MSP-DCCKTP445 - Audio Visual Accessory Chief - Free user manual and instructions

USER MANUAL MSP-DCCKTP445 Chief

INSTALLATION INSTRUCTIONS

Technical line drawing of a mechanical assembly with no visible text or symbols

MSP-DCCKTP225

Technical line drawing of two curved mechanical components mounted on a stand (no text or symbols)

MSP-DCCKTP445

Technical line drawing of a mechanical lever assembly with mounting base (no text or symbols)

MSP-DCCKTP225U

Technical line drawing of two curved mechanical components mounted on a stand (no text or symbols)

MSP-DCCKTP445U

Horizontal Table Stands

DISCLAIMER

Milestone AV Technologies and its affiliated corporations and subsidiaries (collectively "Milestone"), intend to make this manual accurate and complete. However, Milestone makes no claim that the information contained herein covers all details, conditions or variations, nor does it provide for every possible contingency in connection with the installation or use of this product. The information contained in this document is subject to change without notice or obligation of any kind. Milestone makes no representation of warranty, expressed or implied, regarding the information contained herein. Milestone assumes no responsibility for accuracy, completeness or sufficiency of the information contained in this document.

Chief® is a registered trademark of Milestone AV Technologies. All rights reserved.

IMPORTANT SAFETY INSTRUCTIONS

WARNING: A WARNING alerts you to the possibility of serious injury or death if you do not follow the instructions.

CAUTION: A CAUTION alerts you to the possibility of damage or destruction of equipment if you do not follow the corresponding instructions.

WARNING: Failure to read, thoroughly understand, and follow all instructions can result in serious personal injury, damage to equipment, or voiding of factory warranty! It is the installer's responsibility to make sure all components are properly assembled and installed using the instructions provided.

WARNING: Failure to provide adequate structural strength for this component can result in serious personal injury or damage to equipment! It is the installer's responsibility to make sure the structure to which this component is attached can support five times the combined weight of all equipment. Reinforce the structure as required before installing the component.

WARNING: Exceeding the weight capacity can result in serious personal injury or damage to equipment! It is the installer's responsibility to make sure the combined weight of all components attached to the MSP-DCCKTP SERIES mounts does not exceed 35 lbs (15.87 kg) per display for the single array models (MSP-DCCKTP225/U) or 20 lbs (9.07 kg) per display for the dual array models (MSP-DCCKTP445/U).

WARNING: Use this mounting system only for its intended use as described in these instructions. Do not use attachments not recommended by the manufacturer.

WARNING: Never operate this mounting system if it is damaged. Return the mounting system to a service center for examination and repair.

WARNING: Do not use this product outdoors.

--SAVE THESE INSTRUCTIONS--

DIMENSIONS

MSP-DCCKTP225

MSP-DCCKTP445

IF SAME SIZE DISPLAY IS USED FOR BOTH, MAXIMUM SCREEN WIDTH OF 30.0"

DIMENSIONS (CONTINUED)

MSP-KTP445U

IF SAME SIZE DISPLAY IS USED FOR BOTH, MAXIMUM SCREEN WIDTH OF 30.0"

LEGEND

	Tighten Fastener		Pencil Mark
	Apretar elemento de fijación		Marcar con lápiz
	Befestigungsteil festziehen		Stiftmarkierung
	Apertar fixador		Marcar com lápis
	Serrare il fissaggio		Segno a matita
	Bevestiging vastdraaien		Potloodmerkteken
	Serrez les fixations		Marquage au crayon
	Loosen Fastener		Drill Hole
	Aflojar elemento de fijación		Perforar
	Befestigungsteil lösen		Bohrloch
	Desapertar fixador		Fazer furo
	Allentare il fissaggio		Praticare un foro
	Bevestiging losdraaien		Gat boren
	Desserrez les fixations		Percez un trou
	Phillips Screwdriver		Adjust
	Destornillador Phillips		Ajustar
	Kreuzschlitzschraubendreher		Einstellen
	Chave de fendas Phillips		Ajustar
	Cacciavite a stella		Regolare
	Kruiskopschroevendraaier		Afstellen
	Tournevis à pointe cruciforme		Ajuster
	Open-Ended Wrench		Remove
	Llave de boca		Quitar
	Gabelschlüssel		Entfernen
	Chave de bocas		Remover
	Chiave a punte aperte		Rimuovere
	Steeksleutel		Verwijderen
	Clé à fourche		Retirez
	By Hand		Optional
	A mano		Opcional
	Von Hand		Optional
	Com a mão		Opcional
	A mano		Opzionale
	Met de hand		Optie
	À la main		En option
	Hex-Head Wrench		Security Wrench
	Llave de cabeza hexagonal		Llave de seguridad
	Sechskantschlüssel		Sicherheitsschlüssel
	Chave de cabeça sextavada		Chave de segurança
	Chiave esagonale		Chiave di sicurezza
	Zeskantsleutel		Veiligheidssleutel
	Clé à tête hexagonale		Clé de sécurité

TOOLS REQUIRED FOR INSTALLATION

3/4" (19 mm) #2 7/32" (included) 5/32" (included)

PARTS

Quantities listed - (225/445 models) A (1/2) [Array assembly] B (1/2) [Array clamp] C (2/4) 1/4-20 x 3/4" D (2/4) 1/4" E (1/1) 7/32" F (1/1) 5/32" G (1/1) 3/8-16 x 1" H (8/16) M4x12mm J (8/16) M4x20mm K (8/16) M4x30mm L (8/16) 3/8" M (8/16) 3/4" N (1/1) [Base] P (1/1) [Pole] Q (1/1) [Pipe cap] R (1/1) [Cable management cover]

Assembly And Installation

To assemble array to pole

1. Assemble pole (P) to base (N) using one 3/8-16 x 1" flat head cap screw (G). (See Figure 1)

(P) (E) (G) (N)

Figure 1

1. Assemble pole clamp back (B) to array assembly (A) using two 1/4" washers (D) and two 1/4-20 x 3/4" button head cap screws (C) using a 5/32" hex key (F). (See Figure 2)
2. Secure array clamp (B) to array assembly (A) and pole by tightening two 1/4-20 x 3/4" button head cap screws (C). (See Figure 2)

(A) (P) (B) (D) x 2 (C) x 2 3

Figure 2

1. Repeat Steps 1-3 for dual array models.
2. Add pipe cap (Q) to top of pole (P).

Display Installation - Non-interface Models

Attach Centris Head to Flush Mount Display

CAUTION: If display uses a screw size other than those included in the kit, DO NOT use the screws provided. Using the wrong screws could result in damage to your monitor.

1. Install two M4 x 12mm Phillips pan head screws (H) into two upper mounting holes in display back. (See Figure 3)
   NOTE: DO NOT fully tighten at this time.
2. Hang display on Centris head. (See Figure 4)
3. Install bottom two M4 x 12mm Phillips pan head screws (H) through Centris head mounting holes and into lower mounting holes in display back.
4. Tighten ALL four M4 x 12mm Phillips pan head screws (H). (See Figure 5)

(H) x 2 Display

Figure 3

Display (A) Centris Head

Figure 4

Centris Head Display (A) (H) x 2

Figure 5

Attach Centris Head to Recessed Mount Display

1. Uninstall end lock using the 5/32" hex key (F). (See Figure 6)
2. Remove Centris head from array rail (A).

Centris Head Square Nut End Lock (A)

Figure 6

(A) Centris Head

Figure 7

1. Place display face down on a clean dry surface.

2. Place four 3/8" or 3/4" nylon spacers (L or M) over four mounting holes in display back (See Figure 8).

3. Align Centris head mounting holes with four nylon spacers (See Figure 8).
4. Secure Centris head to display using four M4 x 20mm Phillips pan head screws (J) [if using 3/8" (L) spacers], or four M4 x 30mm Phillips pan head screws (K) [if using 3/4" (M) spacers] (See Figure 8).

(J or K) (L or M) Centris Head Display

Figure 8

1. Slide display with Centris bracket onto array rail (A). (See Figure 9)

NOTE: Repeat previous steps for each additional display.

Display with Centris Bracket (A)

Figure 9

1. Reinstall end locks into mounting rail using the 5/32" hex key (F) (See Figure 10).

End Lock (A) End Lock Retaining Screw Centris Head

Figure 10

Display Installation - Interface Models

IMPORTANT ! : Interface brackets are designed specifically for Dell's quick-connect style monitors. Do not attempt to install any other type of monitors to these mounts!

1. Position monitor over mounting tabs on quick-connect bracket (A). (See Figure 11)
2. Lower monitor onto quick-connect bracket, inserting mounting tabs into top two top mounting holes on back of monitor. (See Figure 11)

mounting tabs

Figure 11

1. Slide base of monitor towards mount until lower tabs secure display to mount. An audible "click" should be heard. (See Figure 12)

(side view) ③

Figure 12

Display Removal - Interface Models

WARNING: Only remove display from mount when the display can be lifted up from the mount! DO NOT remove display unless the display is in the upright position! (See Figure 13)

1. Press quick release tab on back of display to release display from faceplate. (See Figure 13)
2. Pull bottom of display away from faceplate. (See Figure 13)
3. Lift display up from faceplate. (See Figure 13) and (See Figure 14)

① quick release tab ③

Figure 13

Technical diagram of a mechanical assembly with numbered components and directional arrows indicating motion or force.

Figure 14

ADJUSTMENTS

Display Adjustment

The MSP-DCCKTP Series mount allows horizontal, pitch, and rotational adjustment of each display.

The MSP-DCCKTP Series mount also allows a full 360 deg. of display rotation with a maximum pitch range of 15^ up and 15^ down.

Display Horizontal Position Adjustment

To adjust display horizontal position:

1. Loosen Centris bracket rear adjustment knob (See Figure 15).
2. Slide Centris bracket with display left or right until properly positioned on array rail.
3. Tighten Centris bracket rear adjustment knob.

Horizontal Adjustment Knob

Figure 15

Display Pitch and Roll Adjustment

To adjust display pitch or roll position:

1. Loosen Centris bracket front adjustment knob. (See Figure 16)
2. Tilt display up or down, or adjust display roll left or right until properly positioned.
3. Tighten Centris bracket front adjustment knob.

Pitch/Roll Adjustment Knob

Figure 16

CABLE MANAGEMENT

The MSP-DCCKTP Series mount includes cable management features used to properly route and secure display cables.

To use the cable management features:

1. Connect cables to display.
2. Route cables through cable clips on array rail.
3. Route cables down pole and away from mount and secure to pole using sheath (R).

Cable Clips (R)

Figure 17

MSP-DCCKTP SERIES

Installation Instructions