HDT471 - Security Camera Speco Technologies - Free user manual and instructions

USER MANUAL HDT471 Speco Technologies

HD-SDI 720/1080P Selectable Traditional Camera with CS Mount Dual Voltage (12VDC / 24VAC)

WARNING & CAUTION

CAUTION

RISK OF ELECTRIC SHOCK DO NOT OPEN

CAUTION : TO REDUCE THE RISK OF ELECTRIC SHOCK

DONOTREMOVECOVER(ORBACK). NOUSERSERVICEABLEPARTSINSIDE REFER SERVICING TO QUALIFIED SERVICEPERSONNEL.

The lighting flash with an arrowhead symbol, within an equilateral triangle is intended to alert the user to the presence of un-insulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons

The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (serving) instructions in the literature accom,ap,ving the appli.ac.

INFORMATION -This equipment has been tested and found to comply with limits for a class A digital device pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiater radio frequency energy and

PACKAGE CONTENTS & INSTALLATION

Please make sure that the following items are included in the package:

1 Camera
1 Wrench
1 Video-Out Cable
1 Power Cable

Back Panel Configuration

graph TD
    A["OSD Joystick"] --> B["CVBS OUT"]
    B --> C["OVBS"]
    C --> D["HD-SDI"]
    D --> E["HD-SDI VIDEO OUT"]
    F["SETUP"] --> G["Central Display"]

FEATURES

1. MEGAPIXEL HIGH RESOLUTION

1/3" 2.1Megapixel Progressive CMOS sensor provides Full HD 1080p video resolution.

2. SENS-UP

Digitally manipulates the exposure level of the image to produce bright images in the darkest of scenarios.

3. DNR (Digital Noise Reduction)

High performance DSP Technology to reduce the gain noise in digital image processing, producing clear sharp images in low light conditions.

4. PIP (Picture in Picture)

When D-Zoom is activated, motion detected picture is shown in inset window.

5. DPC (Defect Pixel Correction)

Detection and correction of defective pixels in

OSD MENU TREE

graph TD
    A["LENS Mode"] --> B["DC"]
    A --> C["Indoor"]
    A --> D["Outdoor"]
    E["EXPOSURE"] --> F["SHUTTER"]
    E --> G["ACCE"]
    E --> H["AGC"]
    E --> I["DEFOG"]
    E --> J["SENS-UP"]
    E --> K["BRIGHTNESS"]
    E --> L["BACKLIGHT"]
    E --> M["RETURN"]
    N["WHITE BAL."] --> O["ATW"]
    N --> P["AWC->SET"]
    N --> Q["INDOOR"]
    N --> R["OUTDOOR"]
    N --> S["MANUAL"]
    T["DAY & NIGHT"] --> U["AUTO"]
    T --> V["COLOR"]
    T --> W["BW"]
    T --> X["EXT"]
    Y["NR"] --> Z["2DNR"]
    Y --> AA["3DNR"]
    Y --> AB["LEVEL (3D DNR)"]
    Y --> AC["SMART NR"]
    Y --> AD["RETURN"]
    AE["SPECIAL"] --> AF["CAM TITLE"]
    AE --> AG["D-F EFFECT"]
    AE --> AH["MOTION"]
    AE --> AI["PRIVACY"]

OSD MENU DETAILS

1) LENS

2) EXPOSURE

SHUTTER : Adjust shutter settings : Auto / A. FLK / Manual

- A. FLK mode reduces on-screen flickering.

- Electronic Shutter Control (AUTO) adjusts brightness level on screen.

- Manual mode allows you to adjust the shutter speed from 1/30 \~ 1/50,000 and also x2 \~ x30.

AGC (Auto Gain Control) : High / Middle / Low

- Controls Gain Noise to improve image quality.

- Set AGC Mode to High to increase the Gain.

SENS-UP : Off / Auto(x2 \~ x30)

- Automatically detects ambient light level and maintains a clear picture in low light conditions.

BRIGHTNESS : Adjust Brightness of the lens (1\~100 Steps)

ACCE : Off / Low / Middle / High

OSD MENU DETAILS

3) WHITE BAL.

ATW : Auto Tracking White Balance.

Use this mode when the color temp. is between 1,800\~10,000K

AWC->SET

- To find the optimal setting for current luminance environment in this mode. To manually set, point the camera towards a sheet of white paper and use the Joystick.

INDOOR : Loads indoor camera settings.

OUTDOOR : Loads outdoor camera settings.

MANUAL

- To fine-tune White Balance manually. Set White balance first by using ATW or AWC mode before Manual mode. After that, if there is still a white balance issue, switch to manual mode to fine-tune. Manual mode allows you to increase or decrease the red or blue factor.

4) DAY / NIGHT

AUTO : Automatic D/N switching according to ambient illumination.

Delay / D-N / N-D / Return Modes are provided.

COLOR : Sets the camera to display color video

OSD MENU DETAILS

6) SPECIAL

6-1) CAM TITLE : To program and display a camera title on the monitor.

6-2) D-EFFECT :

• Freeze : Freezes the display image.
• Mirror : Changes the video image via a vertical flip or mirror.
• D-Zoom : Digital Zoom In / Out up to 64x.

PIP : When D-Zoom is activated, the original picture will be shown in inset window.

PAN/TILT : Desired Pan /Tilt location of the PIP window

- Neg.Image : Image reversal ON/OFF

6-3) MOTION :

• A signal is generated by the camera whenever motion is detected. You can define 3 areas and control its sensitivity.

6-4) PRIVACY

To disable video in a selected area. 8 areas selectable.

6-6) LANGUAGE :

6-7) DEFECT :

Activate this setting when "White Spots or Dead Pixels" are detected.

• Live DPC : It corrects "Dead Pixel" while the camera is activated.
• Level : Set the desired level of Live DPC
• Static DPC : It corrects “Dead Pixel” when the camera is using Sens-Up.

SPECIFICATIONS

Item HDT471
Image Sensor 1/3" Progressive CMOS Sensor
Total Pixels 2010(H) x 1180(V) Approx. 2.22Megapixels
Effective Pixels 1944(H) x 1092(V) Approx. 2.12Megapixels
Video Output 1920(H) X 1080(V) 30P, 1280(H) X 720(V) 60P
Video Output Format	HD-SDI Output (1.5G/s, SMPTE 292M), Analog second video output, CVBS out simultaneously
Min. Illumination	0.1Lux (F.1.2, 50IRE, AGC Max.)0.01Lux (Sens-Up : Auto:x30)
S/N (Y signal) 52dB (AGC Off)
AGC LOW / MIDDLE / HIGH SELECTABLE
SHUTTER OFF / A.FLK / 1/30~1/50000 / X30 ~ X2 / AUTO
SENS-UP OFF / AUTO (X2~X30)
ACCE OFF / LOW / MIDDLE / HIGHT SELECTABLE
WHITE BALANCE ATW / AW C-SET / INDOOR / OUTDOOR / MANUAL
DAY / NIGHT AUTO / COLOR / BW / EXT SELECTABLE
NR(NOISE REDUTION)	2DNR / 3DNR / SMART NR SELECTABLE
MOTION DET.	ON | OFF (3 Programmable Zone)

DIMENSIONS

Unit : mm

* TOP VIEW

63

* SIDE VIEW

WARRANTY

LIMITED WARRANTY - VIDEO PRODUCTS

THIS WARRANTY IS VALID ONLY ON PRODUCTS PURCHASED AND USED IN THE UNITED STATES OF AMERICA AND CANADA. THIS WARRANTY APPLIES ONLY TO THE ORIGINAL USER.

SUBJECT TO CONDITIONS AND EXCLUSIONS FOUND BELOW, THIS PRODUCT IS WARRANTED AGAINST MANUFACTURING DEFECTS IN MATERIAL AND WORKMANSHIP FOR THE FOLLOWING PERIOD FOR PARTS AND LABOR:

SPECO TECHNOLOGIES CAMERAS....5 YEARS

SPECO TECHNOLOGIES IP CAMERAS....2 YEARS

SPECO PTZ AND VL CAMERAS....1 YEAR

SPECO TECHNOLOGIES MONITORS....1 YEAR

IR LEDS....90 DAYS

DVRS	3 YEARS
NVRS	3 YEARS
BALANCE OF
SPECO TECHNOLOGIES LINE	1 YEAR

SPECO TECHNOLOGIES WILL REPAIR OR REPLACE (A" OUR DISCRETION) ANY PARTS FOUND TO BE DEFECTIVE FOR THE WARRANTY PERIOD SPECIFIED. WE WILL PROVIDE A REPLACEMENT FOR ANY DEFECTIVE PART.

CONDITIONS

1. YOU MUST OBTAIN A RETURN AUTHORIZATION (RA) NUMBER FOR ANY MERCHANDISE BEING RETURNED TO SPECO TECHNOLOGIES, WHETHER FOR RETURN/EXCHANGE OR REPAIR, WHETHER IN OR OUT OF WARRANTY.

1. THIS WARRANTY WILL BE HONORED ONLY UPON PRESENTATION OF THE ORIGINAL DATED BILL OF SALE OR SALES SLIP

2. TRANSPORTATION OF THE PRODUCT TO OUR SERVICE DEPARTMENT IS THE RESPONSIBILITY OF THE USER, REPAIRED OR REPLACED PRODUCT WILL BE RETURNED PREPAID DURING THE WARRANTY PERIOD.

3. SPECO TECHNOLOGIES DOES NOT AUTHORIZE ANY INTERNET OR MAIL ORDER PRODUCT SALES. IF A SPECO TECHNOLOGIES PRODUCT IS PURCHASED FROM AN UNAUTHORIZED DISTRIBUTOR OR OTHER SOURCE, INCLUDING RETAILERS, MAIL ORDER SELLERS AND ONLINE SELLERS. IT WILL NOT BE HONORED OR SERVICED UNDER THE EXISTING SPECO TECHNOLOGIES WARRANTY POLICY. ANY SPECO TECHNOLOGIES PRODUCT PURCHASED FROM THESE ONLINE MERCHANTS WILL VOID THE APPLICABLE WARRANTY AND IS INELIGIBLE FOR TECHNICAL SUPPORT. IF YOU HAVE QUESTIONS ABOUT A RESELLER, PLEASE CONTACT SPECO TECHNOLOGIES AT 1-806-645-5516 FOR A LIST OF UNAUTHORIZED DEALERS, VISIT. WWW.specotech.com/unauthorized.

EXCLUSIONS

1. THIS WARRANTY SHALL NOT COVER ADJUSTMENT OF CUSTOMER OPERATED CONTROLS AS EXPLAINED IN THE APPROPRIATE MODEL'S INSTRUCTION MANUAL OR PRODUCTS WHICH HAVE BEEN ALTERED, ABUSED, OR HAVE MISSING OR ALTERED SERIAL NUMBERS.

2. THIS WARRANTY SHALL NOT APPLY TO UNCRATING, SETUP, INSTALLATION, OR THE REMOVAL AND REINSTALLATION OF PRODUCTS AFTER REPAIR

3. THIS WARRANTY SHALL NOT APPLY TO REPAIRS OR REPLACEMENTS NECESSITATED BY ANY CAUSE BEYOND THE RESULT OF MANUFACTURE INCLUDING, BUT NOT LIMITED TO ANY MALFUNCTION, EFFECTS OR FAILURE CAUSED BY OR RESULTING FROM UNAUTHORIZED SERVICE OR PARTS, IMPROPER MAINTENANCE, MODIFICATION OR REPAIR BY THE USER, ABUSE, MISUSE, NEGLECT, ACCIDENT, FIRE, FLOOD, OR OTHER ACTS OF NATURE, INCORRECT LINE VOLTAGE, DAMAGE OR IMAGE BURNS TO TELEVISION PICTURE TUBES CAUSED BY OR ATTRIBUTABLE TO THE USE OF ANY ACCESSORY, ELECTRONICS GAME OR DEVICE, OR DAMAGE CAUSED TO IMAGE PICKUP DEVICES BY EXCESSIVE LIGHT.

THE FORECOING IS IN LIEU OF ALL OTHER EXPRESSED WARRANTIES AND WE DO NOT AUTHORIZE ANY PARTY TO ASSUME FOR US ANY OTHER OR UNTATION OR LIABILITY IN THIS CLIENT SHALL WE ARE LIABLE FOR INCIDENTLY, OR QUOTOCENTUAL, MAJOR OR ANGIC FLOW.

spaco technologies®