HTBIR1M - Security Camera Speco Technologies - Free user manual and instructions

USER MANUAL HTBIR1M Speco Technologies

① Contents......2
● Precautions....3, 4
Safety Instructions 5
● Package Contents......6
- Camera Installation 7-8
● Lens Adjustment ...... 9
Specifications....10

Precautions

Do not install the camera in extreme temperature conditions.

Cartoon illustration of two anthropomorphic smokestacks emitting flames, with a cloud above (no text or symbols)

Only use the camera under conditions where temperatures are between -10°C and +50°C. Be especially careful to provide ventilation when operating under high temperatures.

Do not install the camera under unstable lighting conditions.

Severe lighting change or flicker can cause the camera to work improperly.

Do not touch the front lens of the camera.

This is one of the most important parts of the camera. Be careful not to leave fingerprints on the lens cover.

Never keep the camera pointed directly at strong light.

Do not drop the camera or subject it to physical shocks.

Do not expose the camera to radioactivity.

CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE REFER SERVACING TO QUALIFIED SERVICE PERSONNEL. ISO14001 CE FC

The lightning flash with an arrowhead symbol, within an equilateral triangle is intended to alert the user to the presence of uninsulated dangerous voltage within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.

In USA and Canada, Use Class 2 Power Supply Only

INFORMATION - This equipment has been tested and found to comply with limits for a Class A digital device, pursuant to part 15 of the FCC Rules & CE Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications.

• This camera should be installed by qualified personnel only
  There are no user serviceable parts inside
  Do not disassemble this camera other than to make initial adjustments
• Use a UL approved regulated 24 volt AC or 12 volt DC power supply
• Use appropriate low voltage power cable to prevent fire or electrical shock
  Please insure that your installation area can support the weight of the camera

Please handle this camera carefully :

Do not use a strong or abrasive detergent when cleaning the camera
- Do not install near cooling or heating device

Package Contents

Please make sure that the following items are included in the Package:

1) HTBIR1M

• 1 Video Test Connector, Power Jack
- 1 Bracket Base
• 1 Wrench
- Set Screw
- 4 Tapping Screws 4x25
- 4 Hexagon Socket Screws M5x10
- 4 Plastic Anchor

CAMERA INSTALLATION

CONNECT POWER CABLE

1. WHEN USING 12 VOLTS DC (constant voltage 500mA)

Power Input : RED Center : (+) DC 12V Power Supply

1. WHEN USING 24 VOLTS AC (40 Volt Amps)

RED (+) BLACK:(-) AC 24V Power Supply

1. CONNECT VIDEO CABLE

1) WHEN USING IT AS ANALOG OUTPUT, CONNECT YELLOW COLOR BNC CABLE TO THE BNC JACK.

CAMERA INSTALLATION

Compatibility

1) HTBIR1M

WALL

LENS ADJUSTMENT

1) HTBIR1M

"A" Open the cap

Technical line drawing of a mechanical component with no visible text or symbols

2MP TVI 940nm Black IR LED Motorized Zoom Focus Camera with included Junction Box

2.8-12mm MFZ Lens

Exterior view of a black security camera with mounted lens and mounting flange (no visible text or symbols)

HTBIR1M (2.8-12mm)

SPECIFICATIONS

MODEL	HTBIR1M
Image Sensor	1/2.9 Inch SONY 2Mega CMOS Sensor
Pixels - total	2001 (H) X 1121 (V)
Pixels - Effective Resolution	1985 (H) X 1105 (V)1920X1080(1080p@30f / 1080p@25f)1280X720_CROP(720p@60f / 720p@50f)1280X720_CROP(720p@30f / 720p@25f)
Scanning System	Progressive Scan
S/N Ratio	50 dB
Video Output	1.0Vp-p Composite. 75 Ohms / 1.0Vp-p TVI(Transport Video Interface) 75 Ohms
Minimum Illumination	0.001 Lux @ F1.4(Sens-Up X32)
Shutter Speed	AUTO / Manual(1/25,1/30Sec ~ 1/30000Sec) / FLICKER
BLC	0
HSBLC	0
WDR(Wide Dynamic Range)	ON / OFF (Low,Middle,High) (15 Fram)

CAMERA DIMENSION

1) HTBIR1M

3.90° 3.25° 2.95°

4.80° 8.56°

General Features

● Transfer Video Interface

The combination of a 2Mega CMOS image sensor and TVI DSP provides an excellent resolution of TVI picture.

● 3D-DNR

Smart 3DNR prevents the image blurring of moving object and activates only if moving objects are appearing on the scene.

Smart-IR

No saturation image, vivid image in darkness! "TVI" camera makes very sharp video image in darkness! This technology eliminates saturation of video image of the closer object in darkness by control of the IR sensitivity. Saturation never happens in our "TVI" cameras, you can enjoy vivid image in any dark condition!

● Sens-Up

Despite a limited & low light condition, Sens-Up - Max. x32 helps the viewer to get visible and clear images.

- Defog

Defon function "improves" the clarity of images taken in poor conditions such as fog, smoke.

How to Set Up the camera menu

• Setup Menu

MENU
1. PRESET	INDOOR, OUTDOOR, LOWLIGHT, HALLWAY, LOOBY(WDR), ELEVATOR
2. MAIN SETUP
3. EXIT	EXIT / RESET(L/R-PUSHING)
MAIN SETUP		SUB MENU 1	SUB MENU 2	SUB MENU 3	SUB MENU 4
1. 2MOTOR		AF MODE	AUTO / MANUAL
		SCANNING	HALF / FULL
		ONE PUSH AF	ON
		SYNC TDN	ON / OFF
		INITIAL	ON
		RETURN
2. EXPOSURE		BRIGHTNESS	0~20
		SUTTER	AUTO
			MANUAL	SPEED	1/30 - 1/30000
				RETURN
			FLICKER
		INTENSIFY	OFF ~ X32
		AGC	0~20
		RETURN
3. WHITE BAL	AUTO
	AWB
	AWC-SET
	MANUAL	KELVIN	LOW / MIDDLE / HIGH
		R-GAIN	0~20
		B-GAIN	0~20
		RETURN

How to Set Up the camera menu

- Setup Menu

MENU
7. IMAGE		SHARPNESS	0~20
		GAMMA	0.45 - 0.65
		COLOR GAIN	0~20
		MIRROR	ON / OFF
		FLIP	ON / OFF
		ACE	OFF / LOW / MIDDLE / HIGH
		DEFOG	OFF
			ON	MODE	AUTO / MANUL
				LEVEL	LOW / MIDDLE / HIGH
				RETURN
		PRIVACY	OFF
			ON	ZONE NUM	0~15
				ZONE DISP	ON / OFF
				H-POS	0~60
				V-POS	0~34
				H-SIZE	0~60
				V-SIZE	0~34
				Y LEVEL	0~20
				CR LEVEL	0~20
				CB LEVEL	0~20
				RETURN
		RETURN
8. MOTION	OFF
	ON	SENSITIVITY	0~10
		WINDOW TONE	0~4
		WINDOW ZONE	0~3
		WINDOW USE	OFF/ON
		DEF 4 POS	1, 60

Menu Set Up

Menu items can be selected by using the OSD buttons of the camera.

1. PRESET

SPECO TECH ▶1. PRESET INDOOR 2.MAIN SETUP ← 3.EXIT

1-1. Preset : INDOOR / OUTDOOR / LOW LIGHT / HALLWAY / LOBBY(WDR) / ELEVATOR.
- Used for a quick and easy setup for the installation environment.
* The Advanced Set Up menu will be displayed on the monitor.
2. Move and select the required function using the Up and Down button.

1. Change menu settings using the Left or Right button.
   * Available values or Status are displayed by pressing the Left or Right buttons. Press the button until desired value / status is displayed.
2. After Changing the setting move the arrow indicator to EXIT and press the SET button to EXIT.

NOTE

* Move to the available submenu by moving ←arrow to desired feature.
* Submenu is not available when this symbol displayed "---".

2MOTOR

1. Move the triangular indicator to 2MOTOR using the Up and Down buttons on the Set Up menu screen.

1.2MOTOR AF MODE AUTO SCANNING HALF ONEPUSHAF ON SYNO TDN ON INITIAL ON RETURN ←

◆ AF MODE
- AUTO : Adjust zoom and focus automatically.
- MANUAL : Adjust zoom and focus manually.

◆ SCANNING : HALF / FULL

• HALF : Adjust auto focusing when lens focus fixed. If lens focus is not fixed well, adjust focus manually.
• FULL : Scanning full size of scree and adjust autofocusing.

◆ ONEPUSHAF : If you press OSD button 3\~4 seconds, focus will be fixed automatically.
◆ INITIAL : If you press OSD button 3\~4 seconds, Lens Initializing start.

EXPOSURE

1. Select the desired shutter mode by pressing the Left or Right button.

2. EXPOSURE BRIGHTNESS 9 AUTO SHUTTER INTENSIFY X16 AGC 20 RETURN

◆ BRIGHTNESS : The brightness can be adjusted. The brightness control range is 1\~20.
◆ SHUTTER : DC lens is launched with the setting of 1/30 and the manual lens is launched with the setting of Auto shutter, but the shutter speed can be adjusted from 1/30 to 1/30,000.

→ FLK : Select FLK mode if flickering occurs ; caused by the unmatched frequency of electric light.

INTENSIFY: The bright screen can be displayed by sensing the degree of the darkness automatically under the circumstance of low light condition or at night.

→ Off \~x32 Level Adjustable.

◆ AGC (Auto Gain Control) : The higher the AGC level is, the more noises appear.

→ 0\~20 Level selectable.

White Balance

Use this function when the color adjustment of a screen is needed.

1. Move the triangular indicator to WHITE BAL on the SETUP menu screen using the Up and Down button.
2. Select the desired mode by using the left or Right button.

MENU 1.2MOTOR 2.EXPOSURE 3.WHITE BAL AUTO 4.BACKLIGHT OFF 5.SPECO DNR MIDDLE 6.DAY&NIGHT AUTO 7.IMAGE 8.MOTION ON 9.SYSTEM 10.RETURN

◆ AUTO : Use this mode when the color temperature is from 2,500k to 9,500k.
◆ AWB : The function to search for the color which is matched well with the ambient environment.
◆ AWC→SET : After letting camera focus on the blank white paper to the best condition of current

NOTE

The White Balance may not be worked properly in the following conditions. If this doesn't work, use the AWB mode.

* When there is a very high color temperature in the circumstances of the subject. (for example, clear sky, Sunset)
* It is very dark.
* If the camera is headed to the fluorescent light directly or if there is a drastic lighting change, The operation of White balance may become unstable.

BACKLIGHT

On this menu, backlight image can be compensated by users selecting one of modes. (HLC, BLC, WDR)

1. Move the triangular indicator to BACKLIGHT on the SETUP menu screen using the Up and Down button.
2. Select the desired mode by using the left or Right button.

MENU

HLC LEVEL MODE RETURN 10 |||||||||||||||| ALL DAY

◆ BLC : This function is used to counterbalance the screen image by increasing the brightness so that a subject which appears dark due to a strong backlight can be displayed in more detail. If you select BLC, a submenu appears where you can make finer adjustments.

- H-POS/V-POS/H-SIZE/V-SIZE : Define the position and size of the area of interest by changing the position & size.

BLC H-POS 8 V-POS 7 H-SIZE 3 V-SIZE 3 RETURN

SPECO DNR

This function is used to improve the picture quality by filtering the noise which is generated under low brightness conditions. You can set different levels here.

1. Move the triangular indicator to SPECO DNR by using the Up and Down button.
2. Select the mode to use by pressing the left or Right button and OFF/LOW/MIDDLE/HIGH level selectable.

MENU 1.2MOTOR 2.EXPOSURE 3.WHITE BAL AUTO 4.BACKLIGHT OFF 5.SPECO DNR MIDDLE 6.DAY&NIGHT AUTO 7.IMAGE 8.MOTION ON 9.SYSTEM 10.RETURN

Day&Night

◆ AUTO : Automatically, It shifts into the color mode in the bright environment and the B/W mode in the low light condition. It can adjust the delay time, starting brightness and end brightness according to the ambient conditions by pressing the Set button.

6. DAY&NIGHT SMART IR. 2 AGC THRES 2 AGC MARGIN 2 DELAY LOW RETURN ←

• SMART IR : 0\~20 Smart IR level adjustable.
• AGC THRES : 0\~20 AGC THRES level adjustable.
• AGC MARGIN : 0\~20 AGC MARGIN level adjustable.
• DELAY [LOW/MIDDLE/HIGH] : Set the delay time for switching between COLOR and B/W.

◆ COLOR : Making the video output color always.
◆ B / W : Making the video output B/W always.
- SMART IR : 0\~20 Smart IR level adjustable.
◆ EXTERN : It can change the color or B/W mode automatically through the connection with the ground terminal. (Option for box camera and IR camera)
- SMART IR : 0\~20 Smart IR level adjustable.

eVTTRN CAV FLOWINGUL, 641, 1000-1500, 1500-2000, colon - 1998

Here you can optimise the image quality by adjusting different options.

7. IMAGE SHARPNESS 11 GAMMA 0.5 COLOR GAIN 13 MIRROR OFF FLIP OFF ACE OFF DEFOG OFF PRIVACY OFF RETURN ←

◆ SHARPNESS [1 \~ 20] : Adjusts the image sharpness. If the level goes up excessively, it may affect the video image and generate a noise.
◆ GAMMA [0.45 \~ 0.65] : Changes the gamma curve of the camera.
◆ COLOR GAIN [0 \~ 20]: Changes the color gain of the camera.
◆ MIRROR [ON, OFF] : Mirrors the image horizontally on the screen.
▲ run (ou, or) rll.

PRIVACY ZONE NUM 0||||||||||||| ZONE DISP ON H-POS 12||||||||||||| V-POS 2||||||||||||| H-SIZE 3||||||||||||| V-SIZE 3||||||||||||| Y LEVEL 10||||||||||||| CR LEVEL 10||||||||||||| CB LEVEL 10||||||||||||| RETURN ←

• ZONE NUM [0\~15]: Select a mask out of the 16 mask areas and set the options below for the selected mask.
• ZONE DISP [ON, OFF] : Choose ON to activate privacy masks and press OFF to deactivate masks.
• H-POS [0\~60] : Define the horizontal start position of the privacy mask.
• V-POS [0\~34] : Define the vertical start position of the privacy mask.
• H-SIZE [0\~60] : Define the horizontal size of the privacy mask.
• V-SIZE [0\~34] : Define the vertical size of the privacy mask.
• Y LEVEL [0\~20] : Define the brightness of the mask color.
• CR LEVEL [0\~20] : Define the red amount of the mask color.
• CB LEVEL [0\~20] : Define the blue amount of the mask color.

MOTION SENSITIVITY 10 WINDOW TONE 4 WINDOW ZONE 3 WINDOW USE OFF DET H-POS 60 DET V-POS 34 DET H-SIZE 60 DET V-SIZE 34 ALARM OFF RETURN ←

◆ SENSITIVITY [0\~10] : The higher the setting value is, the higher the sensitivity gets, even though the movement of a subject.
◆ WINDOW TONE [0\~4] : Set out area tone of motion zone.
◆ WINDOW ZONE [0\~3] : Select the window area.
◆ WINDOW USE [ON, OFF]
◆ DET H-POS [0\~60] : Define the horizontal start position of the monitoring area.
◆ DET V-POS [0\~34] : Define the vertical start position of the monitoring area.
◆ DET H-SIZE [0\~60] : Define the horizontal size of the monitoring area.
◆ DET V-SIZE [0\~34] : Define the vertical size of the monitoring area.
◆ ALARM [ON, OFF] : In motion situation, you can select the detail of option setting.

9.SYSTEM COM. IMAGE RANGE USER FRAME RATE 1080_30P COLOR SPACE HD-Cbcr CVBS NTSC LANGUAGE ENG COLOR BAR OFF RESET ON RETURN

◆ COM.: This menu id used for RS-485 communication. Users are able to select 'CAM ID(0\~255)' and 'BAUDRATE(2400/4800/9600/57600/115200).

PROBLEM	POSSIBLE CAUSE
Nothing appears on the screen.	Check the power cable, power supply output and video connection between the camera and monitor.
The image on the screen is dim.	Are the camera lens or the lens glass dirty?Clean the lens / glass with a soft clean cloth.Adjust the monitor controls, as required.If the camera is facing a very strong light, change the camera position.Adjust the lens focus.
The image on the screen is dark.	Adjust the contrast control of the monitor.If there is an intermediate device, correctly set the 75Ω/Hz.
The camera is not working properly and the surface of the camera is hot.	Check the camera is correctly connected to an appropriate regulated power source.
Motion Detection is not activated.	Has MOTION DET been set to ON in the menu?Has MD AREA been properly defined?
The color of the screen is dark.	Check the settings in WHITE BALANCE menu.

LIMITED WARRANTY - VIDEO PRODUCTS

THIS WARRANTY IS VALID ONLY ON PRODUCTS PURCHASED AND USED IN THE UNITED STATES OF AMERICA AND CANADA. THIS WARRANTY APPLIES ONLY TO THE ORIGINAL USER.

SUBJECT TO CONDITIONS AND EXCLUSIONS FOUND BELOW, THIS PRODUCT IS WARRANTED AGAINST MANUFACTURING DEFECTS IN MATERIAL AND WORKMANSHIP FOR THE FOLLOWING PERIOD FOR PARTS AND LABOR:

SPECO TECHNOLOGIES CAMERAS .... 5 YEARS

SPECO TECHNOLOGIES IP CAMERAS.... 5 YEARS

SPECO PTZ AND VL CAMERAS.... 1 YEAR

SPECO TECHNOLOGIES MONITORS.... 1 YEAR

IR LEDS .... 90 DAYS

DVRs	5 YEARS
NVRs	5 YEARS
BALANCE OF
SPECO TECHNOLOGIES LINE	1 YEAR

SPECO TECHNOLOGIES WILL REPAIR OR REPLACE (AT OUR DISCRETION) ANY PARTS FOUND TO BE DEFECTIVE FOR THE WARRANTY PERIOD SPECIFIED. WE WILL PROVIDE A REPLACEMENT FOR ANY DEFECTIVE PART.

CONDITIONS

1. YOU MUST OBTAIN A RETURN AUTHORIZATION (RA) NUMBER FOR ANY MERCHANDISE BEING RETURNED TO SPECO TECHNOLOGIES, WHETHER FOR RETURN/EXCHANGE OR REPAIR, WHETHER IN OR OUT OF WARRANTY.

2. THIS WARRANTY WILL BE HONORED ONLY UPON PRESENTATION OF THE ORIGINAL DATED BILL OF SALE OR SALES SLIP.

3. TRANSPORTATION OF THE PRODUCT TO OUR SERVICE DEPARTMENT IS THE RESPONSIBILITY OF THE USER, REPAIRED OR REPLACED PRODUCT WILL BE RETURNED PREPAID DURING THE WARRANTY PERIOD.
4. SPECO TECHNOLOGIES DOES NOT AUTHORIZE ANY INTERNET OR MAIL ORDER PRODUCT SALES. IF A SPECO TECHNOLOGIES PRODUCT IS PURCHASED FROM AN UNAUTHORIZED DISTRIBUTOR OR OTHER SOURCE, INCLUDING RETAILERS, MAIL ORDER SELLERS AND ONLINE SELLERS, IT WILL NOT BE HONORED OR SERVICED UNDER THE EXISTING SPECO TECHNOLOGIES WARRANTY POLICY ANY SPECO TECHNOLOGIES PRODUCT PURCHASED FROM THESE ONLINE MERCHANTS WILL VOID THE APPLICABLE WARRANTY AND IS INELIGIBLE FOR TECHNICAL SUPPORT. IF YOU HAVE QUESTIONS ABOUT A RESELLER, PLEASE CONTACT SPECO TECHNOLOGIES AT 1-800-645-5516 FOR A LIST OF UNAUTHORIZED DEALERS, VISIT: www.specotech.com/unauthorized.

EXCLUSIONS

1. THIS WARRANTY SHALL NOT COVER ADJUSTMENT OF CUSTOMER OPERATED CONTROLS AS EXPLAINED IN THE APPROPRIATE Model's INSTRUCTION MANUAL OR PRODUCTS WHICH HAVE BEEN ALTERED, ABUSED, OR HAVE MISSING OR ALTERED SERIAL NUMBERS.
   2 TH'S WARRANTY SHALL NOT APPLY TO UNCRATING, SETUP, INSTALLATION, OR THE REMOVAL AND REINSTALLATION OF PRODUCTS AFTER REPAIR.
2. THIS WARRANTY SHALL NOT APPLY TO REPAIRS OR REPLACEMENTS NECESSITATED BY ANY CAUSE BEYOND THE RESULT OF MANUFACTURE INCLUDING, BUT NOT LIMITED TO, ANY MALFUNCTION, DEFECTS OR FAILURE CAUSED BY OR RESULTING FROM UNLIMITED SERVICE OR OTHER INFORMATION INFLUANCE, MODIFICATION OR REFORM BY THE USER ALICE, MOUNTED NOLOGY

speco technologies®