OIPC72B7G - Security Camera Speco Technologies - Free user manual and instructions

USER MANUAL OIPC72B7G Speco Technologies

Close-up of a metallic industrial sensor device with visible branding and mounting bracket (no readable text or symbols)

Directions

Be careful not to cause any physical damage by dropping or throwing OIPC72B7G. Especially keep the device out of reach from children.

Do not disassemble OIPC72B7G. No After Service is assumed when disassembled.

Use only the power adapter provided with OIPC72B7G.

Be careful to prevent moisture or water penetration into the unit. Particular attention is needed when installing OIPC72B7G. The screw holes for the installation screws and pipe should be maintained water tight during the whole life time of the product.

All the electrical connection wires running into the unit should be prepared so that water from the outside cannot flow into the unit through the surface of the wires. Penetration of t moisture through the wire for extended period can cause malfunction of the unit or deteriorated image.

Note

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This

Caution

Any changes or modifications in construction of this device which are not explicitly approved by the party responsible for compliance could void the user's authority to operate the equipment.

Revision History

Date	Revision	Details
2012-09-01	1.0	First manual revision creation.

OIPC72B7G Owner's Manual

Contents 4

1. Introduction......6

1.1. Overview 6
1.2. Specification 7
1.3. Applications of OIPC72B7G 9

1. Product Description .... 10

2.1.Contents 10
2.2. Product Preview 11
2.3. Physical description.... 12
2.4 Functional Description 12

OIPC72B7G Owner's Manual

5.2. Cannot connect to the Video ....Error! Bookmark not defined.
5.3. Windows Vista or Windows 7 ....Error! Bookmark not defined.
5.4. Technical Assistance ....Error! Bookmark not defined.

1. Introduction

1.1. Overview

The OIPC72B7G is a state-of-the-art, multi-codec (H.264, MJPEG) IP camera (or network camera) built with embedded software and hardware technology. It enables real time transmission of synchronized video of up to D1 and audio data. Remote clients can connect to OIPC72B7G for the real time video data through various client solutions running on PC or mobile phones.

1.2. Specification

Category	Sub-Category	Details
Video	Compression	H.264/MJPEG
	Resolution	NTSC : 704x480, 640x480, 704x240,352x240, 176x112PAL : 704x576, 640x480, 704x288,352x288, 176x144
Audio(Bi-directional)	Up	N/A
	Down	N/A
Network	Interface	RJ-45, 10/100 Mbps
	Access network	Static, DHCP, PPP/PPPoE
	Protocol	IPv4/6, TCP, UDP, IGMP, ICMP, ICMPv6 etc.
I/O	Sensor In	1	NC, NO Selectable
	Relay Output	1	N/A
	RS-232C	N/A
	Mic/Line In	N/A
	Line Out	N/A
	CVBS output	N/A
	PoE	N/A

OIPC72B7G Owner's Manual

IP filtering for restricting administrative

access for audio and bi-audio

Sync to PC

Synchronize to PC

Manual

Manual time setting

Time management

Internet Time Server

DLS

Synchronize to Time Server

Day light saving

Active-X

SDK support

HTTP

Source filter

1.3. Applications of OIPC72B7G

• Security surveillance (buildings, stores, manufacturing facilities, parking lots, banks, government facilities, military, etc.)
• Remote monitoring (hospitals, kindergartens, traffic, public areas, etc.)
  • Teleconference (Bi-directional audio conference). Remote Learning, Internet broadcasting
  • Weather and environmental observation

2. Product Description

2.1. Contents

The product package contains followings :

Contents	Description	Remarks
OIPC72B7G	IP camera OIPC72B7G main unit
Power Adaptor	12VDC Adaptor	Optional item
CD	Software & User's Guide
Quick Reference Guide	Quick installation guide

2.2. Product Preview

2.2.1. Preview

OIPC72B7G	IP-Installer	CMS Software (Speco-NVR)
IP Camera	PC software to allocate an IP address to the IP Camera	PC software to view and record the A/V streaming data transmitted from IP camera. (Simultaneous support of up to 64 IP cameras)

2.3. Physical description

2.3.1. External View

Exterior view of a gray cylindrical security camera (no text or symbols visible)

Figure 2-1. External view of OIPC72B7G

2.4. Functional Description

• DC 12V : Power input for supplying 12V DC power.
  • Line Out

Connect speakers with built in amplifier. Audio from remote site is output through Line out in bi-directional audio mode.

- LINK/LAN LED (Orange)

It will be lit with orange color when network cabling is all right. Blinking orange color indicates that normal data transmission is under way. Off state indicates that there is trouble in network connection.

• ALARM IN/OUT and Composite Video Output

Status LED RJ-45 DC12V Sensor In(+) Sensor In(-)

Figure 2-3 ALARM IN/OUT and Composite Video Output Terminal of OIPC72B7G

Used for connecting P/T device, sensor, and composite video output. Pin assignments are as follows.

OIPC72B7G Owner's Manual

Photo Coupler Sensor1+ Sensor1- GND +12V Sensor1- NO/ NCType Sensor Device Sensor Device Sensor Power Supply Open CollectorType Sensor Sensor Power Supply

Figure 2-4. SENSOR Input connection

Factory Default Switch

A switch provided for returning the IP camera to factory default state. Open the cover to access the switch. Press the switch for a few seconds while power is applied.

3. On Site Installation

3.1. Ceiling or Wall Mounting

Please follow through the procedures in the order of the numbers for each procedure.

1. Open dome cover as following.

2. Fix the product using 3 screws and anchors

OIPC72B7G Owner's Manual

1. Combine dome cover.

4. Getting Started

Brief information for first time operation of OIPC72B7G is provided in this chapter.

4.1. PC Requirement

Video streaming data received from OIPC72B7G can be displayed or stored in a PC running client programs. Minimum requirement of the PC is described below:

	Recommended	Remark
CPU	Dual Core 3Ghz 3G above
Main Memory	2GB above
Operating System*	Windows XP
Web Browser	Internet Explorer 8.0 above
Graphic Card	256M above	Higher than 1600x1200
Network	100 Base-T Ethernet

* Operating Systems supported : Windows 2000 Professional / XP / Vista / 7

4.2. Quick Installation Guide

1. Connect PC and OIPC72B7G to network.

1) Prepare a PC to run programs for the installation and video connection (PC is needed to assign IP address to OIPC72B7G)
2) OIPC72B7G as shown in dotted line in Figure 4-1. The DC power is applied through DC adaptor.

Figure 4-1. Power and network connection

Install "IP installer and set IP parameters on OIPC72B7G

Insert the CD provided with product into the PC. Install WinPcap and IP Installer in sequence. Make sure that IP Installer can't run without WinPcap.

OIPC72B7G Owner's Manual

2. Install Speco-NVR

Speco-NVR is a multi-channel CMS program for to IP camera or Video server. Install Speco-NVR on remote PC to connect to these products. It is needed to assign connection information to Speco-NVR program before connection.

Insert the CD provided with product into the PC and install the Speco-NVR.

Admin Page Button

IP installer

OIPC72B7G Owner's Manual

OIPC72B7G Owner's Manual

3. Remote video connection to ONSIP O2D3

1) Connection through Web Viewer

Web Viewer offers simplest way of video connection to ONSIP O2D3. For video connection, enter the IP address of ONSIP O2D3 in the URL window of Internet Explorer as:

[e.g.] Port 80

Can be omitted the default port of 80

[e.g.] Port 8080

Note : Active-X module should be installed on your PC before actual connection. If your PC is not connected to the internet, you cannot download Active-X module. Most convenient way of installing the Active-X module is installing Speco-NVR which is available from the CD or our web site.

Connection to Admin Page

Basic Control

OIPC72B7G Owner's Manual

2) Connection through Speco-NVR

Click the camera assignment button for setting camera address. Input the description, address, Ch#, User ID, Password and port and then click the save button. After assignment procedure, you must click the SAVE button. You can see the live video when you click the live view button as below. When you exit Speco-NVR, you have to input the ID/PW, admin/1234. Details for the Speco-NVR can be found in [Speco-NVR User's Guide].

Camera Assignment Live view Exit Program Default ID/PW: admin/1234

Camera Assignment

OIPC72B7G Owner's Manual

4. Additional settings through connection to the Admin Page

All the parameters of new IP camera follows factory default values. For more sophisticated target application it is needed to change parameters. The admin page can be connected through

"http://IP_address:HTTP_port_number"/admin.htm

It is needed to enter ID and password of the administrator. Default ID and password are admin, 1234. It is highly recommended to change the ID and password to prevent illegal access to the IP camera. For more detailed information, please refer to the [Configuration_Guide] Guide.

5. Trouble Shooting

5.1. No power is applied

• In case of DC adaptor

If PoE is not applied, the power and network connection should be made through separate cables. It is recommended to use DC adaptor supplied by provider for the feeding of the power. In case of replacing the DC power supply, make sure that the power supply meets with the power requirement of the IP camera to prevent damage or malfunction.

5.2. Cannot connect to the Video

Check the status of the network connection through PING test.

Try the following on your PC :

• Start > Run > Cmd > Ping IP address (Ex : Ping 172.16.42.51)
• If "Reply from \~" message is returned (① in the figure below), the network connection is in normal state. Try connection to the video again. If the problem persists, or refer to other trouble shooting notes.
• If "Request timed out" message is returned. (② in the figure below), the network connection or network setting is not in normal state. Check the network cable and settings.

C:\WINDOWS\system32\cmd.exe Microsoft Windows XP (Version 5.1.2600) (C) Copyright 1985-2001 Microsoft Corp. C:\Documents and Settings\superman>ping 172.16.42.51 Pinging 172.16.42.51 with 32 bytes of data: Reply from 172.16.42.51: bytes=32 time\lm TTL=64 Reply from 172.16.42.51: bytes=32 time\lm TTL=64 Reply from 172.16.42.51: bytes=32 time\lm TTL=64 Reply from 172.16.42.51: bytes=32 time\lm TTL=64 Ping statistics for 172.16.42.51: Packets: Sent = 4, Received = 4, Lost = 0 (Dc loss), Approximate round trip times in milli-sounds: Minimum = Dcs, Maximum = Dcs, Average = Dcs C:\Documents and Settings\superman>

5.3. Windows Vista or Windows 7

Windows Vista and Windows 7 users need to configure UAC (User Access Control) and Privilege Level for proper recording and still video capture in Speco-NVR and Web Viewer.

1. UAC (User Access Control) configuration

1) Double-click "User Accounts" in control panel
2) Double-click "Turn User Account Control on or off"
3) Uncheck "Use UAC to help protect your computer"

Control Panel Home System and Maintenance Security Networks and Internal Windows and Hosted Programs User Accounts Parameters and Settings Clock, Language, and Programs View or Adjust Additional Options Close From User Accounts Add to remove user accounts Windows CardSpace Manage Information Cards that are easy to log on its online services Close From User Accounts Make changes to your user account Create a previous user account Change your password Change your account name Change your account type Change your account name Save the User Account Control as you want to use the Control Panel Turn on User Account Control (SASC) to make your computer more secure Use Account Control (SASC) can help prevent unauthorized changes to your computer. It should recommend that you have SASC based on how helped protect your computer. Use the User Account Control(SASC) is to help protect your computer

OIPC72B7G Owner's Manual

Open Troubleshoot compatibility Open file location Run as administrator Pin to Taskbar Pin to Start Menu Restore previous versions Send to Cut Copy Create shortcut Delete Rename Properties

MUSE Properties Identity Details Previous Versions General Shortcut Compatibility If you have problems with this program and it worked correctly on an earlier version of Windows, select the compatibility mode that matches that earlier version. Help me choose the settings Compatibility mode Run this program in compatibility mode for: Windows XP (Service Pack 3) Settings Run in 256 colors Run in 640x 480 screen resolution Disable visual themes Disable desktop composition Disable display scaling on high DPI settings Privilege Level Run this program as an administrator Change settings for all users OK Cancel Apply

1. UAC (User Access Control) configuration

1) Double-click "User Accounts" in control panel
2) Double-click "Change User Account Control setting"
3) Set to "Never notify"

1) Control Fund Use Accounts = 6p 11 January

2. Privilege Level Control

1) Select "NVR" icon on the desktop
2) Click right mouse button and select "properties"
3) Check "Privilege Level" in "Compatibility" tab

Open Troubleshoot compatibility Open file location Run as administrator Pin to Taskbar Pin to Start Menu Restore previous versions Send to Cut Copy Create shortcut Delete Rename Properties

MME Properties Security Details Previous Versions General Shortcut Compatibility If you have problems with this program and it worked correctly on an earlier version of Windows, select the compatibility mode that matches that earlier version. Help me choose the settings Compatibility mode Run this program in compatibility mode for: Windows XP (Service Pack 3) Settings Run in 256 colors Run in 640 x 480 screen resolution Disable visual themes Disable desktop composition Disable display scaling on high DPI settings Privilege Level Run this program as an administrator Change settings for all users OK Cancel Apply

OIPC72B7G Owner's Manual

5.4. Technical Assistance

If you need any technical assistance, please contact your dealer. For immediate service please provide the following information.

1. Model name
2. MAC address and Registration number
3. Purchase date
4. Description of the problem
5. Error message