O5MDP1W - Security Camera Speco Technologies - Free user manual and instructions

USER MANUAL O5MDP1W Speco Technologies

Close-up of a white spherical security camera with 'speco technologies' branding on the dome (no other text or symbols visible)

Directions

Be careful not to cause any physical damage by dropping or throwing the camera.

Especially keep the device out of reach from children.

Do not disassemble the camera. No after service is assumed when disassembled.

Use only power adapters compatible with the unit.

Be careful to prevent moisture or water penetration into the unit. Particular attention is needed when installing the unit. The screw holes for the installation screws and pipe should be maintained water tight during the whole life time of the product.

All the electrical connection wires running into the unit should be prepared so that water from the outside cannot flow into the unit through the surface of the wires. Penetration of the moisture through the wire for extended period can cause malfunction of the unit or deteriorated image.

Note

This equipment has been tested and found to comply with the limits for a Class A digital device pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generate, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Revision History

Date	Revision	Details
Sep 13 ^th , 2013	1.0	First manual revision creation.
Nov 7 ^th , 2013	1.1	Text revisions

Contents

1. Introduction......5

1.1. Overview 5
1.2. Specification 6
1.3. Applications of O5MDP1....7

1. Product Description 8

2.1.Contents 8
2.2. Product Preview 8
2.3. Physical description....9

2.3.1. External View....9
2.3.2. Dimension....9
2.3.3. External Connector....10
2.3.4. Factory Default Switch 10
2.4. Functional Description....11

1. On Site Installation 13

2. Getting Started....14

4.1. PC Requirement 14
4.2. Quick Installation Guide....14

1. Introduction

1.1. Overview

The O5MDP1 is panoramic IP camera offering panoramic view of 360° or 180° for covering entire surveillance area with a single IP camera. 5 Mega Pixel image from Panomorph camera module can replace up to 4 PTZ cameras and 5 fixed cameras. It enables real time transmission of synchronized video of up to 2,592x1,944(10fps) video and audio data. Remote clients can connect to O5MDP1 for the real time video/audio data through various client solutions running on PC or smart device. Real time 2-way communication is available through bidirectional audio communication feature.

Designed to be a stand-alone streaming audio & video transmission device, O5MDP1 can be applied to various application area such as video security, remote video monitoring, distance education, video conference or internet broadcasting system.

Vandal proof and weather proof housing will extend the application area to harsh environment of wide temperature range. Embedded PoE (Power over Ethernet, IEEE 802.3af) will enable the owner to reduce the total cost of ownership by reducing on-site wiring works for the installation.

1.2. Specification

Category	Sub-Category	Details
Video	Compression	H.264 / MJPEG
	Resolution	2592 x 1944
Audio(Bi-directional)	Up	32 Kbps G.726
	Down	64 Kbps PCM
Network	Interface	RJ-45, 10/100 Mbps
	Access network	Static, DHCP, PPP/PPPoE
	Application	RTP, RTSP, SMTP, FTP, HTTP, SDP, NTP, DNS
I/O	Sensor In	1	NC, NO Selectable
	Relay Output	1
	RS-232C	N/A
	Mic/Line In	Selectable in Admin page
	Line Out	1 V p-p output for amplified speaker
Power Supply	PoE	Power over Ethernet (IEEE 802.3af)
	DC Adapter	12V DC adapter (1 Amp)
Housing	IP66 compliant
Motion Detection	3 zones	Arbitrary shape with independent sensitivity
Upgrade	Firmware upgrade over IP network
Administration	Remote administration over IP network
	Web Viewer	Internet Explorer 8 and up

1.3. Applications of O5MDP1

• Security surveillance (buildings, stores, manufacturing facilities, parking lots, banks, government facilities, military, etc.)
• Remote monitoring (hospitals, kindergartens, traffic, public areas, etc.)
  • eleconference (Bi-directional audio conference). Remote Learning, Internet broadcasting
  • Weather and environmental observation

2. Product Description

2.1. Contents

The product package contains followings :

Contents	Description	Remarks
O5MDP1	IP camera O5MDP1 main unit
Accessories	CVBS Cable 1EA,Screws (3 pieces of 1 type),Anchors (3 pieces of 1 type),L-type wrench with six angles 1EA
CD	Software & User's Guide
Quick Reference Guide	Quick installation guide
Power Adaptor	Default built in standard PoE module(IEEE802.3af)	12V DC Adaptor(Optional item)

2.2. Product Preview

2.3. Physical description

2.3.1. External View

Close-up of a metallic spherical security camera with a dome and lens (no visible text or symbols)

Figure 2-1. External view of O5MDP1

2.3.2. Dimension

Unit: mm

2.3.3. External Connector

Network (LAN) Mic/Line Input Power Line Output Sensor Input (white(+), Red(-)) Relay Output (Black(+), Yellow(-))

Figure 2-3. Connector for external connection

2.3.4. Factory Default Switch

Factory default switch is provided for returning the IP camera to factory default state. Unscrew the cover to access the switch. There are two functions assigned to factory default switch.

1. Returning to Factory Default State: Press the switch about 5 seconds while power is applied to return to factory default state.

2.4. Functional Description

• Power : Power input for supplying 12V DC, 1A power.

Caution : If OSMDP1 is powered by PoE, do not plug in DC Jack with active DC power into DC power connector.

- Network (LAN)

100Mbps Ethernet connector (RJ-45) with PoE standard (802.3af). LED on the Ethernet connector shows the status of O5MDP1 as the followings:

- Status LED (It will be lit in green or red depending on the status)

① Green : Green color indicates that the camera is in normal operation mode. Continuous green indicates that data transmission is possible. Blinking green means that someone is connected to O5MDP1.

② Red : Continuous or blinking red indicates that hardware is in abnormal condition.

LED will be lit with red momentarily and it will be lit with green after a while when power is applied into O5MDP1

- Micro SD Card slot

Please insert SD memory card when you want to use SD memory card. In case of pulling out SD memory card, please push the SD card.

- Relay Output

Relay output is provided for connecting alarm devices or for remote on/off control of devices such as light. Relay is normal open and it will be closed upon alarm annunciation or remote on. The relay is capable of switching 30V AC/DC, 2A. For the application which needs power switching beyond this limit, use additional relay switch as shown in the right of Figure 2-5.

graph TD
    A["Relay"] --> B["Alarm Out Device"]
    A --> C["Power Supply ( ~30V) ( ~2A) (DC/AC)"]
    D["Relay"] --> E["Optional Relay Switch"]
    D --> F["Power Supply ( ~30V) ( ~2A) (DC/AC)"]
    G["Power Supply (30V~ ) (2A~) (DC/AC)"] --> H["Alarm Out Device"]

* Left : switching requirement below 30V, 2A

* Right : switching requirement higher than 30V, 2A. Apply this connection when either voltage or current exceed the limit.

Figure 2-5. RELAY Output connection

- Sensor Input

Connect external alarm sensor. Examples of sensing devices are infrared sensor, motion sensor, heat/smoke sensor, magnetic sensor, etc. Connect the two wires of the sensors to "Sensor Input". The sensor type(NC/NO) can be set in admin page. Multiple sensor devices can be connected in parallel.

3. On Site Installation

Use cables and conduits that are suitable for the installation. Particular attention should be paid in the installation so that no moisture is allowed to penetrate into the unit through the cables or conduits during the life time of the product. Products of which the internal parts are exposed to moisture because of improper installation are not covered by warranty

1. Remove the top cover.
2. Fix the base on the wall or ceiling.

Technical line drawing of two mechanical components with internal bearing housing (no text or symbols)

1. Adjust the rotational position of the camera for desired viewing of the site.

4. Getting Started

Brief information for first time operation of O5MDP1 is provided in this chapter.

4.1. PC Requirement

Audio/Video streaming data received from O5MDP1 can be displayed or stored in a PC running client programs.

Minimum requirement of the PC is described below:

ITEM	Minimum Requirement	Recommended Specification
CPU	Intel Core i3 3Ghz	Intel Core i7
Main Memory	2GB	4GB
Operating System1	Windows XP	Windows 7 (64bit)
Web Browser	Internet Explorer 8, 9	Internet Explorer 8, 9
Graphic Card	Video RAM 256MBResolution 1920x1080	Video RAM 1GBHigher than 1920x1080
Network	100 Base-T Ethernet	100 Base-T Ethernet

graph LR
    A["Computer"] --> B["LAN switch"]
    B --> C["LAN switch with standard POE"]
    C --> D["Monitor"]
    D --> E["DC adaptor"]

Figure 4-1. Power and network connection

4.2.2. Install Speco-NVR and set IP parameters on O5MDP1

Speco-NVR is a multi-channel VMS program for the IP camera. Install Speco-NVR on remote PC to connect to these products. It is needed to assign connection information to Speco-NVR program before connection. Insert the CD provided with product into the PC and install Speco-NVR.

Admin Page Button ONSIP Installer

O5MDP1 Owner's Manual

IP Installer MAC Address IP Address Name No Refresh Set Admin Page Reboot Default Adapter About Exit 1 2 3 4 5 6 7 8 9 10 MAC Address System Name Management Server Net. Mode Static Web Port RTSP Port HTTP Streaming Clone MAC IP Address Subnet Mask Gateway DNS1 DNS2 Service Name User Name Password Static ADSL(PPPoE) Auto(DHCP) WLAN Radio 802.11b WLAN SSID Auth. Type EncryptType WLAN Key Network Adapter

4.2.3. Remote video connection to O5MDP1

1. Connection through Web Viewer

Web Viewer offers simplest way of video connection to O5MDP1. For video connection, enter the IP address of O5MDP1 in the URL window of Internet Explorer as:

[e.g.] Port 80

Can be omitted the default port of 80

[e.g.] Port 8080

Note : Active-X module should be installed on your PC before actual connection. If your PC is not connected to the internet, you cannot download Active-X module. Most convenient way of installing the Active-X module is installing Speco-NVR which is available from the CD or our web site.

Connection to Admin Page Basic Control

O5MDP1 Owner's Manual

2. Connection through Speco-NVR

Click the camera assignment button for setting the camera address. Input the description, address, Ch#, User ID, Password and port and then click the save button. After assignment procedure, you must click the SAVE button. You can see the live video when you click the live view button as below. When you exit Speco-NVR, you have to input the ID/PW, admin/1234. Details for Speco-NVR can be found in [Speco-NVR User's Guide].

Camera Assignment Live view Exit Program ID Password Exit Program Default ID/PW: admin/1234 speco technologies Address Manager Camera Assignment

4.2.4. Additional settings through connection to the Admin Page

All parameters of the camera are factory default out of the box. For a more sophisticated target application, parameters need to be changed through the admin page. The admin page can be connected through

"http://IP_Address:Port_Number/admin.htm"

ID and password of the administrator are required. Default ID and password are "admin", "1234". It is highly recommended to change the ID and password to prevent illegal access to the IP camera. For more detailed information, Please refer to the "Configuration_Guide" Guide.

4.2.5. Panoramic viewing through Speco-NVR

Panoramic viewing is supported by Speco-NVR. O5MDP1 can be installed on the ceiling or wall. In case of ceiling mount 360° panoramic view is offered, while 180° panoramic view is offered for wall mounting. To select the mounting position of the camera, "Panomorph View Type", "Panomorph Cam Position" from the pop-up menu when right mouse button is clicked on the display window of Speco-NVR.

Quad PTZ Panomorph View Type Panomorph Compcation Panomorph Control Layer Step(s) Camera Assignment(1) Camera Active Start Turning Digital PTZ View Longfall Sum View PowerPower Voice Control RVD Control System Controller PTZ (control) Show Information Display US Lock Perimeter PTZ Speco technologies

Figure 4-4. Speco-NVR Pop-up menu (Panomorph sub-menus)

• Panomorph View Option

	PTZ mode	Quad mode	Perimeter mode	Perimeter mode(wall)

5. Trouble Shooting

5.1. No power is applied

- In case of Standard PoE (Power over Ethernet)

Power supply through standard PoE is possible only when the following conditions are met.

1. Standard PoE is supported on the product.
2. The LAN switch supports standard PoE.

Make sure that both the IP camera and the LAN switch support standard PoE (IEEE 802.3af)

• In case of DC adaptor

If PoE is not applied, the power and network connection should be made through separate cables. It is recommended to use DC adaptor supplied by provider for the feeding of the power. In case of replacing the DC power supply, make sure that the power supply meets with the power requirement of the IP camera to prevent damage or malfunction.

5.2. Cannot connect to the Video

Check the status of the network connection through PING test.

Try the following on your PC :

• Start > Run > Cmd > Ping IP address (Ex : Ping 172.16.42.51)
• If "Reply from \~" message is returned (① in the figure below), the network connection is in normal state. Try connection to the video again. If the problem persists, or refer to other trouble shooting notes.
• If "Request timed out" message is returned. (② in the figure below), the network connection or network setting is not in normal state. Check the network cable and settings.

C:\WINDOWS\System32\cmd.exe Microsoft Windows XP [Version 5.1.2600] (C) Copyright 1985-2001 Microsoft Corp. C:\Documents and Settings\Superman\ping 172.16.42.51 Pinging 172.16.42.51 with 32 bytes of data: Reply from 172.16.42.51: bytes=32 time(ies TTL-64) Reply from 172.16.42.51: bytes=32 time(ies TTL-64) Reply from 172.16.42.51: bytes=32 time(ies TTL-64) Reply from 172.16.42.51: bytes=32 time(ies TTL-64) Ping statistics for 172.16.42.51: Packets: Sent - 4, Received - 4, Lost - 0 (kx loss), Approximate round trip times in milli-seconds: Minimum - One, Maximum - One, Average - One C:\Documents and Settings\Superman>

5.3. Windows Vista or Windows 7

Windows Vista and Windows 7 users need to configure UAC (User Access Control) and Privilege Level for proper recording and still video capture in Speco-NVR and Web Viewer.

1. UAC (User Access Control) configuration

1) Double-click "User Accounts" in control panel
2) Double-click "Turn User Account Control on or off"
3) Uncheck "Use UAC to help protect your computer"

1) Control Panel User Accounts System and Maintenance Security Windows and Internet Maintenance and Network Properties User Accounts Accounting and Preensions Text Language and Remote Search of Accounts Additional Options Close Page 2) Control Panel User Accounts User Accounts 3) Make changes to your user account Create a password for your account Change your account Change your account home Change your account type Make changes to your account Turn User Account Control to use PC 3) Turn User Account Control (UAC) to make your computer more secure Use Account Control (UAC) can help prevent unauthorized changes to your computer. We recommend that you first UAC, then to help prevent your computer. If the User Account Control (UAC) is needed to protect your computer.

Open Troubleshoot compatibility Open file location Run as administrator Pin to Taskbar Pin to Start Menu Restore previous versions Send to Cut Copy Create shortcut Delete Rename Properties

ANB Properties Security Details Previous Versions General Shortcut Compatibility If you have problems with this program and it worked correctly on an earlier version of Windows, select the compatibility mode that matches that earlier version. Help me choose the settings Compatibility mode Run this program in compatibility mode for: Windows XP (Service Pack 3) Settings Run in 256 colors Run in 640 x 480 screen resolution Disable visual themes Disable desktop composition Disable display scaling on high DPI settings Privilege Level Run this program as an administrator Change settings for all users OK Cancel Apply

1. UAC (User Access Control) configuration

1) Double-click "User Accounts" in control panel
2) Double-click "Change User Account Control setting"
3) Set to "Never notify"

2. Privilege Level Control

1) Select "NVR" icon on the desktop
2) Click right mouse button and select "properties"
3) Check "Privilege Level" in "Compatibility" tab

Open Troubleshoot compatibility Open file location Run as administrator Pin to Taskbar Pin to Start Menu Restore previous versions Send to Cut Copy Create shortcut Delete Rename Properties

AVR Properties Security Details Previous Versions General Shortcut Compatibility If you have problems with this program and it worked correctly on an earlier version of Windows, select the compatibility mode that matches that earlier version. Help me choose the settings Compatibility mode Run this program in compatibility mode for: Windows XP (Service Pack 3) Settings Run in 256 colors Run in 640 x 480 screen resolution Disable visual themes Disable desktop composition Disable display scaling on high DPI settings Privilege Level Run this program as an administrator Change settings for all users OK Cancel Apply

5.4. Technical Assistance

If you need any technical assistance, please contact your dealer. For immediate service please provide the following information.

1. Model name
2. MAC address and Registration number
3. Purchase date
4. Description of the problem
5. Error message

Appendix A – Important Notice in Exchanging SD Card (Micro SD)

SD Card is a non-volatile memory device for storing video and audio data on the product. Continued writing to the SD Card will cause wear-off of the memory cell.

When you plug out the SD Card for replacement or other purpose, follow the steps below in order to prevent data loss or crash of the SD Card.

1. Press factory default button for 1 sec to unmount the SD Card.

- SD Card can also be unmounted by going to Admin Page -> Sensor&Capture Setup and clicking on CONFIRM button at the right of SD Card Unmount menu.

1. Unplug the SD Card

- If no action is taken within 1 minute, SD Card will be mounted again.

1. Plug in new SD Card

2. If the SD Card is a new one for the IP camera, format the SD Card by following through the steps below.

- Go to Admin Page -> Sensor & Capture Setup

- In the SD Card management menu, click on CONFIRM button at the right of SD Card Format.

For more detailed information regarding connection to admin page,