FK-1061 - Pregnant Turbosound - Free user manual and instructions

Type de produit	Passive PA Speaker
Marque	Turbosound
Modèle	FK-1061
Configuration	2-Way Full Range
Woofer	10" (254 mm) low-frequency driver
Tweeter	1" (25 mm) compression driver
Puissance admissible (RMS)	250 W
Puissance admissible (peak)	500 W
Impédance nominale	8 Ω
Réponse en fréquence	65 Hz - 20 kHz (±3 dB)
Sensibilité (1W/1m)	96 dB
Pression acoustique max	121 dB (continuous), 127 dB (peak)
Angle de couverture (H x V)	90° x 60° (rotatable)
Connecteurs d'entrée	2x Speakon NL4
Dimensions (H x L x P)	520 mm x 330 mm x 315 mm (20.5" x 13" x 12.4")
Poids net	14 kg (30.9 lbs)
Matériau du boîtier	15 mm birch plywood
Grille	Powder coated perforated steel with acoustically transparent foam
Accessoires fournis	Rubber feet, rigging points (M8)
Entretien et nettoyage	Clean with a soft, dry cloth; do not use solvents or abrasive cleaners. Check grille and connectors periodically.
Sécurité	Ensure stable placement; use safety cables when rigging. Do not expose to moisture or extreme temperatures.
Pièces détachées	Contact Turbosound or authorized dealer for replacement drivers, grilles, and speakon connectors. Repairs should be performed by qualified personnel.

Frequently Asked Questions - FK-1061 Turbosound

What type of speaker is the Turbosound FK-1061?

The FK-1061 is a passive 2-way full-range PA speaker designed for live sound reinforcement, fixed installations, and portable applications.

What is the power handling of the FK-1061?

It handles 250 W RMS and 500 W peak power. It is recommended to use an amplifier with power output between 250 W and 500 W at 8 Ω.

What connectors does the speaker have?

The FK-1061 uses 2x Speakon NL4 connectors for input and link-through. Pins are wired as +1/-1 (pin 1+ positive, pin 1- negative).

Can I use this speaker in a monitor position?

Yes, the FK-1061 has a trapezoidal cabinet and can be used as a floor monitor by placing it on its side. The rotatable horn allows 90° x 60° coverage in either orientation.

What is the frequency response of the FK-1061?

The frequency response is 65 Hz - 20 kHz (±3 dB), making it suitable for full-range audio reproduction without a subwoofer in moderate applications.

How should I clean and maintain the speaker?

Use a soft dry cloth to wipe the cabinet. Clean the grille with a vacuum or lightly compressed air. Do not use water or solvents as they may damage the components.

Is the FK-1061 suitable for outdoor use?

While it can be used outdoors under cover, it is not weatherproof. Protect it from rain, direct sunlight, and extreme humidity to prevent damage.

What amplifier should I use with the FK-1061?

Use a professional PA amplifier rated for 8 Ω loads, delivering 250-500 W per channel. Ensure the amplifier is not clipped to avoid driver damage.

Can I daisy-chain multiple FK-1061 speakers?

Yes, the second Speakon connector is a link-through output. However, ensure the total load impedance does not fall below the amplifier's minimum rating (e.g., two 8 Ω speakers in parallel = 4 Ω).

Where can I get spare parts or repair service?

Contact Turbosound or an authorized dealer for genuine replacement drivers, grilles, and connectors. Repairs should be carried out by qualified service personnel.

USER MANUAL FK-1061 Turbosound

Turbosound PROEL GROUP COMPANY

TCS-1061

Quickstart and Rigging User Guide

The Flying Systems

Safety Information

Safety Notes on Rigging

The Turbosound rigging system has been designed and constructed to a high standard of safety, and tested to the most demanding of specifications. In order to ensure the highest safety standards, this information on the assembly and safe use of rigging accessories must be understood and followed.

Only use Turbosound recommended rigging accessories, which are specifically designed for their intended purpose. Do not use Turbosound rigging with other types or brands of loudspeakers. This practice may compromise safety standards and Turbosound will not be responsible for damage or injury so caused. Do not modify the rigging accessories, or use them in a way other than that described in this user manual. Rigging components supplied as part of a complete assembly are non-interchangeable and must not be exchanged with the component parts of any other assembly. The component parts of a Turbosound rigging accessory must only be assembled using the fasteners and methods of assembly recommended in this guide. The use of fasteners and methods of assembly not specified or approved by Turbosound may result in an unsafe rigging assembly. Welding, or any other means of permanently fixing rigging components to each other or to cabinet fixing points is not allowed. Rigging assemblies must only be assembled using the appropriate parts and fixings as specified in this manual using the specific mounting instructions. Rigging components or assemblies must only be fixed to Turbosound loudspeaker cabinets using the cabinet fixing points, assembly methods and fasteners specified in this guide and the specific mounting instructions. When assembling the loudspeaker array ensure that all fixings are securely tightened before lifting the array.

Secondary Safeties

All TCS-1061 loudspeaker clusters flown in theatres, studios or other places of work and entertainment must, in addition to the principle load bearing means of suspension, be provided with an independent, and properly rated and securely attached secondary safety. Only steel wire ropes or steel chains of an approved construction and load rating

Quick Start Guide TCS series

O Turbosound PROEL GROUP COMPANY

Flying system components have been individually tested in accordance with the following regulations:

• The Health and Safety at Work Act 1974
• The Supply of Machinery (Safety) Regulations 1992
• The Lifting Operations and Lifting Equipment Regulations 1998

General Description

To take full advantage of the extremely flexible properties of the TCS series loudspeaker, the rigging system is designed to be intuitive, inherently safe, flexible, and simple to use. The load is taken entirely through the steel flygear and not through the cabinet's woodwork.

Rigging Parts

The rigging system consists of external steel flyplates fitted into rebates on the short sides of the loudspeaker enclosure forming the pivot point about which cabinets can be angled, working together with flyplates fitted towards the rear of the cabinet which mate with the flyplates of the cabinet above, providing a range of inter-cabinet angles.

A kit of parts is supplied with each TCS-1061 loudspeaker cabinet, consisting of:

8 x M6 x 35mm csk hex head screws

2 x front flyplate (not handed)

2 x rear flyplate (handed left and right)

4 x M6 x 45mm high tensile socket head screws

4 x M6 split washers

1 x 4mm Allen key

FK-1061 FLYING SYSTEM WILL SUPPORT A COLUMN OF UP TO 5 CABINETS DEEP

FK-1061 Flying Kit

Enables suspension of one column of TCS-1061 cabinets up to 5 deep from a single flybar, and utilising an identical flybar fitted with pull-back links to provide a pull-back for the whole cluster. One kit is required per loudspeaker array (two kits are required to hang left and right arrays). Blanking plates are provided to fit in place of the rear flying strips on the top cabinet.

The kit consists of:

2 x flybars

2 x pull-back links

2 x blanking plates

4 x M6 x 20mm socket head

screws

4 x M6 split washer

The single flybar provides three pick up points to allow for either a single lift point or double lift points, or to provide a single pull-back point or two pull-back points.

PULL-BACK LINK PULL-BACK BAR FLYBAR BLANKING PLATE

FB-1061 FLYING SYSTEM WILL SUPPORT A COLUMN OF UP TO 16 CABINETS DEEP

FB-1061 Flybar

Isometric line drawing of a rectangular frame with internal compartments and bolt holes (no text or symbols)

The FB-1061 is a fabricated steel frame consisting of welded box sections with front and rear cabinet attachment points and a central spine offering a total of nine pick up points to allow a range of cluster angles.
The FB-1061 flybar enables the creation of an array of up to cabinets up to 16 deep.

Setting the angle between cabinets

Tri-amp to bi-amp conversion

The conversion is achieved by changing the position of a jumper on the crossover board located inside the left side driver access door (when viewed from the front). The default jumper position as shipped from the factory is TRI-AMP as shown here.

Interior view of an electronic device with visible wiring and components (no text or symbols)

For TCS-1061/100 wide dispersion products relocate the jumper from the TRI-AMP PCB header to the centre position (BI-AMP 'HW' HORN) as shown below.

Close-up of electronic components including a CD, wires, and connectors (no visible text or symbols)

Quick Start Guide

TCS series

Turbosound