VLBT6W - Security Camera Speco Technologies - Free user manual and instructions

USER MANUAL VLBT6W Speco Technologies

Collection of white surveillance cameras and security modules (no text or symbols visible)

VLBT5W /VLBT6W/ VLDT5W/VLDT6M/VLT7W

USER MANUAL

Thanks you for purchasing our product. Space Technologies is currently developing and improving products. We reserve the right to modify product design and specifications without notice and without mounting any obligation.

Warnings

■ If the product does not work properly, please contact the dealer or where the product was purchased
Spatco Technologies is not responsible for any problems caused by improper operation or repair.
- Keep away from liquid while in use
■ All installation and operation here should conform to local electrical safety codes.
■ Make sure the power supply voltage is correct before using the camera.
■ Do not drop the camera or subject to physical shock
■ Do not use the device beyond specified voltage range.
■ Do not place the camera in extremely hot, told the opening temperature shall be (-1 F - 122°F), dusty or
damp locations, and do not expose it to high electromagnetic radiation
■ Toroidal heat accumulation, pool certification is required for operating environment

Introduction

This camera series is the latest technology and advanced circuit design, which features high definition and

sensitivity, low noise and distortion and supports HD video transmission with the common central cable.

ecouring the requirement of the H2 monitoring in the additional surveillance system.

High Resolution

Adapt high performance sensor, providing high definition and clear image.

● High Transmission Performance

Real-time transmission with high speed and long distance.

● High Light Compensation (HI.C)

Mask and compensation on the high light area.

DNR

Reduce noise from brightness and color signal.

OSD

Access the camera settings which can be clearly displayed through the main mean.

● White Balance

Adjust the coke temperature according to the environment automatically.

ICR Auto Switch

The filter will filter infrared light during the daytime and change to normal at night to

ensure a high sensitivity and clear image.

● AGC

Adjust the gain of amplifier, enabling the camera to input the standard video signal in different.

lighting condition.

● Wide Dynamic Range (WDR)

When there are both very bright and very dark areas simultaneously in the field of view, this function

will balance the brightness level and powder clear images.

- Privacy Masking

This function allows you to block or mass certain area of a scope for privacy purposes.

● Backlight Compensation (BLC)

When the back of the captureal object is too much bright, you can set BLC for the captureal object to

make it clearer.

● Motion Detection

The alarm will be triggered when there are moving objects captured by the camera.

Cables

Video switch: Remove the cover of the video switch cable and set the video output as below.

Installation

Before you start, please make sure that the wall or ceiling is strong enough to withstand three times

the way to of the camera. Please install and use the cameras in the dry environment.

You'd better install back the lens cover or lower dome less than 4 hours after removing it.

The mounting types of channels are only for reference.

▶Mounting for V1.BT5W/V1.BT6W

1. Drill the screw holes and the cable hole on the wall according to the drill template.

1. Route and connect the cables.

2. Secure the mounting base with camera to the wall with screws as shown below

1. Render adjustment. Before adjustment, preview the image of the camera on a monitor and then loosen the

fixed ring to adjust the view angle of the camera. Lighten the fixed ring after the adjustment.

1. Focus and zoom adjustment (If the amount you get is fixed lens, please skip this step). Remove the

I'll never and then adjust the lacheal and chrom screws in gel to clear image. Finally, hydrogen these two

Lens Cover

▶Mounting for Dome Camera

● Mounting for VLDT6W

1. I cover the screw to open the lower side and then open the back frame to remove the mounting base;

2. Attach the drill template to the place where you want to fix the camera and then drill 4 screw holes

and 1 cable hole if you want to route the cables through the mounting bracket according to the drill

template

1. Reelabed some of the painting base to the ceiling of wall with the screws provisional.

© Fix the camera in the mounting base with the lock screw.

1. Three-axis adjustment: Before adjustment, preview the image of the camera on a monitor and then adjust the camera according to the figure below to get an optimum angle.

1. Install the lower dose back to the camera with the screws and red over the pro te 60 on film easily in a ramp le to the i noad le tin.

● Mounting for VLDT5W

1. Drill the screw holes and the cable hole on the wall according to the drill template.
2. Leosen the screws to remove the lower dome from the camera.

Lower Dome

1. Route and carriage the cables
2. Secure the mounting base with camera to the wall with screws as shown below.

Rubber Plug

1. Three-axis adjustment. Before adjustment, preview the image of the camera on a monitor and then
   adjust the camera according to the figure below to get an optimum angle.
2. Install the lower isome back to the camera and secure it with the screws.

Pun O-353

Rotation (°-355°)

• Mounting for VL17W

1. Drill the screw holes and the cable hole on the wall scanning to the drill template.
2. Route and connect the cables. Then secure the camera to the ceiling or wall with the screws provided.

Rubber Plug

1. Adjust the camera to obtain an optimum angle by locating the lock screws. Before adjustment, preview the image of the camera on a monitor. Tighten the lock screws after you finish adjusting the view angle of the camera

Specifications

Specifications\Models	VLTFSW	VLTFSW	VLTFSM	VLTFSW	VLTFSW
Camera
Image Sensor	12.8" C06/S
Resolution	2MP
Image size	1920-1080
Video Output	AHD-1V/CVC/VBS (Camera colors defaulted to iLD-VI)
Image System	FALN-15C
Electronic Counter	Auto: 1200x-1300000xPAL:1400x-1400000x (NT5C)
IR Distance (bit)	32.8-62.6	68840.5-98.4	32.8-62.6	32.8-62.6
Frame Rate	20fps(50Hz;22fps;50Hz)
Min Illumination	Color:0.001Hz;GFI 2, AGC ON, B/W;Oax with IR
Lens	2.8mm	2.8-12mm	3.8-19mm (corrected)	2.8mm	2.8mm
Lens Mount	M12	T11	T11-M12	M12
S/N Ratio	* Sald(AGC OFF)
Ingress Provision	IP66	IP66	IP66&IX.0	IP66&IX.0	IP66
Functions
Function Control	OSD (UTC control)
Day Rng/ml	DCR
WBH	Yes(120dB)
Digital NR	Yes
Global Exposure	Yes
Central Exposure	Yes
AGC	Yes
Auto White Balance	Yes
BLC	Yes
Front Light Compensation	Yes
Sharpsize	Yes
Smart IR	Yes
Deferring	Yes
ITC	Yes
Image Setting	Yes
Detector Correction	Antio
Other
Power Supply	DC12V (±10%)
Power Consumption	LROFF: <1W, IR 90% : <2W
Working Environment	-4 °F ~ 122°F, 10 % ~ 90% (active stimulus)
Dimensions (inch)	Φ2.75g 0.14	Φ5.43×8.62	Φ5.90×8.49	Φ4.61×3.54	Φ3.43 4.25