SWD4000-RM - Vacuum Cleaner Sun Joe - Free user manual and instructions

USER MANUAL SWD4000-RM Sun Joe

A Division of Snow Joe ^25 , LLC

ELECTRIC WET/DRY VACUUM

8.5-AMP | 4-GAL | 3.5 PEAK HP | CYCLONE FILTRATION

Model SWD4000-RM Form No. SJ-SWD4000-RM-880E-M-V1

THANKS FOR YOUR PURCHASE OF A REMANUFACTURED PRODUCT.

To make sure you get the most out of your product, be sure to register online at

sunjoe.com

to enjoy full product support.

OPERATOR'S MANUAL

A Division of Snow Joe ^13 , LLC

ELECTRIC WET/DRY VACUUM

8.5-AMP | 4-GAL | 3.5 PEAK HP | CYCLONE FILTRATION

Model SWD4000-RM Form No. SJ-SWD4000-RM-880E-M-V1

IMPORTANT!

Safety Instructions

All Operators Must Read These Instructions Before Use

Any electrical appliance can be dangerous if used incorrectly. Some of the safety precautions given in this manual apply generally to many appliances. Other warnings are specific to the use of this electric wet/dry vacuum.

Always follow these safety guidelines. Failure to do so may result in personal injury or property damage.

⚠ WARNING! This unit can be dangerous! Careless or improper use can cause serious injury.

General Safety

Before using, be sure that everyone using this tool reads and understands all safety instructions and other information contained in this manual. Save this manual and review it frequently prior to using this tool and when instructing others on the proper operating procedures.

⚠️CAUTION! Wear appropriate hearing protection during use. After long periods of extended use, the noise generated

1. Keep bystanders and children away – All bystanders, including children and pets, should be kept a safe distance away from the work area.
2. Disconnect tool – Disconnect the wet/dry vacuum from the power supply when not in use, before servicing, when transporting, or when changing accessories.
3. Do not use in dangerous environments - Do not use the wet/dry vacuum in rain, damp or wet locations. Do not operate the wet/dry vacuum in gaseous or explosive atmospheres or use the wet/dry vacuum to pick up flammable or combustible liquids. Motors in these tools normally spark, and the sparks might ignite fumes.
4. Check for damaged parts – Before using the wet/dry vacuum, repair or replace any part that is damaged. In addition, check for alignment of moving parts, binding of moving parts, breakage of parts, and any other conditions that may affect the tool's operation.
   Inspect the appliance cord periodically. If damage is found, have it repaired by an authorized service facility. Extension cords should also be inspected periodically and immediately replaced if damaged.
5. Avoid unintentional starting – Make sure the switch is off before plugging in the appliance.
6. Use the right tool – Do not force the tool or any attachment on the tool to do a job for which they were not designed.

7. Wear face or dust masks – If operated in dusty environment, the use of a face or dust mask specially designed to filter out microscopic particles is

8. Store idle tool indoors - When not in use, the wet/dry vacuum should be stored indoors in a dry and locked-up place out of the reach of children.

9. Stay alert – Watch what you are doing. Use common sense. Do not operate the wet/dry vacuum when you are tired or under the influence of drugs, alcohol or other medication.

⚠️DANGER! Do not manually place objects into the vacuum inlet while operating the unit, as this can seriously damage the unit and/or harm the operator. Keep both hands away from the air inlet while the power is on.

DO NOT ATTEMPT to remove material or hold material to be vacuumed when the wet/dry vacuum is on. Make sure the wet/dry vacuum is off when clearing jammed material from the vacuum inlet.

Personal Safety

DANGER! Do not vacuum, or use this wet/dry vacuum near flammable liquids, gases, or explosive vapors like gasoline or other fuels, light fluids, cleaners, oil-based paints, natural gas, hydrogen, or explosive dusts like coal dust, magnesium dust, grain dust or gun powder. Sparks generated by the motor can ignite flammable vapors or dust.

• This vacuum is only for indoor use. Do not use it outdoors.
• Children in the work area must be supervised to ensure that they do not play with the appliance. This appliance is NOT a toy and should never be used as such.
• Never leave a machine that is ready for operation unattended at the workplace.

• Do not use the tool with a damaged plug. If the tool is not working as it should or has been dropped, damaged, left outdoors or dropped into water, contact the Snow Joe ^® + Sun Joe ^® customer service department at 1-866-SNOWJOE

• Maintain proper footing and use extra care when using the appliance on stairs.

• Service on the product must be performed by qualified repair personnel only. Service or maintenance performed by unqualified personnel could result in injury to the user or damage to the product.
• This wet/dry vacuum is intended for residential use only. Commercial use of this product is prohibited and will void the manufacturer's warranty.
• Never douse or squirt the unit with water or any other liquid. Clean the unit after use every time as described in the cleaning and storage section.
• Prevent cords, plastic bags, or similar items from getting sucked in, as these might wrap around the filter, which may cause an overload or blocking of the motor. In such a case, switch the wet/dry vacuum off. Do not leave the wet/dry vacuum switched on with the motor overloaded or stalled.
  • Always operate the machine in an upright position. Do not operate it tilted to one side or even upside-down.

Electrical Safety

1. Ground fault circuit interrupter (GFCI) protection should be provided on the circuit(s) or outlet(s) to be used for this electric wet/dry vacuum. Receptacles are available having built-in GFCI protection and may be used for this measure of safety.
2. Make sure that the mains voltage matches that listed on the unit's rating label. Using the improper voltage can damage the motor and injure the user.
3. To prevent electric shock, use only with an extension cord suitable for indoor use only, such as SW-A, SOW-A, STW-A, STOW-A, SJW-A, SJOW-A, SJTW-A, or SJTOW-A.
   Before use, check that the extension cord is in good condition. When using an extension cord, make sure to

WARNING

Electric shock may cause SEVERE INJURY or DEATH. Heed these warnings:

• Do not allow any part of the electric wet/dry vacuum to make contact with water while it is in operation. If the appliance becomes wet while turned off, wipe dry before starting.
• Do not use an extension cord over 7.5 ft. The wet/dry vacuum comes equipped with a 6 ft power cable. Combined cord length must not exceed 13.5 ft. Any extension cord must be 18-gauge (or heavier) to safely power the wet/dry vacuum.
• Do not touch the appliance or its plug with wet hands or while standing in water. Wearing rubber boots offers some protection.

EXTENSION CORD CHART

Cord Length:	7.5 ft (2.3 m)
Min. Wire Gauge (A.W.G.):	18

1. To reduce the risk of electric shock, this appliance has a polarized plug (i.e. one blade is wider than the other). Use this appliance only with a polarized UL-, CSA- or ETL-listed extension cord recommended for indoor use only.

The appliance plug will fit into a polarized extension cord only one way. If the appliance plug does not fit fully into the extension cord, reverse the plug. If the plug still does not fit, obtain a correct polarized extension cord. A polarized extension cord will require the use of a polarized wall outlet. The extension cord plug will fit into the polarized wall outlet only one way. If the plug does not fit fully into the wall outlet, reverse the plug. If the plug still does not fit, contact a qualified electrician to install

1. To prevent the appliance cord from disconnecting from the extension cord during operation, make a knot with the two cords as shown in Table 1.

Table 1. Method of Securing Extension Cord

(A) Tie cord as shown

(B) Connect plug and receptacle

1. Do not abuse the cord. Never pull the wet/dry vacuum by the cord or yank the cord to disconnect it from the receptacle. Keep the cord away from heat, oil and sharp edges.

Double-Insulated Appliances

In a double-insulated appliance, two systems of insulation are provided instead of grounding. No grounding means is provided on a double-insulated appliance, nor should a means for grounding be added to the appliance. Servicing a double-insulated appliance requires extreme care and knowledge of the system, and should be performed only by qualified service personnel at an authorized Snow Joe ^3 + Sun Joe ^3 dealer. Replacement parts for a double-insulated appliance must be identical to the parts they replace. A double-insulated appliance is marked with the words "Double Insulation" or

Specific Safety Rules for Wet/Dry Vacuum

This motor-operated wet/dry vacuum is intended for vacuuming wet or dry material and dust. This equipment is not suitable for vacuuming ashes, coals, toxic, flammable or other hazardous materials. Vacuuming of glowing materials and dusts that are combustible, explosive or hazardous to one's health is prohibited. The manufacturer will not be held responsible for injuries resulting from incorrect use of the device or from use that does not comply with the directions.

NOTE: This wet/dry vacuum is intended for indoor household use only.

⚠ WARNING! To reduce the risk of electric shock, do not use outdoors or in damp or wet environments. Do not expose to rain. Store indoors in a dry place.

⚠ WARNING! For your own safety, read and understand the operator's manual. Do not run the unit unattended. Do not pick up hot ashes, coals, toxic substances, flammable materials or other hazardous debris. Do not use the device in an area with explosive liquids or vapors.
⚠️CAUTION! To reduce the risk of injury, unplug the unit before servicing.

- Do not use the wet/dry vacuum without filters in place.

- When vacuuming, do not place the equipment on heat sensitive floors. For safety reasons, use a fireproof base when necessary.

• Empty and clean the vacuum before and after vacuuming to avoid the accumulation of debris.

CAUTION! Do not vacuum hazardous substances.

Safety Symbols

The following table depicts and describes safety symbols that may appear on this product. Read, understand and follow all instructions on the machine before attempting to assemble and operate.

Symbols	Descriptions Symbols	Descriptions
	Safety alert. Exercise caution.		To reduce the risk of injury,user must read the instruction manual.
	To reduce the risk of electric shock, do not use outdoors or in damp or wet environments.Do not expose to rain. Store indoors in a dry place.		WARNING! Always turn the machine OFF and disconnect the electrical power before conducting inspection, clearing and maintenance. Remove the plug from the outlet immediately if the cord is damaged or cut.
	Immediately remove the plug from the mains if the power cable is damaged, frayed or entangled.Always keep the power cable away from heat, oil and sharp edges.		DOUBLE INSULATION -When servicing, use only identical replacement parts.

Know Your Electric Wet/Dry Vacuum

Read the owner's manual and safety instructions carefully before operating the electric wet/dry vacuum. Compare the illustration below to the electric wet/dry vacuum in order to familiarize yourself with the location of the various controls and adjustments. Save this manual for future reference.

1. Attachment handle 2. Sliding block 3. Suction hose 4. Hose connector 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17. 18. 19. 20. 21. 22. 23. 24. 25. 26. 27. 28. 29. 30. 31. 32. 33. 34. 35. 36. 37. 38. 39. 40. 41. 42. 43. 44. 45. 46. 47. 48. 49. 50. 51. 52. 53. 54. 55. 56. 57. 58. 59. 60. 61. 62. 63. 64. 65. 66. 67. 68. 69. 70. 71. 72. 73. 74. 75. 76. 77. 78. 79. 80. 81. 82. 83. 84. 85. 86. 87. 88. 89. 90. 91. 92. 93. 94. 95. 96. 97. 98. 99. 100.

1. Attachment handle
2. Sliding block
3. Suction hose

4. Hose connector

5. Storage hook

6. Carrying handle
7. Power head

8. Lockina block

9. Metal extension tubes (2)

10. Wet + dry floor brush
11. Carpet + floor brush
12. Dust brush

Unpacking

Carton Contents

• Electric wet/dry vacuum
- Suction hose
- Extension tubes (2)
- Wet + dry floor brush
- Carpet + floor brush
- Dust brush
- All-purpose nozzle
- Crevice nozzle
• Manuals + Registration card

1. Carefully remove the electric wet/dry vacuum and check to see that all of the above items are supplied.
2. Inspect the product carefully to make sure no breakage or damage occurred during shipping. If you find damaged or missing parts, DO NOT return the unit to the store. Please call the Snow Joe ^® + Sun Joe ^® customer service center at 1-866-SNOWJOE (1-866-766-9563).

NOTE: Do not discard the shipping carton and packaging material until you are ready to use the wel/dry vacuum. The packaging is made of recyclable materials. Properly dispose of these materials in accordance with local regulations.

IMPORTANT! The equipment and packaging material are not toys. Do not let children play with plastic bags, foils or small parts. These items can be swallowed and pose a suffocation risk!

Assembly

AWARNICIT

1. Simultaneously depress the dual locking buttons on either side of the hose connector. Insert the hose connector into the air inlet hole and push firmly to secure (Fig. 1).

Fig. 1 Hose connector Dual locking buttons Air inlet Suction hose

1. Two extension tubes are included with the unit. If needed, take the slightly narrowed end of the first extension tube and using a twisting motion, insert into the attachment handle. Press firmly to secure. In the same manner, assemble the second tube (Fig. 2).

Fig. 2 Extension tubes Attachment handle Extension tube

Operation

WARNING! This equipment incorporates parts such as switches, motors or the like that tend to produce arcs or sparks that can cause an explosion. Do not pick up flammable, combustible, or hot materials. Do not use around explosive liquids or vapors, as electrical devices produce arcs or sparks which can cause a fire or explosion – do not use at filling stations or anywhere gasoline is stored or dispensed.

Starting + Stopping

Do not switch on the wet/dry vacuum until it has been completely assembled. Before switching on the unit, always check the power cord for signs of damage. Use only intact cords.

⚠ WARNING! Damaged cords pose a severe risk of injury. Replace damaged cords immediately.
⚠ WARNING! Before switching on the wet/dry vacuum, make sure that it is not in contact with any foreign objects.

1. Make sure the filters are installed before starting.
2. Make sure the power head and the suction hose are installed properly and locked securely.
3. Install the desired brush attachment onto the end of the hose. Use the extension tubes if needed.
4. Check that the electrical supply voltage and frequency (Volt/Hz) correspond to those specified on the rating plate. Plug the power cord into the outlet (Fig. 4). If an extension cord is used, make a knot with the two cords as shown in Table 1.

1. To stop the unit, turn the ON/OFF switch to the OFF position (Fig. 5), as indicated.
2. To adjust the strength of the airflow, push the sliding block on the attachment handle up or down (Fig. 6).

Fig. 6 Attachment handle Sliding block

1. To use the blower function, make sure the unit is turned off. Then remove the hose from the air inlet hole and insert into the blower flap by depressing the dual locking buttons. Push firmly to secure (Fig. 7).

Fig. 7 Dual locking buttons Hose connector Blower flap

Operating Tips

• Be extremely careful when working on slopes and stairs.
  • Always move forward by walking. Never run.
• Clean up after using the wet/dry vacuum. Dispose of debris appropriately.
  • Always use the carrying handle for transporting the equipment.

⚠ WARNING! To avoid personal injury, wear ear protectors when operating this unit. Wear a face mask or dust mask in dusty locations.

Air Inlet

Never cover the air inlets. Keep them free from obstructions and debris. They must always remain clear for proper motor cooling.

WARNING! To avoid personal injury, do not wear loose fitting clothing or articles such as scarves, necklaces, chains, ties, etc., that could get drawn into the air inlet. To make sure long hair does not get drawn into the air inlet, tie back long hair.

Basic Vacuum Procedures

⚠ WARNING! Do not vacuum drywall dust, fireplace soot or ash with the unit. This is very fine dust which will not be captured by the filter and may cause damage to motor.
⚠ WARNING! The foam filter must be used for wet vacuuming, and make sure to clean the foam filter after wet vacuuming.

- Place the equipment on a level surface that is not heat sensitive.

• Always use the suction hose for vacuuming. Hold the suction hose at a distance of approximately 0.4 in. (1 cm)

- Clean or change the filters (see Maintenance section) if the suction performance deteriorates. Never use the appliance without the filter.

⚠ WARNING! Never remove the power head without first turning the power switch to the OFF position and unplugging the unit from the main power source.

Releasing and Assembling the Power Head

WARNING! To prevent personal injury, make sure the switch is in the OFF position and the unit is unplugged before attaching or removing the power head.

1. To remove the power head, lift and release the locking blocks to open up the housing (Fig. 8).

Fig. 8 Power head Locking blocks

1. To reattach the power head, fit the power head onto the tank and fasten the locking blocks.

NOTE: The power head must be attached any time the unit is being operated.

1. Remove the power head from the collection tank.
2. Remove all the inner housing components as shown (Fig. 9).

Fig. 9 Nylon mesh Foam filter Multiple filtration Inlet filter Dust tube Dust tank

1. Separate the dust tube from the inlet filter by rotating clockwise to unlock (Fig. 10).

Fig. 10 inlet filter

Cleaning The Dust Tank

Clean the equipment routinely after each use:

1. Before all the inner housing components are re-installed, empty the dust tank (Fig. 11). Clean the tank with water and allow it to dry completely.

Line drawing of a trash bin with a lid and spilling particles from a container (no text or symbols)

1. To re-assemble the inner housing components, lock the dust tube by rotating counter-clockwise. Then place all the components back into the dust tank in the order shown (Fig. 12).

Fig. 12 Nylon mesh Foam filter Multiple filtration Inlet filter

Storage

1. Examine the electric wet/dry vacuum thoroughly for worn, loose or damaged parts. Should you need to repair or replace a part, contact an authorized Snow Joe ^5 + Sun Joe ^6 dealer or call the Snow Joe ^8 + Sun Joe ^8 customer service center at 1-866-SNOWJOE (1-866-766-9563) for assistance.
2. Examine the appliance cord thoroughly for signs of excess wear or damage. If it is worn or damaged, replace it immediately.
3. Store the wet/dry vacuum indoors in a clean, dry and locked location out of the reach of children and animals.
4. When not in use, the extension hose can be temporarily stored at the side of the unit by inserting the extension tube hook into the storage hook (Fig. 13).

Fig. 13 Extension tube hook Storage hook

1. When not being used, the accessories can be temporarily stored at the back of the unit (Fig. 14).

Recycling + Disposal

The product comes in a package that protects it against damage during shipping. Keep the package until you are sure that all parts have been delivered and the product is functioning properly. Recycle the package afterwards or keep it for long-term storage.

WEEE symbol. Waste electrical products should not be disposed of with household waste. Please recycle where facilities exist. Check with your local authority or local store for recycling regulations.

Service and Support

If your Sun Joe ^® SWD4000-RM electric wet/dry vacuum requires service or maintenance, please call the Snow Joe ^® + Sun Joe ^® customer service center at 1-866-SNOWJOE (1-866-766-9563).

Model and Serial Numbers

When contacting the company, reordering parts or arranging service from an authorized dealer, you will need to provide the model and serial numbers, which can be found on the decal located on the housing of the unit. Copy these numbers into the space provided below.

Troubleshooting

⚠ WARNING! Always unplug the power cord before performing any adjustments, maintenance or repairs to your electric wet/dry vacuum.

Problem Possible Cause Possible Solution
Device does not start	Mains voltage is not present Check power supply	cord, breakers, fuses.If damage is found, contact a qualified electrician to repair
	The equipment is not switched ON	Switch on the equipment
	The collection tank is full	Empty the collection tank
	Defective appliance cord or ON/OFF switch	Contact Snow Joe^a customer service at 1-866-SNOWJOE (1-866-766-9563) to repair
	Defective motor
Dust comes out from motor cover	The nylon mesh filter is missing or damaged	Attach or replace the nylon mesh filter
	There is a blockage in the nozzle, hose, or air inlet.The nylon mesh filter is clogged by fine dust	Check the unit for blockage. Clean or replace the nylon mesh filter.

Optional Accessories

⚠ WARNING! ALWAYS use only authorized Snow Joe ^® + Sun Joe ^® replacement parts and accessories. NEVER use replacement parts or accessories that are not intended for use with this tool. Contact Snow Joe ^® + Sun Joe ^® if you are unsure whether it is safe to use a particular replacement part or accessory with your tool. The use of any other attachment or accessory can be dangerous and could cause injury or mechanical damage.

		ModelAccessor
①	Wet/Dry Vac Replacement Filter SWD4000-FTR

NOTE: Accessories are subject to change without any obligation on the part of Snow Joe ^® + Sun Joe ^® to provide notice of such changes. Accessories can be ordered online at snowjoe.com or via phone by contacting the Snow Joe ^® + Sun Joe ^® customer service center at 1-866-SNOWJOE (1-866-766-9563).

SNOW JOE ^® + SUN JOE ^® REFURBISHED GOODS WARRANTY

GENERAL CONDITIONS:

Snow Joe ^® + Sun Joe ^® operating under Snow Joe ^® , LLC warrants this refurbished product to the original purchaser for 90 days against defects in material or workmanship when used for normal residential purposes. If a replacement part or product is needed, it will be sent free of charge to the original purchaser except as noted below.

The duration of this warranty applies only if the product is put to personal use around the household. It is the owner's responsibility to correctly perform all maintenance and minor adjustments explained in the owner's manual.

HOW TO OBTAIN YOUR REPLACEMENT PART OR PRODUCT:

To obtain a replacement part or product, please visit snowjoe.com/help or email us at [e-mail] for instructions. Please be sure to register your unit beforehand to speed up this process. Certain products may require a serial number, typically found on the decal affixed to the housing or guard of your product. All products require a valid proof of purchase.

EXCLUSIONS:

- Wearing parts like belts, augers, chains and tines are not covered under this warranty. Wearing parts can be purchased at snowjoe.com or by calling 1-866-SNOWJOE (1-866-766-9563).

Snow Joe ^9 + Sun Joe ^6 may from time to time change the design of its products. Nothing contained in this warranty shall be construed as obligating Snow Joe ^9 + Sun Joe ^6 to incorporate such design changes into previously manufactured products, nor shall such changes be construed as an admission that previous designs were defective.

This warranty is intended to cover product defects only. Snow Joe ^® , LLC is not liable for indirect, incidental or consequential damages in connection with the use or misuse of the Snow Joe ^® + Sun Joe ^® products covered by this warranty. This warranty does not cover any cost or expense incurred by the purchaser in providing substitute equipment or service during reasonable periods of malfunction or non-use of this product while waiting for a replacement part or unit under this warranty. Some states do not allow exclusions of incidental or consequential damages so the above exclusions may not apply in all states. This warranty may give you specific legal rights in your state.

HOW TO REACH US:

We're here to help Monday through Friday from 9AM to 7PM EST and Saturday and Sunday 9AM to 4PM. You can reach us at 1-866-SNOWJOE (1 866-766-9563), online at snowjoe/com, via email at [e-mail] or tweet us @snowjoe.

EXPORTS:

Customers who have purchased Snow Joe ^® + Sun Joe ^® products exported from the United States and Canada should