99-3000R - Kit voiture Metra - Free user manual and instructions
Find the device manual for free 99-3000R Metra in PDF.
User questions about 99-3000R Metra
0 question about this device. Answer the ones you know or ask your own.
Ask a new question about this device
Download the instructions for your Kit voiture in PDF format for free! Find your manual 99-3000R - Metra and take your electronic device back in hand. On this page are published all the documents necessary for the use of your device. 99-3000R by Metra.
USER MANUAL 99-3000R Metra
INSTALLATION INSTRUCTIONS FOR PART 99-3000
APPLICATIONS
CHEVROLET:
BLAZER 92-94/PICKUP 88-94/SUBURBAN 92-94
GMC:
C-SERIES 88-94/SUBURBAN 92-94/YUKON 92-94
99-3000
AW-333GM/DW-3000/CK-333GM
99-3000
KIT FEATURES
• DIN Mount Radio Provision
• ISO Mount Radio Provision
KIT COMPONENTS
A) Radio Housing • B) ISO Brackets
natural_image
Front view of a car air conditioner unit with fan, grille, and control panel (no visible text or symbols)
natural_image
Technical line drawing of a mechanical housing or enclosure component (no text or symbols)
natural_image
Technical line drawing of two mechanical component parts (no text or symbols)TOOLS REQUIRED:
Small Flat Blade Screwdriver/ Panel Removal Tool
• Phillips Screwdriver
TABLE OF CONTENTS
Dash Disassembly ....1
Kit Preparation 2
Kit Assembly
- DIN Mount Radio Provision .... 3
- ISO Mount Radio Provision .... 3
Final Assembly 4
*Note:
Refer also to the instructions included with the aftermarket radio.
CHEVROLET:
BLAZER 92-94/PICKUP 88-94
SUBURBAN 92-94
GMC:
C-SERIES 88-94/SUBURBAN 92-94
YUKON 92-94
1 Disconnect the negative battery terminal to prevent an accidental short circuit.
2 Pull out on the bottom of the radio trim bezel. Unhook the top corners of the bezel and remove. (Figure A)
3 Remove the metal fastening clips from the bottom of the factory dash panel and attach them to the same location on the Replacement Dash Panel. (Rear inside corner view shown) (Figure B)
Continue to kit assembly.
natural_image
Technical line drawing of a mechanical component with internal parts and directional arrows (no text or symbols)
natural_image
Technical line drawing of a mechanical assembly with a bracket and base, showing motion direction (no text or symbols)CHEVROLET:
BLAZER 92-94/PICKUP 88-94
SUBURBAN 92-94
GMC:
C-SERIES 88-94/SUBURBAN 92-94
YUKON 92-94
1 Remove the a/c vents from the factory dash panel by releasing the spring fastening clips securing them to the panel. Mount the vents to the Replacement Dash Panel by inserting the inner edge of the vent into the center inside pivot hole and the outer edge of the vent into the outer pivot hole. Using the same metal spring clips and mounting procedures from the original truck panel to mount the vents to the Replacement Dash Panel. (Figure A)
Continue to kit assembly.
natural_image
Technical line drawing of a car air duct system with two components and airflow arrows (no text or symbols)CHEVROLET: BLAZER 92-94/PICKUP 88-94 SUBURBAN 92-94
GMC: C-SERIES 88-94/SUBURBAN 92-94 YUKON 92-94
DIN MOUNT RADIO PROVISION
Note: Refer also to the instructions included with the aftermarket radio.
1 Slide the DIN cage into the radio housing and secure by bending the metal locking tabs outward. (Figure A)
2 Slide the aftermarket radio into the cage until it snaps into place. (Figure A)
Continue to final assembly.
natural_image
Technical line drawing of a device housing with internal compartments and a panel assembly (no text or symbols)ISO MOUNT RADIO PROVISION
Note: Refer also to the instructions included with the aftermarket radio.
1 Mount the ISO brackets to the radio using the screws supplied with the radio.
2 Slide the radio into the radio housing until the ISO brackets snap into place. (Figure A)
Continue to final assembly.
text_image
A RIGHT SIDE CLIPFINAL ASSEMBLY
text_image
A B C D(A) Strip wire ends back 1/2"
B) Twist ends together
C) Solder
D) Tape
1 Locate the factory wiring harness in the dash. Metra recommends using the proper mating adapter and making connections as shown. (Isolate and individually tape off the ends of any unused wires to prevent electrical short circuit.)
2 Re-connect the negative battery terminal and test the unit for proper operation.
3 Reassemble radio and dash assemblies in reverse order of disassembly.
FINAL WIRING CONNECTIONS
Make wiring connections using the EIA color code chart shown below and the instructions included with the head unit. Metra recommends making connections as shown below; Strip, Splice, Solder, Tape. Isolate and individually tape off ends of any unused wires to prevent electrical short circuit.
METRA / EIA WIRING CODE
| 12V Ignition / Acc. .... . Red | Right Front (+) .... . Gray |
| 12V Batt / Memory. .... . Yellow | Right Front (-).... Gray/ Black |
| Ground. .... . Black* | Left Front (+) .... . White |
| Power Antenna. .... . Blue | Left Front (-). .... . White / Black |
| Amp Turn-On. .... . Blue / White | Right Rear (+) .... . Violet |
| Amp Ground. .... . Black / White | Right Rear (-) .... . Violet / Black |
| Illumination. .... . Orange | Left Rear (+) .... . Green |
| Dimmer. .... . Orange / White | Left Rear (-) .... . Green / Black |
*NOTE: When a Black wire is not present, ground radio to vehicle chassis.
All colors may not be present on all leads due to manufacturer's specifications.
NOTES
99-3000 INSTRUCTIONS