HTD8FFI - Security Camera Speco Technologies - Free user manual and instructions

USER MANUAL HTD8FFI Speco Technologies

580 Line Color Dome Camera

Intensifier 2 Series, Focus Free

Wall & Ceiling Mountable

WARNING & CAUTION

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION

TO REDUC E THE RISK OF ELECTRIC SHOCK

DO NOT REMOVE COVER (OR BACK).

NO USER SERVICEABLE PARTS INSIDE

REFER SERVICING TO QUALIFIED

SERVICE PERSONNEL.

The lighting flash with an arrowhead symbol, within an equilateral triangle is intended to alert the user to the presence of un-insulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons

The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (serving) instructions in the lit e r a ture ac c om panying th e applian ce

INFORMATION -This equipment has been tested and found to company with limitsforaclassadigitaldevicePursuanttopart15oftheFCCrules.

These limits are designed to provide reasonable protection against harmful

CONTENTS

Package Contents 4

Precautions 5

Camera Installation 6-10

Features 11-12

OSD Menu Tree 13

OSD Menu Details 14-17

PACKAGE CONTENTS

Please make sure that the following items are included in the package:

1 HTD8FFi Series Camera
4 Mounting Screws
1 Video test Connector
1 Rubber Cap
1 Wrench

PRECAUTIONS

• THIS CAMERA SHOULD BE ONLY INSTALLED BY QUALIFIED PERSONNEL
  • TO PREVENT A FIRE OR ELECTRICAL HAZARD PLEASE USE PROPER POWER CABLE
• DO NOT CLEAN THE DOME COVER WITH AN ABRAISIVE CLEANING MATERIAL - PLEASE USE A SOFT CLOTH OR TISSUE TO CLEAN THE DOME COVER
• THERE ARE NO USER-SERVICEABLE PARTS INSIDE. PLEASE DO NOT DISASSEMBLE THIS CAMERA OTHER THAN TO MAKE INITIAL ADJUSTMENTS
• PLEASE USE A UL APPROVED REGULATED 24 VOLT AC OR 12 VOLT DC POWER SUPPLY
• PLEASE USE APPROPRIATE LOW VOLTAGE POWER CABLE TO PREVENT FIRE OR ELECTRICAL SHOCK

CONNECT POWER CABLE

1. WHEN USING 12 VOLTS DC (constant voltage 500 mA)

Power Input :RED Center : (+) DC 12V Power Supply

1. WHEN USING 24 VOLTS AC (40 Volt Amps)

RED(+) BLACK:(-) AC 24V Power Supply

1. CONNECT VIDEO CABLE

-CONNECT BNC CABLE TO THE BNC JACK.

4 CONNECT Alarm output (Delay output)

CAMERA INSTALLATION

ASSEMBLY

Easy Mount Plate

Rubber Cap used when cables go through the mount

Technical line drawing of a mechanical component with multiple cylindrical pins and mounting holes (no text or symbols)

SET Screws (2ea)

Camera Base

Mounting Screws (4ea)

Camera Body

CAMERA INSTALLATION

COMPATIBILITY

7246WMT CVCTPEXT "A" type Box "B" type Box

Technical line drawing of a mechanical component assembly (no text or symbols)

Technical line drawing of a mechanical component with cross-sectional views (no text or symbols)

MULE PH

Technical diagram of a mechanical component with labeled parts and assembly lines

CAMERA INSTALLATION

CONTROL BOARD DETAILS

[Front Board] [Rear Board]

Heater

Zoom (In & Out) Joystick

CAMERA INSTALLATION

DIP Switch Setting for RS-485 (Pelco-D)

Address Baud Rate 1 2 3 4 5 6 7

1) Address Setting

to set Camera Address, place switches based on below chart.

Horizontal resolution of 580 TV lines is achieved by using a SONY Double Speed CCD with 410,000 pixels, yielding pictures with a high S/N ratio..

INTENSIFIER

1/3 inch density CCD and digital processor permit high quality Pictures to be captured in very low light condition.

SPECO DNR

The Intensifier camera has a DSP chip that can remove image noise efficiently showing clean images in low light conditions.

FEATURES

OSD

All camera functions are menu driven for easy use.

SLC

When the image is in front of strong background lighting, your camera allows you to get the clear image.

HLC (High Light Compensation)

This function reverses bright spots in the picture (such as headlights). This enables the entire system to do a better job of resolving and displaying grayscale information such as a license plate.

OSD MENU TREE

OSD MENU DETAILS

1. INTENSIFIER

[OPTION : E SHUTTER / AUTO GAIN / INTENSIFY / RETURN]

- E SHUTTER

* FLK - Flicker-less mode (FLK) reduces on-screen flickering.
* ESC - Electronic Shutter Control (AUTO) adjusts brightness level on screen.

- AUTO GAIN

Adjusts value of AGC gain and increases the GAIN level to brighten the picture. (noise / distortion may develop)

- INTENSIFY : Automatically provides a clear image under low-light conditions. You can control the maximum low-light magnification from 2x to 256x (increasing magnification may cause noise/distortion). This function is deactivated when SHUTTER is set to FLK mode.

2. COLOR TEMP

[OPTION : ATW / INDOOR / OUTDOOR / AWC SET / MANUAL]

OSD MENU DETAILS

3. WDR SET

[OPTION : SLC / HLC / OFF]

• SLC (Speco Light Compensation)
  Provides light level control to overcome severe back light condition.

- HLC (High Light Compensation)

High Light Compensation removes the high light and makes possible to view the image clearly.

4. SPECO DNR

[OPTION : ON / OFF]

- Reduces noise/distortion on the screen. Increasing the DNR level reduces noise but may introduce video artifacts. DNR is deactivated if AGC is turned off.

5. DAY / NIGHT

[OPTION : COLOR / BW / AUTO]

OSD MENU DETAILS

1. CAM TITLE

[OPTION : ON / OFF]

- Display a name and/or number on the monitor you prefer.

1. SYNC TYPE

[OPTION : INT / LL]

- INTERNAL : When line lock is not required.

- LINELOCK : Adjust the vertical phase (VPH) from 000\~359 (factory default is 0). This function is only available with 24VAC power.

1. V MOTION

[OPTION : ON / OFF]

- When movement is detected, camera sends a signal to an external alarm device.

OSD MENU DETAILS

10. PRIVACY

[OPTION : ON / OFF]

- Mask up to 8 areas of the screen from video monitoring.

PRIVACY 1. AREA SEL AREA1 2. AREA MODE ON 3. MASK COLOR GRAY 4. TRANSP 0 5. RETURN

• AREA SEL : Select up to 8 motion detection area.
• AREA mode : Activate or deactivate the selected area.
• MASK COLOR : Select area color.
• TRANSP : Adjust the transparency of selected area.
• RETURN : Save the settings and return to the SPECIAL menu.

TROUBLESHOOTING

If you have trouble operating your camera, refer to the following

Problem Solution
Nothing appears on the screen.	● Check that the power cord and line connection between the camera and monitor are proper● Check that you have properly connected VIDEO cable the camera VIDEO output jack.
The image on the screen is dim.	● Is lens stained with dirt? Clean your lens with soft, clean cloth.● Set the monitor to proper condition.● If the camera is exposed to too strong light change the camera position.● Adjust the lens' focus properly.
The image on the screen is dark.	● Adjust the contrast feature of the monitor.● If you have an intermediate device, set the 75Ω/Hi-z properly.

TROUBLESHOOTING

Problem Solution
The color of the picture is not matched.	● Check that you have properly set the ‘WHITE BALANCE’ menu
The image on the screen flickers.	● Is the camera facing to direct sunlight or fluorescent lighting? Change the camera position.
L/L mode isn’t able to be selected.	● Have you connected your camera to DC power source? Connect it to AC power source.

SPECIFICATIONS

ITEM HTD8FFi
Power Source 12VDC & 24VAC ( Dual Voltage )
Power Consumption 500mA (DC) / 6.6W (AC)
Image Sensor 1/3", SONY SUPER HAD CCD, 410,000 pixels
Total Pixels 811(H) x 508(V), 1/3" CCD
Effective Pixels 768(H) x 494(V), 1/3" CCD
LENS TYPE	Focus Free Lens 2.8~10mm
Maximum Aperture Ratio 1 : 1.3 ~2.0
Scanning System 2 : 1 Interlaced 525 Lines / 60 Fields / 30 Frames
Synchronization Internal / Line Lock selectable
Video Output 1.0V [p-p] Composite, 75Ω
Resolution 580 TV Line
Gain Control AGC-L, AGC-H, OFF selectable
Electric Shutter Speed	1/60 ~ 1/200,000 sec
INTENSIFIER 2	Built-in ( selectable limit ~ X256)

DIMENSIONS

* FRONT VIEW

Ø66 153.1 92 Ø129.8

* SIDE VIEW

WARRANTY

speco technologies

LIMITED WARRANTY

THIS WARRANTY IS VALID ONLY ON PRODUCTS PURCHASED AND USED IN THE UNITED STATES OF AMERICA THIS WARRANTY APPLIES ONLY TO THE ORIGINAL USER.

SUBJECT TO CONDITIONS AND EXCLUSIONS FOUND BELOW. THIS PRODUCT IS WARRANTED AGAINST MANUFACTURING DEFECTS IN MATERIAL AND WORKMANSHIP FOR THE FOLLOWING PERIOD FOR PARTS AND LABOR:

SPECO TECHNOLOGIES CAMERAS: 5 YEARS

SPECO TECHNOLOGIES MONITORS: 1 YEAR

BALANCE OF SPECO TECHNOLOGIES LINE: 1 YEAR*

* IR LEDs, Time lapse VCR Drum Assemblies & Heads: 90-DAYS

SPECO TECHNOLOGIES WILL REPAIR OR REPLACE (AT OUR DISCRETION) ANY PARTS FOUND TO BE DEFECTIVE FOR THE WARRANTY PERIOD SPECIFIED. WE WILL PROVIDE A REPLACEMENT FOR ANY DEFECTIVE PART.

CONDITIONS

1. YOU MUST OBTAIN A RETURN AUTHORIZATION NUMBER FOR ANY MERCHANDISE BEING RETURNED TO SPECO TECHNOLOGIES, WHETHER FOR RETURN/EXCHANGE OR REPAIR, WHETHER IN OR OUT OF WARRANTY.

2. THIS WARRANTY WILL BE HONORED ONLY UPON PRESENTATION OF THE ORIGINAL DATED BILL OF SALE OR SALES SLIP.

3. TRANSPORTATION OF THE PRODUCT TO OUR SERVICE DEPARTMENT IS THE RESPONSIBILITY OF THE USER, REPAIRED OR REPLACED PRODUCT WILL BE RETURNED PREPAID DURING THE WARRANTY PERIOD.

EXCLUSIONS

1. THIS WARRANTY SHALL NOT COVER ADJUSTMENT OF CUSTOMER OPERATED CONTROLS AS EXPLAINED IN THE APPROPRIATE MODEL'S INSTRUCTION MANUAL OR PRODUCTS WHICH HAVE BEEN ALTERED, ABUSED, OR HAVE MISSING OR ALTERED SERIAL NUMBERS.

2. THIS WARRANTY SHALL NOT APPLY TO UNCRATING, SETUP, INSTALLATION, OR THE REMOVAL AND REINSTALLATION OF PRODUCTS AFTER REPAIR.

3. THIS WARRANTY SHALL NOT APPLY TO REPAIR OR REPLACEMENTS NECESSITATED BY ANY CAUSE BEYOND THE RESULT OF

MEMO

Abstract black curved shape on white background (no text or symbols)