CVC6146SCSFF - Security Camera Speco Technologies - Free user manual and instructions

USER MANUAL CVC6146SCSFF Speco Technologies

540 Line Color Dome Camera

Wall & Ceiling Mountable

WARNING & CAUTION

CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER (OR BACK). NO USER SERVICIABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

The lighting flash with an arrowhead symbol, within an equilateral triangle is intended to start the user to the presence of un-insulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (serving) instructions in the literature accompanying the appliance

- Contents

Package Contents 3

Precautions 4

Camera Installation 5

Internal Components 6

Features 8

OSD 9

Operating Your Camera

SET UP 10

SET UP LENS 10

SHUTTER SPEED CONTROL 10

BACK LIGHT 10

AUTO GAIN (AGC) 10

WHITE BALANCE 11

CAMERA TITLE 11

MIRROR 12

DAY/NIGHT/SYNC 12

MOTION DETECTION 12

PRIVACY 12

GAMMA 13

RESET 13

PACKAGE CONTENTS

- Please make sure that the following items are included in the package:

1 CVC6146SCS Series Camera
2 Mounting Screws
1 Video test Connector

Please leave this manual with the end-user for future reference.

COMPATIBILITY

"A" type Box

DFM Series

PRECAUTIONS

• THIS DOME CAMERA SHOULD BE ONLY INSTALLED BY QUALIFIED PERSONNEL
• TO PREVENT A FIRE OR ELECTRICAL HAZARD PLEASE USE PROPER POWER CABLE
- THE DOME COVER SHOULD BE TREATED WITH CARE. DO NOT CLEAN THE COVER WITH AN ABRAISIVE CLEANING MATERIAL - PLEASE USE A SOFT CLOTH OR TISSUE TO CLEAN THE DOME COVER
- THERE ARE NO USER-SERVICEABLE PARTS INSIDE. PLEASE DO NOT DISASSEMBLE THIS CAMERA OTHER THAN TO MAKE INITIAL ADJUSTMENTS
- PLEASE USE A UL APPROVED REGULATED 24 VOLT AC OR 12 VOLT DC POWER SUPPLY
- PLEASE USE APPROPRIATE LOW VOLTAGE POWER CABLE TO PREVENT FIRE OR ELECTRICAL SHOCK

CAMERA INSTALLATION

CONNECT POWER CABLE

1. WHEN USING 12 VOLTS DC (constant voltage 500 mA)

1. WHEN USING 24 VOLTS AC (20 Volt Amps)
2. CONNECT ACCESSORY CABLE TO THE POWER JACK AND CONNECT 24V AC TO THE LEAD

1. CONNECT VIDEO CABLE
2. CONNECT BNC CABLE TO THE BNC JACK.

INTERNAL COMPONENTS

1. Mechanical
   

(2) Joy Stick Controller (1) DC Auto iris Lens (2.8-11mm)

(1) DC AUTO-IRIS LENS
Adjust between T←→W (TFI F ←→WIDE) to set the

INTERNAL COMPONENTS

1. Joy Stick

Close-up of a circuit board with two arrows pointing to components (no visible text or symbols)

Video Test Terminal
OSD Joystick Switch

● Features

BLC

When the image is in front of strong background lighting, your camera allows you to get a clear image.

High Resolution

Horizontal resolution of 540 TV lines is

achieved by using a SONY Double Speed CCD with

410,000 pixels, yielding pictures with a high S/N ratio.

OSD

All camera functions are menu driven for easy use.

The camera can show color pictures in all lighting

conditions, or you can have it automatically switch to a B/W

● Operating your camera

OSD Function

LENS ● DO MANUAL SHUTTER ● AUTO FLX FIXED MANUAL ● BLC ● OFF ON ● ACC ● OFF ON ● WHITE BAL. ● ATW ● AWB FDOD MANUAL ● FUNCTION RETURN CAMERA ID ● ON ● OFF MIRROR ● ON OFF DAY NIGHT ● COLOR AUTEBW ● MOTION DET ● ON OFF ITEMACY ● ON OFF

● Operating your camera – SETUP

1) LENS

Selects Lens Type.

2) SHUTTER

Adjusts shutter settings.

Flicker-less mode (FLK) reduces on-screen flickering.

Electronic Shutter Control (AUTO) adjusts brightness level on screen.

Manual mode allows you to adjust the shutter speed.

from1/60\~1/120,000 of a second (NTSC), or 1/50\~1/100,000(PAI).

FLK is the only option available when the camera lens is set to the

recommended DC mode

3) BLC

BLC AREA

ALL CLEAR ALL SET

5) WHITE BAL

Controls color on the screen.

Select Auto Tracking White Balance (ATW) when the color

lamp. is 2400°K\~12000°K (for example when under a fluorescent

light or outdoors)

Manual mode allows you to increase or decrease the red

or blue factor on screen.

Auto While Balance Control (AWC) automatically adjusts

The white balance to your specific environment.

6) FUNCTION

(8-1) RETURN

Return to the main SFTUP menu.

(6-2) CAMERA ID

ID SETUP

Display a name and/or

(6-3) MIRROR

Produce a horizontal mirror image on screen.

(6-4) DAY / NIGHT

AUTO = Automatically detect color or black/white.

Delay - When the Day & Night function starts or stops (0\~15sec)

Start Level - Set the brightness level where the Day & Night

function start to operate

End Level – Set the brightness level where the Day & Night

FUNCTION stops operate COLOR = Full time color mode

B/W = Full time B/W mode

(6-5) MOTION DET

MOTION

MOTION AREA

AREA SEL Select a motion detection grid (top left, top right, bottom left, bottom right) to modify.

AREA STATE = Activate or deactivate the selected grid.

LEFT/RIGHT/TOP/BOTTOM = Alter the dimensions of the selected grid.

COLOR - Select color of privacy area.

(6-7) GAMMA

Sharpen the image on screen

Excessive sharpening may cause picture noise.

(6-8) LANGUAGE (English / 한국어 / 汉语/漢語 / 日本語)

Choose language that should be displayed

(6-9) RESET

Restore all factory default settings.

7) ADJUST

SPECIFICATIONS

ITEM	CVC6146SCS Series
Power Source	DC12V & AC24V (Dual Voltage)
Image Sensor	1/3", SONY SUPER HAD CCD, 410,000 pixels
Effective Pixels	755(H) x 582(V), 10 * CCD
Maximum Aperture Ratio	1:1.3 ~ 2.0
Scanning System	2:1 Interlaced 525 Lines / 60Fields / 30Frames
Video Output	1.0V [p-p] Composite, 75Ω
Resolution	540 TV Line
Back Light Compensation	AUTO / OFF
Gain Control	ON / OFF
Electric Shutter Speed	1/50 ~ 1/100.000 sec

DIMENSIONS

* SIDE VIEW

30.00 100.00

* TOP VIEW

WARRANTY

LIMITED WARRANTY

THE WARRANTY OF WELCHY (IN THE WORLD'S) AND/OR IN THE WORLD'S AREA

THIS WARRANTY APPLES ONLY TO THE ORIGINAL USER

SOLVENTIONING AND EXCELLEMS FOUND FOR THE SELLATION AGAINST MUSEUM

DEFICING MATERIAL AND WORKSARSHIP FOR THE FOLLOWING PERIOD FOR TWISSE AND LAUNCH

BRIED TECHNOLOGIES DIMENSIONS

SPEED TECHNOLOGIES COMPENSERS SPECO TECHNOLOGIES MONITORS

SPECO TECHNOLOGIES VONIONS:

BALANCE BY SPUS TECHNOLOGIES INC.
JBL LFDs Time Index YCB Group Assembly

HTEARS

I YEAR

1 YEAR

90-DAYS

SPECO TECHNOLOGIES WILL REVE OR REPLACE US OUR DISCRETION ANY PARTS FOUND TO BE DEFECTIVE FOR THE

WARIANG, PETERLY SPECIFIED WE WILL PROVIDE A DES AGMENT FOR ANY DETECTIVE PAIR.

CONDITIONS

1 YOU MUST OBTAIN A RETURN AUTHORIZATION NUMBER FOR ANY MERCHANTISE BEING RETURNED TO

1. YOU MOST CUMBER A RETURN AUTHORIZATION NUMBER FOR ANY MECHANICAL BEING RETORNE SPECO TECHNOLOGIES, WHETHER FOR RESPECTIVE CHAPES OR REPAIR, WHETHER IN OR OUT OF

WARRANTY

RETAINED ON REPLACEMENT PRODUCT WILL BE RETURNED BEFORE DURING THE WARRANTY PERIOD

EXCLUSIONE

1. THIS WARRANTY SHALL NOT COVER ADJUSTMENT OF CUSTOMER OPERATED CONTROLS AS EXPLAINED IN THE APPROPRIATE

MODEL'S INSTRUCTION MANUAL OR PRODUCTS WHICH HAVE BEEN ALTERED, ABUSED, OR HAVE MISSING OR ALTERED SERVICE

12.056-13

\$ THIS WARRANTY SHALL NOT APPLY TO UNICURING OF THE INSTALLATION OF THE REMOVAL AND INSTALLATION

OF NOODLES AFTER THE TAW

1. THE WASHWATER'S NAME OF CHINA RESEARCH AND INFORMATION AND INFORMATION AND INFORMATION

2. THIS INVESTMENT OF THE TAX LEAF TO REHIND ON THE END OF THE SECURITIES OF TAX GROWTH BEFORE THE LEVEL OF INFLUENCE INCLUDING BUT NOT LIMITED TO ANY MALIGNANCE, OBPECTS OR FUTURE CAUSED BY OR RESULTING FROM

UNAUTHORIZED SERVICE OR PARTS, IMPROPER MAINTENANCE, MODIFICATION OR RERAIN BY THE USER ABUSE UNUSE, NEJECT

ACCIDENT: FIRE, FLOOD, OR OTHER ACTS OF NATURE, INCORRECT LIME VOLTAGE. DAMAGE OR MADE BURNS TO TELEVISION

MEMO

speco technologies®