HTINTB8HW - Security Camera Speco Technologies - Free user manual and instructions

USER MANUAL HTINTB8HW Speco Technologies

(Weatherproof Dome Camera with Chameleon™ Cover)

HTINTB8H / HTINTB8HW

(Weatherproof Bullet Camera with mount plate)

HTINTD8H / HTINTD8HW

(Weatherproof Dome Camera)

Contents

① Contents....1
- Precautions....2, 3
Safety Instructions 4
● Package Contents......5
● Camera Installation....6-11
Specifications....12-14
● Camera Dimension 15,16

Precautions

Do not install the camera in extreme temperature condit

Illustration of two cartoon-style surveillance cameras emitting flames with a cloud above (no text or symbols)

Only use the camera under conditions where temperatures are between -10°C and +50°C. Be especially careful to provide ventilation when operating under high temperatures.

Do not install the camera under unstable lighting conditions.

Severe lighting change or flicker can cause the camera to work improperly.

Do not touch the front lens of the camera.

This is one of the most important parts of the camera. Be careful not to leave fingerprints on the lens cover.

Never keep the camera pointed directly at strong light.

Illustration of a sun shining on a surveillance camera and a helmet, both showing expressive faces (no text or symbols)

Do not drop the camera or subject it to physical shocks.

Illustration of two surveillance cameras with smoke, emitting exhaust smoke from a puddle (no text or symbols)

Do not expose the camera to radioactivity.

It can cause malfunctions to occur. If exposed Housing Availability is CCOPromise

CAUTION RISK OF ELECTRIC SHOCK DO NOT GEARL CAUTION TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER OR BACK. NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. ISO14001 CE FC

The lightning flash with an arrowhead symbol, within an equilateral triangle is intended to alert the user to the presence of uninsulated dangerous voltage within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.

In USA and Canada, Use Class 2 Power Supply Only

INFORMATION - This equipment has been tested and found to comply with limits for a Class A digital device, pursuant to part 15 of the FCC Rules & CE Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at

Safety Instructions

Precautions for use

① This camera should be installed by qualified personnel only
There are no user serviceable parts inside
Do not disassemble this camera other than to make initial adjustments
Use a UL approved regulated 24 volt AC or 12 volt DC power supply
- Use appropriate low voltage power cable to prevent fire or electrical shock
Please insure that your installation area can support the weight of the camera

Please handle this camera carefully :

Do not use a strong or abrasive detergent when cleaning the camera
- Do not install near cooling or heating device

Package Contents

Please make sure that the following items are included in the Package:

1) HT7246H

• 1 Video Test Connector, Power Jack
• 1 Chameleon Cover
• 1 Wrench
- Set Screw
- 3 Tapping Screws 4x40
- 3 Plastic Anchor

2) HTINTB8H, HTINTB8HW

• 1 Video Test Connector, Power Jack
- 1 Bracket Base
- 2 Wrenches
- Set Screw
- 4 Tapping Screws 4x25
- 4 Hexagon Socket Screws 5x10

3) HTINTD8H, HTINTD8HW

• 1 Video Test Connector, Power Jack
- 2 Wrenches
- Set Screw
- 3 Tapping Screws 4x25
- 2 Hexanon Socket Screws M6x20

CAMERA INSTALLATION

CONNECT POWER CABLE

1. WHEN USING 12 VOLTS DC (constant voltage 500 mA)

Power Input :RED Center : (+) DC 12V Power Supply

1. WHEN USING 24 VOLTS AC (40 Volt Amps)

RED(+) BLACK:(-) AC 24V Power Supply

1. CONNECT VIDEO CABLE

- CONNECT BNC CABLE TO THE BNC JACK.

CAMERA INSTALLATION

Compatibility

1) HT7246H

INTWM INTPM CVCJBD DFM

2) HTINTB8H, HTINTB8HW

CVCJBB

INTJBS

INTCM

CAMERA INSTALLATION

Compatibility

3) HTINTD8H, HTINTD8HW

INTWM INTPM JB03TG

CAUTION : The installation instructions in this manual are for use by qualified service personnel only. To reduce the risk of electric shock, do not perform any servicing other than that contained in the operating instructions unless you are qualified to do so.

CAMERA INSTALLATION

1. HT7246H

PLASTIC ANCHOR 6x30, 3EA VANDAL DOME BASE ASSEMBLY TAPPING SCREW 4X40, 3EA

CAMERA INSTALLATION

1. HTINTB8H, HTINTB8HW

CAMERA ASSEMBLY BASE ADAPTOR BRACKET

CAMERA INSTALLATION

3. HTINTD8H, HTINTD8HW

DOME BASE TAPPING SCREW 4X25, 3EA DOME ASSEMBLY

960H Intensifier3

(Weatherproof Dome Camera with Chameleon™ Cover)

DC Auto Iris Varifocal Lens 2.8-12mm

Close-up of a metallic security camera dome (no visible text or symbols)

HT7246H

SPECIFICATIONS

MODEL	HT7246H
Image Pick-Up Device	1/3" 960H Sony Super HAD CCD
TV System	NTSC, PAL
Total Pixels	NTSC=1020(H) * 508(V) / PAL=1020(H) * 596(V)
Effective Pixels	NTSC=976(H) * 494(V) / PAL=976(H) * 582(V)
Scanning Frequency	NTSC=15.734KHz(H) & 59.94Hz(V) / PAL=15.625KHz(H) & 50.00Hz(V)
Scanning System	2:1 Interface
Synchronization	Internal
Resolution	700TV Lines
Minimum Illumination	CDS OFF: 0.15 Lux, CDS ON: 0.00002 Lux

960H Line Intensifier3

(Weatherproof Bullet Camera with mount plate)

DC Auto Iris Varifocal Lens 2.8-12mm

Exterior view of a metallic security camera with mounted lens and mounting flange (no text or symbols visible)

HTINTB8H
HTINTB8HW

SPECIFICATIONS

MODEL	HTINTB8H / HTINTB8HW
Image Pick-Up Device	1/3" 960H Sony Super HAD CCD
TV System	NTSC, PAL
Total Pixels	NTSC=1020(H) * 508(V) / PAL=1020(H) * 596(V)
Effective Pixels	NTSC=976(H) * 494(V) / PAL=976(H) * 582(V)
Scanning Frequency	NTSC=15.734KHz(H) & 59.94Hz(V) / PAL=15.625KHz(H) & 50.00Hz(V)
Scanning System	2:1 Interlace
Synchronization	Internal
Resolution	700TV Lines
Minimum Illumination	CDS OFF: 0.15 Lux, CDS ON: 0.00002 Lux

960H Line Intensifier3

(Weatherproof Dome Camera)

DC Auto Iris Varifocal Lens 2.8-12mm

Close-up of a gray security camera with lens and frame (no visible text or symbols)

HTINTD8H
HTINTD8HW

SPECIFICATIONS

MODEL	HTINTD8H / HTINTD8HW
Image Pick-Up Device	1/3" 960H Sony Super HAD CCD
TV System	NTSC, PAL
Total Pixels	NTSC=1020(H) * 508(V) / PAL=1020(H) * 596(V)
Effective Pixels	NTSC=976(H) * 494(V) / PAL=976(H) * 582(V)
Scanning Frequency	NTSC=15.734KHz(H) & 59.94Hz(V) / PAL=15.625KHz(H) & 50.00Hz(V)
Scanning System	2:1 Interface
Synchronization	Internal
Resolution	700TV Lines
Minimum Illumination	CDS OFF: 0.15 Lux, CDS ON: 0.00002 Lux

CAMERA DIMENSION

1) HT7246H

5.10" dia 1.16" 3.46" 3.93" dia

5.10° dia

2) HTINTB8H, HTINTB8HW

CAMERA DIMENSION

3) HTINTD8H, HTINTD8HW

5.47" dia

4.36" 3.34" 3.70"

FEATURES

Now with "PRESETS"

PRESETS (Outdoor, Indoor, Elevator, Lobby, Hallway & Low Light) Used for a quick and easy setup for the installation environment.

700TVL Resolution

Horizontal resolution of 700 TV lines is achieved by using a SONY Super-HAD CCD with 520,000 pixels, and a custom DSP yielding pictures with a high S/N ratio.

INTENSIFIER 3

More Powerful Performance in low light condition. High quality Pictures to be captured in very low light condition.

WDR

More Powerful WDR in strong back lighting. Your camera allows you to get a clear image.

CDECO DVD

FEATURES

Motion Detection with Alarm Output

Built in motion detector with adjustable areas of coverage will Send a signal to an external alarm device when motion is detected.

Privacy Mask

It also has the ability to mask up to 8 areas of the picture where Viewing is not desired. Each zone can be independently programmed via the OSD

Stabilizer

This function removes image jitter that is caused by vibrations in the building and reduces the amount of hard drive space.

Digital Zoom

The picture could be enlarged by this function in digital.

Day/Might

- Preset Mode

SPECO TECH

1.PRESET MODE

2.MAIN SETUP

1. EXIT

INDOOR

RESET

1. Preset : INDOOR / OUTDOOR / LOW LIGHT / HALLWAY / LOBBY / ELEVATOR.

- Used for a quick and easy setup for the installation environment.

- Menu Setup

1. Press the Function Setup switch.

- Main setup menu is displayed on the monitor screen.

MAIN SETUP

1.LENS

2.EXPOSURE

3.WDR

4.WHITE BAL

5.BACKLIGHT

6.SPECO DNR

7.DAY/NIGHT

8.SPECIAL

9.RETURN

DC ←

OFF

ATW

OFF

ON

AUTO

SAVE

- DC: You can adjust the minimum shutter and maximum value of shutter when DC Lens mode is selected.

1. Press LENS to choose from the sub menu items as listed below.

- BRIGHTNESS : Adjusts the video brightness (selectable from 1-70)

- IRIS SPEED : Adjusts Iris control speed of the DC lens. If the control speed is too slow or fast, use this menu to adjust the speed.

- FOCUS ADJ: To adjust the DC lens focus correctly, you must change MODE to ON under the the FOCUS ADJUST menu. Adjust the lens focus and after the lens focus had been adjusted, change MODE to OFF.

MAIN SETUP 1.LENS DC ← 2.EXPOSURE ← 3.WDR OFF

NOTE

■ If color rolling occurs when using a DC lens, set Shutter to ---.

- Exposure Setting

◆BRIGHTNESS : Adjusts the video brightness.
◆SHUTTER : You can select either auto or manual shutter.
* A.FLK : Select this when you see picture flicker, this can happen when the frequency of the local lighting clashes with the camera.
* ESC : Select this to control the shutter speed automatically. If ESC is selected, the shutter speed is automatically controlled depending on the ambient illumination of the subject.
* MANUAL : You can control shutter speed manually. (1/60 \~ 1/120,000)
* --- : Shutter speed is fixed at 1/60 sec. (1/50 sec.)

NOTE

■ When using a DC lens, set the shutter mode to A.FLK if color rolling occurs.

■ When the SHUTTER is set to ESC after selecting Internal Synchronization Type, the picture may become unstable if the camera faces a bright fluorescent light. Therefore, take care when choosing the installation position.
■ When the SHUTTER is set to MANUAL or A.FLK mode, INTENSIFY will be disabled.

◆AGC(AUTO GAIN CONTROL): The higher the gain level, the brighter the screen, but the higher the noise.

* OFF : Deactivates the AGC function.
* LOW : Allows automatic gain control from 5.3dB to 32dB.
* HIGH : Allows automatic gain control from 5.3dB to 37dB.
◆INTENSIFY: When it is night or dark, the camera automatically detects the light level and maintains a clear picture if this mode is activated.
* OFF · Deactivates the INTENSIFY function

• WDR (Wide Dynamic Range) Setting

WDR illuminates darker areas of an image while retaining the same light level for brighter area to even out the overall brightness of images with high contrast between bright and dark areas.

1. When the SETUP menu screen is displayed, select "WDR" by using the Up and Down buttons so that the arrow indicates 'WDR'.
2. Turn on by using the Left/Right buttons and press SETUP to change the WDR level in the sub menu according to the contrast between bright and dark areas.

MAIN SETUP 1.LENS DC ← 2.EXPOSURE ← ► 3.WDR OFF

- White Balance (White Bal) Setting

Use the White Balance function to adjust the screen color.

1. When the SETUP menu screen is displayed, select "WHITE BAL" by using the Up and Down buttons so that the arrow indicates 'WHITE BAL'.
2. Select the desired mode using Up and Down buttons.

NOTE

■ White Balance may not work properly under the following conditions. In this case select the AWC mode.

① When the color temperature of the environment surrounding the subject is out of the control range (ie. Clear sky or sunset).

② When the ambient illumination of the subject is dim.

③ If the camera is directed towards a fluorescent light or is installed in a place where illumination changes dramatically, the White Balance operation may become unstable.

• BLC(Back Light Compensation) Setting

1. When the SETUP menu screen is displayed, select 'BACKLIGHT' by using the Up and Down buttons so that the arrow indicates 'BACKLIGHT'.

MAIN SETUP 1.LENS DC ← 2.EXPOSURE ← 3.WDR OFF 4.WHITE BAL ATW 5.BACKLIGHT OFF 6.SPECO DNR ON ← 7.DAY/NIGHT AUTO ← 8.SPECIAL ← 9.RETURN SAVE

1. Select a desired mode using the Left and Right buttons depending on the camera

2. Select a desired mode using the Left and Right buttons and press the SET button.

◆BLC : Select 'BLC' to adjust the area to be enhanced then adjust the level.
◆HLC : Enable the user to change the level limit, mask color/tone and area.

NOTE

■ Because there can be a difference in the effectiveness of HLC according to the amount of light area in the screen, optimize the installation angle for the best HLC performance.
■ When dark, the HLC is only activated when a bright light exceeding a specific size in NIGHT ONLY mode.
■ The HLC is not activated in day light or when bright light is not present at night in NIGHT ONLY mode.
■ BLC Function doesn't work in the B/W mode of the DAY/NIGHT menu.

- SPECO DNR Setting

This function reduces the background noise in a low luminance environment.

1. When the SETUP menu screen is displayed, select "SPECO DNR" by using the Up and Down buttons so that the arrow indicates 'SPECO DNR'.

MAIN SETUP

1.LENS

2.EXPOSURE

3.WDR

4.WHITE BAL

- Day/Night Setting

You can display pictures in color or black and white.

1. When the SETUP menu screen is displayed, select "DAY/NIGHT" by using the Up and Down buttons so that the arrow indicates 'DAY/NIGHT'.

MAIN SETUP 1.LENS DC 2.EXPOSURE 3.WDR OFF 4.WHITE BAL ATW 5.BACKLIGHT OFF 6.SPECO DNR ON 7.DAY/NIGHT AUTO 8.SPECIAL 9.RETURN SAVE

1. Select a desired mode using the Left and Right buttons according to the picture display you want.

◆ EXTERN : This mode allows you to supply a desired filter to external signals.
◆ COLOR : The picture is always displayed in color.
◆ B/W :The picture is always displayed in black and white.

You can turn on or off the burst signal on B/W mode.

▲ AUTO TI 1 ' '1 | 1c | 1' 1 ' '1 , '1 , inaul

- BURST MODE : You can turn on or off the burst signal on B/W mode.

- DURATION : You can select the brightness level at which the camera switches from day to night mode.

- DWELL TIME : You can select the duration the camera changes from day to night mode and night to day.

(NTSC MODE)

	COLOR→B/W	B/W→COLOR
FAST	2 lux	5 lux
SLOW	1 lux	5.5 lux

NOTE

■ When using a Video Auto Iris Lens, if you set the lens level to low, automatic switching between Color and Black&White may not occur.
■ When AGC in the EXPOSURE menu is 'OFF', '-' mode operates as 'COLOR' mode and 'AUTO' mode cannot be selected.

- Special Setting

1. When the SETUP menu screen is displayed, select 'SPECIAL' by using the Up and Down buttons so that the arrow indicates 'SPECIAL'.

2. Select a desired mode using the Left and Right buttons.

SPECIAL ▶ 1.IMAGE ADJ ← 2.CAM TITLE OFF 3.SYNC INT 4.MOTION OFF 5.PRIVACY OFF 6.DIS OFF 7.RETRUN ← BASIC

◆IMAGE ADJ.:

1) When the SPECIAL menu screen is displayed, select 'IMAGE ADJ' by using the Up and Down buttons so that the arrow indicates 'IMAGE ADJ'.
2) Select a desired mode using the Left and Right buttons.

IMAGE SETUP ▶ 1.MONITOR LCD 2.REVERSE OFF 3.PIP OFF 4.D-ZOOM OFF 5.FONT COLOR BLUE 6.SHARPNESS ON 7. LANGUAGE ENGLISH

* FONT COLOR: You can change the OSD font color.
* SHARPNESS: As you increase this value, the picture outline becomes stronger and clearer. Adjust this value appropriately depending on the sharpness of the picture.
* LANGUAGE: You can select the menu language.
- NTSC : Korean, English, French, Spanish, Japanese, Portuguese.
- PAL : English, Chinese, German, Italian, French, Spanish, Russian, Serbian, Swedish, Danish, Turkish, Portuguese.
* RETURN: Select this to save the settings for the IMAGE ADJ menu and to return to the SPECIAL menu.

NOTE

■ When the REVERSE mode is enabled, the text on the screen will not flip.

■ If you increase the SHARPNESS level too high, the picture may become distorted or noise may appear.

◆CAM TITLE : If you enter a title, the title will appear on the monitor.

1) If the SPECIAL menu screen is displayed, use the Up and Down buttons so that the arrow indicates 'CAM TITLE'.
2) Set it to 'ON' by using the Left and Right buttons.
3) Press the SET button.
4) Use the 4 direction buttons to move to a desired letter and select the letter by pressing the SET button. Repeat this to enter multiple letters. You can enter up to 15 letters.
5) Enter a title, move the cursor to 'POS' and press the SET button. The entered title appears

NOTE

■ When the CAM TITLE menu is 'OFF', no title will be displayed on the monitor screen even if you enter one.
■ Only English is available in this mode.
■ If you move the cursor to CLR and press the SET button. To edit a letter, change the cursor over the letter to be edited, move the cursor to the letter to be inserted and then press the SET button.

◆ SYNC : In areas where the supply is at 60Hz, you can synchronize the output phase of multiple cameras using the power synchronization function (Line-Lock) without using a synchronization signal generator.

• INT : Internal Synchronization Type.
  * Press the Function Setup switch.
  * You can select a desired phase from 0 to 359 when select 'phase'.

NOTE

■ When the power is DC12V, the SYNC menu is fixed to the 'INT' mode.

♦MOTION : This camera allows you to observe movement of objects in 8 different areas on the screen, and the words 'MOTION DETECTED' appear on the screen when movement is detected.

• ALARM OUT : Trigger the signal from the Alarm Output Terminal of the camera when an object's movement matched a custom motion type.
• DETECT AREA : Defines the motion detection area.
• MASK AREA : Specify a detection exception area to mask. Select a mask area number and specify the size and position.
  * AREA : Select up to 4 areas
  * MODE : Turn the selected area ON or OFF.
  * TOP/BOTTOM/LEFT/RIGHT : Adjust the size and position of the selected area.
  * RETURN : Select this to save the mask area menu settings and return to the MOTION menu.
• SENSITIVITY : Set the sensitivity of the motion detection. The higher the level, the motion detection sensitivity is increased to recognize smaller movements.
• DET. SIZE : Selects an object size to detect on the screen. The higher the level means the larger the detection size.
• RETURN : Select this to save the motion menu setting and return to the special menu

DETECT AREA

1.TOP 1

2.BOTTOM 50

3.LEFT 1

4.RIGHT 50

5.RETURN

◆PRIVACY : Mask an area you want to hide on the screen.

1) When the SPECIAL menu screen is displayed, press the Up and Down buttons so that the arrow indicates 'PRIVACY'.

2) Set up the mode using the 4 direction buttons.

- AREA SEL : You can select up to 12 PRIVACY areas.

- MODE : Turn the selected area ON or OFF.

- MASK COLOR : Determine area color. Select GREEN, RED, BLUE, BLACK, WHITE and GRAY.

- TRANSPARENCY : Add or remove transparency from the masked area.

- SEL POS : Adjust the size and position of the selected area.

- X POS

- Y POS

- RETURN : Select this to save the PRIVACY menu settings and return to the SPECIAL menu.

PRIVACY AREA SETUP

1.AREA	AREA1
2.MODE	OFF
3.MASK COLOR	GREEN
4.TRANSPARENCY	OFF
5,SEL POS	L_TOP
6.X POS	10
7.Y POS	10
8.RETURN ←

◆DIS (Digital Image Stabilizer) :

- Exit Setting

Select a desired EXIT mode using the Left and Right buttons depending on the camera purpose.

• SAVE : Save the current settings and exit the MAIN SETUP menu.
• NOT SAVE : Do not save the current settings and exit the MAIN SETUP menu.

• RESET : Resets the camera settings to the factory defaults. Language and Monitor settings are not initialized.

• Trouble Shooting

PROBLEM	POSSIBLE CAUSE
Northing appears on the screen.	Check the power cable, power supply output and video connection between the camera and monitor.
The image on the screen is dim.	Are the camera lens or the lens glass dirty?Clean the lens / glass with a soft clean cloth.Adjust the monitor controls, as required.If the camera is facing a very strong light, change the camera position.Adjust the lens focus.
The image on the screen is dark.	Adjust the contrast control of the monitor.If there is an intermediate device, correctly set the 75Ω/Hi-z.
The camera is not working properly and the surface of the camera is hot.	Check the camera is correctly connected to an appropriate regulated power source.
Motion Detection is not activated.	Has MOTION DET been set to ON in the menu?Has MD AREA been properly defined?

LIMITED WARRANTY - VIDEO PRODUCTS

THIS WARRANTY IS VALID ONLY ON PRODUCTS PURCHASED AND USED IN THE UNITED STATES OF AMERICA AND CANADA. THIS WARRANTY APPLIES ONLY TO THE ORIGINAL USER.

SUBJECT TO CONDITIONS AND EXCLUSIONS FOUND BELOW, THIS PRODUCT IS WARRANTED AGAINST MANUFACTURING DEFECTS IN MATERIAL AND WORKMANSHIP FOR THE FOLLOWING PERIOD FOR PARTS AND LABOR:

SPECO TECHNOLOGIES CAMERAS .... 5 YEARS

SPECO TECHNOLOGIES IP CAMERAS....2 YEARS

SPECO PTZ AND VL CAMERAS....1 YEAR

SPECO TECHNOLOGIES MONITORS ....1 YEAR

IR LEDS ....90 DAYS

DVRs	3 YEARS
NVRs	3 YEARS
BALANCE OF
SPECO TECHNOLOGIES LINE	1 YEAR

SPECO TECHNOLOGIES WILL REPAIR OR REPLACE (AT OUR DISCRETION) ANY PARTS FOUND TO BE DEFECTIVE FOR THE WARRANTY PERIOD SPECIFIED. WE WILL PROVIDE A REPLACEMENT FOR ANY DEFECTIVE PART.

CONDITIONS

1. YOU MUST OBTAIN A RETURN AUTHORIZATION (RA) NUMBER FOR ANY MERCHANDISE BEING RETURNED TO SPECO TECHNOLOGIES, WHETHER FOR RETURN/EXCHANGE OR REPAIR, WHETHER IN OR OUT OF WARRANTY.

2. THIS WARRANTY WILL BE HONORED ONLY UPON PRESENTATION OF THE ORIGINAL DATED BILL OF SALE OR SALES SLIP

3. TRANSPORTATION OF THE PRODUCT TO OUR SERVICE DEPARTMENT IS THE RESPONSIBILITY OF THE USER. REPAIRED OR REPLACED PRODUCT WILL BE RETURNED PREPAID DURING THE WARRANTY PERIOD.

4. SPECO TECHNOLOGIES DOES NOT AUTHORIZE ANY INTERNET OR MAIL ORDER PRODUCT SALES. IF A SPECO TECHNOLOGIES PRODUCT IS PURCHASED FROM AN UNAUTHORIZED DISTRIBUTOR OR OTHER SOURCE, INCLUDING RETAILERS, MAIL ORDER SELLERS AND ONLINE SELLERS. IT WILL NOT BE HONORED OR SERVICED UNDER THE EXISTING SPECO TECHNOLOGIES WARRANTY POLICY ANY SPECO TECHNOLOGIES PRODUCT PURCHASED FROM THESE ONLINE MERCHANTS WILL VOID THE APPLICABLE WARRANTY AND IS INELIGIBLE FOR TECHNICAL SUPPORT. IF YOU HAVE QUESTIONS ABOUT A RESELLER, PLEASE CONTACT SPECO TECHNOLOGIES AT 1-800-645-5516 FOR A LIST OF UNAUTHORIZED DEALERS, VISIT: www.specotech.com/unauthorized.

EXCLUSIONS

1. THIS WARRANTY SHALL NOT COVER ADJUSTMENT OF CUSTOMER OPERATED CONTROLS AS EXPLAINED IN THE APPROPRIATE Model's INSTRUCTION MANUAL OR PRODUCTS WHICH HAVE BEEN ALTERED, ABUSED, OR HAVE MISSING OR ALTERED SERIAL NUMBERS.

2. THIS WARRANTY SHALL NOT APPLY TO UNCRATING, SETUP, INSTALLATION, OR THE REMOVAL AND REINSTALLATION OF PRODUCTS AFTER REPAIR.

3. THIS WARRANTY SHALL NOT APPLY TO REPAIRS OR REPLACEMENTS NECESSITATED BY ANY CAUSE BEYOND THE RESULT OF MANUFACTURE INCLUDING, BUT NOT LIMITED TO, ANY MALFUNCTION, DEFECTS OR FAILURE CAUSED BY OR RESULTING FROM UNAUTHORIZED SERVICE OR PARTS, IMPROPER MAINTENANCE, MODIFICATION OR REPAIR BY THE USER, ABUSE, MISUSE, NEGLECT, ACCIDENT, FIRE, FLOOD, OR OTHER ACTS OF NATURE, INCORRECT LINE VOLTAGE, DAMAGE OR IMAGE BURNS TO TELEVISION PICTURE TUBES CAUSED BY OR ATTRIBUTABLE TO THE USE OF ANY ACCESSORY, ELECTRONICS GAME OR DEVICE, OR DAMAGE CAUSED TO IMAGE PICKUP DEVICES BY EXCESSIVE LIGHT.

THE PARSOYA OULTURE OF 11 OTHER PARSOYA WARRIERS GROUP NO NOT UNTAGE THE RIGHT TO ZONE FOR THE TW

▶MEMO

▶MEMO

▶MEMO

▶MEMO

speco technologies®

200 New Highway