D16WRSM - Security Camera Speco Technologies - Free user manual and instructions

USER MANUAL D16WRSM Speco Technologies

Model: D4RS, D8RS, D16RS, D4WRS, D8WRS, D16WRS

4, 8, 16 Channel Digital Video Recorder

Exterior view of a beige rectangular box with a small circular button on the side (no text or symbols visible)

Cautions

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

Explanation of Graphical Symbols

This symbol indicates the presence of important operang and maintenance (servicing) instrucons in the literature accompanying the product.

This symbol indicates the presence of "dangerous voltage" within the product's enclosure that may be of sucient magnitude to constute a risk of electric shock, property damage, personal injury, or death.

These Precautions must be Followed for Safety Reasons

Warning

• Do not use if the unit emits smoke.
• Do not disassemble the unit.
• Do not place any heavy or sharp objects on the unit.
• Do not place on uneven surface.
• Do not expose to shock or vibration.
• Do not move the unit when the unit is powered on.
• Do not block, and allow dust to accumulate in the air vents.
• Do not restrict airflow of the unit; doing so can damage the unit.
• Only qualified and experienced personnel should perform installation and servicing.
• Turn off the power of the DVR when connecting Cameras, Audio or Sensor Cables.
• The manufacture is not responsible for any damage caused by improper use of the product or failure to follow instructions for the product.
• The manufacture is not responsible for any problems caused by or resulting from the user physically opening the DVR for examination or attempting to repair the unit.

Product Components

Please make sure the following components are included as specified below.

DVR Unit(D4WRS/D8WRS/D16WRS or D4RS/D8RS/D16RS)
Remote Control
Battery1.5V (AAA x 2EA)
Quick Start Guide

Specifications

ITEM				D4RS/D4WRS	D8RS/D8WRS	D16RS/D16WRS
Video	Input	Channel, Input Level		4CH/ 8CH/ 16CH Composite, 1.0Vp-p, 75ohm
		Signal Format		NTSC/PAL
		Video Loss Check		Yes
	Output	VGA		1 VGA (1024x768, 1280x1024)
		CVBS		1 BNC Selectable	1 BNC	1 BNC
		SPOT			1 BNC	1 BNC
Audio	Input & Output			4 CH Line input & 1 CH Line output
	Audio Codec			G.711
Sensor/ Alarm	Sensor Input			4 (NC / NO Selectable)
	Alarm Out			1 Alarm Out by Sensor, Motion and Video Loss
Record	Compression			H.264
	Multi-operation			QUADPLEX (Playback/Record/Network/Backup)
	Resolution	NTSC	D1	120fps	120fps	120fps
			Half D1	120fps	240fps	240fps
			CIF	120fps	240fps	480fps
		PAL	D1	100fps	100fps	100fps
			Half D1	100fps	200fps	200fps
			CIF	100fps	200fps	400fps
	Recording quality grade			LEVEL1 (L) ~ LEVEL5 (H)
	Recording Mode			Continuous/Schedule/Motion/Manual/Sensor
	Motion Detection			Motion detection setup by Grid
	Backup	USB Flash drive	Video & Still Image
		Network	Video & Still Image
		Huge Backup	Yes (up to 24 hours)
User I/F	Menu Display		GUI
	Input Method		Remote control, Mouse
RS-485	PTZ control		1 RS-485	1 RS-485	1 RS-485
Network	Dynamic DNS		Yes (Free DDNS)
	Network Interface		10/100 base-TX Ethernet (RJ-45)	10/100/ 1000 base-TX Ethernet (RJ-45)
	Max. Network Live Streaming		CIF 60fps/4CH	CIF 120fps/8CH	CIF 240fps/16CH
	Max. Network Playback Streaming		CIF 60fps/4CH CIF 30fps/1CH	CIF 120fps/8CH CIF 30fps/1CH	CIF 240fps/16CH CIF 30fps/1CH
Network Access	Web Viewer (1:1)		Live, Search, Backup, Remote Setup, PTZ control
	Mobile Phone Viewer (1:1)		Live, Search, PTZ control
	Multi-sites Monitoring SW (1:n)		Live, Search, Backup, Remote Setup, PTZ control
Features	DLS (Day Light Saving)		Yes
	EZSearch (Thumbnail Search)		Yes
	EZRecord		Yes
	EZCopy		Yes
	S.M.A.R.T		Yes
	Internal Beep		By Video Loss, HDD Error, S.M.A.R.T
	Multi-Language		Yes
	S/W Upgrade		USB Flash drive, Remote S/W Upgrade
	NTP		Yes
	Multi-Language		Yes

Table of Contents

1. Main Features 10
2. Initial Boot up Process....11
   2-1. Initial Boot up and Basic Time Setup 11
   2-2. Setting Daylight Saving Time....11
   2-3. Setting NTP (Network Time Protocol) 12
3. Name, Function and Connection 15
   3-1. Front Panel....15
   3-2. Connectors....15
   3-3. Remote Control....17
4. Setting up the DVR....18
   4-1. Setup – Main Live Screen....18
   4-2. Setup - SYSTEM Mode 19
   4-3. Setup - RECORD Mode 23
   4-3-1. Recording Schedules 25
   4-4. Setup - DEVICE Mode 26
   4-4-1. Alarm-Out....27
   4-4-2. Keyboard Controller & PTZ Setup 28
   4-4-3. Spot Out....29
   4-4-4. Motion Zone Setup....30
   4-5. Setup - DISPLAY Mode 31
   4-6. Setup - NETWORK Mode 33
   4-6-1. Network Types ....34
   4-6-2. DDNS....34
   4-6-3. Network Port and Web Port....35

5-3-6. Go To Specific Time....50
5-3-7. Archive List....50
5-3-8. Log List 51
5-4. Play Mode 51
6. Back Up....52
6-1. Still Image Backup onto USB Flash Drive 52
6-2. Video Backup onto USB Flash Drive during playback....53
6-3. EZCopy: Video Backup onto USB Flash Drive during playback....54
6-4. Transferring Still Images or Video from the ARCHIVE List 55
6-5. Playback of Backup Video 56
6-5-1. AVI Format 56
6-5-2. NSF Format....56
7. Network Access Using the Multi-Sites Network Viewer 57
7-1. Overview 57
7-2. PC Requirements....57
7-3. Installation of the Program....58
7-4. Live Window....59
7-4-1.Main User Interface....59
7-4-2. Control Buttons ....59
7-5. Search and Playback Window 61
7-5-1.Main User Interface....61
7-5-2. Main Control Panel....61
7-6. Setup of SpecoTech Multi Client 63
7-6-1. General 63
7-6-2. Event....64
7-6-3. Record 65

7-8-3. Still-image Capture During Live 77
7-8-4. Recording Video on Local PC During Live....78
7-8-5. Local Playback and Remote Playback....79
7-8-6. AVI Backup during Playback....81
8. Network Access Using the Web-Browser Viewer.... 83
9. Network Access Using the Smart Phone Viewer 85
9-1. App Viewer for iPhone 85
9-1-1. Live 85
10-3-2.PTZ Control....86
10-3-3. Playback 86
9-2. App Viewer for Android Phone 87
9-2-1. Live 87
9-2-2.PTZ Control....88
APPENDIX: Network Connection - LAN 89
APPENDIX: Network Connection – Internet and DDNS....91
APPENDIX: E-SATA CONNECTION 94

1. Main Features

■ Easy Record, Copy and Setup
■ Easy Search by Thumbnail Preview
■ Easy Copy
■ Recording Rate: 120fps @ D1
■ H.264 high quality compression saves HDD space
■ Simultaneous live view/playback while continuing to record/network transfer or backup
■ Remote monitoring/recording/playback/configuration and control via internet
■ 4 Channel Audio Recording

NOTE: Under federal law, The Fourth Amendment to the U.S. Constitution, Title III of the Omnibus Crime Control and Safe Streets Act of 1968, as amended by the Electronic Communications Privacy Act of 1986 (18 U.S.C. § 2510, et seq.), and the Foreign Intelligence Surveillance Act of 1978 (50 U.S.C. 1801, et seq.) permit government agents, acting with the consent of a party to a communication, to engage in warrantless interceptions of telephone communications, as well as oral and electronic communications.

■ Automatic camera detection (Plug & Play)
■ Covert camera operation provides enhanced security and administrator control
■ Dynamically programmable recording priority, motion detection, alarms and scheduling
■ Simple and Easy Graphic User Interface
■ Simple Scheduler
■ VGA Output
■ Password to secure installation authorization
■ Network software supports 10/100Mbps
■ USB 2.0 port for video clip exporting and easy firmware upgrade via USB Flash Drive
■ Exclusive File Format Backup and Player

2. Initial Boot up Process

2-1. Initial Boot up and Basic Time Setup

1. During the first boot up, the following logo and message will be displayed.

speco technologies

Initializing system It may take a few seconds or minutes to check system. 0% Initializing...

1. After the system initializing is completed, select the language and set date and time as specified below.

Choose language. ENGLISH CLOSE Set date and time SET DATE & TIME 2011 / 3 / 8 16 / 0 / 0 CLOSE

2-2. Setting Daylight Saving Time

LOGIN - SETUP USER ADMIN PASSWORD OK CANCEL

1. Go to SETUP > SYSTEM > DATE & TIME SETUP

SYSTEM DESCRIPTION LANGUAGE DATE DISPLAY FORMAT DATE & TIME SETUP CLIENT ACCESS NTP SETLP SEND EMAIL SETUP UNIT NAME ENGLISH YYYY/MM/DD ON OFF OFF DVR APPLY CLOSE

1. Select ON from the DAYLIGHT SAVING dropdown menu.

DAYLIGHT SAVING OFF SET DATE & TIME 2011 / 8 / 8 16 / 0 / 0 OK CANCEL

2. Select the proper TIME ZONE time.

PRIMARY SNTP SERVER Pool.ntp.org SECONDARY SNTP SERVER Time.nist.gov TIME ZONE GMT +0:00 (Lisbon/London/Monaco) CONNECTION MODE TIME CONNECTION PERIOD 03:00 AM OK CANCEL

Table2.3.1. GMT Time Zone

	State	Standard Time	Daylight-Saving Time
AL	Alabama	GMT-6	GMT-5
AK	Alaska	GMT-9	GMT-8
AK	Alaska (Aleutian Islands)	GMT-10	NA
AZ	Arizona	GMT-7	NA
AZ	Arizona (Navajo)	GMT-7	GMT-6
AR	Arkansas	GMT-6	GMT-5
CA	California	GMT-8	GMT-7
CO	Colorado	GMT-7	GMT-6
CT	Connecticut	GMT-5	GMT-4
DC	District of Columbia	GMT-5	GMT-4
DE	Delaware	GMT-5	GMT-4
FL	Florida	GMT-5	GMT-4
FL	Florida (W)	GMT-6	GMT-5
GA	Georgia	GMT-5	GMT-4
HI	Hawaii	GMT-10	NA
MI	Michigan (W)	GMT-6	GMT-5
MN	Minnesota	GMT-6	GMT-5
MS	Mississippi	GMT-6	GMT-5
MO	Missouri	GMT-6	GMT-5
MT	Montana	GMT-7	GMT-6
NE	Nebraska	GMT-6	GMT-5
NE	Nebraska (W)	GMT-7	GMT-6
NV	Nevada	GMT-8	GMT-7
NH	New Hampshire	GMT-5	GMT-4
NJ	New Jersey	GMT-5	GMT-4
NM	New Mexico	GMT-7	GMT-6
NY	New York	GMT-5	GMT-4
NC	North Carolina	GMT-5	GMT-4
ND	North Dakota	GMT-6	GMT-5
ND	North Dakota (W)	GMT-7	GMT-6
OH	Ohio	GMT-5	GMT-4
OK	Oklahoma	GMT-6	GMT-5
OR	Oregon	GMT-8	GMT-7
OR	Oregon (E)	GMT-7	GMT-6
PA	Pennsylvania	GMT-5	GMT-4
RI	Rhode Island	GMT-5	GMT-4
SC	South Carolina	GMT-5	GMT-4
SD	South Dakota (E)	GMT-6	GMT-5
SD	South Dakota (W)	GMT-7	GMT-6
TN	Tennessee (E)	GMT-5	GMT-4

3. Name, Function and Connection

3-1. Front Panel

DxxRS DxxWRS

Figure 3.1.1. Front panel

Table 3.1.1. Front LED and Port of DxxRS

Name	Description
POWER	LED light is on when power is applied to the system

AUDIO VIDEO IN AUDIO VIDEO OUT FIRIERNET USB DATA POWER

D8RS/D8WRS

AUDIO VIDEO OUT 1 2 3 4 5 6 7 8 9 10 11 AUDIO VOLUME WIDE ETHERNET USB - DATA POWER

D16RS/D16WRS
Figure 3.2.1. Connectors

① VIDEO IN: Video input port.
② VIDEO OUT:

D4RS: Switchable (Composite Video Output or Spot Monitor)

D8RS, D16RS: CVBS1 - Composite Video Output / CVBS2 - Spot Monitor

③ VGA: VGA (Video Graphics Array) output port. Connects to the PC VGA monitor.
④ RS-232C (for D8RS/D16RS/D8WRS/D16WRS only): For engineering use only, the function is used by a gender through the VGA output.
⑤ AUDIO IN: Four connectors for audio input. D8RS/D16RS/D8WRS/D16WRS use an audio cable
⑥ AUDIO OUT: One connector for audio output. D8RS/D16RS/D8WRS/D16WRS use an audio cable.
⑦ ETHERNET: Network terminal

3-3. Remote Control

Diagram of a remote control with numbered buttons and function keys on the right side

Typical Remote Control

① ID: To set the remote control ID.
② REC: To start and stop manual recording
③ 0\~9: To select channel (1,2,3,...) or to enter a DVR ID number or use as number key.
④ F/REW:
- During playback – To move the playback position 60 seconds back.
- During Pause – To move the playback position 1 frame back.
⑤ F/ADV:
- During playback – To move the playback position 60 seconds forward.
- During Pause – To move the playback position moves 1 frame forward
⑥ REW: To rewind the recording.
⑦ PLAY/PAUSE: To play or to pause the recording in playback mode
⑧ FF: To fast forward the recording.
(a) Direction buttons: To move menu items or select a channel

4. Setting up the DVR

The following sections detail the initial setup of the DVR.

Menu screen will close if user input is not received in 5 minutes.

4-1. Setup - Main Live Screen

To enter the setup menu, right click on the mouse and select setup from the submenu or press the setup button on the remote control.

CH 1 C CH 2 VIDEO LOSS SETUP AUDIO 2 SEARCH SNAPSHOT CAMERA PTZ MAIN MONITOR SEQUENCE ON MANUAL RECORD ON ALARM OUT OFF CH 3 VIDEO LOSS SITE INFORMATION SYSTEM INFORMATION SYSTEM LOCK SYSTEM SHUTDOWN CH 4 VIDEO LOSS

4-2. Setup - SYSTEM Mode

In the SETUP menu, select the SYSTEM tab. Then, the SYSTEM menu is displayed as pictured below.

Navigate through the menu items using the mouse or the remote control and change the value of the menu.

SYSTEM DESCRIPTION LANGUAGE DATE DISPLAY FORMAT DATE & TIME SETUP CLIENT ACCESS NTP SETUP SEND EMAIL SETUP UNIT NAME ENGLISH MM/DD/YYYY ... ON ON ON SPECO RS4 APPLY CLOSE

Figure 4.2.1. SYSTEM Setup Screen
Table 4.2.1. Menu Items in SYSTEM Setup Screen

DATE&TIME SETUP

Select the display date and time using the mouse or the control button on the remote control and press OK button to set the present date and time.

DAYLIGHT SAVING USA SET DATE & TIME 2011 / 11 / 2 16 : 46 : 13 OK CANCEL

Select DAYLIGHT SAVING using the mouse and the control button on the remote control and select the appropriate daylight saving time zone. The options are:

OFF: Daylight saving is turned off.

USA: Applies the USA daylight saving time.

EU: Applies the EU daylight saving time.

• Select the GMT AREA using the mouse or the control button.
• Set the time difference with the standard time using the mouse or the button.

OTHERS: If the time zone is neither USA nor EU, set the date and time of the daylight saving period.

- Select BEGIN or END using the control button and press the SEL button.

Caution

• Do not set the start time to 23:00 for DLS.
• DLS cannot be applied if the date of BEGIN and END is the same.

CLIENT ACCESS

Enable/Disable remote access through the network.

NTP SETUP

NTP (Network Time Protocol) which synchronizes the time of the computer systems over variable-latency data networks.

• INTERVAL – Every 1 hour \~ 24 hours
• ONCE - Synchronizes time only once. NTP will not synchronize unless the Connection Mode is changed.

DVR sends E-MAIL Notification when the NTP server time is faster than the system time with bellow message.

"NTP server time is faster than the system time.

In this case, NTP server time is ignored to protect the user data.

User must set the time manually.

SYSTEM TIME: Mon Oct 10 13:46:49 2011

SERVER TIME: Mon Oct 10 13:33:12 2011

DVR ID: DVR

IP ADDRESS: 172.16.2.46"

SEND EMAIL

TRANSMISSION MODE IP NOTIFICATION MAIL BY MOTION MAIL BY VIDEO LOSS MAIL BY S.M.A.R.T. MAIL DVR STATUS MAIL PORT SECURE OPTION MAIL TO MAIL SERVER ID PASSWORD

PERIOD DAILY FIRST SUN 0 H OK CANCEL

MAIL PORT: Assign Mail Port number.

SEURE OPTION: Select the secure mail server connection method. (SSL or TLS)

MAIL TO: Enter the appropriate email address to enable sending e-mail reports using a virtual keyboard.

MAIL SERVER: Enter the appropriate mail server information.

ID: Enter the appropriate mail server ID.

PASSWORD: Enter the appropriate mail server PASSWORD.

MAIL FROM: To set the email address sent to the destination host.

UNIT NAME

Name the DVR (e.g. Factory)

This feature is to identify the name of the DVR under the same network.

4-3. Setup - RECORD Mode

In the SETUP menu, select the RECORD tab. Then, the RECORD menu is displayed as pictured below. Navigate through the menu items using the mouse or the control button on the remote control and change the value of the menu item.

RECORD SITE CH 1 RESOLUTION D1 FRAME RATE 6 FPS QUALITY LEVEL 5(H) RECORDING MODE MOTION SENSOR RECORDING PRE RECORD 1 MINUTE(S) POST EVENT RECORD 10 SECOND(S) AUDIO OFF SCHEDULE ... EZRecord ... APPLY CLOSE

Figure 4.3.1. RECORD Setup Screen

RESOLUTION	Select D1, Half D1 or CIF using the mouse or the control button on the remote control.
FRAME RATE	Set the frame rate for the specified channel. The sum of the frame rate values from each channel cannot exceed the maximum frame rates for a specific recording resolution.
QUALITY	Select the recording quality for the selected channel. Options are;Level 1 (Low), Level 2, Level 3, Level 4, and Level 5 (High)
RECORDING MODE	Assign the recording mode for the selected channel. Options are: Continuous,Motion, Schedule or Disable.
SENSOR RECORDING	Select the sensor setting for the selected channel.
PRE RECORD	Enable/disable pre-event recording. Pre-event recording time is up to 20 minutes.
POST EVENT RECORD	Set the post event recording time duration for the specified channel.(10~30 seconds)
AUDIO	Enable/disable audio recording for the specified channel.
SCHEDULE	Set the recording schedule.
EZRECORD	Set the recording by EZRecord feature.The EZRECORD has high priority than other setting values on RECORD.User can change the setting value such as resolution, frame rate, quality and recording type. By the setting value, the DAYS TO RECORD will change accordingly.

RESOLUTION	CIF
FRAME RATE	1 FPS
QUALITY	LEVEL 1(L)
RECORDING	CONTINUOUS

4-3-1. Recording Schedules

To setup a recording schedule, select SCHEDULE in the RECORD menu. Navigate through the items using the mouse or the control button.

Select CHANNEL > select NONE, CONTINUOUS or MOTION > HIGHLIGHT AREA

To copy a schedule to a different channel, select the channel from the COPY SCHEDULE menu.

CHANNEL 1 NONE CONTINUOUS SENSOR CLEAR 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 SUN MON TUE WED THU FRI SAT COPY SCHEDULE CH 1 CH 2 CH 3 CH 4 ALL COPY OK Cancel

Figure 4.3.2. Schedule Recording Setup Screen

• NONE: Disable recording
  • CONTINUE: CONTINUOUS recording (Highlighted in Green)
  • MOTION: MOTION recording (Highlighted in Yellow)

4-4. Setup - DEVICE Mode

In the SETUP menu, select the DEVICE tab. Then, the device menu is displayed as pictured below. Navigate through the menu items using the mouse or the control button on the remote control and change the value of the menu item.

DEVICE ALARM-OUT CONTROLLER & PTZ SPOT-OUT SITE MOTION ZONE MOTION SENSITIVITY KEY TONE REMOTE CONTROLLER ID SENSOR TYPE CH 1 FULL ZONE 9 OFF 0 1 OFF APPLY CLOSE

Figure 4.4.1. DEVICE Setup Screen

	(9 – Highest sensitivity, 1 – Lowest sensitivity)
KEY TONE	Enable/disable key tone.
REMOTE CONTROL ID	Set the remote control ID.1. Select ID.2. Input the remote control ID number.3. An icon will indicate on the Live Screen if the remote control ID is synchronized.The options are from 0 to 99
SENSOR	Select the type of each sensor.Option is Off, Normal Open or Normal Close.

4-4-1. Alarm-Out

ALARM-OUT SENSOR IN MOTION ON VIDEO LOSS ON ALARM DURATION ERROR ALARM 1 - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -

Figure 4.4.2. ALARM-OUT Setup Screen

4-4-2. Keyboard Controller & PTZ Setup

To control the PTZ functions of the camera, connect the PTZ controller to the RS-485 port on the back of the chassis with CAT5 (or equivalent) cable.

① Connect the RS-485 cables of PTZ camera to the RS-485 port on the rear panel.

Sensor Inputs S1 D20 S3 A D+ Alarm Output RS-485 D+ RS-485 D- S2 D20 S4 B D- [S4RS/D4WRS] Sensor Inputs S1 S2 S3 S4 D+ Alarm Out RS-485 D+ RS-485 D- [S8/16RS, D8/16WRS]

Figure 4.4.3. Device Mode Setup Screen

DEVICE ALARM-OUT CONTROLLER & PTZ SPOT-OUT SITE MOTION ZONE MOTION SENSITIVITY KEY TONE REMOTE CONTROLLER ID SENSOR TYPE CH 1 FULL ZONE 9 OFF 0 1 OFF

Note: Connect PTZ cameras that support RS-485 directly to the RS-485 port. If the camera is controlled through an RS-232C interface, use an RS-232C to RS-485 to RS-232C signal converter.

Use the PTZ setup screen to select the following options for the camera PTZ controller:

• CHANNEL: Channel connected to a PTZ device
• CAMERA: Protocol Type
• SPEED: 19200, 14400, 9600, 4800, 2400 (Baud rate)
• ID: 0-63

Controller (Keyboard Controller): If a PTZ controller is used, select a controller protocol from Controller menu. Set SPEED (Baud Rate) and ID number.

CONTROLLER SPEED ID CHANNEL CAMERA SPEED ID VC PROTOCOL WTX-1200A 9600 OK CANCEL

Figure 4.4.6. Controller Selection Screen

4-4-3. Spot Out

SPOT ON EVENT OFF SPOT EVENT DWELL TIME 3 SECOND(S) SEQUENCE OFF

SPOT EVENT	Set the dwell time for the display of the event activated channel.
DWELL TIME	(1-10sec)
SEQUENCE	Enable/disable sequential display of spot channel in full screen.If select ON, the selected channel will be displayed on the monitor periodically.
SEQUENCE	Set the dwell time for the spot channel display.(1-10sec)
DWELL TIME
SPOT CHANNEL	Select a channel for spot monitoring using the mouse or the control button on the remote control and press OK button.

4-4-4. Motion Zone Setup

Select MOTION ZONE using the mouse or the control button on the remote control and select either PARTIAL ZONE or FULL ZONE using the mouse control. The default value is FULL ZONE.

If FULL ZONE is selected, the motion zone grid screen is not displayed. Only set the level of sensitivity for MOTION SENSITIVITY.

FULL ZONE: The motion sensor is active on the whole screen.

PARTIAL ZONE: The motion sensor is active in the set detection frame.

Select the motion detection position using the mouse or the control button on the remote control. Then left click on the mouse or left click and drag the mouse pointer to select or deselect the area. Highlighted area indicates the partial motion detection zone. Press the ESC button or right click on the mouse to return to the previous menu.

Interior ceiling view of a building with exposed beams and structural elements (no visible text or symbols)

4-5. Setup - DISPLAY Mode

In the SETUP menu, select the DISPLAY tab. Then, the DISPLAY menu is displayed as pictured below. Navigate through the menu items using the mouse or the control button on the remote control and change the value of the menu item. To return to the previous setup menu screen, press the ESC button.

DISPLAY OSD ON OSD CONTRAST 100 MAIN MONITOR SEQUENCE ON SEQUENCE-DWELL TIME 3 SECOND(S) SITE CH 1 NAME CH1 COVERT OFF BRIGHTNESS 50 CONTRAST 40 HUE 50 SATURATION 50 VIDEO OUTPUT (VGA) ... APPLY CLOSE

Figure 4.5.1. DISPLAY Setup Screen

COVERT

Enable/disable display of the specified video channel in live display.

VIDEO OUTPUT (VGA)

D4RS/D4WRS

When VGA REOSLUTION is set at 1024 x 768.

• CVBS OUTPUT(Simultaneous Video Output): ON
- SPOT OUTPUT: OFF

When VGA RESOLUTION is set as 1280 x1024.

• CVBS OUTPUT(Simultaneous Video Output): OFF
- SPOT OUTPUT: ON

VGA RESOLUTION 1024 x 768 CVBS OUTPUT ON SPOT OUTPUT OFF OK CANCEL

D8RS/D16RS/D8WRS/D16WRS

CVBS1: Composite Video Output

CVBS2: Spot-Out port

4-6. Setup - NETWORK Mode

Select the NETWORK tab. Then, the network menu is displayed as pictured below. Navigate through the menu items using the mouse or the control button on the remote control and change the value of the menu.

NETWORK NETWORK TYPE IP 172.16.2.63 SUBNET MASK 255.255.0.0 GATEWAY 172.16.1.254 DNS (PRIMARY) 172.16.1.254 DNS (SECONDARY) DDNS ... NETWORK PORT 5445 NETWORK AUDIO PORT 5446 WEB PORT 80 NETWORK STREAM ... APPLY CLOSE

Figure 4.6.1. NETWORK Setup Screen

Table 4.6.1. Menu Items in NETWORK Setup Screen

Item	Description

NETWORK TYPE

DHCP·DVR will automatically retrieve an IP address

WEB PORT	Enter the port number for connection using web.
NETWORK	Set the value for network streaming.
STREAM

4-6-1. Network Types

4-6-1-1. DHCP

An IP address is automatically assigned by the DHCP server, which automatically assigns the IP address and other parameters to new devices.

4-6-1-2. STATIC

IP address, Subnet Mask, Gateway, and DNS are manually assigned by the user.

• IP ADDRESS: The fixed IP address of the DVR unit.
- SUBNET MASK: The subnet mask for the LAN.
• GATEWAY: The IP address of the Gateway.
• DNS (PRIMARY) The primary address of Domain Name Server
• DNS (SECINDARY): The secondary address of Domain Name Server

NOTE

Unless DNS is properly set, the DDNS and the e-mail features will not work.

4-6-2. DDNS

DDNS (Dynamic Domain Name System) allows a DNS name to be constantly synchronized with a dynamic IP address. It allows using a dynamic IP address to be associated with a static domain name

HOST NAME	This item allows the user to setup a domain name manually using virtual keyboard displays as shown.
SUBMIT/UPDATE	When manual host name input is done, move the cursor to this item and select ON to submit the settings.
ezDDNS	Enable/disable ezDDNS to register the host name automatically.

4-6-3. Network Port and Web Port

Connecting DVR/DVRs through an IP sharing device, each DVR must be assigned a unique TCP port number for access from outside the LAN. This port number is displayed on NETWORK>NETWORK PORT Setup MENU.

NOTE

If you access the DVR only within the same LAN, the TCP port number does not need to be changed.

Network access beyond a router

To access DVR beyond a router (firewall), you must open the proper TCP ports for live/playback streaming, for commands, for remote backup, and for audio streaming. If these ports are not opened properly, you can't access the DVR beyond a router.

For live/playback streaming, for commands, for remote backup: Open the port number on NETWORK>NETWORK PORT menu. The default port number is 5445.
For bi-directional audio: Open the port number on NETWORK AUDIO PORT. The default port number is [NETWORK PORT number + 1].
For web-viewer downloading and remote firmware upgrading: Open the port number on NETWORK>WEB PORT menu. The default port number is 80.

4-6-4. Network Stream

User can set the RESOLUTION, FRAME RATE, and the QUALITY for the network stream.

- D4RS: Up to 60 fns @CIF for 4 channels

4-7. Setup - USER MANAGEMENT Mode

In the SETUP menu, select the USER MANAGEMENT tab. Then, the USER MANAGEMENT menu is displayed as pictured below. Navigate through the menu items using the mouse or the control button on the remote control and change the value of the menu item.

USER MANAGEMENT AUTHORITY SETUP PASSWORD SETUP AUTHORITY OF PLAYBACK ... ... ... ... APPLY CLOSE

Figure 4.7.1. USER MANAGEMENT Setup Screen
Table 4.7.1. Menu Items in USER MANAGEMENT Setup Screen

	PASSWORD	SETUP	PB	R/OFF	NETWORK
PASSWORD CHECK		☒	☒	☒	☒
ADMIN	1111	☒	☒	☒	☒
USER1	1111	☒	☒	☒	☒
USER2	1111	☒	☒	☒	☒
USER3	1111	☒	☒	☒	☒

ADMIN, USER1, USER2, USER3:

Selected Checkbox: The user can access the function.

Blank Checkbox: The user can not access the function.

PASSWORD SETUP

Options are ADMIN, USER1, USER2 and USER3.

Select USER PASSWORD using the mouse or the control button on the remote control and press SEL button. Select user type and enter the current password. And, enter a new password, enter the same password again to confirm and select OK. Then the message "PASSWORD CHANGED" is displayed.

The factory default password is 1111.

It is highly recommended to assign a new password to protect the system.

AUTHORITY OF PLAYBACK

Set authority level of playback on each user.

Checked box: authorized to playback. Blank check box: no authority.

	1	2	3	4
ADMIN	#	#	#	#
USER1	#	#	#	#
USER2	#	#	#	#
USER3	#	#	#	#

STORAGE OVERWRITE ON DISK FORMAT ... DISK INFO ... RECORDING LIMIT OFF 30 DAYS RECORDING LIMIT DAYS ... S.M.A.R.T ... APPLY CLOSE

Figure 4.8.1. STORAGE Setup Screen

Table 4.8.1. Menu Items in STORAGE Setup Screen

Item	Description
OVERWRITE	When enabled, the DVR will continue recording and overwrite the oldest existing recorded data once the hard drive is full. When disabled, recording will stop once the hard drive is full.

DISK INFO Hard drive information. Displays the following information; HDD SIZE : 435 GB (FREE : 311 GB) HDD LAST TIME : 07-12-2011 16:41:00 Model Name Temperature Health (Good/Normal/Bad) HDD 1 HDD AAABBB1234567890 46 ℃ (114 ℉) Good OK DETAIL

RECORDING LIMIT	Enable/disable recording limit.
RECORDING LIMIT DAYS	Set the recording limit days. (1- 90 days)If the RECORDING LIMIT DAYS are set to 1, the data will be overwritten after 24 hours.
S.M.A.R.T	Set the alarm and beep by setting the HDD temperature limit.Alarm will trigger alarm output.Buzzer will trigger beeping from the internal speaker.

4-9. Setup - CONFIG Mode

In the SETUP menu, select the CONFIG tab. Then, the configuration menu is displayed as pictured below. Navigate through the menu items using the mouse or the control button on the remote control and change the value of the menu item.

CONFIG EXPORT TO USB IMPORT FROM USB LOAD DEFAULT LOAD FACTORY DEFAULT SOFTWARE UPGRADE ... ... ... ... ... ... ... APPLY CLOSE

Figure 4.9.1. CONFIGURATION Setup Screen

LOAD DEFAULT

Are you sure to save config to USB? YES NO

Press the button to reset the system to the default settings.

WARNING! Are you sure to load default config? If YES, system will restart.

The following settings such as Language, DVR ID, Security User Authentication, Security User P/W, Date format, DLS settings, Network settings, HDD overwrite, Limit recording, HDD serial number, and HDD ERROR time will not be included.

LOAD FACTORY DEFAULT

Press the button to reset the system to the factory default settings.

WARNING! Are you sure to load factory default config? If YES, system will restart

4-9-1. Firmware Upgrade

1. Create a new folder named "upgrade" in the USB flash drive root directory.

2. Create sub-folder for each model under "upgrade" folder and copy each firmware.

3. "d4rs" for D4RS and D4WRS: "main_D4RS_speco_***_201****"

4. "d8rs" for D8RS and D8WRS: "main_D8RS_speco_.*.*_201****"
5. "d16rs" for D16RS and D16WRS: "main_D16RS_speco_.*.*_201****"

Computer - 10.0 KB (57) - folder C:\Users\ folder Name Data modified Type Data Dogs 12/23/2018 001-004 No factor Dogs 12/23/2018 001-004 No factor Dogs 12/24/2018 029-004 No factor 3 items

1. Plug in the USB flash drive on the rear panel.
2. Navigate to CONFIG menu of SETUP.
3. Select SOFTWARE UPGRADE.
4. Follow the procedure from Figure 4.9.2 to Figure 4.9.4.

CURRENT SOFTWARE Ver 3.2.1 (07/13/2011) 0% SCAN CANCEL

Figure 4.9.2

CURRENT SOFTWARE Ver 3.2.1 (07/11/2011) USB CHECK Found USB MOUNT Ok FILE CHECK main.bin 5% UPGRADE CANCEL

Figure 4.9.3

5. Live, Search and Playback

5-1. Live View

In the Live screen, video inputs from the cameras are displayed as they are configured in the Display Setup screen. Various On-Screen Display (OSD) symbols, which indicate the status of the DVR, are described in Table 5.1.1.

CH 1 - C CH 2 VIDEO LOSS SETUP AUDIO 2 SEARCH SNAPSHOT CAMERA PTZ MAIN MONITOR SEQUENCE ON MANUAL RECORD ON ALARM OUT OFF CH 3 VIDEO LOSS SITE INFORMATION SYSTEM INFORMATION SYSTEM LOCK SYSTEM SHUTDOWN 07/07/2011 12:34:56 CH 4 VIDEO LOSS RC: ALL 0%

Figure 5.1.1. Live Screen and Quick Operation Window

	Indicates that a network client is connected to the DVR.
	Indicates that sequencing mode is enabled.
2009/04/14 17:23:40	Displays the current date and time.
RC: ALL	Remote control ID display. If a remote ID is not set, the message “ALL” is displayed.
15%	Displays the amount of recording on the hard disk from 0-99%.
	Indicates that HDD is recycled.
	Continuous recording in progress.
	Manual recording in progress. To set the Manual recording mode, press the Record button on the front panel.
	Motion alarm recording in progress.
	Sensor recording in progress. (Only for D8RS and D16RS model.)

Right click the mouse, and the quick operation window will be displayed as below.

Table 5.1.2. Menu Items in Quick Operation Window

Icon	Description
SETUP	Setup button. Click this button to go to a setup menu.
AUDIO	Audio button. Click this button to set an audio reception type; (Channel 1 through 4, Audio Mute).
SEARCH	Search button. Click this button to enter the search menu.
SNAPSHOT	Snapshot button. Click this button to create a snapshot. (JPEG STILL IMAGE)
CAMERA PTZ	Pop up the PTZ user interface.
MAIN MONITOR SEQUENCE ON/OFF	Sequence button. Click this button to use a sequence function.
MANUAL RECORD ON/OFF	Manual Record button. Click this button to enable manual recording.
ALARM OUT ON/OFF	Click this button to enable/disable Alarm outputs
SITE INFORMATION	Press the button to view the record setting of a selected channel.

5-1-1. PTZ Control

Table 5.1.3. Menu Items in PTZ Control Window

Item	Description
INITIALIZE	Initialize the PTZ settings of the selected camera
PAN/TILT	Select PAN/TILT using the ▲▼◀ and ▶button, then press SEL. Adjust the tilt (UP/DOWN)/pan (LEFT/RIGHT) position using the ▲▼◀and ▶buttons.
ZOOM/FOCUS	Select ZOM/FOCUS using the▲▼◀ and ▶buttons, then press SEL. Adjust the zoom (UP/DOWN)/ focus (LEFT/RIGHT)position using the ▲▼◀ and ▶buttons.
OSD	Select OSD to enter the menu. Control keys are Right, Left, UP, Down, Select, Far (REW KEY), and Near (FF KEY). Press the ESC button to return to the previous menu. Press the PTZ button to close the OSD menu.
AUTOSCAN	Press the right key(▶) to start auto scan. Press the left key (◀) to stop auto scan.
PRESET	Select PRESET, then press the left key(◀). A number input window will appear. Set the number (3digits) using the number key, then press the SEL to confirm the preset number for the current position. Press the right key (▶) and enter the number (3digits) to go to the preset position.
TOUR	Select TOLL and press the right (▶) key. A number

PTZ CH 11 INITIALIZE PAN/TILT ZOOM/FOCUS SEL ESC OSD AUTOSCAN PRESET TOUR 1 2 3 No : ... SET GO

5-2. Digital Zoom in Live and Playback Screen

RS series supports Digital Zoom feature during live and playback mode.

1. Double click the target channel.

CH 2 CH 5 CH 6

1. Click the left button of the mouse and drag to make rectangular shape.

Interior view of a modern exhibition hall showing a display case and a museum exhibit with an arrow pointing to it (no visible text or symbols)

5-3. SEARCH Screen

To enter the search screen menu, select SEARCH menu on the screen using the mouse or press SEARCH icon on live screen.

5-3-1. EZSearch

The EZSearch window is used to find stored video with ease using the thumbnail playback screen.

CH1 NO VIDEO CH2 NO VIDEO CH3 NO VIDEO CH4 Dec. 2011 Sun After Tune Memo Tray Fri Sat 4 2 5 4 6 8 7 8 9 10 12 13 14 15 16 17 18 19 20 21 22 23 24 20 21 22 23 24 CH13 NO VIDEO C:\WINDOWS\NOTES\CLOSED 12/28/2011 09:30:45 REC ALL OK

Figure 5.3.2. Calendar Screen

CH1 NO VIDEO CH5 NO VIDEO CH9 NO VIDEO CH13 NO VIDEO CH1 CH2 CH3 CH4 0 8 6 8 12 13 14 21 24 CH1 CH2 CH3 CH4 CH5 CH6 CH7 CH8 CH9 CH10 CH11 CH12 CH13 CH14 CH15 CH16 CH17 CH18 CH19 CH20 CH21 CH22 CH23 CH24 CH25 CH26 CH27 CH28 CH29 CH30 CH31 CH32 CH33 CH34 CH35 CH36 CH37 CH38 CH39 CH40 CH41 CH42 CH43 CH44 CH45 CH46 CH47 CH48 CH49 CH50 CH51 CH52 CH53 CH54 CH55 CH56 CH57 CH58 CH59 CH60 CH61 CH62 CH63 CH64 CH65 CH66 CH67 CH68 CH69 CH70 CH71 CH72 CH73 CH74 CH75 CH76 CH77 CH78 CH79 CH80 CH81 CH82 CH83 CH84 CH85 CH86 CH87 CH88 CH89 CH90 CH91 CH92 CH93 CH94 CH95 CH96 CH97 CH98 CH99 COM 2011.00:06:55 RC: ALL SIM

Figure 5.3.3. Channel Selection Screen

Grid of surveillance cameras with red annotation highlighting a specific camera's focus area

Figure 5.3.4. 24 Hourly Thumbnail Screen

Previous

Figure 5.3.5. Minute Thumbnail Screen

5-3-2. Time Line Search

The CALENDAR Search window is used to find the stored video by using the time line bar.

Nov. 2011 Sun Mon Tue Wed Thu Fri Sat 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 < PREV NEXT > CLOSE

Figure 5.3.7. Calendar Screen

11/02/2011 00:00:00 0 3 6 9 12 15 18 21 24 CH 1 CH 2 CH 3 CH 4 Channel ALL CH 1 CH 2 CH 3 CH 4 < PREV PLAY CLOSE

Figure 5.3.8. Time-Line Search Screen

When the Timeline menu is selected, the user can see a calendar, which displays recorded dates with highlights. Select a specific date and time. Click and drag the red time indicator bar to the desired hour. User can select a specific minutes using a button in the above red box. Press the PLAY button after selecting the specific time. Press the PREV to return to the SEARCH window.

5-3-3. Event Search

The Event Search window is used to find stored video.

CHANNEL FIRST|SECOND|THIRD|FOURTH EVENT MOTION|SENSOR|MANUAL|CONTINUOUS 1 / 2 Channel Log Date /

Channel ALL FIRST SECOND THIRD FOURTH Event ALL MOTION SENSOR MANUAL CONTINUOUS OK Cancel

Figure 5.3.10. Event Search Screen

5-3-4. Go To First Time

You can access from the oldest recorded data on the DVR hard drive by selecting GO TO FIRST TIME on the SEARCH window. Press the PREV to return to the SEARCH window.

5-3-5. Go To Last Time

You can access from the last minute recorded data on the DVR hard drive by selecting GO TO LAST TME on the SEARCH window. Press the PREV to return to the SEARCH window.

5-3-6. Go To Specific Time

User can search for video data from a specific instance by setting the date and time in the GO TO SPECIFIC TIME menu. Use the mouse or the control button on the remote control to change the date and time value and press the PLAY button after setting. If there is no video data in the set date and time, No Data Exist message displays.

5-3-7. Archive List

The ARCHIVE Search window is used to find previously stored video or images.

5-3-8. Log List

You can access the LOG list search screen by selecting LOG on the SEARCH window.

Log Date NTP : keeping (ntp time is earli-- 11/02/2011 03:00:39 Video Loss : SECOND 11/02/2011 08:18:43 Video Loss : FOURTH 11/02/2011 08:19:16 Video Loss : FIRST 11/02/2011 15:44:19 Video Loss : THIRD 11/02/2011 15:44:21 System Start 11/02/2011 15:49:15 Video Loss : FIRST 11/02/2011 15:49:15 Video Loss : SECOND 11/02/2011 15:49:15 Video Loss : THIRD 11/02/2011 15:49:15 Video Loss : FOURTH 11/02/2011 15:49:15 15 log(s) found. BACKUP < PREV NEXT CLOSE

Figure 5.3.12. Log List Screen

When the Log menu is selected, the user can see a calendar, which has a log data. Select a specific date and press NEXT button, and then the log data will be displayed. Press the SAVE button to save the data and then the data is saved as a text file format.

5-4. Play Mode

During playback of a recorded event, the mode changes from SEARCH to PLAY. While in PLAY mode, you may return to the SEARCH screen by pressing the X button on the status bar.

Interior view of a modern retail or exhibition space with ceiling lights and display cases (no visible text or signage)

	Press to play or pause recorded video.
	Jump/Step forward. Playback position moves 60 seconds forward.
	• 2x, 4x, 8x,16x, 32x speeds for D4RS/D4WRS• 2x, 4x, 8x,16x for D8RS/D8WRS• 2x, 4x, 8x for D16RS/D16WRSSingle Channel forward playback speed 1x, 2x, 4x, 8x, 16x, 32x, 64x
	Slow Mode play. Forward playback speed x1/4, x1/2
	Press to backup the video.
	EZCopy button.
	Return to the previous menu screen, search window, or exit from the Menu.

6. Back Up

6-1. Still Image Backup onto USB Flash Drive

Still images can be captured and archived onto a USB flash drive or an USB external hard drive in live mode or while playing back recorded video.

1. Select a specific channel, which wants to backup on live screen.
2. When you press SNAPSHOT button on Quick operation window, the media selection window screen will display

6-2. Video Backup onto USB Flash Drive during playback

Video can be captured and archived onto the USB flash drive or a hard drive while playing back the

recorded video. In playback mode, press the BACKUP button to launch the backup function.

1. When you press BACKUP button on the selected channel or all channels, the DVR will ask whether to archive a Still Image, a NSF or AVI and select the proper media type.

Please select archive media type • STILL IMAGE • NSF • AVI < PREY NEXT > CLOSE

Please select the media type USB STICK < PREV START CLOSE

1. Select USB STICK (Flash Drive) to back up less than an hour.

Select USB HDD (Large Backup) to back up from 1 hour to 24 hours.

Please select the media type • USB STICK • USB HDD (LARGE BACKUP) < PREV NEXT > CLOSE

1. Once you select the channel and duration, the system will start to archive the data to the USB drive.

Channel □ ALL □ CH 1 □ CH 2 □ CH 3 □ CH 4 □ CH 5 □ CH 6 □ CH 7 □ CH 8 □ CH 9 □ CH 10 □ CH 11 □ CH 12 □ CH 13 □ CH 14 □ CH 15 □ CH 16 Duration 1 MINUTES 07:12:2011 15:30:19 : 07:12:2011 15:40:19

6-3. EZCopy: Video Backup onto USB Flash Drive during playback

Using EZCopy feature, Video can be easily archived onto the USB flash drive or a hard drive.

In playback mode, press the COPY button to launch the backup function.

1. Press EZCOPY button on the selected channel or all channels.

User interface toolbar with playback controls and a cursor pointing to the EZ button

1. Then, EZCOPY START time will display.

2011/10/10 03:33:

1. Move time bar cursor to the time of end of backup and press EZCOPY button. Then, EZCOPY STOP time will display.

2011/10/10 04:44:

1. EZCOPY window will display. The DVR will ask whether to archive a Still Image, a NSF or AVI.

6-4. Transferring Still Images or Video from the ARCHIVE List

The stored data in the hard drive can be found in the ARCHIVE list in the SEARCH window.

User can back up still images or video into the storage device from the ARCHIVE list.

1. Select the date to begin searching and navigate through the days using the mouse or the control button or the remote control.
2. Once you have selected the date, press the NEXT button to open the list of stored data.
3. Use the mouse or the control button on the remote control to scroll through the archive list.
4. Select a list of stored events in the archive list.
5. Once the desired event has been selected, press the DISPLAY button to view the still image or the first frame of the selected video.
6. Press the BACKUP button to launch the archiving function in playback mode.
7. Press the CLOSE button to return to the SEARCH window.

Log Date / CH6 PLAY JPEG 07:13:2011 20:42:32 CH6 NFS(1 min) 07:13:2011 20:44:20 rfv AV(1 min) 07:13:2011 20:45:37 CH6 AV(1 min) 07:13:2011 20:48:48 rfv AV(1 min) 07:13:2011 20:55:52 CH6 AV(1 min) 07:13:2011 20:58:02 6 log(s) found. < PREV DISPLAY CLOSE

6-5. Playback of Backup Video

6-5-1. AVI Format

AVI format: AVI format video can be played back by Window Media Player™ or other media player that is compatible with AVI format video.

1. Please install the UMSDecoderFilter that the DVR copies "DvrPlayer" folder on USB flash drive with the video. UMSDecoderFilter is exported to the "/DvrPlayer" folder of the USB drive.

Computer + USB2005.0.1 > Default Organizers > Software > Auto > Monitor HomeGroup Computer USB2005.0.1 USB2005.0.1 USB2005.0.1 USB2005.0.1 USB2005.0.1 USB2005.0.1 USB2005.0.1 USB2005.0.1 USB2005.0.1 USB2005.0.1 USB2005.0.2 USB2005.0.2 USB2005.0.2 USB2005.0.2 USB2005.0.2 USB2005.0.2 USB2005.0.2 USB2005.0.2 USB2005.0.3 USB2005.0.3 USB2005.0.3 USB2005.0.3 USB2005.0.3 USB2005.0.3 USB2005.0.3 USB2005.0.3 USB2005.0.3 USB2005.0.3 USB2005.0.4 USB2005.0.4 USB2005.0.4 USB2005.0.4 USB2005.0.4 USB2005.0.4 USB2005.0.4 USB2005.0.4 USB2005.0.4 USB2005.0.4 USB2005.0.6 USB2005.0.6 USB2005.0.6 USB2005.0.6 USB2005.0.6 USB2005.0.6 USB2005.0.6 USB2005.1

1. Otherwise, the video and time stamp over video cannot be displayed properly in Windows Media Player™.

Interior view of a museum gallery with wooden flooring, display cases, and ceiling lighting (no visible text or signage)

Timestamp On AVI. The subtitle is embedded to the video clip file.

The subtitle is embedded to the AVI file. To display a subtitle, user must install a special filter "UMSDecoderFilter".

6-5-2. NSF Format

7. Network Access Using the Multi-Sites Network Viewer

7-1. Overview

The SpecoTech Multi Client is a multiple site monitoring client software with; video, audio, and alarm signals from the DVRs over networks. The SpecoTech Multi Client does not limit the number of DVR units to register.

The program displays up to 16 DVRs and supports dual monitors.

On the program, user may control PTZ cameras on the DVRs. By attaching a microphone and speaker system to devices on site, the user may make bi-directional audio communication over the network.

7-2. PC Requirements

Minimum PC Requirements

CPU	Intel Core i3
	1.8Ghz
Memory	2GB DDR2
VGA	512MB
Resoluon	1280x720
Disk Space	1GB
OS	Windows 2000, XP Professional, XP Home, Vista, 7 (NOTE: Not all versions of Vista and 7 are supported)
Network	10/100Base T
Others	Direct X 9.0c or Higher

Recommended PC Requirements

CPU	Intel Core i5

7-3. Installation of the Program

1. Insert the provided CD in the CD drive and double-click "SpecoTech Multi Client (XXXX).exe"

1. Select a destination folder and click "Next".

InstallShield Wizard Choose Destination Location Select folder where Setup will install files. Setup will install SpecoTech Multi Client in the following folder. To install to this folder, click Next. To install to a different folder, click Browse and select another folder. Destination Folder C:\...\Speco Technologies\SpecoTech Multi Client Browse... InstallShield < Back Next > Cancel

1. Select the program folder and click "Next".

InstallShield Wizard Select Program Folder Please select a program folder. Setup will add program icons to the Program Folder listed below. You may type a new folder name, or select one from the existing folders list. Click Next to continue. Program Folders:

7-4. Live Window

When installation is completed, double click the "SpecoTech Multi Client" icon on your desktop to start the program.

7-4-1. Main User Interface

speco Technologies SPECO Multi Client Ver 3.0.4.4

SITE MANAGEMENT		THUMBNAIL REFRESH: Click this icon to refresh and renew thumbnail image of the connected sites.SITE ADDITION: Click this icon to open 'Site Addition' window.SITE DELETE: Click this icon to delete site from the index window, after disconnect a site.NET FINDER: Select the site from the index window and click this icon to modify the information of specific site.
	CONNECT	Click this icon to connect the selected site/sites.
	DISCONNECT	Click this icon to disconnect the selected site/sites.
	SETUP	Click this icon to setup configuration of UMS MULTI CLIENT.
	CAPTURE	Click this icon to capture a still image.
	EVENT LIST	Opens list of events logged by the UMS Multi Client.
	PAUSE	Click this icon to play/pause live video.
	ALARM ON	Click this icon to turn on/off alarm outputs.
	RECORD ON	Enable or disable recording of live video to local disk, which has set in setup menu.
		Use the volume control bar to set the audio level.

7-5. Search and Playback Window

7-5-1. Main User Interface

You can access to search window by clicking the search icon (Local Playback / Remote Playback) on the upper right of the Live Window.

SPECO Multi Client Ver 3.0.4.4 2011-01-19:00:00:00 M T W T F S 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 25 26 27 28 29 30 +0.04 10 14 18 22 24 25 26 27 28 29 30 31 32 33 34 DARS P: 25.15E 1.15T 2011 Jul

7-5-2. Main Control Panel

Button	Description
	Click this icon to run a playback window to search and play videos that
CONNECT	Click this icon to connect the selected site/sites.
DISCONNECT	Click this icon to disconnect the selected site/sites.
ETUP	Click this icon to setup configuration of SpecoTech Multi Client.
CAPTURE	Click this icon to capture a still image.
/ENT LIST	Opens list of events logged by the UMS Multi Client.
Copy Start	Click this icon to set the beginning time for backup of the recorded video in AVI format.
Copy End	Click this icon to set the ending time for backup of the recorded video in AVI format.
ACKUP	Click this icon to backup the recorded video in AVI format.
	Use the volume control bar to set the audio level.
	To select the numbers of DVR/DVRs (1 DVR, 4 DVRs, 9 DVRs, 16 DVRs) on main display screen.
	To select the numbers of display channel/channels (Single, quad, channels, and 16 channels) of highlighted site.
	To select the channel to playback.

7-6. Setup of SpecoTech Multi Client

Click the setup icon

to setup the configuration of UMS Multi Client software. The SETUP

window is displayed as below.

7-6-1. General

Security Option: Set a password for security options. Select security options and set a password.

Then when you access any of selected functions, you need to enter the password.

You can also set the save path for capturing and backup.

Save Path: Specify the location to save captured still image for Capture and Backup data.

Miscellaneous

Automatic Reconnection: If enabled, the software will automatically try to reconnect to the last successful IP address. But, when CLIENT ACCESS is OFF on the DVR, the software will not try to reconnect even if it is enabled.

Always On Top: If enabled, the software display will be continuously on the top of other windows.

Time Format: Change the way the Client software displays the time.

Setup General Event Event search Record Disk Display Language About Security Option Startup Shutdown Setup Local Playback Remote Playback Password... Save Path Capture : C:\Storage\Capture\ Backup : C:\Storage\Backup\

7-6-2. Event

Event log can be archived and searched.

Event Log: Specify the location to save event logs and select event to archive.

Setup General Event Event search Record Disk Display Language About Log Path : C:\Storage\Log\ Size : 10 (MAX : 100MB) Event Log Event list Startup ✓ ✓ Shutdown ✓ ✓ Setup Change ✓ ✓ Sensor in ✓ ✓ Alarm out ✓ ✓ Motion ✓ ✓ Camera loss ✓ ✓ Network loss ✓ ✓ Record ✓ ✓ OK Cancel

Event Search: Event log can be searched from the selected time.

Setup General Event From: First 2011-04-26 12:00:00 AM To: Last 2011-04-26 7:48:54 PM Find

7-6-3. Record

Record Setup: You can set the recording conditions as the following; Always, Event, or Auto record. And you can also select target DVR/DVRs and channel/channels. When you set the recording condition to event, you can set event for motion or alarm with duration.

Setup General Event Event search Record Disk Display Language About Record Condition Always Event Auto record Event Motion Alarm Duration: 5 Sec Channel Site : Site 1 All site All NO. CH 1 Channel 1 2 Channel 2 3 Channel 3 4 Channel 4 5 Channel 5 6 Channel 6 OK Cancel

Record Local Storage Setup: You can select the local disk to record and the amount of disk space you want to allow the program to use for recording. You can also select the option to overwrite data or stop recording when the maximum amount of disk space is full.

Setup

7-6-4. Display

You can select the OSD (On Screen Display) to be displayed.

Setup General Event Event search Record Disk Display Language About OSD Site : Site 1 All site Info Display network statistics Date/Time Event ✓ Alarm ✓ Motion ✓ Sensor ✓ Record ✓ Video Loss Display Secondary monitor image correction Please use this option only on the PC when having a shattered image on the secondary monitor during use of multi monitor. If option is enabled, the performance of the program may drop. OK Cancel

7-6-5. Language

English, French and Spanish is selectable.

Setup General

7-6-6. About

"About" provides network client version information.

Setup General Event Event search Record Disk Display About SPECO Multi Client Version 3.0.4.4 (Build 110524) Copyright (C) 2011 This product licensed to : Warning: this computer program is protected by copyright law and international treaties. Unauthorized reproduction or distribution of this program, or any portion of it, may result in severe civil and criminal penalties, and will be prosecuted to the maximum extent possible under the law. OK Cancel

7-7. Remote Setup

The menu settings for the DVR unit can be set over network.

Put the cursor of the mouse on the channel, which is connected to the site and right click on the mouse to open the submenu. Then the following window is displayed as below. Select the REMOTE SETUP.

SPACE VOUTRUNNING CH-2 NO VIDEO Decisions Full Screen Setup Rename Setup This currently Lock Use Information Last

Then the setup window is displayed. The specified menu screen is displayed on the upper left of the screen.

Enter the password of the DVR when prompted. (NOTE: The default password is 1111)

Setting is the same as with the DVR menu setting. Refer to the corresponding pages for details on the

setting items.

7-7-1. System

Select System to set system and time settings.

SYSTEM RECORD DEVICE DISPLAY NETWORK USER MANAGEMENT STORAGE UPGRADE DATE DISPLAY FORMAT MMDDYYYY CLIENT ACCESS ON OFF NTP SETUP OFF PRIMARY SMTP SERVER Post.nfp.org SECONDARY SMTP SERVER Time hit gov TIME ZONE GMT +0:00 (Labon/London/Moresea) CONNECTION MODE TIME CONNECTION PERIOD 05:00 AM SEND EMAIL SETUP ON TRANSMISSION MODE VIDEO IP NOTIFICATION OFF MAIL BY SENSOR OFF MAIL BY MOTION OFF MAIL BY VIDEO LOSS ON MAIL BY S.M.A.R.T. OFF MAIL BY STATUS ON PERIOD DAILY FIRST SUN 10 H MAIL PORT 25 SECURE OPTION NONE MAIL TO MAIL SERVER: ID PASSWORD MAIL FROM UNIT NAME

• DATE DISPLAY FORMAT: Select the date display format.
- CLIENT ACCESS: Enable/Disable remote access through network client software.
- NTP SETUP: Sets whether to synchronize the time using NTP server or not.
o Primary SNTP Server: Input the NTP primary server address.
Secondary SNTP Server: Input the NTP secondary server address.
- Time Zone: Select the time zone.
o Connection Mode: Select the connection mode to NTP time server.

7-7-2. Record

Select RECORD tab to set the recording conditions.

SYSTEM RECORD DEVICE DISPLAY NETWORK USER MANAGEMENT STORAGE UPGRADE SITE CH1 RESOLUTION D1 FRAME RATE 5 FPS QUALITY LEVEL 5(H) RECORDING MODE MOTION SENSOR RECORDING - - - PRE RECORD 1 MINUTE(S) POST EVENT RECORD 10 SECOND(S) AUDIO ● ON ● OFF EZRecord APPLY EZRecord RESOLUTION D1 FRAME RATE 6 FPS QUALITY LEVEL 5(H) RECORDING MOTION DAYS TO RECORD 1 DAY(S) 1 HOUR(S)

These settings apply to the specified channel only.

- Recording Setup

o RESOLUTION: Sets the resolution for the recordings. The set value applies to an individual channel.
o FRAME RATE: Sets the recording rate.
o QUALITY: Sets the image quality in 5 levels.
o RECORDING: Sets the recording mode.
o RECORDING MODE: CONTINUOS, SCHEDULE, MOTION
o PRE RECORD: Sets whether to perform or not pre recording.
o POSE EVENT RECORD: Sets the duration of the event recording.
o AUDIO: Sets whether to perform or not audio recording.

These settings apply to all channels.

7-7-3. Device

Select Device to set Spot Out, Enable/Disable CVBS Out, motion zone.

SYSTEM RECORD DEVICE DISPLAY NETWORK USER MANAGEMENT STORAGE UPGRADE ALARM OUT SENSOR IN MOTION ON VIDEO LOSS ON ALARM DURATION ERROR ALARM CONTROLLER SPEED ID PTZ CHANNEL CAMERA SPEED ID MOTION SITE MOTION ZONE MOTION SENSITIVITY CH1 FULL ZONE 5 KEY TONE ● ON ● OFF REMOTE CONTROLLER ID 0 SENSOR 1 TYPE OFF

• ALARM OUT: Set the sensor, motion, and video loss for triggering alarm relay HDD Error and Video Loss can trigger beeping.
  • CONTROLLER: Set the controller baud rate and ID.
  • PTZ: Set the PTZ baud rate, protocol, and ID.

• MOTION: Setup the motion detection area and the sensitivity.
  o SITE: Select the channel
  o MOTION ZONE: FULL Zone or PARTIAL Zone
  o MOTION SENSITIVITY: 1\~9 (High sensitivity level)
  • KEYTONE: Sets On or Off of Key Tone.
  • REMOTE CONTROLLER ID: Sets an ID number on the supplied remote control for its identification.

• MAIN MONITOR SEQUENCE: Setting for automatically switching the displayed video.
  • SEQUENCE DWELL TIME: Sets the interval for automatically switching the screens.
  • SITE: Name, Covert, Brightness, Contrast, Hue, Saturation

These settings apply to the specified channel only.

7-7-5. Network

SYSTEM RECORD DEVICE DISPLAY NETWORK USER MANAGEMENT STORAGE UPGRADE NETWORK TYPE IP SUBNET MASK GATEWAY DNS (PRIMARY) DNS (SECONDARY) DDNS HOST NAME SUBMITAUPDATE eADDINS NETWORK PORT NETWORK AUDIO PORT WEB PORT NETWORK STREAM RESOLUTION FRAME RATE QUALITY DHCP 192.158.1.22 255.255.255.8 192.158.1.1 192.158.1.1 ON hostname ON ON 5445 5446 80 CH1 CIF 10 FPS LEVEL 5(H)

• NETWORK TYPE

o STATIC: The address setting mode is manual. Input IP, Gateway, Subnet Mask, and DNS IP.
o DHCP: The address setting mode is automatic.

- DDNS: Set whether to use DDNS service or not.

• HOST NAME: Allows the user to setup a domain name manually
  SUMBIT/UPDATE: Select ON to submit the settings
• ezDDNS: Enable/disable ezDDNS to register the host name automatically

• NETWORK PORT: When connecting multiple DVRs to the network. set a unique port number.

7-7-7. Storage

Select Storage to configure continued recording settings by overwriting the hard disk and the storage period for the recording data.

SYSTEM RECORD DEVICE DISPLAY NETWORK USER MANAGEMENT STORAGE UPGRADE OVERWRITE ON OFF RECORDING LIMIT OFF RECORDING LIMIT DAYS 30 DAYS(5) S.M.A.R.T. TEMPERATURE LIMIT 80°C 140°F ALARM ON OFF BUZZER ON OFF

• OVERWRITE: To continue recording by overwriting when the hard disk becomes full, check the checkbox.
- RECORD LIMIT: Sets whether to limit or not the recording data storage period.
- S.M.A.R.T.: Sets the TEMPERATURE LIMIT of the Hard Disk to trigger the ALARM and the BUZZER.

7-7-8. Remote Upgrade

SYSTEM RECORD DEVICE DISPLAY NETWORK USER MANAGEMENT STORAGE UPGRADE Current Software: Ver 3.1.18, 07:15:2011 Browse UPGRADE

Shows the current Firmware version installed on DVR.

• Browse: Select BROWSE to locate the firmware file.
• Upgrade: Select UPGRADE to upgrade the firmware of the DVR.

7-8. Operation

7-8-1. Addition, Delete, and Modify of DVR Sites

7-8-1-1. Addition of Sites

1. Click SITE ADDITION button. And then the following window will be displayed as below.

Site Addition Site Info Site Name: D4RS Site Address: 192.168.1.111 Port Number: 5445 ID: admin Password: ***** OK Cancel

• Site Name: Input a name that properly describes a site.
• IP Address: Input IP address (Public IP address of a router that DVR is connected.) or Domain name
• Port Number: Default Port Number is "5445".
  ID: Input ID of DVR. Default ID is "admin".

• Password: Input network password of DVR. Default Password is "1111".

• Click OK button. And then the registered site is added on the directory window.

7-8-1-3. Modify of Sites

1. Select the site/sites to modify from the directory window.

D4RS IP : 192.168.1.151

1. Click NET FINDER button. And then the following window will be displayed as below.

Net Finder Name Address D4R5 192.168.1.151 Address Port No. Mac Model Add Modify Delete Find JP Change Close

7-8-2. Connect and Disconnect

7-8-2-1. Connect

1. Select site/sites to connect from the directory window.

1. Click CONNECT button, and then site/sites displays/display as connected.

01.2 01.3 01.4 01.5

7-8-2-2. Disconnect

1. Select site/sites to disconnect from the directory window.

7-8-3. Still-image Capture During Live

1. Double-click a channel to capture from the display screen. (Otherwise all channels will be captured).

Side-by-side comparison of a road scene before and after transformation, showing original and rotated views with no visible text or symbols.

1. Click CAPTURE button. And then a Capture window will be displayed as below.

Capture Save Path: C:\Storage\Capture\D4RS File name: 2011-07-19-112621 File Format: BITMAP(*.BMP) Browse OK Cancel

1. Set Save Path, File Name, and File Format. And then click OK button.
2. Still image is saved as set in Capture window.

Storage > Capture > D4RS Organize Include in library Share with Slide show Burn New folder Documents Music Pictures

7-8-4. Recording Video on Local PC During Live

1. Click SETUP button. And then a setup window will be displayed as below.
2. Select Record and set the values.

Setup General Event Event search Record Disk Display About Record Condition Always Event Auto record Event Motion Alarm Duration: 5 Sec Channel Site : Site 1 All site All NO. CH 1 Channel 1 2 Channel 2 3 Channel 3 4 Channel 4 5 Channel 5 6 Channel 6 OK Cancel

1. Select Disk and set the values.

Setup General Event Event search Record Case Display About Disk Space: C:\ 4 SD Disk Info Total space: 465 GB Free space: 308 GB Disk full Replace oldest files Stop recording

7-8-5. Local Playback and Remote Playback

7-8-5-1. Playback of Recorded Video on a Local PC

1. Click LOCAL PLAYBACK. And then Playback Window will be displayed over the Live

Window.

SPECO Multi Client View 3.0.4.4

1. Select site/sites to connect from the directory window.

2. Click CONNECT button. And then Green bar displays on Search calendar and timeline scale window.

2011 April M T W T E S 3 4 5 6 7 8 9 10 11 12 13 14 15 16 37 38 39 40 41 42 43 44 45 46 24 25 26 27 28 29 30 0 2 4 6 8 10 12 14 16 18 20 22 24

1. Move the marker on the timeline scale to where there is video data and press the PLAY button.

7-8-5-2. Playback of Recorded Video on Remote DVR

1. Click REMOTE PLAYBACK. And then Playback Window will be displayed over the Live

Window.

SPECO Hulo Client Vol 1.0.5.6

1. Select the site to connect from the directory window.

2. Click CONNECT. And then Green bar displays on Search calendar and timeline scale window.

S M T W T F S 1.2 3.4 5 6 7 8 9 15 11 12 13 14 15 16 17.18 19 20 21 22 23 24 25 26 27 28 29 30 0 2 4 6 8 10 12 14 16 18 20 22 24 0-50 1 2011 Apr

1. Move the marker on the timeline scale to where there is video data and press the PLAY button.

7-8-6. AVI Backup during Playback

You can back up the recorded videos in AVI format during playback.

1. Double-click the target channel to backup.
2. Select the beginning time by using the search calendar and timeline scale bar.

2011 Apr S M T W T F S 1 2 3 4 5 6 7 8 9 5 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 0 2 4 6 8 10 12 14 16 18 20 22 24

1. Click EZCOPY START button on the timeline scale to select the beginning point of the backup.

0 10 20 30 40 50 60

1. Click EZCOPY END button on the timeline scale to select the ending point of the backup. Then, the selected starting point and the ending point on the timeline scale bar will be marked in green.

0 10 20 30 40 50 60

1. Click BACKUP. And then the BACKUP window will be displayed as below.

Backup Select Channels

1. You can also set the beginning time and ending time on this window. After selecting a channel for backup, click the OK button. The backup will begin.

Backup Select Channels CH-1 CH-2 CH-3 CH-4 All Setting Start Time: 01:17:18 End Time: 01:19:43 File Path: C:\Storage\Backup\ File format: AVI 7.6% OK Cancel

1. AVI video data is recorded as set in AVI Backup window. AVI format video can be played back by using Window Media Player™ or other media player that is compatible with AVI format video.

Exterior view of a rural landscape with trees, buildings, and utility poles under a clear sky (no signage or text visible)

8. Network Access Using the Web-Browser Viewer

The DVR provides a live remote monitoring feature by web-browser viewer. (NOTE: Web-Browser is only available for Internet Explorer)

1. Check the IP address of the DVR from SETUP>SYSTEM>DESCRIPTION>IP ADDRESS or
2. Input the IP address or Domain name address that you pre-registered.

Address http://172.16.1.52 Go

1. Click this bar. Then the dialog box is displayed.

1. Click "Install" to download and install the ActiveX control.

User Account Control Do you want to allow the following program to make changes to this computer? Program name: SpecoTech-WebViewer(ver1.4.8.7) Verified publisher: Speco Technologies File origin: Downloaded from the Internet Show details Yes No Change when these notifications appear

1. The Web Browser Viewer will be displayed as below after the ActiveX installation

2011-04-26 2:12:27 Space to Studio Player

Connect -- Webpage Dialog http://192.168.1.12/login.html Connect to remote system Address 192.168.1.12 Port 5445 ID admin Password •••••| Connect Cancel

• Site Name: Input a name that properly describes a site.
• IP Address: Input IP address (Public IP address of a router that DVR is connected.) or Domain name
  • Port Number: Default Port Number is "5445".
  • ID: Input ID of DVR. Default ID is "admin".

• Password: Input network password of DVR. Default Password is "1111".

• Then the cameras connected to the DVR are displayed on the screen.

• Use mouse scroll to digitally zoom in and out from a single channel display.

Timeline Technologies G1.1 G1.2 Time 0:00:27 19:52:43 Time 1:06:1:12

9. Network Access Using the Smart Phone Viewer

Notice

Data Usage will be applied if there is no Wi-Fi connection. Please check with your Phone Carrier.

9-1. App Viewer for iPhone

1. Enter the Apple App Store.

1. Search "Speco Player" in the App Store.

Notice

SPECO Player is for the RS, WRS and HD series DVRs. SPECO VIEWER is not compatible with the T Series DVR's (TH, TN or TL) or the PC Series DVR's.

9-1-1. Live

1. Open the installed "Speco Player" App and select the Live Preview. Then click the menu buon of the phone to add a remote device.
2. Select the registered device and select the channels to monitor up to 4 channels. Select Mode as 'Live' and click 'Connect'

LIVE 11:59 AM 80% 2011-11-16 11:59:55 362 x 140

10-3-2.PTZ Control

To control the PTZ funcons of the camera, tap the menu buon. Then PTZ menu icons will display. Using the PTZ icon on the screen, control PTZF control.

Dennis LIVE CH1) 2011-11-16 11:56:53 Dennis LIVE CH1) 2011-11-16 11:57:02 PFE DOOM PHOSER PFE DOOM PHOSER

10-3-3. Playback

1. Select the registered device and select the channels up to 4 channels to search and playback. Select Mode as 'Playback' and click 'Connect'. Then the search window will display.

Demo Select Date & Time Mon Nov 14 1 44 Tue Nov 15 2 45 AM Today 3 46 PM Thu Nov 17 4 47 Fri Nov 18 5 48

DATE Hour Min.

1. The app will display the selected channel(s). Double tap the channel screen to switch 1 channel display to 4 channels split display or vice versa.

PLAYBACK 30+180 30+140 2011-11-15 17:35 SAT 12:09 PM Select Data & Time PLAYBACK 2011-11-15 17:35 3G x 2011

1. Tap the menu buon. Then Playback menu icons will display.

9-2. Ann Viewer for Android Phone

Devices Add or remove devices D4RS

Channel Select Select a monitoring device Device Q485 IP/DNS 192.168.1.12 Port 5445 ID admin Password **** Select to Channel 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 Select

1. The app will display the selected channel(s). Double tap the channel screen to switch 1 channel display to 4 channels split display or vice versa.

Live Preview PTZ FOCUS ZOOM

Live Preview PTZ FOCUS ZOOM

APPENDIX: Network Connection - LAN

IP Router or HUB

1. Install the network client software from the supplied CD.
2. Check the IP address from SETUP > SYSTEM > DESCRIPTION or SETUP > NETWORK of DVR.

SOFTWARE VERSION Ver 3.2.1 (07/11/2011) STORAGE SIZE 217 GB IP ADDRESS 192.168.1.111 MAC ADDRESS 00:02:69:00:00:01 DDNS STATUS DDNS OFF OK

1. Run the network client software.

special technology 文件(F) 123 01.1.12

Site Addition Site Info Site Name : D4RS Site Address : 192.168.1.111 Port Number : 5445 ID : admin Password : ****. OK Cancel

1. Input Site Name, Site Address (IP address), Port Number, and Password on the connect window.

2. Site Name: Input a name that properly describes a site.
   • IP Address: Input IP address

3. Port Number: Default Port Number is "5445".
   • ID: Input ID of DVR. Default ID is "admin".

4. Password: Input network password of DVR. Default Password is "1111".

5. Select a site by checking the box, and Press button to connect to the site.

space technologies CH-2 NO VIDEO

APPENDIX: Network Connection – Internet and DDNS

Dynamic Domain Name System (DDNS) allows a domain name to be constantly synchronized with a dynamic IP address. A current dynamic IP address is being associated with a static domain name.

graph TD
    A["PC"] -->|USB| B["Internet"]
    B --> C["Laptop"]
    D["ADSL"] --> E["IP Router or HUB"]
    E -->|USB| D
    style A fill:#f9f,stroke:#333
    style B fill:#ccf,stroke:#333
    style C fill:#cfc,stroke:#333
    style D fill:#fcc,stroke:#333
    style E fill:#cff,stroke:#333

1. Go to SETUP>NETWORK>DDNS and set the DDNS SERVER to ON.

ENABLE DDNS HOST NAME SUBMIT/UPDATE ezDDNS ON hostname ON ON APPLY CLOSE

If you set ezDDNS to ON, the host name is automatically generated and registered.

1. When a manual host name is completed, Go to SETUP>NETWORK>DDNS>SUBMIT/UPDATE and select ON to submit the settings on the SPECO DDNS.

Once the setting is completed, the DDNS address will be: http://hostname.ddns.specoddns.net For example, if you enter the host name as "D4RS", then the address will be: http://d4rs.ddns.specoddns.net

1. When DDNS setting is done, click the APPLY button. Otherwise DDNS setting will not be applied.
2. When you exit SETUP menu, DDNS NOTIFY window will pop up.

1. DDNS registration status can be checked from SYSTEM INFORMATION or SETUP>SYSTEM>DESCRIPTION>DDNS STATUS

SOFTWARE VERSION Ver 3.2.1 (07/11/2011) STORAGE SIZE 217 GB IP ADDRESS 192.168.1.111 MAC ADDRESS 00.02.69:00:00:01 DDNS STATUS READY(44m) OK

1. Check the NETWORK PORT (Default: 5445), WEB PORT (Default: 80), and the IP Address of the DVR from SETUP>NETWORK.

2. Port forward the NETWORK PORT (Default: 5445) and WEB PORT (Default: 80) of the private IP Address of the DVR on the network router.

Please refer to the user manual and guide for the detailed steps for port forwarding for specific router model.

1. Run the network client software.

SPECD Multi Client Version 2014.4.6

Site Addition Site Info: Site Name: DIRS Site Address: 0416-0092.054000003.net Port Number: 5485 ID: admin Password: ****. OK Cancel

1. Input Site Name, Site Address (IP address), Port No., and Password on the connect window.

2. Site Name: Input a name that properly describes a site.
   • IP Address: Domain name or Public IP address of a router that DVR is connected.
   • Port Number: Default Port Number is "5445".
   • ID: Input ID of DVR. Default ID is "admin".

3. Password: Input network password of DVR. Default Password is "1111".

8 And select the OK button. Then press button after checking the left check box

APPENDIX: E-SATA CONNECTION

Please read the following instructions before using the E-SATA port. Failure to do so may cause serious damage to the recorded video. SPECO is not responsible for data loss caused by improper usage.

• Use ONLY a new HDD or a HDD that is pre-formatted on a PC.
• Turn off the DVR before plugging the E-SATA HDD.
• DO NOT disconnect the E-SATA port while the DVR power is on.
• The purpose of the E-SATA port is to extend recording capacity.
• Once connected, DO NOT remove or disconnect the E-SATA port from the DVR.
• The E-SATA port is does not support the hot swappable function.