OTML19 - Security Camera Speco Technologies - Free user manual and instructions

USER MANUAL OTML19 Speco Technologies

Thank you for purchasing this network camera!

Please read this manual carefully before operating the unit and retain it for future reference.

Should you require any technical assistance, please contact Speco Technologies Technical Support.

Important Safeguards and Warnings

1. Electrical Safety

① installation and operation here should conform to local electrical safety codes.

Use a certified/listed 12V④③③lass 2 power supply only.

Please note: Do not connect two power supplying sources to the device at the same time; it may result in device damage! The product must be grounded to reduce the risk of electric shock.

Improper handling and/or installation could run the risk of fire or electrical shock.

Speco Technologies assumes no liability or responsibility for any fires or electrical shock caused by improper handling or installation.

2. Transportation

Heavy stress, violent vibration or exposure to water is not allowed during transportation, storage and installation.

7. Installation

Handle the device with care. ⑧eep the device right side up.

④o not apply power to the camera before completing installation.

④o not place objects on top of the camera.

4. Repair Professionals

①II examination and repair work should be done by qualified personnel only.

Speco Technologies is not liable for any problems caused by unauthorized modifications or user-attempted repair.

5. Environment

Table of Contents

1.1 Applications 7
1.2 LAN Access to Web Setup Interface 7

2 Live View 10

2.1 ⑩enu ②ar....10
2.2 Status Bar 10

3 Recording....12

4 Setup....13

4.1 PC Path Setup....13
4.2 Basic Setup 13

4.2.2 Privacy Mask....14
4.2.3 Image Setup 15
4.2.4 Region of Interest....16
4.2.5 OSD Setup 16

4.3 Network Setup 17

4.3.1 IP/Port Setup 18
4.3.2 PPPOE Setup 19
4.3.3 DDNS Client....19
4.3.4 Email Setup 20
4.3.5 FTP Setup 21
4.3.6 SNMP 21
4.3.7 UPNP 22
4.3.8 HTTPS 23
4.3.9 RTSP 23
4.3.10 IP Filtering....24
4.3.11 Zero Configuration 24

4.4 Event Setup 25

4.4.1 Motion Detection Setup....25

A E Record 27

Connection Guide

4.4 Applications

②elow are the main applications for use with the "P camera:

1. ⑩ake sure that the camera and the P③ are connected on the same local network. The camera is set to ④H③P by default and will be assigned an IP address by the ④H③P server. ⑩ake sure that the local network has a ④H③P server. Routers typically have a ④H③P server built in.

2. Install IP Scanner from the ③④ and run it after installation. IP Scanner is the tool for discovering the IP cameras on the local network.

SecureCloud - 8 Server File Edit View Help Tools Help Name: 9.0% File Size: 125.0000 Name: 125.0000 Address: 125.0000 VM Address: 125.0000 Windows ID Address: 125.0000 New Cncly PC speco technologies

1. In the device list, the IP address, model number, and ⑩①③ address of each device will be listed. Select the applicable device and double click to open up the web viewer. You can also manually enter the IP address in the address bar of the web browser.

SecurityGuard IP Server File Edit View Help Tools Name: Microsoft Office Name IP Address MAC Address Windows IP Address Dev Cardly IP Version Online: 057-128-53-69 36.0746.08.01.05 Other: 057-128-53-69 36.0746.08.01.05 http://www.xcsc.com/ 12.09.06.06

speco technologies® Username Password Login

①fter logging in the web interface will be displayed as shown below:

Thermal image showing a fire with smoke rising from a building, no visible text or symbols

5 Live View

The live view page has two function bars:

Parameter	Description
1.	10enuB@
2.	Status 59k

space technologies New Home Sub Stream Cam00 2017-10-19 17:32:10 Thu. 2048kbps 30fps

5.4 Menu Bar

Parameter icon Description
1 Main Stream		Switch es to main stream view
2 Sub Stream	Sub Stream	Switch es to sub stream view
3 Sensor alarm		Display s the Sensor alarm status:◆ White: Sensor alarm has not been set up◆ Blue: Sensor alarm has been set up and activated◆ Red: Sensor alarm has been triggered
4 Motion Alarm		Display s the Motion alarm status:◆ White: Motion alarm has not been set up◆ Blue: Motion alarm has been set up and activated◆ Red: Motion alarm has been triggered.
5 Privacy Mask Alarm		Display the Privacy mask alarm status:◆ White: Privacy mask alarm has not been set up◆ Blue: Privacy mask alarm has been set up and activated◆ Red: Privacy mask alarm has been triggered.
6 Full screen		Single click on this icon will bring the video to full screen.Double click on the video or hit "ESC" to exit full screen.
7 Manual Record		Single click will start the manual record mode on the PC
8 Schedule Recording		Shows the status of Schedule recording:◆ White: Schedule recording has not been set up.◆ Blue: Schedule recording has been set up and is currently recording
9 Audio		Toggle audio on/off
10 Screen Capture		Single click will capture a screenshot. The save directory can be configured in settings.

3 Recording

Recordings stored on SD cards and local PC can be played back via the Recording

interface.

space technologied Live Recording Setup File Type Image Setup Data Source SOCard Dec 2017 Fan: New New Add: The Ft: For 1 2 3 4 5 6 7 8 9 16 11 12 13 14 15 16 17 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 Today: 2017-12-14 Search 2017-04-15 09:00:00 12:00 00:00 09:00 18:00 20:00 12:00 24:00 16:00 28:00 21:00 24:00 ■ MicroScan □ TimeScan □ MicroScan

• Select the "File Type". Options are "Video" and "Image".
• Select the "Data Source". Options are "SD Card" and "⑨ocal".
• Select the date and time.
• Click Search.

4 Setup

4.1 PC Path Setup

1. ③hoose the local recording save directory. "Setup -> P③ Path Setup -> ⑥ile Path".

space technology PC Path Setup File Path Basic Setup Network Setup Event Setup Record System File Path Local Record Path: C:\Users\Administrator\Desktop\SPZ Local Snapshot Path: C:\Users\Administrator\Desktop\SPZ Browse Browse Save

1. ③lick "Save" to save the setting.

4.5 Basic Setup

4.5.1 Video/Audio Setup

1. Go to "Setup -> ②asic Setup -> Video/①udio Setup". ①udio and Video stream settings can be configured here.

space technologies Video/Audio Setup Privacy Mask Image Setup Region of Interest OSD Setup Basic Setup Standard: RAL StreamType: Main Stream Frame Rate: 35 StreamType: 2nd Stream Frame Rate: 35 Compression: CS4 Compression: CS4 Biterate Mode: 100 Biterate Mode: 100 Resolution: 40*400(D) Resolution: 847*890(D)

6rame Rate	The higher the frame rate, the smoother the video. 6rame rate is measured in fps (frames per second).
3ompression 3hoose the compression codec
2itrate 10ode	Bitrate mode◆ 32R (constant): The bitrate will stay constant◆ V2R (variable): 2itrate will be adjusted according to scene changes.
Resolution Sets the resolution or size of the image.
Video Quality Reference image quality when using V2R.
2itrate	The actual amount of data the camera is using for streaming. The higher the bitrate, the better the image quality will be.
GOP	Group of pictures. 4etermines how many frames are allowed between a "group of pictures". When a new scene begins in a video, until that scene ends, the entire group of frames (or pictures) can be a considered a GOP. If there is not much movement in the scene, setting a GOP value higher than the frame rate is fine, potentially resulting in less bandwidth usage. However, if the value is set too high, and there is a high frequency of movement in the video, there is a risk of frame skipping.
1udio 5nable Toggle audio
3ompression 3hoose the audio codec

1. ③lick "Save" to save the settings.

4.5.5 Privacy Mask

1. Go to "Setup > ②asic Setup > Privacy ⑩ask".

space technology PC Path Setup Basic Setup VideoAudio Setup Privacy Mask Image Setup Region of Interest OSD Setup

Note

Up to 4 zones can be defined within the image.

4.5.3 Image Setup

1. Go to "Setup > ⑦asic Setup ImImage Setup
2. See the table below for detail descriptions of the image settings.

PC-PLB Setup Cable Setup Visible Setup Fixed Block Structure Setup Coverage of Interior CSS Setup Network Setup Event Setup Record System Micro PCB Setup Micro PCB Setup Micro PCB Setup Micro PCB Setup Micro PCB Setup Micro PCB Setup Micro PCB Setup Micro PCB Setup Micro PCB Setup Micro PCB Setup Micro PCB Setup Micro PCB Setup Micro PCB Setup Micro PCB Setup Micro PCB Setup Micro PCB Setup Micro PCB Setup Micro PCB Setup Micro PCB Setup Micro PCB Setup Micro PCB Setup Micro PCB Setup Micro PCB Setup Micro PCB Setup Micro PCB Setup Micro PCB Unit Micro PCB Unit Micro PCB Unit Micro PCB Unit Micro PCB Unit Micro PCB Unit Micro PCB Unit Micro PCB Unit Micro PCB Unit Micro PCB Unit Micro PCB Unit Micro PCB Unit Micro PCB Unit Micro PCB Unit Micro PCB Unit Micro PCB Unit Micro PCB Unit Micro PCB Unit Micro PCB Unit Micro PCB Unit Micro PCB Unit Micro PCB Unit Micro PCB Unit Micro PCB Unit Micro PCB Unit Micro PCB Units

Parameter	Description
Hue	Sets the total color degree of the image.
Saturation	Sets how much color is displayed in the image. The higher the saturation, the brighter and vivid colors will appear to be. If set too high, the image will be oversaturated
Sharpness	Sets the sharpness level of edges.
10irror	3hangs the orientation of the image to be horizontally reversed.
Turn	3hangs the orientation of the image to be vertically reversed.
3amera 1nfs	3hangs the orientation of the image to 90", 180", 270" or normal.
6(9)(3) (1)nti-flicker) States.	◆ 50Hz: reduces flicker in 50Hz lighting conditions.◆ 60Hz: reduces flicker in 60Hz lighting conditions. This is common in the United States.◆ Normal: 3 correct sensor' temperature. When you choose this setting, it will correct every three minutes;Note: 3 correction will make a sound, the image will be paused for a moment, and then return to normal, it is a normal phenomenon, do not turn off, otherwise it will affect the image effect.
4 4 5 5 nhande the image effect
ZOO10	4 digital zoom, supports up to :

4.2.4 Region of Interest

1. Go to "Setup > ②asic Setup > Region of Interest".

space technology/ PC Path Setup Basic Setup VideoAudio Setup Privacy Mask Image Setup Region of Interest OSO Setup Network Setup Event Setup Record System VideoAudio Setup Privacy Mask Image Setup Region of Interest OSO Setup (Support 4 Zone) Enable Media Clear Failure CleanScreen Save

1. ③heck "⑤nable".
2. ③lick "⑥ull Screen" to select the entire area. ③lick and drag within the image to set up the
   zones. Up to 4 zones can be defined.
3. ③lick "③lear Screen" to clear previous settings if needed.
4. ③lick "Save" to complete the configuration.

Note

space technological PC Path Setup Basic Setup VisualAudio Setup Privacy Mesh Image Setup Region of Interest GSD Setup Network Setup Event Setup Record System VideoAudio Setup Privacy Mesh Image Setup Region of Interest GSD Setup Show Clock Show Frame Rate Show Channels Name: IFC Show User Info: SFE IPG X Save

1. ⑤nable and set the desired parameters to be displayed.

Parameter Description
Show clock	4isplas or hides the current time
Show 6ram Rate	4isplas or hides frame rate info
Show 3hannel Name	4isplays or hides the channel nickname. (up to 16 characters)
Show User Info	4isplas or hides user info. (up to 16 characters)

1. ③lick "Save" to complete >S④ configuration.

Note

Positions of the parameters can be moved around.

4.3.1 IP/Port Setup

1. Go to "Setup > Network Setup > IP/Port Setup".

space technology PC Path Setup Basic Setup Network Setup IPPort Setup PPPOC Setup DDNS Client E-mail Setup FTP Setup SNAP UPNP HTTPS RTSP IP Filtering Zero Configuration Max Connection: 10 DHCP: Swable IPv4 Address: 192.163.8.66 IPv4 Subnet: 235.255.255.3 IPv4 Gateway: 192.163.8.1 IPv4 DNS 1: 202.36.134.133 IPv4 DNS 2: 202.96.120.60 IPv4 MacAddr: 96.127.80.54.68 IPv5 Address: 2001.290.3200:1.17 IPv5 Gateway: 2001.290.3200:1.17 IPv5 DNS 3: 2001.099.2000.2017.33 IPv5 DNS 2: 2001.del:2000.2198.33 HTTP Port: 80 OnePort: 85 RTSP Port: 854 Save Record System

Parameter Description
⑩ax connection Up to 10 concurrent device logins are allowed.
④H③P	⑤nable or ④isable ④H ◆ ⑤nable ④H③P: If the network has a ④H③P server built in, it will assign an IP address to the camera. ◆ ④isable ④H③P (Static): Static networks require all devices to have their IP addresses
HTTP Port	◆ This is the access port to log in to the device. It will need to be forwarded properly in order to ensure smooth, latency-free communication.◆ The default value is "80", if another device on your network is using this port, please change to other value.◆ 5xample: 1 log in to the device with the HTTP port set to 82 through a webrowser, type: http://82
Onvif Port	◆ ONVI6 pro ocol communication po◆ The default value is "85"
RTSP Port	◆ Port used for streaming video to various clients◆ The default RTSP port is 554

1. Set the desired parameters and click "Save" to complete IP/Port Setup.

4.3.5 PPPOE Setup

1. Go to "Setup > Network Setup > PPPO( Setup)".

space technology PC Path Setup IPPIAT Setup *PPOE Setup DDVD Client E-mail Setup FTP Setup SNMP UPNP HTTPS RTSP IP Filtering Zero Configuration Basic Setup Network Setup IPPIAT Setup PPOE Setup Enable: Username: PABW01D. Save Live Recording Setup

1. ③heck "⑤nable".
2. ⑤nter thisername & password provided by the ISP.
3. ③lick "SaveThe camera will reboot."

Note

PPPO⑤: ①n advanced protocol that also s device to be more directly connected via a ④S node modem. This is option for advanced users only.

Parameter Description
⑤nable ③heck to enable ④④NS connectivity of the device.
Provider Speco ④④NS is the provider.
Hostname	⑤nter the nickname to be used for ④④NS. The name must be unique to be used for ④④NS.

1. ③lick "Save" to complete ④④NS ③client configuration.

4.3.4 Email Setup

1. Go to "Setup > Network Setup >⑤mail Setup".

space technologies PC Path Setup Basic Setup Network Setup IPProt Setup Service Setup JUNOS Client Signal Setup FTP Setup SNMP JUNP HTTPS RTSP IP Filtering Zero Configuration IPProt Setup PRICE Setup DOOS Client E-mail Setup FTP Setup SNMP JUNP HTTPs RTSP IP Filtering Zero Configuration [] Enable Motion Subject: Alarm Subject: SMTP Server: SMTP Port: 26 Sender Address: Sender Request: Recipient Address: Recipient Address: Recipient Address: Save Test Live Recording Setup

Test	3lick Test to verify the email setu

1. ③lick "Save" to complete ⑤mail Setup.

4.3.7 FTP Setup

1. Go to "Setup > Network Setup >⑥TP Setup".

space technologies PC Path Setup Basic Setup Network Setup IPPort Setup PPAOS Setup DDNS Client E-mail Setup FTP Setup 3MUF UPNP HTTPS RTSP IF Filtering Zero Configuration Enable Server: Port: 21 Mode: Passive Username: Password: Upload Directory: Test Save

Parameter Description
5nable 3heck to enable the 6TP function.
Server 5nter the 5TP server address.
Port	5nter the 6TP port number.The default value is "21"
10ode 3hoose the applicable mode: active or passive.
Username 5nter the username used to log in to the 6TP server.
Password 5nter the password used to log in to the 6TP server.
Upload Path 5nter the upload folder name here to receive the recorded files.
Test 7click Test to urify the 6TP status

iPCC Technologies PC Path Setup Basic Setup Network Setup iPPort Setup SNMP v1 SNMP v2 SNMP Port 161 (1-05535) Read Community public Write Community public Trap Address Trap Port 142 (1-05535) Save Live Recording Setup

1. ③lick "Save" to complete SN⑩P Setup.

4.3.7 UPNP

If this function is enabled, the camera can be quickly accessed through the ⑨①N.

1. Go to "Setup > Network Setup > UPNP".

space technology PC Path Setup Basic Setup Network Setup IPHost Setup PPPOC Setup UDVS Client Email Setup FTP Setup SNMP OPMP HTTPS KTSF IP Filtering Zero Configuration UPMP Delete Save

4.3.8 HTTPS

1. Go to "Setup > Network Setup > HTTPS".

space technologies PC Path Setup Basic Setup Network Setup IPPort Setup PPPOE Setup DNS Client E-mail Setup FTP Setup SNAP URLP HTTPe RTSP IP Filtering Zero Configuration Enable HTTPe Port: 421 Save

1. ③heck "⑤nable".

2. ③lick "Save" to complete HTTPS Setup.

Note

The check-box enables the use of the HTTPS protocol for accessing the camera. The text field designates the Hypertext Transfer Protocol Secure (HTTPS) port number. The default value is "443".

4.3.9 RTSP

1. Go to "Setup > Network Setup >RTSP".

space Technologies PC Path Setup Basic Setup Network Setup IP/Port Setup IP/Port Setup PPFCC Setup DCWS Client Email Setup FTP Setup SNMP UPINF HTTPS RTSP IP Filtering Zero Configuration Enable RTSP Port: 54 Save

4.3.10 IP Filtering

1. Go to "Setup > Network Setup > IP ⑥iltering".

space technogers PC Path Setup Basic Setup Network Setup FTP/Port Setup FTP/Port Setup DDOG Client E-mail Setup FTP Setup SHP* UPMP HTTPS BTP* FTP Setting IP/Port Setup PP/POE Setup OCHG Client E-mail Setup FTP Setup SNMP UPMP HTTPS BTP* IP Filtering IP Delete 101, 168.8.200 Paste Save

1. ③heck "⑤nable" IP ⑥iltering.
2. ⑤nter the IP address to filter. The IP address will be restricted access to the device.
3. ③lick "Save" to complete IP ⑥iltering Setup.

4.3.11 Zero Configuration

Zeroconfig can be used to discover the camera on the network when there is no ④H③P server available.

1. Go to "Setup > Network Setup > Zero ③onfiguration".

space technologies PC PDB Setup Basic Setup Networks Setup IPPort Setup PPDCE Setup DDNS Client E-mail Setup F1P Setup SNMP UPSP HTTPS RTSP IP Filters Zero Configuration Zero Configuration Friendly Name: PCAM 003464 Save

4.4 Event Setup

4.4.1 Motion Detection Setup

1. Go to "Setup > ⑤vent Setup > ⑩otion ④etection Setup".

space technologies PC Poll Setup Basic Setup Network Setup Event Setup Motion Detection Setup Video Event Alarm Alarm Record System Enable Region Setup Alarm Output Record Video Alarm Duration 0 (Sec)(5-100) Pre-record time 00 (Sec(1-10)) Record time 00 Sunday Monday Tuesday Wednesday Thursday Friday Saturday Time Period 1 00 00 00 - 23 59 59 Time Period 2 00 00 00 - 23 59 59 Time Period 3 00 00 00 - 23 59 59 Time Period 4 00 00 00 - 23 59 59 Select All □ Sunday □ Monday □ Tuesday □ Wednesday □ Thursday □ Friday □ Saturday Save

1. ③heck “⑤nable” to turn on the ⑩otion ④etection function, then check “①larm Output” and/or “Record Video”, depending on the desired action.

①Iarm Output: check this function to generate an alarm output signal to trigger connected alarm output devices.
Record Video: check this function to record video to the local P③ when a motion alarm is triggered.

Note

◆ Sensitivity: the higher the sensitivity, the less movement is required to trigger a motion event. The lower the sensitivity, the more movement is required to trigger a motion event.
◆ Threshold: the level that the motion detection needs to reach in order to trigger motion detection. The lower the threshold, the more likely that motion will trigger the event alarm.
◆ ⑥ull Screen: one-click to select all areas for motion detection.
◆ ③lear Screen: one-click to remove all areas for motion detection.

1. ③lick "Save" to complete the configuration.

2. Set up values for "①larm ④uration", "Pre-record Time", and "Record Time".

◆ ①larm ④uration: when the alarm is triggered, the alarm duration will last for time period specified here (range from 5 to 300 seconds). The alarm will not be triggered again until this period has ended.
◆ Pre-record Time: this field specifies in seconds how long the surveillance footage is recorded before motion detection is triggered. This applies to local recording only. ⑥ or NVR and SecureGuard, the pre-record time is configured on those respective platforms.
◆ Record Time: this field specifies in seconds how long the surveillance footage will be recorded after motion detection is triggered.

Notevv

Setting the “①larm ④uration” time shorter than the “Record Time” is recommended. >therwise not all the events might be recorded.

v

1. Set up the time periods for motion alarms to occur. >nly the specified time periods will trigger motion alarms. Up to 4 periods can be set per day.
2. ③lick "Save" to complete motion detection configuration.

Note

Privacy ⑩ ask and ① Iarm output can be set up in the same manner as ⑩otion ④ etection.

4.7 Record

4.7.1 Record Schedule

1. Go to "Setup > Record > Record Schedule".

space technology PC Paths Setup Basic Setup Network Setup Event Setup Record Recent Schedule SD card Management Snapshot Schedule Destination NAS Enable Sunday Monday Tuesday Wednesday Thursday Friday Saturday Time Period 1: 00 00 00 - 25 58 59 Time Period 2: 00 00 00 - 25 59 59 Time Period 3: 00 00 00 - 25 59 59 Time Period 4: 00 00 00 - 25 59 59 Select All ■ Sunday ■ Monday ■ Tuesday ■ Wednesday ■ Thursday ■ Friday ■ Saturday Save

1. ③heck "⑤nable" to set up scheduled recording.
2. Set up the time periods for scheduled recording. Up to 4 periods can be set per day.
3. ③lick "Save" to complete scheduled recording configuration.

4.7.2 SD card Management

1. Go to "Setup > Record > S④ card ⑩anagement".

space technologies PC Path Setup Record Schedule So card management Snapshot schedule Destination NAS Basic Setup ■ Offline Record ■ Auto Upload

4.7.3 Snapshot Schedule

1. Go to "Setup > Record > Snapshot Schedule".

space technology PC Path Setup Basic Setup Network Setup Event Setup Record Record Schedule SD card Management Supplement Schedule Orientation NAS System Record Schedule 3D card Management Snapset Schedule Destination NAS Enable Interval: 5 (1-600) Schedule Monday Tuesday Wednesday Thursday Friday Saturday Time Period 1 00 00 00 - 23 59 59 Time Period 2 00 00 00 - 23 59 59 Time Period 3 00 00 20 - 23 59 59 Time Period 4 00 00 00 - 23 59 59 Select All Sunday Monday Tuesday Wednesday Thursday Friday Saturday Save

1. ③heck "⑤nable" to turn on the snapshot function.
2. Set up the capture time interval. This specifies how often a snapshot will be captured.
3. Set up the time periods for scheduled recording. Up to 4 periods can be set per day.
4. ③lick "Save" to complete Snapshot Schedule configuration.

4.7.4 Destination

1. Go to "Setup > Record > ④estination". Recording destinations can be set here for scheduled, motion, and alarm events.

space technological PC Path Setup Record Schedule SQL Card Management Snapshot Schedule Destination IAS Basic Setup Record Live Recording Setup

N15	Video, alarm and snapshot will save to a N15

1. ③lick "Save" to complete ④estination configuration.

4.7.7 NAS

1. Go to "Setup > Record > N①S".

space technologies PC Path Setup Basic Setup Network Setup Event Setup Record Record Schedule SD card Management Snapshot Schedule Destination NAS Enable Server Address 192.168.028 Remote Directory InstExico Save

Parameter Description

Server 1address 5nter the N1S IP address

Remote 4directory 5nter the target remote directory

1. ③lick "Save" to complete N①S configuration.

4.8 System

4.8.1 Maintenance

1. Go to Select "Setup > System > ⑩aintenance".

space technology PC Path Setup Basic Setup Network Setup Event Setup Record System Maintenance Device Info Set Time User Admin Maintenance Device Info Set Time User Admin Factory Default Default Robot OK Auto Robot EarlyDay 0 0 OK Download template file(Current Settings) Browser System Variable File Upload Select File Browse System Firmware Upgrade Select File Options\Administrator Desktop File:24-63-54 Enable Writing Start Cancel Live Recording Setup

Parameter Description
6factory 4default Reset the system to factory default settings.
Reboot Reboots the device.
1uto Reboot Schedule an auto reboot for the device.
4download template file	3current settings of the device can be downloaded as a configuration file. This is useful if other units of the same model are installed and the same

4.8.2 System

1. Go to "Setup > System > ④ device Info".

space technology PC Path Setup Basic Setup Network Setup Event Setup Record System Maintenance Device Info Set Time User Admin Device Model: 123 PC Version: 0409-05-06-07-SPE Live Recording Setup

Parameter Description
4 device 10odel 10odel number for the IP 3amera
IP 3 Version IP 3amera firmware version

4.8.3 Set Time

1. Go to "Setup > System > Set Time".

space technology PC Push Setup Maintenance Device info Set Time User Admin Basic Setup Network Setup Crest Setup Record Systems Maintenance Time Zone: GMT-00:00 Time: 1" 42 32 Date: 2017.12.12 PC Time Sum: No NTP: Delete NTP Server: free.windows.com Save

4.8.4 User Admin

1. Go to "Settings > System > User ①dmin" to add users.

space technologist PC Path Setup Disk1 Setup Network Setup Event Setup Record System Maintenance Done into Set Time User Admin Maintenance Device Info Set Time User Admin No User Group Operate 0 Admin Manager Work Control 1 user Supernet Update 2 user User Security Control Add User

1. ③lick "①dd User" to add a user for the device.

User admin Group Manager Password ****** Confirm ****** Save Exit

◆ User: user name
◆ Group: Select between ⑩anager, Supervisor, and user.
◆ Password: Set/change user password.
◆ ③onfirm: ③onfirm password.

1. ③lick "Save" to complete User ①dmin configuration.

Note

⑩anager: ①dministrator level – can change all settings and manage users Supervisor: ③an change all settings, except manage users

11.12.1