H8D6M - Security Camera Speco Technologies - Free user manual and instructions

USER MANUAL H8D6M Speco Technologies

Thank you for purchasing our product. Speech Technologies is community developing and improving products. We reserve the right to modify product design and specifications without notice and without imposing any obligation.

Warnings

■ If the product does not work properly, please contact the dealer or where the product was purchased
Spatco Technologies is not responsible for any problems caused by improper operation or repair.
- Keep away from liquid while in use
All installation and operation here should conform to local electrical safety codes.
■ Make sure the power supply voltage is correct before using the camera.
■ Do not drop the camera or subject to physical shock
■ Do not use the device beyond specified voltage range.
■ Do not place the camera in extremely hot, told the opening temperature shall be (-1 F - 122°F), dusty or
damp locations, and do not expose it to high electromagnetic radiation
■ Toroidal heat accumulation, pool certification is required for operating environment

Introduction

This camera series is the latest technology and advanced circuit design, which features high definition and

sensitivity, low noise and distortion and supports HD video transmission with the common central cable.

ecouring the requirement of the H2 monitoring in the additional surveillance system.

High Resolution

Adapt high performance sensor, providing high definition and clear image.

● High Transmission Performance

Real-time transmission with high speed and long distance.

● High Light Compensation (HI.C)

Mask and compensation on the high light area.

DNR

Reduce noise from brightness and color signal.

OSD

Access the camera settings which can be clearly displayed through the main mean.

● White Balance

Adjust the coke temperature according to the environment automatically.

ICR Auto Switch

The filter will filter infrared light during the daytime and change to normal at night to

ensure a high sensitivity and clear image.

● AGC

Adjust the gain of amplifier, enabling the camera to input the standard video signal in different.

lighting condition.

● Wide Dynamic Range (WDR)

When there are both very bright and very dark areas simultaneously in the field of view, this function

will balance the brightness level and powder clear images.

● Backlight Compensation (BLC)

When the back of the captured object is too much bright, you can set BLC for the captured object to make it clearer.

Cables

Video switch: Four video output modes can be optional—AHD, EVL, CVI and CVBS. (a) remove the cover of the video switch cable; for build and press the button is the video switch cable for 5 seconds to switch the current video output

Installation

Before you start, please make sure that the wall or ceiling is shot up enough so w/stand three times the weight of the camera. Please install and use the camera in the dry environment. You'd better install back the lens cover or lower alone less than 4 hours after removing it. The mounting types of sensors are only for reference.

▶ Mounting for H8B6M

1. Drill the screw holes and the cable hole on the wall according to the drill template.

1. Rowe and connect the calories.
2. Secure the mounting base with camera to the wall with screens as shown below.

1. Bracket adjustment. Before adjustment, preview the image of the camera on a motion and then zoomed the fixed ring to adjust the view angle of the camera. Tighten the fixed ring after the adjustment.

▶ Mounting for HSD6M

1. Lessent the screws to open the lower done and then loosen the back screw to remove the mounting base.
2. Attach the drill template to the place where you want to fix the camera and 10 on drill 4 screw holes and 1 cable hole if you want to create the cables through the mounting base according to the drill template.

1. Radcland announced the ceiling fuse to the ceiling or wall with the seconds principal.

1. Tax the camera to the mounting base with the lock screw.

1. There-axis adjustment. Before adjustment, preview the image of the camera on a monitor and then adjust the camera according to the figure below to get an optimum angle.

2. Install the lower dome box to the camera with the screws and remove the protection film suit to complete the installation.

Specifications

Specifications\Models	1850M	1850M
Camera
Image Sensor	1/2.5" (CM) 3D
Recovery	832P
Image size	2540-2160
Video Output	AID+TVLC+VFC+VBS (current courses defined to HD+LVH)
Image System	PAL-NTSC
Electronic Shutter	Auto, 1/5Hz=1/1000Gb(PAL),1/6Hz=1/1000Gb(NTSC)
IR Distance (Ref)	52.8-65.6
Fuse Size	15fps
Max. Illumination	Color: 0.01 atm @E1.2, AGC ON, BW: 0.4 atm with TR
Lens	2.8-12mm (motor/beat)
Lens Mount	D14
SN Rati	a Sulf@AGC (OPT)
Ingress Protection	DN6	DN6&IK10
Functions
Function Control	USD (UTC control)
Dry &Night	L/R
W DR	Digital WDR
Digital NR	Yes
ASC	No
Auto White Balance	Yes
Defag	No
BLC	Yes
Clustive	Yes
Saturation	Yes
Sleepiness	Yes
Smart IR	Yes
Image Satting	Yes
Deficit Convection	Auto
Others
Power Supply	DC 12V (± 10V)
Power Consumption	LR 0V1< ± 2W; LR ON: ± 2W	BL 0V1< ± 2W; LR ON: ± 2.5W
Working Environment	-4 °F > 122 °F, 10 % - 90 (%relative humidity)
Dimensous (inch)	40.43 8.62s	40.99 4.40*

Model: 18B6M/18D6M

Federal Communications Commission (FCC) Statements

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.

FCC Responsible Party:

Specn Technologies

200 New Highway

Amylville, NY 1170

www.specotech.com