 to USB3.1"]
    A -->|USB 2.0["18"]| T["PCIe Gen3 X1 to USB3.1"]
    A -->|USB 2.0["19"]| U["PCIe Gen3 X1 to USB3.1"]
    A -->|USB 2.0["20"]| V["PCIe Gen3 X1 to USB3.1"]
    A -->|USB 2.0["21"]| W["PCIe Gen3 X1 to USB3.1"]
    A -->|USB 2.0["22"]| X["PCIe Gen3 X1 to USB3.1"]
    A -->|USB 2.0["23"]| Y["PCIe Gen3 X1 to USB3.1"]
    A -->|USB 2.0["24"]| Z["PCIe Gen3 X1 to USB3.1"]
    A -->|USB 2.0["25"]| AA["PCIe Gen3 X1 to USB3.1"]
    A -->|USB 2.0["26"]| AB["PCIe Gen3 X1 to USB3.1"]
    A -->|USB 2.0["27"]| AC["PCIe Gen3 X1 to USB3.1"]
    A -->|USB 2.0["28"]| AD["PCIe Gen3 X1 to USB3.1"]
    A -->|USB 2.0["29"]| AE["PCIe Gen3 X1 to USB3.1"]
    A -->|USB 2.0["30"]| AF["PCIe Gen3 X1 to USB3.1"]
    A -->|USB 2.0["31"]| AG["PCIe Gen3 X1 to USB3.1"]
    A -->|USB 2.0["32"]| AH["PCIe Gen3 X1 to USB3.1"]
    A -->|USB 2.0["33"]| AI["PCIe Gen3 X1 to USB3.1"]
    A -->|USB 2.0["34"]| AJ["PCIe Gen3 X1 to USB3.1"]
    A -->|USB 2.0["35"]| AK["PCIe Gen3 X1 to USB3.1"]
    A -->|USB 2.0["36"]| AL["PCIe Gen3 X1 to USB3.1"]
    A -->|USB 2.0["37"]| AM["PCIe Gen3 X1 to USB3.1"]
    A -->|USB 2.0["38"]| AN["PCIe Gen3 X1 to USB3.1"]
    A -->|USB 2.0["39"]| AO["PCIe Gen3 X1 to USB3.1"]
    A -->|USB 2.0["40"]| AP["PCIe Gen3 X1 to USB3.1"]
    A -->|USB 2.0["41"]| AQ["PCIe Gen3 X1 to USB3.1"]
    A -->|USB 2.0["42"]| AR["PCIe Gen3 X1 to USB3.1"]
    A -->|USB 2.0["43"]| AS["PCIe Gen3 X1 to USB3.1"]
    A -->|USB 2.0["44"]| AT["PCIe Gen3 X1 to USB3.1"]
    A -->|USB 2.0["45"]| AU["PCIe Gen3 X1 to USB3.1"]
    A -->|USB 2.0["46"]| AV["PCIe Gen3 X1 to USB3.1"]
    A -->|USB 2.0["47"]| AW["PCIe Gen3 X1 to USB3.1"]
    A -->|USB 2.0["48"]| AX["PCIe Gen3 X1 to USB3.1"]
    A -->|USB 2.0["49"]| AY["PCIe Gen3 X1 to USB3.1"]
    A -->|USB 2.0["50"]| AZ["PCIe Gen3 X1 to USB3.1"]
    A -->|USB 2.0["51"]| BA["PCIe Gen3 X1 to USB3.1"]
    A -->|USB 2.0["52"]| BB["PCIe Gen3 X1 to USB3.1"]
    A -->|USB 2.0["53"]| BC["PCIe Gen3 X1 to USB3.1"]
    A -->|USB 2.0["54"]| BD["PCIe Gen3 X1 to USB3.1"]
    A -->|USB 2.0["55"]| BE["PCIe Gen3 X1 to USB3.1"]
    A -->|USB 2.0["56"]| BF["PCIe Gen3 X1 to USB3.1"]
    A -->|USB 2.0["57"]| BG["PCIe Gen3 X1 to USB3.1"]
    A -->|USB 2.0["58"]| BH["PCIe Gen3 X1 to USB3.1"]
    A -->|USB 2.0["59"]| BI["PCIe Gen3 X1 to USB3.1"]
    A -->|USB 2.0["60"]| BJ["PCIe Gen3 X1 to USB3.1"]

Figure 1-4. System Block Diagram

Note: This is a general block diagram and might not exactly represent the features on your motherboard. See the System Specifications appendix for the actual specifications of your motherboard.

1.5 System Installation

This section provides advice and instructions for mounting your system. The system is shipped with the onboard processor and the motherboard installed in the chassis.

Unpacking the System

Inspect the box in which the system was shipped and note if it was damaged. If the system itself shows damage, file a damage claim with the carrier.

Warnings and Precautions

Review the electrical and general safety precautions in Appendix B.

Installing Components to your System

• Memory: If your system is not already fully integrated with system memory, refer to Chapter 2 for details on compatible types of memory and the installation procedure.
• Drives and Storage: Refer to Chapter 2 for instructions on installing drives.
• Installing Mounting Brackets: Refer to Chapter 2 for instructions on installing mounting brackets.
• Input/Output: Refer to Chapter 3 for information about I/O ports.
• Software: Refer to Chapter 4 for software installation information, including drivers and monitoring programs.

Chapter 2 Maintenance and Component Installation

This chapter provides instructions on installing and replacing main system components. To prevent compatibility issues, only use components that match the specifications and/or part numbers given.

Installation or replacement of most components require that power first be removed from the system. Please follow the procedures given in each section.

2.1 Removing Power

Use the following procedure to ensure that power has been removed from the system. This step is necessary when removing or installing non-hot-swap components or when replacing a non-redundant power supply.

1. Use the operating system to power down the system.
2. After the system has completely shut down, disconnect the power cord from the power source.
3. Disconnect the power cord from the chassis.

2.2 Accessing the System

The E100-9S/-9S-E/-9S-L features a removable bottom cover to access to the inside of the chassis.

Technical diagram of an electronic device showing internal components with numbered labels and a green upward arrow indicating motion or orientation.

Figure 2-1. Removing the Chassis Cover

Removing the Bottom Cover

1. Power down the system as described in section 2.1.
2. Remove the eight screws that hold the cover in place.
3. Lift the cover up and off the chassis.

Caution: Except for short periods of time, do not operate the server without the cover in place. The chassis cover must be in place to prevent misuse.

2.3 Motherboard Components

Processor

The E100-9S/-9S-E/-9S-L features an embedded Intel® processor. E100-9S supports 7th Generation Intel Core i7-7600U Processor, E100-9S-E supports 7th Generation Intel Core i5-7300U Processor and E100-9S-L supports 7th Generation Intel Core i3-7100U Processor.

Memory Support

The X11SSN-H-WOHS/-E-WOHS/-L-WOHS series motherboard supports up to 32GB of DDR4 Non-ECC SODIMM memory with speeds up to 2133 MHz in two memory slots.

Note: Check the Supermicro website for recommended memory modules.®

Installing Memory

Caution: Exercise extreme care when installing or removing DIMM modules to prevent damage.

SO-DIMM Installation

Align

1. Position the SODIMM module's bottom key so it aligns with the receptive point on the slot.

2. Insert the SODIMM module vertically at about a 45 degree angle. Press down until the module locks into place.

Insert this end first Press down until the module locks into place.

1. The side clips will automatically secure the SODIMM module, locking it into place.

Locking clip

SODIMM Removal

1. Push the side clips at the end of slot to release the SO-DIMM module.
2. Pull the SO-DIMM module up to remove it from the slot.

Solid State Storage

The E100-9S/-9S-E/-9S-L motherboard deploys a B-KEY for SATA/PCIe SSD devices or USB/PCIe WWAN or GNSS card. The E100-9S/-9S-E/-9S-L deploys a 2280 screw hole location for an M.2 module.

Technical line drawings of an internal electronic device showing two views (top and side), no text or symbols present.

Figure 2-2. Installing an M.2 Expansion Card

Installing the M.2 Card

1. Gently insert the M.2 card into the connector.
2. Use a screw to secure the M.2 card to the M2_SRW1 standoff.

Motherboard Battery

The motherboard uses non-volatile memory to retain system information when system power is removed. This memory is powered by a lithium battery residing on the motherboard.

Installing Mounting Brackets

The chassis includes mounting brackets that allow it to be mounted in any convenient space.

1. Install the brackets to the chassis with two screws in each bracket.

2. Secure the brackets to the surface where you want the server to be mounted.

SIPR CICRC

Figure 2-3. Installing Mounting Brackets (Brackets extending out from the chassis)

Chapter 3

Motherboard Connections

This section describes the connections on the motherboard and provides pinout definitions. Depending on how the system is configured, not all connections are required. The LEDs on the motherboard are also described here. A motherboard layout indicating component locations can be found in Chapter 1.

Review the Safety Precautions in Appendix B before installing or removing components.

3.1 Ports

LAN Ports

Two LAN ports (JLAN1 - JLAN2) are located on the I/O back panel. These ports accept RJ45 type cables. Refer to the LED Indicator section for LAN LED information. Refer to the table below for pin definitions.

LAN PortPin Definition
Pin# Definition Pin# Definition
1 TD1+	11 YEL-
2 TD1-	12 YEL+
3 TD2+	13 GRN-/ORG+
4 TD2-	14 GRN+/ORG-
5 CT_VCC 15
6 CT_VCC 16
7 TD3+	17
8 TD3-	18
9 TD4+	19
10 TD4-	20

HDMI Port

The HDMI (High-Definition Multimedia Interface) port is used to display both high definition video and digital sound through an HDMI-capable display, using the same cable.

Universal Serial Bus (USB) Ports

There are two USB 3.0 ports (USB4/5) and one USB 3.0 Type C port (USB6) on the I/O back panel. The motherboard also has four front access USB 2.0 headers (USB0/1 and USB2/3). The onboard headers can be used to provide front side USB access with a cable. Two USB 2.0 cables for front panel support are included with the motherboard.

Back Panel USB 3.0Pin Definitions
Pin# Definition Pin# Definition
A1 VBUS B1 VBUS
A2 D1-N B2 D2-N
A3 D1-P B3 D2-P
A4 GND B4 GND
A5 Stda_SSRX1-N B5 Stda_SSRX2-N
A6 Stda_SSRX1-P B6 Stda_SSRX2-P
A7 GND_DRAIN B7 GND_DRAIN
A8 Stda_SSTX1-N B8 Stda_SSTX2-N
A9 Stda_SSTX1-P B9 Stda_SSTX2-P

Front Panel USB 2.0 Ports 2/3Header Pin Definitions
Pin# Definition		P	n# Definition
1	P5V_DUAL_F	2	P5V_DUAL_F
3	USBCON_N4	4	USBCON_N5
5	USBCON_P4	6	USBCON_P5
7	Ground	8	Ground
9	N/A	10	N/A

DP++

DisplayPort, developed by the VESA consortium, delivers digital display and fast refresh rate. It can connect to virtually any display device using a DisplayPort adapter for devices such as VGA, DVI, or HDMI.

3.2 LED Indicators

LAN Port LEDs

There are two LAN ports (JLAN1 and JLAN2) on the I/O back panel of the motherboard. Each Ethernet LAN port has two LEDs. The green LED indicates activity, while the other Link LED may be green, amber, or off to indicate the speed of the connection.

LAN1/2 LED(Connection Speed Indicator)
LED Color	Definition
Off	10 Mb/s
Green	100 Mb/s
Amber	1 Gb/s

3.3 Headers and Connectors

SATA Power Connector

The 4-pin SATA power connector JPH1 provides power to onboard HDD devices. Refer to the table below for pin definitions.

4-pin HDD Power Pin Definitions
Pin# Definition
1 12V
2-3 Ground
4 5V

12V Vertical Type Power Connector

JPW2 is the 12V DC power source for the X11SSN-H-WOHS/-E-WOHS/-L-WOHS motherboard.

3 4 1 2

+12V Vertical Type Power Pin Definitions
Pin# Definition
1 GND
2 GND
3 +12VSB
4 +12VSB

Required Connection

4-pin 12V R/A Type Power Connector

The R/A type power connector is located at JPW1 on the bottom side of the X11SSN-H-WOHS/-E-WOHS/-L-WOHS motherboard. Refer to the table below for pin definitions.

1 2 3 4

+12V R/A Type Power Pin Definitions
Pin# Definition
1 GND
2 GND
3 +12VB
4 +12VB

Required Connection

Front Panel Audio Header

A 10-pin front panel audio header located on the motherboard allows you to use the onboard sound for audio playback. Connect an audio cable to the this header to use this feature. Refer to the table below for pin definitions.

Audio HeaderPin Definitions
Pin# Definition Pin# Definition
1 Microphone_Left 2 Audio_Ground
3 Microphone_Right 4 Audio_Detect
5 Line_2_Right 6 Ground
7 Jack_Detect 8 Key
9 Line_2_Left 10 Ground

COM Ports

There are four COM ports (JCOM1: COM1/COM2 supports two RS232/RS422/RS485 and JCOM2: COM3/COM4 supports two RS232) on the motherboard. Refer to the table below for pin definitions.

Serial COM Ports (JCOM1)Pin Definitions
Pin# Definition		Pin# Definition
1	DCD1or RS-485/422_COM1_TX-(Full Duplex)or RS-485_COM1_Data-(Half Duplex)	2	DSR1
3	RXD1or RS-485/422_COM1_TX+(Full Duplex)or RS-485_COM1_Data+(Half Duplex)	4	RTS1
5	TXD1 or RS-485/422_COM1_RX+(Full Duplex)	6	CTS1
7	DTR1 or RS-485/422_COM1_RX-(Full Duplex)	8	RI1_N
9 GND	10	N/A
11	DCD2or RS-485/422_COM2_TX-(Full Duplex)or RS-485_COM2_Data-(Half Duplex)	12	DSR2
13	RXD2or RS-485/422_COM2_TX+(Full Duplex)or RS-485_COM2_Data+(Half Duplex)	14	RTS2
15	TXD2 or RS-485/422_COM2_RX+(Full Duplex)	16	CTS2
17	DTR2 or RS-485/422_COM2_RX-(Full Duplex)	18	RI_N2
19	GND	20	N/A

Serial COM Ports (JCOM2)Pin Definitions
Pin# Definition Pin# Definition
1 DCD3	2 DSR3
3 RXD3	4 RTS3
5 TXD3	6 CTS3
7 DTR3	8 RI3_N
9 GND	10	N/A
11	DCD4	12	DSR4
13	RXD4	14	RTS4
15	TXD4	16	CTS4
17	DTR4	18	RI4_N
19	GND	20	N/A

SATA Port

The X11SSN-H-WOHS/-E-WOHS/-L-WOHS has one SATA 3.0 port (I-SATA1).

Battery Connector

BT1 is a two-pin connector for an external CMOS battery. Refer to section 3.4 for battery installation instructions. This connector is also used to clear the CMOS. To clear the CMOS, remove the battery, short pins 1-2 for more than 10 seconds and then install the battery.

General Purpose I/O Header

The JGP1 (General Purpose Input/Output) header is an 8-bit general purpose I/O expander on a pin header via the SMBus. Refer to the table below for pin definitions.

GPIO HeaderPin Definitions
Pin# Definition Pin# Definition
1 P3V3SB 2 GND
3 GP_P3V3_GP0 4 GP_P3V3_GP4
5 GP_P3V3_GP1 6 GP_P3V3_GP5
7 GP_P3V3_GP2 8 GP_P3V3_GP6
9 GP_P3V3_GP3 10 GP_P3V3_GP7

Speaker

Connect a cable to pins 1-4 on the JD1 header to use an external speaker. Refer to the table below for pin definitions.

Speaker Connector Pin Definitions
Pin# Signal
1 P5V
2 NC
3 NC
4 R_SPKPIN

M.2 Slot

M.2 is formerly known as Next Generation Form Factor (NGFF) and is located at JMD1 on the bottom side of the motherboard. The M.2 slot is designed for internal mounting devices. The X11SSN-H-WOHS/-E-WOHS/-L-WOHS motherboard deploys a B-KEY for SATA/PCIe SSD devices or USB/PCIe WWAN or GNSS card. The X11SSN-H-WOHS/-E-WOHS/-L-WOHS deploys a 2280 screw hole location for an M.2 module.

System Management Bus Header

A System Management Bus header for additional slave devices or sensors is located at JSMBUS1 on the bottom side of the motherboard. Refer to the table below for pin definitions.

SMBus HeaderPin Definitions
Pin#	Definition
1	SMB_DATA
2	GND
3	SMB_CLK
4	NC

Mini PCI-E Slot

The Mini PCI-E slot, located at JMP1 on the bottom side of the motherboard, is used to install compatible Mini PCI-E and mSATA devices. The Mini PCI-E slot supports USB, one PCI-E, SATA devices, mSATA SSD, and wireless devices such as GNSS and Bluetooth modules. See the table below for pin definitions.

Mini PCI-EPin Definitions
Pin# Definition Pin# Definition
52 +3.3Vaux 51 NC
50 GND 49 NC
48 +1.5V 47 NC
46 NC 45 NC
44 NC 43 NC
42 NC 41 +3.3Vaux
40 GND 39 NC
38 USB_D+ 37 GND
36 USB_D- 35 GND
34 GND 33 PETp0
32 SMB_DATA 31 PETn0
30 SMB_CLK 29 GND
28 +1.5V 27 GND
26 GND 25 PERp0
24 +3.3Vaux 23 PERn0
22 PERST# 21 DET_CARD_			PLUG
20 NC 19 NC
18 GND 17 NC
16 NC 15 GND
14 NC 13 REFCLK+
12 NC 11 REFCLK-
10 NC 9 GND
8 NC 7 CLKREQ#
6 1.5V	5	NC
4 GND 3 NC
2 3.3Vaux	1	WAKE#

Control Panel

JF1 contains header pins for various buttons and indicators that are normally located on a control panel at the front of the chassis. These connectors are designed specifically for use with Supermicro chassis. Refer to the figure below for the descriptions of the front control panel buttons and LED indicators.

PWR Reset Power Button Reset Button 3.3V 3.3V Stby 1 2 Ground Ground HDD LED Power LED 7 8

Power Button

The Power Button connection is located on pins 1 and 2 of JF1. Momentarily contacting both pins will power on/off the system. This button can also be configured to function as a suspend button with a setting in the BIOS (see Chapter 4). To turn off the power in the suspend mode, press the button for at least 4 seconds. Refer to the table below for pin definitions.

Power ButtonPin Definition (JF1)
Pin#	Definition
1	Power Button
2	GND

Reset Button

The Reset Button connection is located on pins 3 and 4 of JF1. Attach it to a hardware reset switch on the computer case to reset the system. Refer to the table below for pin definitions.

Reset ButtonPin Definition (JF1)
Pin#	Definition
3 Reset
4 Ground

HDD LED

The HDD LED connection is located on pins 5 and 6 of JF1. Attach a cable here to indicate the status of HDD-related activities, including SATA activities. Refer to the table below for pin definitions.

HDD LEDPin Definition (JF1)
Pin#	Definition
5 +3	3V
6 HDD	Active LOW

Power LED

The Power LED connection is located on pins 7 and 8 of JF1. Refer to the table below for pin definitions.

Power LEDPin Definition (JF1)
Pin#	Definition
7 +3.3VSB
8 Power LED LOW

3.4 Jumper Settings

How Jumpers Work

To modify the operation of the motherboard, jumpers can be used to choose between optional settings. Jumpers create shorts between two pins to change the function of the connector. Pin 1 is identified with a square solder pad on the printed circuit board. See the diagram below for an example of jumping pins 1 and 2. Refer to the motherboard layout page for jumper locations.

Note: On two-pin jumpers, Closed means the jumper is on and Open means the jumper is off the pins.

Connector Pins Jumper Setting 3 2 1 3 2 1

JLCDPWR1

Use this jumper to select the power voltage for the LVDS panel. Make sure that the specifications of the cable is compatible with the panel to prevent damage.

LVDS Panel Power Source Selection Jumper Settings
Jumper Setting Definition
Pins 1-3 3.3V (Default)
Pins 3-5 5V
Pins 3-4 12V

Force Power On

Use jumper JLCDPWR1 (Pins 1-2) to select the FORCE POWER ON function. The system will boot up automatically without pressing the power button. See the table below for jumper setting information.

Force Power OnJumper Settings

Jumper Setting Definition

Pins 1-2 Force Power On (Default)

Pins 2-3 PWR BTN Power On

Manufacturing Mode Select

Close JPME2 to bypass SPI flash security and force the system to use the Manufacturing Mode, which will allow you to flash the system firmware from a host server to modify system settings. Refer to the table below for jumper settings.

Manufacturing ModeJumper Settings
Jumper Setting Definition
Pins 1-2 Normal	(Default)
Pins 2-3 Manufacturing Mode

TPM Enable/Disable

Use the JPT1 jumper to enable or disable the TPM feature. Refer to the table below for jumper settings.

TPM Enable/DisableJumper Settings
Jumper Setting Definition
Pins 1-2 Enable	(Default)
Pins 2-3 Disable

Chapter 4

Software Installation

This section describes the installation of drivers and management programs for the system.

4.1 Driver Installation

The Supermicro FTP site contains drivers and utilities for your system at ftp://ftp.supermicro.com. Some of these must be installed, such as the chipset driver.

After accessing the FTP site, go into the CDR_Images directory and locate the ISO file for your motherboard. Download this file to create a DVD of the drivers and utilities it contains. (You may also use a utility to extract the ISO file if preferred.)

After creating a DVD with the ISO files, insert the disk into the DVD drive on your system and the display shown in Figure 4-1 should appear.

Another option is to go to the Supermicro website at http://www.supermicro.com/products/. Find the product page for your motherboard here, where you may download individual drivers and utilities to your hard drive or a USB flash drive and install from there.

Note: To install the Windows OS, please refer to the instructions posted on our website at http://www.supermicro.com/support/manuals/.

SUPERMICRO X11SSN-H/L/E Motherboard Drivers & Tools (Win7) Intel Kaby Lake SoC X11SSN-H/L/E SUPERMICRO Computer Inc. Intel Chipset INF files Microsoft .Net Framework (Optional) ASPEED Graphics Driver Intel USB 3.0 Drivers Intel PRO Network Connections Drivers Trusted Platform Module Driver (Optional) SUPERMICRO SuperDoctor 5 Build driver diskettes and manuals Browse CD Auto Start Up Next Time For more information, please visit SUPERMICRO's web site.

Figure 4-1. Driver & Tool Installation Screen

Note: Click the icons showing a hand writing on paper to view the readme files for each item. Click the computer icons to the right of these items to install each item (from top to the bottom) one at a time. After installing each item, you must re-boot the system before moving on to the next item on the list. The bottom icon with a CD on it allows you to view the entire contents.

4.2 SuperDoctor® 5

The Supermicro SuperDoctor 5 is a hardware monitoring program that functions in a command-line or web-based interface in Windows and Linux operating systems. The program monitors system health information such as CPU temperature, system voltages, system power consumption, fan speed, and provides alerts via email or Simple Network Management Protocol (SNMP).

SuperDoctor 5 comes in local and remote management versions and can be used with Nagios to maximize your system monitoring needs. With SuperDoctor 5 Management Server (SSM Server), you can remotely control power on/off and reset chassis intrusion for multiple systems with SuperDoctor 5 or IPMI. SD5 Management Server monitors HTTP, FTP, and SMTP services to optimize the efficiency of your operation.

Note: The default User Name and Password for SuperDoctor 5 is ADMIN / ADMIN.

SuperDoctor 5 Health Info Systems Info Configuration Report Power Control Motherboard: XBD TU-LN4+ Fan Speed 784 FAN 5 783 FAN 6 Voltage CPB1 Vcc CPB2 DMM +1.3 V -5 V +1VGE +22 V Temperature System Temp P1-QMMGA P1-QMAQA P1-QBWA Status Chassis Ins PI Status

Figure 4-2. SuperDoctor 5 Interface Display Screen (Health Information)

Chapter 5

BIOS

5.1 Introduction

This chapter describes the AMI BIOS setup utility for the X11SSN-H-WOHS/-E-WOHS/-L-WOHS motherboard. It also provides the instructions on how to navigate the AMI BIOS setup utility screens. The AMI ROM BIOS is stored in a Flash EEPROM and can be easily updated.

Note: Due to periodic changes to the BIOS, some settings may have been added or deleted and might not yet be recorded in this manual. Please refer to the Manual Download area of our website for any changes to BIOS that may not be reflected in this manual.

Starting the Setup Utility

To enter the BIOS Setup Utility, hit the key while the system is booting-up. (In most cases, the key is used to invoke the BIOS setup screen. There are a few cases when other keys are used, such as , , etc.) Each main BIOS menu option is described in this manual.

The Main BIOS screen has two main frames. The left frame displays all the options that can be configured. "Grayed-out" options cannot be configured. The right frame displays the key legend. Above the key legend is an area reserved for a text message. When an option is selected in the left frame, it is highlighted in white. Often a text message will accompany it. (Note that BIOS has default text messages built in. We retain the option to include, omit, or change any of these text messages.) Settings printed in Bold are the default values.

A "▶" indicates a submenu. Highlighting such an item and pressing the key will open the list of settings within that submenu.

The BIOS setup utility uses a key-based navigation system called hotkeys. Most of these hotkeys (, , , , keys, etc.) can be used at any time during the setup navigation process.

5.2 Main Page

When you first enter the AMI BIOS setup utility, you will enter the Main setup screen. You can always return to the Main setup screen by selecting the Main tab on the top of the screen. The Main BIOS setup screen is shown below. The following Main menu items are displayed:

Aptio Setup Utility - Copyright (C) 2017 American Megatrends, Inc. Main Advanced Security Boot Save & Exit System Date [Mon 11/27/2017] System Time [19:17:48] Supermicro X11SSN BIOS Version 1.0 Build Date and Time 11/22/2017 11:21:24 Memory Information Total Memory 8192 MB Memory Frequency 2133 MHz Set the Date. Use Tab to switch between Date elements. +: Select Screen ↑↓: Select Item Enter: Select +/-: Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC: Exit Version 2.18.1263. Copyright (C) 2017 American Megatrends, Inc.

System Date/System Time

Use this option to change the system date and time. Highlight System Date or System Time using the arrow keys. Enter new values using the keyboard. Press the key or the arrow keys to move between fields. The date must be entered in Day MM/DD/YYYY format. The time is entered in HH:MM:SS format.

Note: The time is in the 24-hour format. For example, 5:30 P.M. appears as 17:30:00.

Supermicro X11SSN-H-WOHS/-E-WOHS/-L-WOHS

BIOS Version; Build Date and Time

Memory Information

Total Memory: This displays the total size of memory available in the system.

Memory Frequency: This displays the memory speed.

5.3 Advanced Page

Use this tab page to set some boot, power, CPU, SATA, server ME, and input/output settings.

Aptio Setup Utility - Copyright (C) 2017 American Megatrends, Inc. Main Advanced Security Boot Save & Exit ▶ Boot Feature ▶ CPU Configuration ▶ Chipset ▶ SATA Configuration ▶ PCIe/PCI/PnP Configuration ▶ NCT6106D Super IO Configuration ▶ PCH-FW Configuration ▶ Serial Port Console Redirection ▶ NCT6106D HW Monitor ▶ iSCSI Configuration ▶ Intel(R) I210 Gigabit Network Connection - 00:25:90:5E:E9:95 ▶ Intel(R) Ethernet Connection I219-V - 88:88:88:88:87:88 ▶ Trusted Computing System Boot Feature Setting. ++: Select Screen ↑↓: Select Item Enter: Select +/-: Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC: Exit Version 2.18.1253. Copyright (C) 2017 American Megatrends, Inc.

Warning: Take caution when changing the Advanced settings. An incorrect value, a very high DRAM frequency or an incorrect BIOS timing setting may cause the system to malfunction. When this occurs, restore the setting to the manufacture default setting.

▶Boot Feature

Fast Boot

Enable this feature to reduce the time the computer takes to boot up. The computer will boot with a minimal set of required devices. This feature does not have an effect on BBS boot options in the Boot tab. The options are Disabled and Enabled.

Quiet Boot

Use this feature to select the screen display between POST messages or the OEM logo at bootup. Select Disabled to display the POST messages. Select Enabled to display the OEM logo instead of the normal POST messages. The options are Disabled and Enabled.

Bootup Num-Lock

This feature selects the Power-on state for the Numlock key. The options are Off and On.

Wait For "F1" If Error

This feature forces the system to wait until the F1 key is pressed if an error occurs. The options are Disabled and Enabled.

Re-try Boot

If this feature is enabled, the BIOS will automatically reboot the system from a specified boot device after its initial boot failure. The options are Disabled, Legacy Boot, and EFI Boot.

Watch Dog Function

If this feature is enabled, the Watch Dog timer will allow the system to reboot when it is inactive for more than five minutes. The options are Disabled and Enabled.

Power Button Function

This feature controls how the system shuts down when the power button is pressed. Select 4 Seconds Override for the user to power off the system after pressing and holding the power button for 4 seconds or longer. Select Instant Off to instantly power off the system as soon as the user presses the power button. The options are Instant Off and 4 Seconds Override.

AC Loss Policy Depend on

Use this feature to set the power state after a power outage. Select Power Off for the system power to remain off after a power loss. Select Power On for the system power to be turned on after a power loss. Select Last State to allow the system to resume its last power state before a power loss. The options are Stay Off, Power on, and Last State.

EuP Support

EuP, Energy Using Product, is a European energy-saving specification that sets a standard on the maximum total power consumption on electrical products. The options are Disabled and Enabled.

▶CPU Configuration

The following CPU information will display:

• Displays the CPU model
• ID
- Speed
- L1 Data Cache
• L1 Instruction Cache
- L2 Cache
- L3 Cache
- L4 Cache
- VMX
- SMX/TXT

SW Guard Extentions (SGX)

Use this feature to enable or disable Intel Software Guard Extensions (SGX). SGX is a set of CPU instructions that increases software security. The options are Software Controlled, Enabled, and Disabled.

Select Owner EPOCH input type

Use this feature to select an Intel Software Guard Extensions EPOCH mode. Each mode has different values, which can be entered manually. The options are No Change in Owner EPOCHs, Change to New Random Owner EPOCHs, and Manual User Defined Owner EPOCHs.

PRMRR Size

The BIOS must reserve a contiguous region of Processor Reserved Memory (PRM) in the Processor Reserved Memory Range Register (PRMRR). This feature appears if SW Guard Extensions is set to Enabled. The options are INVALID PRMRR, 32MB, 64MB, and 128MB.

Hardware Prefetcher

If this feature is set to Enable, the hardware prefetcher will prefetch streams of data and instructions from the main memory to the Level 2 (L2) cache to improve CPU performance. The options are Disabled and Enabled.

Adjacent Cache Line Prefetch

Select Enabled for the CPU to prefetch both cache lines for 128 bytes as comprised. Select Disable for the CPU to prefetch both cache lines for 64 bytes. The options are Disabled and Enabled.

Intel® (VMX) Virtualization Technology

Select Enabled to use Intel Virtualization Technology to allow one platform to run multiple operating systems and applications in independent partitions, creating multiple virtual systems in one physical computer. The options are Disabled and Enabled. Active Processor Cores

This feature determines how many CPU cores will be activated for each CPU. When All is selected, all cores in the CPU will be activated. Please refer to Intel's website for more information. The options are All and 1.

Hyper-Threading

Select Enabled to support Intel Hyper-threading Technology to enhance CPU performance. The options are Disabled and Enabled.

BIST

Use this feature to enable or disable the built-in self test (BIST) after a reset. The options are Disabled and Enabled.

AES

Select Enable to use the Intel Advanced Encryption Standard (AES) to ensure data security. The options are Disabled and Enabled.

MachineCheck

Use this feature to enable or disable Machine Check. The options are Disabled and Enabled.

MonitorMwait

Select Enabled to enable the Monitor/Mwait instructions. The Monitor instructions monitors a region of memory for writes, and MWait instructions instruct the CPU to stop until the monitored region begins to write. The options are Disabled and Enabled.

Reset AUX Content

Use this feature to reset the TPM Aux content. Txt may not be functional after a reset. The options are yes and no.

FCLK Frequency for Early Power On

FCLK stands for F Clock, which controls the data transfer between the CPU and GPU. The options are Normal (800MHz), 1GHz, and 400MHz.

▶Chipset

Warning: Setting the wrong values in the following sections may cause the system to malfunction.

▶System Agent (SA) Configuration

• SA PCIe Code Version
- VT-d

▶Memory Configuration

• Memory RC Version
• Memory Frequency
• Memory Timings (tCL-tRCD-tRP-tRAS)
- Channel 0 Slot 0

• Size
  • Number of Ranks
• Manufacturer

- Channel 1 Slot 0

Maximum Memory Frequency

Use this feature to select the memory frequency. The options are Auto, 1067, 1333, 1600, 1867, 2133, 2400, 2667, 2933, 3200, 3467, 3733, 4000, and 4133.

▶ Graphics Configuration

LVDS Panel Support

Use this feature to select the supported IGFX graphics device output to the LVDS panel. The options are Disabled and Enabled.

*If LVDS Panel Support is enabled, the five features below are available for configuration:

Panel select

Use this feature to select the panel resolution. The options are Disable, 800x600, 1024x768, 1280x1024, 1366x768, 1680x1050, and 1920x1080.

Panel Channel Type

Use this feature to select the Panel Channel Type. The options are Disabled, Odd Channel, Even Channel, and Both Channel.

Dual LVDS Mode

Use this feature to select a single or dual mode bus for the LVDS display. The options are Disabled, Single LVDS Bus Mode, and Dual LVDS Bus Mode,

Panel Color Depth

Use this feature to select the panel color depth. The options are Disabled, VESA and JEIDA18 bpp, VESA 24 bpp, and JEIDA 24 bpp.

Backlight Brightness

Use this feature to select the backlight brightness for the panel display. Select a range from 1 to 16.

▶LCD Control

Primary IGFX Boot Display

Use this feature to select the type of device that will be activated during POST. The selection will have no effect if an external device is present. The options are VBIOS Default, EFP, LFP, EFP3, EFP2, and EFP4.

LCD Panel Type

Use this feature to select the LCD panel resolution. The options are VBIOS Default, 640x480 LVDS, 800x600 LVDS, 1024x768 LVDS, 1280x1024 LVDS, 1400x1050 LVDS1, 1400x1050 LVDS2, 1600x1200 LVDS, 1280x768 LVDS, 1680x1050 LVDS, 1920x1200 LVDS, 1600x900 LVDS, 1280x800 LVDS, 1280x600 LVDS, 2048x1536 LVDS, and 1366x768 LVDS.

Panel Scaling

Use this feature to select the LCD panel scaling. The options are Auto, Off, and Force Scaling.

Backlight Control

Use this feature to select the type of backlight for the LCD panel. The options are PWM Inverted and PWM Normal.

Active LFP

Use this feature to select the LFP configuration. The options are No eDP and eDP Port-A.

Panel Color Depth

Use this feature to select the LCD panel color depth. The options are 18 Bit and 24 Bit.

▶PCH-IO Configuration

PCH-IO Configuration

• USB Module Version
• USB Controllers
• USB Devices

Legacy USB Support

Select Enabled to support onboard legacy USB devices. Select Auto to disable legacy support if there are no legacy USB devices present. Select Disable to have all USB devices available for EFI applications only. The options are Enabled, Disabled, and Auto.

XHCI Hand-off

This is a work-around solution for operating systems that do not support XHCI (Extensible Host Controller Interface) hand-off. The XHCI ownership change should be claimed by the XHCI driver. The settings are Enabled and Disabled.

USB Mass Storage Driver Support

Select Enabled for USB mass storage device support. The options are Disabled and Enabled.

Port 60/64 Emulation

Select Enabled for I/O port 60h/64h emulation support, which in turn, will provide complete legacy USB keyboard support for the operating systems that do not support legacy USB devices. The options are Disabled and Enabled.

USB hardware delays and time-outs:

USB transfer time-out

Use this feature to set the timeout value for Control, Bulk, and Interrupt transfers. The options are 1 sec, 5 sec, 10 sec, and 20 sec.

Device reset time-out

Use this feature to set the timeout value for a USB mass storage device. The options are 10 sec, 20 sec, 30 sec, and 40 sec.

Device power-up delay

Use this feature to set the maximum time a device takes to report itself to the host controller. The options are Auto and Manual.

Mass Storage Devices:

Sony Storage Media 0100

Enable this feature for mass storage device emulation support. Select Auto to enumerate devices according to their media format. The options are Auto, Floppy, Forced FDD, Hard Disk, and CD-ROM.

xDCI Support

Use this feature to enable or disable the Extensible Device Controller Interface. This feature provides support for USB OTG devices. The options are Disabled and Enabled.

▶SATA Configuration

SATA Controller(s)

Use this feature to enable or disable the onboard SATA controller supported by the SoC. The options are Enabled and Disabled.

*If the feature above is enabled, the following features are available for configuration:

SATA Mode Selection

Use this feature to select the mode for the installed SATA drives. The option is AHCI.

SATA Port 0

This feature displays the information detected on the installed SATA drive on the particular SATA port.

• Model number of drive and capacity
- Software Preserve Support

Port 0

Use this feature to enable or disable the specified SATA port. The options are Disabled and Enabled.

Hot Plug

Set this feature to Enabled for hot plug support, which will allow the user to replace a SATA drive without shutting down the system. The options are Disabled and Enabled.

Spin Up Device

When the value of an edge detect or the value of an image binary (pixel) of a device is from 0 to 1, select Enabled to allow the PCH to start a COMRESET initialization sequence on this device. The options are Disabled and Enabled.

SATA Device Type

Use this item to specify if the SATA port specified by the user should be connected to a Solid State drive or a Hard Disk Drive. The options are Hard Disk Drive and Solid State Drive.

▶PCIe/PCI/PnP Configuration

Option ROM execution

Video

Use this feature to select which firmware type to be loaded for the add-on card in this slot. The options are Do not launch, EFI, and Legacy.

Above 4G MMIO BIOS assignment

Use this feature to enable or disable the above 4GB Memory Mapped IO BIOS assignment. The options are Enabled and Disabled.

PCIe/PCI/PnP Configuration

Mini-PCIe Slot OPROM

Use this feature to select which firmware type to be loaded for the add-on card in this slot. The options are Disabled, Legacy, and EFI.

M.2 SLOT (B KEY) OPROM

Use this feature to select which firmware type to be loaded for the add-on card in this slot. The options are Disabled, Legacy, and EFI.

Onboard LAN1 Controller

Use this feature to enable or disable LAN port 1. The options are Enabled and Disabled.

Onboard LAN2 Controller

Use this feature to enable or disable LAN port 2. The options are Enabled and Disabled.

Onboard LAN Option ROM Type

Use this feature to select which firmware type to be loaded for onboard LAN ports. The options are Legacy and EFI.

Onboard LAN1 Option ROM

Use this feature to select which firmware function to be loaded for LAN port 1 used for system boot. The options are Disabled and PXE.

Onboard LAN2 Option ROM

Use this feature to select which firmware function to be loaded for LAN port 2 used for system boot. The options are Disabled and PXE.

▶NCT6106D Super IO Configuration

NCT6106D Super IO Configuration

Super IO Chip NCT6106D

▶ Serial Port 1 Configuration

Serial Port

Select Enabled to enable the onboard serial port specified by the user. The options are Disabled and Enabled.

Device Settings

This feature displays the base I/O port address and the Interrupt Request address of a serial port specified by the user.

Change Settings

This feature specifies the base I/O port address and the Interrupt Request address of Serial Port 1. Select Auto to allow the BIOS to automatically assign the base I/O and IRQ address to a serial port specified. The options are Auto, (IO=3F8h; IRQ=4), (IO=3F8h; IRQ=3, 4, 5, 6, 7, 9, 10, 11, 12), (IO=2F8h; IRQ=3, 4, 5, 6, 7, 9, 10, 11, 12), (IO=3E8h; IRQ=3, 4, 5, 6, 7, 9, 10, 11, 12), and (IO=2E8h; IRQ=3, 4, 5, 6, 7, 9, 10, 11, 12).

COM1 Port Mode

Use this feature to select the COM port mode. The options are RS232 Mode, RS422 Mode, and RS485 Mode.

▶ Serial Port 2 Configuration

Serial Port

Select Enabled to enable the onboard serial port specified by the user. The options are Disabled and Enabled

Device Settings

This feature displays the base I/O port address and the Interrupt Request address of a serial port specified by the user.

Change Port Settings

This feature specifies the base I/O port address and the Interrupt Request address of Serial Port 2. Select Auto to allow the BIOS to automatically assign the base I/O and IRQ address to a serial port specified. The options are Auto, (IO=2F8h; IRQ=3), (IO=3F8h; IRQ=3, 4, 5, 6, 7, 9, 10, 11, 12), (IO=2F8h; IRQ=3, 4, 5, 6, 7, 9, 10, 11, 12), (IO=3E8h; IRQ=3, 4, 5, 6, 7, 9, 10, 11, 12), and (IO=2E8h; IRQ=3, 4, 5, 6, 7, 9, 10, 11, 12).

COM2 Port Mode

Use this feature to select the COM port mode. The options are RS232 Mode, RS422 Mode, and RS485 Mode.

▶ Serial Port 3 Configuration

Serial Port

Select Enabled to enable the onboard serial port specified by the user. The options are Disabled and Enabled

Device Settings

This feature displays the base I/O port address and the Interrupt Request address of a serial port specified by the user.

Change Settings

This feature specifies the base I/O port address and the Interrupt Request address of Serial Port 3. Select Auto to allow the BIOS to automatically assign the base I/O and IRQ address to a serial port specified. The options are Auto, (IO=3E8h; IRQ=7), (IO=3E8h; IRQ=3, 4, 5, 6, 7, 9, 10, 11, 12), (IO=2E8h; IRQ=3, 4, 5, 6, 7, 9, 10, 11, 12), (IO=2F0h; IRQ=3, 4, 5, 6, 7, 9, 10, 11, 12), and (IO=2E0h; IRQ=3, 4, 5, 6, 7, 9, 10, 11, 12).

▶ Serial Port 4 Configuration

Serial Port

Select Enabled to enable the onboard serial port specified by the user. The options are Disabled and Enabled

Device Settings

This feature displays the base I/O port address and the Interrupt Request address of a serial port specified by the user.

Change Settings

This feature specifies the base I/O port address and the Interrupt Request address of Serial Port 4. Select Auto to allow the BIOS to automatically assign the base I/O and IRQ address to a serial port specified. The options are Auto, (IO=3E8h; IRQ=7), (IO=3E8h; IRQ=3, 4, 5, 6, 7, 9, 10, 11, 12), (IO=2E8h; IRQ=3, 4, 5, 6, 7, 9, 10, 11, 12), (IO=2F0h; IRQ=3, 4, 5, 6, 7, 9, 10, 11, 12), and (IO=2E0h; IRQ=3, 4, 5, 6, 7, 9, 10, 11, 12).

▶PCH-FW Configuration

The following firmware information will display:

• ME Firmware Version
• ME Firmware Mode

• ME Firmware SKU
• ME File System Integrity Value
• ME Firmware Status 1
• ME Firmware Status 2
- NFC Support

▶ Firmware Update Configuration

Me FW Image Re-Flash

Use this feature to update the Management Engine firmware. The options are Disabled and Enabled.

Local FW Update

Use this feature to enable or disable the local firmware update function. When enabled is selected, the firmware can be updated locally. The options are Disabled and Enabled.

▶Serial Port Console Redirection

COM1

Console Redirection

Select Enabled to enable console redirection support for a serial port specified by the user. The options are Enabled and Disabled.

*If the feature above is enabled, the following items are available for configuration:

▶Console Redirection Settings

This feature allows the user to specify how the host computer will exchange data with the client computer, which is the remote computer used by the user.

Terminal Type

This feature allows the user to select the target terminal emulation type for Console Redirection. Select VT100 to use the ASCII Character set. Select VT100+ to add color and function key support. Select ANSI to use the Extended ASCII Character Set. Select VT-UTF8 to use UTF8 encoding to map Unicode characters into one or more bytes. The options are VT100, VT100+, VT-UTF8, and ANSI.

Bits per second

Use this feature to set the transmission speed for a serial port used in Console Redirection. Make sure that the same speed is used in the host computer and the client computer. A lower transmission speed may be required for long and busy lines. The options are 9600, 19200, 38400, 57600, and 115200 (bits per second).

Data Bits

Use this feature to set the data transmission size for Console Redirection. The options are 7 and 8.

Parity

A parity bit can be sent along with regular data bits to detect data transmission errors. Select Even if the parity bit is set to 0, and the number of 1's in data bits is even. Select Odd if the parity bit is set to 0, and the number of 1's in data bits is odd. Select None if you do not want to send a parity bit with your data bits in transmission. Select Mark to add a mark as a parity bit to be sent along with the data bits. Select Space to add a Space as a parity bit to be sent with your data bits. The options are None, Even, Odd, Mark, and Space.

Stop Bits

A stop bit indicates the end of a serial data packet. Select 1 Stop Bit for standard serial data communication. Select 2 Stop Bits if slower devices are used. The options are 1 and 2.

Flow Control

Use this feature to set the flow control for Console Redirection to prevent data loss caused by buffer overflow. Send a "Stop" signal to stop sending data when the receiving buffer is full. Send a "Start" signal to start sending data when the receiving buffer is empty. The options are None and Hardware RTS/CTS.

VT-UTF8 Combo Key Support

Select Enabled to enable VT-UTF8 Combination Key support for ANSI/VT100 terminals. The options are Disabled and Enabled.

Recorder Mode

Select Enabled to capture the data displayed on a terminal and send it as text messages to a remote server. The options are Disabled and Enabled.

Resolution 100x31

Select Enabled for extended-terminal resolution support. The options are Disabled and Enabled.

Putty KeyPad

This feature selects the settings for Function Keys and KeyPad used for Putty, which is a terminal emulator designed for the Windows OS. The options are VT100, LINUX, XTERMR6, SC0, ESCN, and VT400.

COM2

Console Redirection

Select Enabled to use the SOL port for Console Redirection. The options are Disabled and Enabled.

*If the feature above is enabled, the following items are available for configuration:

▶Console Redirection Settings

Use this feature to specify how the host computer will exchange data with the client computer, which is the remote computer used by the user. The options are Enabled and Disabled.

Terminal Type

Use this feature to select the target terminal emulation type for Console Redirection. Select VT100 to use the ASCII Character set. Select VT100+ to add color and function key support. Select ANSI to use the Extended ASCII Character Set. Select VT-UTF8 to use UTF8 encoding to map Unicode characters into one or more bytes. The options are VT100, VT100+, VT-UTF8, and ANSI.

Bits per second

Use this feature to set the transmission speed for a serial port used in Console Redirection. Make sure that the same speed is used in the host computer and the client computer. A lower transmission speed may be required for long and busy lines. The options are 9600, 19200, 38400, 57600, and 115200 (bits per second).

Data Bits

Use this feature to set the data transmission size for Console Redirection. The options are 7 and 8.

Parity

A parity bit can be sent along with regular data bits to detect data transmission errors. Select Even if the parity bit is set to 0, and the number of 1's in data bits is even. Select Odd if the parity bit is set to 0, and the number of 1's in data bits is odd. Select None if you do not want to send a parity bit with your data bits in transmission. Select Mark to add a mark as a parity bit to be sent along with the data bits. Select Space to add a Space as a parity bit to be sent with your data bits. The options are None, Even, Odd, Mark and Space.

Stop Bits

A stop bit indicates the end of a serial data packet. Select 1 Stop Bit for standard serial data communication. Select 2 Stop Bits if slower devices are used. The options are 1 and 2.

Flow Control

Use this feature to set the flow control for Console Redirection to prevent data loss caused by buffer overflow. Send a "Stop" signal to stop sending data when the receiving buffer is full. Send a "Start" signal to start sending data when the receiving buffer is empty. The options are None and Hardware RTS/CTS.

VT-UTF8 Combo Key Support

Select Enabled to enable VT-UTF8 Combination Key support for ANSI/VT100 terminals. The options are Disabled and Enabled.

Recorder Mode

Select Enabled to capture the data displayed on a terminal and send it as text messages to a remote server. The options are Disabled and Enabled.

Resolution 100x31

Select Enabled for extended-terminal resolution support. The options are Disabled and Enabled.

Putty KeyPad

This feature selects Function Keys and KeyPad settings for Putty, which is a terminal emulator designed for the Windows OS. The options are VT100, LINUX, XTERMR6, SCO, ESCN, and VT400.

COM3

Console Redirection

Select Enabled to use the SOL port for Console Redirection. The options are Disabled and Enabled.

*If the feature above is enabled, the following items are available for configuration:

▶Console Redirection Settings

Use this feature to specify how the host computer will exchange data with the client computer, which is the remote computer used by the user. The options are Enabled and Disabled.

Terminal Type

Use this feature to select the target terminal emulation type for Console Redirection. Select VT100 to use the ASCII Character set. Select VT100+ to add color and function key support. Select ANSI to use the Extended ASCII Character Set. Select VT-UTF8 to use UTF8 encoding to map Unicode characters into one or more bytes. The options are VT100, VT100+, VT-UTF8, and ANSI.

Bits per second

Use this feature to set the transmission speed for a serial port used in Console Redirection. Make sure that the same speed is used in the host computer and the client computer. A lower transmission speed may be required for long and busy lines. The options are 9600, 19200, 38400, 57600, and 115200 (bits per second).

Data Bits

Use this feature to set the data transmission size for Console Redirection. The options are 7 and 8.

Parity

A parity bit can be sent along with regular data bits to detect data transmission errors. Select Even if the parity bit is set to 0, and the number of 1's in data bits is even. Select Odd if the parity bit is set to 0, and the number of 1's in data bits is odd. Select None if you do not want to send a parity bit with your data bits in transmission. Select Mark to add a mark as a parity bit to be sent along with the data bits. Select Space to add a Space as a parity bit to be sent with your data bits. The options are None, Even, Odd, Mark and Space.

Stop Bits

A stop bit indicates the end of a serial data packet. Select 1 Stop Bit for standard serial data communication. Select 2 Stop Bits if slower devices are used. The options are 1 and 2.

Flow Control

Use this feature to set the flow control for Console Redirection to prevent data loss caused by buffer overflow. Send a "Stop" signal to stop sending data when the receiving buffer is full. Send a "Start" signal to start sending data when the receiving buffer is empty. The options are None and Hardware RTS/CTS.

VT-UTF8 Combo Key Support

Select Enabled to enable VT-UTF8 Combination Key support for ANSI/VT100 terminals. The options are Disabled and Enabled.

Recorder Mode

Select Enabled to capture the data displayed on a terminal and send it as text messages to a remote server. The options are Disabled and Enabled.

Resolution 100x31

Select Enabled for extended-terminal resolution support. The options are Disabled and Enabled.

Putty KeyPad

Use this feature to select Function Keys and KeyPad settings for Putty, which is a terminal emulator designed for the Windows OS. The options are VT100, LINUX, XTERMR6, SCO, ESCN, and VT400.

COM4

Console Redirection

Select Enabled to use the SOL port for Console Redirection. The options are Disabled and Enabled.

*If the feature above is enabled, the following items are available for configuration:

▶Console Redirection Settings

Use this feature to specify how the host computer will exchange data with the client computer, which is the remote computer used by the user. The options are Enabled and Disabled.

Terminal Type

Use this feature to select the target terminal emulation type for Console Redirection. Select VT100 to use the ASCII Character set. Select VT100+ to add color and function key support. Select ANSI to use the Extended ASCII Character Set. Select VT-UTF8 to use UTF8 encoding to map Unicode characters into one or more bytes. The options are VT100, VT100+, VT-UTF8, and ANSI.

Bits per second

Use this feature to set the transmission speed for a serial port used in Console Redirection. Make sure that the same speed is used in the host computer and the client computer. A lower transmission speed may be required for long and busy lines. The options are 9600, 19200, 38400, 57600, and 115200 (bits per second).

Data Bits

Use this feature to set the data transmission size for Console Redirection. The options are 7 and 8.

Parity

A parity bit can be sent along with regular data bits to detect data transmission errors. Select Even if the parity bit is set to 0, and the number of 1's in data bits is even. Select Odd if the parity bit is set to 0, and the number of 1's in data bits is odd. Select None if you do not want to send a parity bit with your data bits in transmission. Select Mark to add a mark as a parity bit to be sent along with the data bits. Select Space to add a Space as a parity bit to be sent with your data bits. The options are None, Even, Odd, Mark and Space.

Stop Bits

A stop bit indicates the end of a serial data packet. Select 1 Stop Bit for standard serial data communication. Select 2 Stop Bits if slower devices are used. The options are 1 and 2.

Flow Control

Use this feature to set the flow control for Console Redirection to prevent data loss caused by buffer overflow. Send a "Stop" signal to stop sending data when the receiving buffer is full. Send a "Start" signal to start sending data when the receiving buffer is empty. The options are None and Hardware RTS/CTS.

VT-UTF8 Combo Key Support

Select Enabled to enable VT-UTF8 Combination Key support for ANSI/VT100 terminals. The options are Disabled and Enabled.

Recorder Mode

Select Enabled to capture the data displayed on a terminal and send it as text messages to a remote server. The options are Disabled and Enabled.

Resolution 100x31

Select Enabled for extended-terminal resolution support. The options are Disabled and Enabled.

Putty KeyPad

This feature selects Function Keys and KeyPad settings for Putty, which is a terminal emulator designed for the Windows OS. The options are VT100, LINUX, XTERMR6, SCO, ESCN, and VT400.

Legacy Console Redirection

▶Legacy Console Redirection Settings

Redirection COM Port

Use this feature to select the COM port for Console Redirection. The options are COM1, COM2, COM3, and COM4.

Resolution

Use this feature to select the number of rows and columns used in Console Redirection for legacy OS support. The options are 80x24 and 80x25.

Redirect After POST

Use this feature to enable or disable legacy Console Redirection after BIOS POST. When set to Bootloader, legacy Console Redirection is disabled before booting the OS. When set to Always Enable, legacy Console Redirection remains enabled when booting the OS. The options are Always Enable and Bootloader.

Serial Port for Out-of-Band Management/Windows Emergency Management Services (EMS)

The submenu allows the user to configure Console Redirection settings to support Out-of-Band Serial Port management.

Console Redirection

Select Enabled to use a COM port selected by the user for EMS Console Redirection. The options are Enabled and Disabled.

*If the feature above is enabled, the following items are available for configuration:

▶Console Redirection Settings

This feature allows the user to specify how the host computer will exchange data with the client computer, which is the remote computer used by the user.

Out-of-Band Mgmt Port

The feature selects a serial port in a client server to be used by the Microsoft Windows Emergency Management Services (EMS) to communicate with a remote host server. The options are COM1, COM2, COM3, and COM4.

Terminal Type

Use this feature to select the target terminal emulation type for Console Redirection. Select VT100 to use the ASCII character set. Select VT100+ to add color and function key support. Select ANSI to use the extended ASCII character set. Select VT-UTF8 to use UTF8 encoding to map Unicode characters into one or more bytes. The options are VT100, VT100+, VT-UTF8, and ANSI.

Bits Per Second

This feature sets the transmission speed for a serial port used in Console Redirection. Make sure that the same speed is used in the host computer and the client computer. A lower transmission speed may be required for long and busy lines. The options are 9600, 19200, 57600, and 115200 (bits per second).

Flow Control

Use this feature to set the flow control for Console Redirection to prevent data loss caused by buffer overflow. Send a "Stop" signal to stop sending data when the receiving buffer is full. Send a "Start" signal to start sending data when the receiving buffer is empty. The options are None, Hardware RTS/CTS, and Software Xon/Xoff.

▶NCT6106D HW Monitor

The following PC Health Status information will display:

• System temperature
• CPU temperature

Fan Speed Control Mode

Use this feature to select the fan speed mode. The options are Standard and Full Speed.

• VCORE
• VDIMM
  • 12V
• 5V
• AVSB
• 3VSB
  • 3VCC
• VBAT

- CPU Fan Speed

▶iSCSi Configuration

iSCSI Initiator Name

This feature allows the user to enter the unique name of the iSCSI Initiator in IQN format. Once the name of the iSCSI Initiator is entered into the system, configure the proper settings for the following items.

▶ Add an Attempt
▶ Delete Attempts
▶ Change Attempt Order

▶Trusted Computing

The following TPM information is displayed:

TPM2.0 Device Found

Vendor: IFX

Firmware Version: 5.51

Security Device Support

If this feature and the TPM jumper on the motherboard are both set to Enabled, onboard security devices will be enabled for TPM (Trusted Platform Module) support to enhance data integrity and network security. Please reboot the system for a change on this setting to take effect. The options are Disable and Enable.

*If the feature above is enabled, the following items are available for configuration:

The following Platform Configuration Register information is displayed:

Active PCR banks

Available PCR banks

SHA-1 PCR Bank

Use this feature to disable or enable the SHA-1 Platform Configuration Register (PCR) bank for the installed TPM device. The options are Disabled and Enabled.

SHA256 PCR Bank

Use this feature to disable or enable the SHA256 Platform Configuration Register (PCR) bank for the installed TPM device. The options are Disabled and Enabled.

Pending operation

Use this feature to schedule a TPM-related operation to be performed by a security device for system data integrity. Your system will reboot to carry out a pending TPM operation. The options are None and TPM Clear.

Platform Hierarchy

Use this feature to disable or enable platform hierarchy for platform protection. The options are Disabled and Enabled.

Endorsement Hierarchy

Use this feature to disable or enable endorsement hierarchy for privacy control. The options are Disabled and Enabled.

TPM2.0 UEFI Spec Version

Use this feature to select the Trusted Computing Group (TCG) specification version. Version TCG_1_2 is compatible with Windows 8 and 10. Version TCG_2 is compatible with Windows 10 or later. The options are TCG_1_2 and TCG_2.

Physical Presence Spec Version

Use this feature to select the Physical Presence Interface version. This interface uses the ACPI and allows the operating system and BIOS to work together to provide a platform for users to administer the TPM. The options are 1.2 and 1.3.

Device Select

Use this feature to select the TPM version. TPM 1.2 will restrict support to TPM 1.2 devices. TPM 2.0 will restrict support for TPM 2.0 devices. Select Auto to enable support for both versions. The default setting is Auto.

Txt Support

Intel Trusted Execution Technology (Txt) helps protect against software-based attacks and ensures protection, confidentiality, and integrity of data stored or created on the system. The options are Disabled and Enabled.

5.4 Security

Use this menu to configure Security settings.

Aptio Setup Utility - Copyright (C) 2017 American Megatrends, Inc. Main Advanced Security Boot Save & Exit Password Description If ONLY the Administrator's password is set, then this only limits access to Setup and is only asked for when entering Setup. If ONLY the User's password is set, then this is a power on password and must be entered to boot or enter Setup. In Setup the User will have Administrator rights. The password length must be in the following range: Minimum length 3 Maximum length 20 Administrator Password User Password Password Check [Setup] CSM Support [Enabled] ▶ Secure Boot Set Administrator Password ++: Select Screen ↑↓: Select Item Enter: Select +/-: Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC: Exit Version 2.18.1263. Copyright (C) 2017 American Megatrends, Inc.

Administrator Password

Use this feature to set the administrator password which is required to enter the BIOS setup utility. The length of the password should be from 3 to 20 characters long.

User Password

Use this feature to set a user password which is required to log into the system and to enter the BIOS setup utility. The length of the password should be from 3 characters to 20 characters long.

Password Check

Use this feature to determine when a password entry is required. Select Setup to require the password only when entering setup. Select Always to require the password when entering setup and at each bootup. The options are Setup and Always.

CSM Support

Select Enabled to support the EFI Compatibility Support Module (CSM), which provides compatibility support for traditional legacy BIOS for system boot. The options are Enabled and Disabled.

▶Secure Boot

Secure Boot Enable

Select Enable for secure boot support to ensure system security at bootup. The options are Enabled and Disabled.

Secure Boot Mode

This feature allows the user to select the desired secure boot mode for the system. The options are Standard and Custom.

If Secure Boot Mode is set to Custom, Key Management features are available for configuration:

Select Yes to restore all factory keys to the default settings. The options are Yes and No.

▶Key Management

This submenu allows the user to configure the following Key Management settings.

Factory Key Provision

Select Enabled to install the default Secure Boot keys set by the manufacturer. The options are Disabled and Enabled.

*If the feature above is enabled, the following items are available for configuration:

▶ Reset to Setup Mode

Select Yes to delete NVRAM content from all of UEFI Secure Boot key databases. The options are Yes and No.

Select Yes to restore Secure Boot keys to factory default. The options are Yes and No.

▶ Export Secure Boot variables

Select Yes to copy NVRAM content to a file in the root folder. The options are Yes and No.

▶Enroll Efi Image

This feature allows the image to run in Secure Boot mode.

Device Guard Ready

▶Remove 'UEFI CA' from DB

Select Yes to remove UEFI CA from the list of Microsoft Certified DB database. The options are Yes and No.

Select Yes to restore DB variables to facotry default. The options are Yes and No.

Secure Boot variable | Size | Keys | Key Source

▶ Platform Key (PK)

Use this feature to configure the setting for platform keys.

Details

Select this feature to view PK information.

Export

Select this feature to export the PK from a file system.

Update

Select Yes to load the PK from factory default or No to load from a file or external media.

Delete

Select ok to remove the PK. Reset the system for it to enter Setup/Audit Mode.

▶Key Exchange Keys

Use this feature to configure the setting for key exchange keys.

Details

Select this feature to view KEK information.

Export

Select this feature to export the KEK from a file system.

Update

Select Yes to load the KEK from factory default or No to load from a file or external media.

Append

Select Yes to load the KEK from factory default or No to load from a file or external media.

Delete

Select Yes to delete the variable or No to delete a certificate from the key database.

▶ Authorized Signatures

Use this feature to configure the setting for db keys.

Details

Select this feature to view authorized signatures information.

Export

Select this feature to export the db from a file system.

Update

Select Yes to load the db from factory default or No to load from a file or external media.

Append

Select Yes to load the db from factory default or No to load from a file or external media.

Delete

Select Yes to delete the variable or No to delete a certificate from the key database.

▶Forbidden Signatures

Use this feature to configure the setting for dbx keys.

Details

Select this feature to view forbidden signatures information.

Export

Select this feature to export the dbx from a file system.

Update

Select Yes to load the dbx from factory default or No to load from a file or external media.

Append

Select Yes to load the dbx from factory default or No to load from a file or external media.

Delete

Select Yes to delete the variable or No to delete a certificate from the key database.

▶ Authorized TimeStamps

Use this feature to configure the setting for dbt keys.

Details

Select this feature to view authorized time stamp information.

Export

Select this feature to export the dbt from a file system.

Update

Select Yes to load the dbt from factory default or No to load from a file or external media.

Append

Select Yes to load the dbt from factory default or No to load from a file or external media.

Delete

Select Yes to delete the variable or No to delete a certificate from the key database.

▶OsRecovery Signature

Use this feature to configure the setting for dbr keys.

Details

Select this feature to view authorized time stamp information.

Export

Select this feature to export the dbr from a file system.

Update

Select Yes to load the dbr from factory default or No to load from a file or external media.

Append

Select Yes to load the dbr from factory default or No to load from a file or external media.

Delete

Select Yes to delete the variable or No to delete a certificate from the key database.

5.5 Boot

Use this menu to configure Boot settings:

Aptio Setup Utility - Copyright (C) 2017 American Megatrends, Inc. Main Advanced Security Boot Save & Exit Boot Configuration New Boot Option Policy [Default] Fast Boot [Disabled] Boot mode select [DUAL] FIXED BOOT ORDER Priorities Boot Option #1 [UEFI AP:UEFI: Built-in EFI Shell] Boot Option #2 [CD/DVD] Boot Option #3 [USB Hard Disk] Boot Option #4 [USB CD/DVD] Boot Option #5 [Hard Disk] Boot Option #6 [USB Floppy] Boot Option #7 [USB Lan] Boot Option #8 [Network:IBA GE Slot 0200 v1404] Boot Option #9 [UEFI Hard Disk] Boot Option #10 [UEFI CD/DVD] Boot Option #11 [UEFI USB Hard Disk] Boot Option #12 [UEFI USB CD/DVD] Boot Option #13 [UEFI USB Key] Boot Option #14 [UEFI USB Floppy] Boot Option #15 [UEFI USB Lan] Controls the placement of newly detected UEFI boot options +: Select Screen ↑↓: Select Item Enter: Select +/-: Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC: Exit Version 2.18.1263. Copyright (C) 2017 American Megatrends, Inc.

Boot Configuration

New Boot Option Policy

Use this feature to select the boot order for a newly detected device. The options are Default, Place First, and Place Last.

Fast Boot

Enable this feature to reduce the time the computer takes to boot up. The computer will boot with a minimal set of required devices. This feature does not have an effect on BBS boot options in the Boot tab. The options are Disabled and Enabled.

*If the feature above is enabled, the next five features are available for configuration:

SATA Support

If Last Boot HDD Only is selected, only hard disk drives will be available during the boot up POST. If All Sata Devices is selected, all SATA devices will be available during the boot up POST. The options are Last Boot HDD Only and All Sata Devices.

VGA Support

Sue this feature to select which VGA drivers are installed during POST. Select Auto to install Legacy OpRom. The options are Auto and EFI Driver.

USB Support

Select Disabled for all USB devices to be unavailable until after the operating system boots, Parital Initial for all USB devices to be unavailable before the operating system boots, and Full Initial for all USB ports to be enabled during the POST. The options are Disabled, Full Initial, and Partial Initial.

PS2 Device Support

Use this feature to disable or enable PS2 device support during boot up. The options are Disabled and Enabled.

Network Stack Driver Support

Use this feature to disable or enable network stack driver support during boot up. The options are Disabled and Enabled.

Redirection Support

Use this feature to disable or enable redirection support. The options are Disabled and Enabled.

Boot mode select

Use this feature to select the boot mode for bootable devices in the system. The options are LEGACY, UEFI, and DUAL.

Fixed Boot Order Priorities

This feature prioritizes the order of bootable devices that the system can boot from. Press on each entry from top to bottom to select devices.

• Boot Option #1
• Boot Option #2
• Boot Option #3
• Boot Option #4
• Boot Option #5
• Boot Option #6
• Boot Option #7
• Boot Option #8
• Boot Option #9

• Boot Option #10

• Boot Option #11

• Boot Option #12
• Boot Option #13
• Boot Option #14
• Boot Option #15

▶ Add New Driver Option

Use this feature to add a new EFI driver option from the driver order.

▶ Delete Driver Option

Use this feature to remove an EFI driver option from the driver order.

▶UEFI Application Boot Priorities

This feature allows the user to specify which UEFI application devices are boot devices.

- Boot Option #1

▶UEFI USB Key Drive BBS Priorities

This feature allows the user to specify which UEFI USB key drive devices are boot devices.

- Boot Option #1

▶USB Key Drive BBS Priorities

This feature allows the user to specify which USB key drive devices are boot devices.

- Boot Option #1

▶NETWORK Drive BBS Priorities

This feature allows the user to specify which network drives are boot devices.

• Boot Option #1
• Boot Option #2

5.6 Save & Exit

Select the Exit tab from the BIOS setup utility screen to enter the Exit BIOS Setup screen.

Aptio Setup Utility - Copyright (C) 2017 American Megatrends, Inc. Main Advanced Security Boot Save & Exit Save Options Discard Changes and Exit Save Changes and Reset Save Changes Discard Changes Default Options Restore Defaults Save as User Defaults Restore User Defaults Boot Override UEFI: Built-In EFI Shell IBA GE Slot 0200 v1404 IBA CL Slot 00FE v0110 UEFI: PXE IP4 Intel(R) I210 Gigabit Network Connection UEFI: PXE IP6 Intel(R) I210 Gigabit Network Connection UEFI: PXE IP4 Intel(R) Ethernet Connection I219-V UEFI: PXE IP6 Intel(R) Ethernet Connection I219-V Launch EFI Shell from filesystem device Exit system setup without saving any changes. ++: Select Screen ↑↓: Select Item Enter: Select +/-: Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC: Exit Version 2.18.1263. Copyright (C) 2017 American Megatrends, Inc.

Save Options

Discard Changes and Exit

Select this feature to exit the BIOS without saving any changes.

Save Changes and Reset

When you have completed the system configuration changes, select this option to save all changes made and reset the system.

Save Changes

When you have completed the system configuration changes, select this option to save all changes made. This will not reset (reboot) the system.

Discard Changes

Select this feature and press to discard all the changes and return to the AMI BIOS Utility Program.

Default Options

Restore Defaults

To set this feature, select Restore Defaults from the Exit menu and press . These are factory settings designed for maximum system performance but not for maximum stability.

Save as User Defaults

To set this feature, select Save as User Defaults from the Exit menu and press . This enables the user to save any changes to the BIOS setup for future use.

To set this feature, select Restore User Defaults from the Exit menu and press . Use this feature to retrieve user-defined settings that were saved previously.

Boot Override

Sony Storage Media 0100

IBA GE Slot 0200 v1404

IBA CL Slot 00FE v0110

UEFI: Sony Storage Media 0100, Partition 1

UEFI: Built-in EFI Shell

Launch EFI Shell from filesystem device

Appendix A

BIOS Error Codes

A.1 BIOS Error Beep (POST) Codes

During the POST (Power-On Self-Test) routines, which are performed each time the system is powered on, errors may occur.

Non-fatal errors are those which, in most cases, allow the system to continue the boot-up process. The error messages normally appear on the screen.

Fatal errors are those which will not allow the system to continue the boot-up procedure. If a fatal error occurs, you should consult with your system manufacturer for possible repairs.

These fatal errors are usually communicated through a series of audible beeps. The table below lists some common errors and their corresponding beep codes encountered by users.

BIOS Beep (POST) Codes
Beep Code Error	Message Description
1 beep Refresh Circuits have been reset (Ready to power up)
5 short, 1 long Memory error No memory detected in system
5 long, 2 short Display memory read/write error Video adapter missing or with faulty memory
1 long continuous System OH System overheat condition

A.2 Additional BIOS POST Codes

The AMI BIOS supplies additional checkpoint codes, which are documented online at http://www.supermicro.com/support/manuals/ ("AMI BIOS POST Codes User's Guide").

When BIOS performs the Power-On Self-Test, it writes checkpoint codes to I/O port 0080h. If the computer cannot complete the boot process, a diagnostic card can be attached to the computer to read I/O port 0080h (Supermicro p/n AOC-LPC80-20).

For information on AMI updates, please refer to http://www.ami.com/products/.

Appendix B

Standardized Warning Statements for DC Systems

B.1 About Standardized Warning Statements

The following statements are industry standard warnings, provided to warn the user of situations which have the potential for bodily injury. Should you have questions or experience difficulty, contact Supermicro's Technical Support department for assistance. Only certified technicians should attempt to install or configure components.

Read this appendix in its entirety before installing or configuring components in the Supermicro chassis.

These warnings may also be found on our website at http://www.supermicro.com/about/policies/safety_information.cfm.

Warning Definition

Warning! This warning symbol means danger. You are in a situation that could cause bodily injury. Before you work on any equipment, be aware of the hazards involved with electrical circuitry and be familiar with standard practices for preventing accidents.

警告の定義

この警告サインは危険を意味します。

Installation Instructions

Warning! Read the installation instructions before connecting the system to the power source.

設置手順書

Warning! This product relies on the building's installation for short-circuit (overcurrent) protection. Ensure that the protective device is rated not greater than: 60VDC, 20A.

サーキット・ブレーカー

Power Disconnection Warning

Warning! The system must be disconnected from all sources of power and the power cord removed from the power supply module(s) before accessing the chassis interior to install or remove system components.

電源切断の警告

Equipment Installation

Warning! Only trained and qualified personnel should be allowed to install, replace, or service this equipment.

機器の設置

Warning! This unit is intended for installation in restricted access areas. A restricted access area can be accessed only through the use of a special tool, lock and key, or other means of security. (This warning does not apply to workstations).

アクセス制限区域

Warning! There is the danger of explosion if the battery is replaced incorrectly. Replace the battery only with the same or equivalent type recommended by the manufacturer. Dispose of used batteries according to the manufacturer's instructions

電池の取り扱い

Redundant Power Supplies

Warning! This unit might have more than one power supply connection. All connections must be removed to de-energize the unit.

冗長電源裝置

Warning! Hazardous voltage or energy is present on the backplane when the system is operating. Use caution when servicing.

バックプレーンの電圧

Comply with Local and National Electrical Codes

Warning! Installation of the equipment must comply with local and national electrical codes.

地方および国の電気規格に準拠

Warning! Ultimate disposal of this product should be handled according to all national laws and regulations.

製品の廃棄

Warning! Hazardous moving parts. Keep away from moving fan blades. The fans might still be turning when you remove the fan assembly from the chassis. Keep fingers, screwdrivers, and other objects away from the openings in the fan assembly's housing.

ファン・ホットスワップの警告

Warning! When stranded wiring is required, use approved wiring terminations, such as closedloop or spade-type with upturned lugs. These terminations should be the appropriate size for the wires and should clamp both the insulation and conductor.

警告

DC Power Disconnection

Warning! Before performing any of the following procedures, ensure that power is removed from the DC circuit.

警告

Hazardous Voltage or Energy Present on DC Power Terminals

Warning! Hazardous voltage or energy may be present on DC power terminals. Always replace cover when terminals are not in service. Be sure uninsulated conductors are not accessible when cover is in place.

警告

System Specifications

Processors

E100-9S: 7th Generation Intel® Core i7-7600U Processor (System on Chip) Socket FCBGA 1356

E100-9S-E: 7th Generation Intel® Core i5-7300U Processor (System on Chip) Socket FCBGA 1356

E100-9S-L: 7th Generation Intel ^® Core i3-7100U Processor (System on Chip) Socket FCBGA 1356

Note: Please refer to the motherboard specifications pages on our website for updates to supported processors.

BIOS

AMI® UEFI BIOS

Memory

Supports up to 32 GB non-ECC SODIMM; Memory Type DDR4 2133 MHz; 2 DIMM slots

Hard Drives

Supports one M.2 SATA SSD B-Key 2280

Expansion Slots

One full-size Mini-PCIe slot

One M.2 B-key 2280 (SATA/PCI-E or WWAN/GNSS) slot

Motherboard

X11SSN-H-WOHS/-E-WOHS/-L-WOHS

Chassis

SCE-101-01 (3.5" SBC), (WxHxD) 7.68" x 5.94" x 1.73" (195 x 44 x 151 mm)

Power Supply

Lockable 60W Power Adapter for 12V DC

Operating Environment

Operating Temperature: 0°C to 50°C (32°F to 122°F)

Non-operating Temperature: -40°C to 70°C (-40°F to 158°F)

Operating Relative Humidity: 8% to 90% (non-condensing)

Non-operating Relative Humidity: 5% to 95% (non-condensing)

Regulatory Compliance

Electromagnetic Emissions: FCC Class B, EN 55032 Class B, EN 61000-3-2/3-3, CISPR 32/22 Class B

Electromagnetic Immunity: EN 55024/CISPR 24, (EN 61000-4-2, EN 61000-4-3, EN 61000-4-4, EN 61000-4-5, EN 61000-4-6, EN 61000-4-8, EN 61000-4-11)

Safety: CSA/EN/IEC/UL 60950-1 Compliant, UL or CSA Listed (USA and Canada), CE Marking (Europe),

The Bureau of Standards, Metrology and Inspection (BSMI)

Perchlorate Warning

California Best Management Practices Regulations for Perchlorate Materials: This Perchlorate warning applies only to products containing CR (Manganese Dioxide) Lithium coin cells. "Perchlorate Material-special handling may apply. See www.dtsc.ca.gov/hazardouswaste/perchlorate"

Appendix D

Traditional Chinese Version Safety Warnings

Additional Traditional Chinese Version warning statements are included here in this appendix.

安全警告(注意這些警告標誌)

Table C-1. Declaration of the Presence Condition of the Restricted Substances
Marking (限用物質含有情況標示聲明書
喂物質含有情況標示聲明書
Declaration of the Presence Condition of the Restricted Substances Marking

設備名稱:伺服器, 型號(型式):連*於 E100-9S/-9S-E/-9S-L 及其所有系列機種 Type designationEquipment name: Server (Type): E100-9S/-9S-E/-9S-L and all its series models
單元Unit	埋*物質及其化學符號Restricted Substances and its Chemical Symbols
	鉤Lead(Pb)	天Mercury(Hg)	銘Cadmium(Cd)	六貨鉻HexavalentChromium(Cr+6)	多溴聯苯PolybrominatedBiphenyls(PBB)	多溴二苯醚PolybrominatedDiphenylEthers(PBDE)
機數Chassis	○	○	○	○	○	○
機數圧磊Chassis Fan	—	○	○	○	○	○
線材Cable	○	○	○	○	○	○
主機板Motherboard	—	○	○	○	○	○
電源供應器Power Supply	—	○	○	○	○	○
電源筆板PDB	—	○	○	○	○	○
附註+Add-on Card	—	○	○	○	○	○
備考1. “超出0.1 wt %”又“超出0.01 wt %”係指 ^※ 物質之百分比含量超出百分比含量基準值。Note 1: “Exceeding 0.1 wt %” and “exceeding 0.01 wt %” indicate that the percentage content of the restricted substance exceeds the reference percentage value of presence condition.備考2. “○”係指該項 ^※ 物質之百分比含量大超出百分比含量基準值。Note 2: “○” indicates that the percentage content of the restricted substance does not exceed the percentage of reference value of presence.備考3. “—”係指該項 ^※ 物質為排除項目。Note 3: The “—” indicates that the restricted substance corresponds to the exemption.

Appendix E

UEFI BIOS Recovery

Warning: Do not upgrade the BIOS unless your system has a BIOS-related issue. Flashing the wrong BIOS can cause irreparable damage to the system. In no event shall Supermicro be liable for direct, indirect, special, incidental, or consequential damages arising from a BIOS update. If you need to update the BIOS, do not shut down or reset the system while the BIOS is updating to avoid possible boot failure.

D.1 Overview

The Unified Extensible Firmware Interface (UEFI) provides a software-based interface between the operating system and the platform firmware in the pre-boot environment. The UEFI specification supports an architecture-independent mechanism that will allow the UEFI OS loader stored in an add-on card to boot the system. The UEFI offers clean, hands-off management to a computer during system boot.

D.2 Recovering the UEFI BIOS Image

A UEFI BIOS flash chip consists of a recovery BIOS block and a main BIOS block (a main BIOS image). The boot block contains critical BIOS codes, including memory detection and recovery codes for the user to flash a new BIOS image if the original main BIOS image is corrupted. When the system power is first turned on, the boot block codes execute first. Once this process is completed, the main BIOS code will continue with system initialization and the remaining POST (Power-On Self-Test) routines.

Note 1: Follow the BIOS recovery instructions below for BIOS recovery when the main BIOS boot crashes.

Note 2: When the BIOS boot block crashes, you will need to follow the procedures to make a Returned Merchandise Authorization (RMA) request. (For a RMA request, please see section 3.5 for more information). Also, you may use the Supermicro Update Manager (SUM) Out-of-Band (OOB) (https://www.supermicro.com.tw/products/nfo/SMS_SUM.cfm) to reflash the BIOS.

D.3 Recovering the BIOS Block with a USB Device

This feature allows the user to recover a BIOS image using a USB-attached device without additional utilities used. A USB flash device such as a USB Flash Drive, or a USB CD/DVD ROM/RW device can be used for this purpose. However, a USB Hard Disk drive cannot be used for BIOS recovery at this time.

The file system supported by UEFI is FAT (including FAT12, FAT16, and FAT32) which is installed on a bootable or non-bootable USB-attached device. However, the BIOS might need several minutes to locate the SUPER.ROM file if the media size becomes too large due to the huge volumes of folders and files stored in the device.

To perform UEFI BIOS recovery using a USB-attached device, follow the instructions below.

1. Using a different machine, copy the "Super.ROM" binary image file into the disc Root "\" directory of a USB device or a writable CD/DVD.

Note: If you cannot locate the "Super.ROM" file in your driver disk, visit our website at www.supermicro.com to download the BIOS image into a USB flash device and rename it "Super.ROM" for BIOS recovery use.

1. Insert the USB device that contains the new BIOS image ("Super.ROM") into your USB drive and power on the system
2. While powering on the system, keep pressing and simultaneously on your keyboard until the following screen (or a screen similar to the one below) displays.

Warning: Please stop pressing the and keys immediately when you see the screen (or a similar screen) below; otherwise, it will trigger a system reboot.

SUSP MMC IP:18.132.161.98 System Initializing...

Note: On the other hand, if the following screen displays, please load the "Super.ROM" file to the root folder and connect this folder to the system. (You can do so by inserting a USB device that contains the new "Super.ROM" image to your machine for BIOS recovery.)

Moto Setup Utility = Copyright (C) 2017 American Regentrends, Inc. Main Advanced Event logs IPDI Recovery Security Host Save & Exit ROM Image is not loaded ROM Image update denied +: Select Screen F4: Select Item Enter: Select +/-: Change Opt. F1: General help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC: Exit Version 5.19.1266. Copyright DC 2017 American MegaTrands, Inc.

1. After locating the new BIOS binary image, the system will enter the BIOS Recovery menu as shown below.

Ratio Setup Utility - Copyright (C) 2017 American Megatrends, Inc. Main Advanced Event Log: IPM Recovery Security Boot Save & Exit Please select blocks you want to update Reset NVRAM [Enabled] Boot Block Update [Enabled] ► Proceed with flash update Set this option to reset NVRAM to default values +: Select Screen T4: Select Item Enter: Select +/-: Change Opt F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC: Exit Version 2.19.1236. Copyright (C) 2017 American Megatrends, Inc.

Note: At this point, you may decide if you want to start the BIOS recovery. If you decide to proceed with BIOS recovery, follow the procedures below.

1. When the screen as shown above displays, use the arrow keys to select the item "Proceed with flash update" and press the key. You will see the BIOS recovery progress as shown in the screen below.

Aptio Setup Utility - Copyright (C) 2017 American Megatrends, Inc. Recovery WARNING! System firmware is being updated. Keyboard is locked. DO NOT TURN THE POWER OFF !!! Once firmware update is completed press any key to reboot the system Program new data Write new boot block... 17% +: Select Screen T4: Select Item Enter: Select +/-: Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC: Exit Version 2.19.1256, Copyright (C) 2017 American Megatrends, Inc.

Note: Do not interrupt the BIOS flashing process until it has completed.

Aotic Setup Utility - Copyright (C) 2017 American Megatrends, Inc. Recovery WARNING! System firmware is being updated. Keyboard is locked. DO NOT TURN THE POWER OFF !!! Once firmware update is completed press any key to reboot the system Flash update Flash update completed. Press any key to reset the system +: Select Screen 1: Select Item Enter: Select +/-: Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC: Exit Version 2.19.1265. Copyright (C) 2017 American Megatrends, Inc.

1. After the BIOS recovery process is completed, press any key to reboot the system.
2. Using a different system, extract the BIOS package into a USB flash drive.

Auto Setup Utility - Copyright (C) 2017 American Megatrends, Inc. Help Advanced Event Logs IPMI Security Boot Save & Exit Boot Configuration Boot mode select [DUAL] LEGWDY to EFI support [Disabled] FIXED BOOT ORDER Priorities Boot Option #1 [UEFI EP/UEFI BUL...] Boot Option #2 [CD/DVD] Boot Option #3 [USB Hard Disk] Boot Option #4 [USB CD/DVD] Boot Option #5 [USB Key:SanDisk] Boot Option #6 [USB Floppy] Boot Option #7 [USB Lan] Boot Option #8 [Network:IBA GE SI...] Boot Option #9 [UEFI Hard Disk] Boot Option #10 [UEFI CD/DVD] Boot Option #11 [UEFI USB Hard Disk] Boot Option #12 [UEFI USD CD/DVD] Boot Option #13 [UEFI USB Key:UEFI...] Boot Option #14 [UEFI USD Floppy] Boot Option #15 [UEFI USB Lan] Boot Option #16 [UEFI Network] Boot Option #17 [Hard Disk] ► Add New Boot Option Sets the system boot order ←: Select Screen T4: Select Item Enter: Select +/-: Change Opt. F1: General help F2: Previous Values FG: Optimized Defaults F4: Save a Exit ESC: Exit Version 2.19.1266. Copyright (C) 2017 American Megatrends, Inc.

1. Press continuously during system boot to enter the BIOS setup utility. From the top of the tool bar, click on Boot and press to enter the submenu. From the submenu list, select Boot Option #1 as shown below. Then, boot Option #1 to [UEFI AP:UEFI: Built-in EFI Shell]. Press to save the settings and exit the BIOS setup utility.

2. When the UEFI Shell prompt appears, type fs# to change the device directory path. Go to the directory that contains the BIOS package you extracted earlier from Step 7. Enter flash.nsh BIOSname.### at the prompt to start the BIOS update process.

UIFI Interactive Shell v2.1 E0K II UIFI v2.50 (American Megatrends, 0x0005000S) Mapping table F00: Alias(s):H0e0b:BL11 PcI:Rout(lx0).PcI(lx14,0xC)/USB(0x11,0xC)/HD(1,HBR,0xD7901072,0xE08,0x1 GND392 BL00: Alias(s): PcI:Rout(lx0).PcI(lx14,0xC)/USB(0x11,0xC) Press FSS in 1 seconds to strip startup.shn or any other key to continue. Shell v2.1 FSO:\CD PFDOS FSO:\VARDOS\CD S&PME2_03162017 FSO:\VARDBS\S&PME2_03562017\Flash.shx_X110PU7.514

Note: Do not interrupt this process until the BIOS flashing is complete.

[Access Cwos Port Ex] [Read] Index 0x51: 0x18 Done. * Program BIOS and ME (including FDT) regions... * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * CRUD = 50652 Reading flash ......... done - ME Data Size checking . sk - FFS checkups ......... dk - Check RootLayout ......... ok Erasing Boot Block ......... done Updating Boot Block ......... done Verifying Boot Block ......... done Erasing Main Block ......... 0x00132009 (OK)

1. The screen above indicates that the BIOS update process is completed. When you see the screen above, unplug the AC power cable from the power supply, clear CMOS, and plug the AC power cable in the power supply again to power on the system.

Verifying NCA Block ......... done - Update success for REN - Update success for IE - - Successful Update Recovery Loader to OPRs!! - Successful Update MFSB1((-) - Successful Update FTPR((-) - Successful Update HFS, J#61 and J#82((-) - Successful Update FLOG and UTOK((-) - ME Entire Image update success 11 WARNING : System must power-off to have the changes take effect! Having F501:\AFUDOS\NATMIE2_00162017\#xt\tx64.efi -> F501:\AFUDOS\NATMIE2_03162017\f of SMC - [OK] Having F501:\AFUDOS\NATMIE2_00162017\afuefb\x64.efi -> F501:\AFUDOS\NATMIE2_0316201 7\tafeefi.sMC - [OK] ****************************************************************************************** * + Please Ignore this 'Shell: Cannot read from file - Device Error' + warning message due to it does not impact flashing process. * ****************************************************************************************** Deleting ' Delete successful. F500(-) =

1. Press continuously to enter the BIOS setup utility.
2. Press to load the default settings.
3. After loading the default settings, press to save the settings and exit the BIOS setup utility.