T9503TEDT1 - Washing machine LG - Free user manual and instructions

USER MANUAL T9503TEDT1 LG

Washing Machine OWNER'S MANUAL

MODEL : T9503TEDT1 / T9503TEET1 T9503TEDT0

Please read this manual carefully before operating your set. Retain it for future reference.

Record model name and serial number of the set.

Quote this information to your dealer when you require service.

roduct Features

Washer doesn't operate while the lid is open. If the lid is open during the wash, rinse or spin cycles, the operation stops for safety.

1 sensors

- The sensor automatically detects the quantity of a Detergent put by a user and the temperature and the quality of water to make the best washing algorithm for washing and rinsing, which can give the best washing effect.

SMART CLEANING

- The purpose of this cycle is to optimize detergent residues during the washing and rising cycles, in order to implement this effect, the washer adds more rinsing times by I-sensor. Rinse can be added until max 5 times.

FUZZY logic control

- A built-in load sensor automatically detects the laundry load and a microprocessor optimizes washing conditions such as ideal WATER LEVEL and washing time.

● Advanced technology is built into the Electronic Control System which ensures the best washing result.

Turbo drum washing (option)

- When "Punch + 3" washing wings turn, the washing tub turns in the opposite direction. This makes the both sides current of water which improve wash-performance by rubbing clothes strongly.

3 Step washing

- 3 step washing makes the best washing performance with low tangling.

ontents

READ THIS MANUAL

Inside you will find many helpful hints on how to use and maintain your washer properly. Just a little preventive care on your part can save you a great deal of time and money over the life of your washer. You will find many answers to common problems in the Troubleshooting section. If you review our chart of Troubleshooting Tips first, you may not need to call for service at all.

Introduction	Safety Information	4
	Identification of Parts	7
	Function Information	8
Before Starting to Wash	Preparation Before Washing	9
	Use of Water, Detergent, and Softener	10
	Special Guide for Stain Removal	13
	Function of each Button	14
Washing Programs	FUZZY Wash (Normal Wash)	16
	WOOL Wash	16
	QUICK WASH	16
	JEANS Wash	16
	SMART CLEANING	16
	SOAK Wash	18
	FAVORITE Wash	19
	SILENT Wash	20
Additional Function Program	TUB CLEAN	21
	AIR DRY	22
	Option Washing	23
	DELAY START (RESERVATION) Wash	24
	Other Useful Functions	25
Installation	Placing and Leveling	26
	Connecting Water Supply Hose	27
	Connecting Drain Hose	30
Care and Maintenance	Grounding Method	31
	Cleaning and Maintenance	32

afety Information

Read carefully and thoroughly through this booklet as it contains important safety information that will protect the user from unexpected dangers and prevent potential damages to the product.

This booklet is divided into 2 parts: Warning and Caution.

: This is a warning sign specifying user's applications which might be dangerous.

: This is a sign specifying 'Strictly Forbidden' applications.

Warning : Failure to comply with the instructions under this sign may result in major physical injuries or death. Caution : Failure to comply with the Instructions under this sign may result in minor physical injuries or damages to the product.

WATER HEATER SAFETY	[BYTX] Warning
	• Under certain conditions hydrogen gas may be produced in a water heater that has not been used for two weeks or more. Hydrogen gas can be explosive under these circumstances.If the IOT water has not been used for two weeks or more, prevent the possibility of damage or injury by turning on all Hot water fucers and allowing them to run for several minutes. Do this before using any electrical appliance which is connected to the HOT water system. This simple procedure will allow any built-up hydrogen gas to escape. Since the gas is flammable, do not smoke or use an open flame or appliance during this process.
PROPER INSTALLATION	[SAWS] Caution
	• The base opening must not be obstructed by carpeting when the washing machine is installed on a carpeted floor.• Install or store where it will not be exposed to temperatures below freezing or exposed to the weather.If the product is exposed to such conditions, electric shock, fire, break down or deformation may occur.• Property ground washer to confirm with all governing codes and ordinances. Follow details in Installation Insections.If not grounded properly, break down and leakage of electricity may occur, which may cause electric shock.

Warning

Caution

afety Information

YOUR LAUNDRY AREA

Warning

• Keep the area underneath and around your appliances free of combustible materials such as lint, paper, rags, chemical, etc.
  Operating with such materials around the machine may trigger explosion or fire.
• Close supervision is necessary if this appliance is used by or near children. Do not allow children to play on, with, or inside this or any other appliance. There is potential danger that children might drown in the tub.

Do not touch the power plug with a wet hand. It will cause electric shock

Do not put your hand, foot or anything under the washing machine while the washing machine is in operation. There is a rotating mechanism under the machine, so you could be injured.

WHEN USING THE WASHER

Caution

• Use this appliance only for its intended purpose as described in this Owner's Manual.
• The laundry process can reduce the flame retardancy of fabrics. To avoid such a result, carefully follow the garment manufacturer's wash and care instructions.
• To minimize the possibility of electric shock, unplug this appliance from the power supply or disconnect the washer at the household distribution panel by removing the fuse or switching off the circuit breaker before attempting any maintenance or cleaning.

Pressing Power button to turn off does NOT disconnect the appliance from the power supply.

• Make sure that drainage is working properly. If water is not drained properly, your floor may get flooded. Flooded floors may induce electricity leakage, further resulting in electric shock or fire.
- If, during spinning, opening the lid does not stop the tab within about 15 seconds, immediately discontinue operating the machine.

Call for repair. A machine that spins with its door open may cause injuries.

Never reach into washer while it is moving.
Wait until the machine has completely stopped before opening the lid.
Even slow rotation can cause injury.

Never attempt to operate this appliance if it is damaged, malfunctioning, partially

afety Information

WHEN USING THE WASHER	[SHBA] Warning
	Do not use a pling socket and wiring equipment for more than their rated capacity. Exceeding the limit may lead to electric shock, fire, break down, and/or deformation of parts.
	Do not mix chlorine bleach with ammonia or acids such as vinegar and/or rust remover. Mixing different chemicals can produce toxic gases which may cause death.
	Do not wash or dry articles that have been cleaned in, washed in, soaked in, or spotted with combustible or explosive substances (such as wax, oil, paint, gasoline, dry- cleaning solvents, kerosene, etc). Do not add these substances in the wash water. Do not use or place these substances around your washer or dryer during operation. It may ignite or explode.
WHEN NOT IN USE	[TKSK] Caution
	• Tern off water faucets to relieve pressure on hoses and valves and to minimize leakage if a break or rupture should occur. Check the condition of the fill hoses: they may need replacement after 5years. • When the air temperature is high and the water temperature is low, condensation may occur and thus wet the floor. • Wipe off dirt or dust on the contacts of the power plug. Using unclean power plug may cause fire. • Before discarding a washer, or removing it from service, remove the washer lid to prevent children from hiding inside. Children may be trapped and suffocated if the lid is left intact. Do not attempt to repair or replace any part of this appliance unless specifically recommended in this Owner's Manual, or in published user-repair instructions that you understand and have the skills to carry out. Operating the machine with improperly replaced parts may be a cause for fire or electric shock. Do not temper with controls. It may lead to electric shock, fire, break down, deformation. Do not yank the power card in an attempt to disconnect the power plug. Securely hold the power plug to unpling the machine. Failure to observe these instructions may cause electric shock or fire due to short duration.

Warning

Caution

dentification of Parts

Body

POWDER AND LIQUID DELENGINE BOX (A5) LUNT FILTER Clean regularly to stop lining on the clothes lead. BENCH DISPENSER (6) FUNCTION SELECTORS TUB START/FAUSE BUTTON Use to start or stop the washing machine temporarily. ADJUSTABLE LIGS Use to level the washing machine for correct balance & spin operation. * WATER SUPPLY HODE Make sure the water does not look. POWER PLUG If the supply cord is damaged, it must be replaced by the manufacturer or for service against at similarly qualified person in order to avoid a hazard. * DRAN HOSE for pump model Check if the drain hose is hang up before operating the washing machine. * DRAN HOSE for non pump model. BASE

Accessories

Water supply hoses

1 Fach for COLD and

Drain hose Anti-rat cover (option)

Other washing method

[Non-Text]

[Non-Text]

[Non-Text]

Function Information

Our machine provides various washing methods which suits various conditions and types of laundry.

Different types of laundry washing

FUZZY(Normal) Wash

Use this Program for everyday washing e.g. sheets, towels, T-shirts. (refer to page 16)

.EANS Wash

Use this Program for heavily sealed durable garments e.g. overalls, jeans.

Thick and heavy clothes or these which are excessively dirty like years or working uniforms can be washed. (refer to page 16)

SMART CLEANING

Use this program to get better rising performance. (refer to page 10)

WOOL Wash

Wool clothes (lingerie, wool, etc.) which may be easily damaged can be washed. (refer to page 16)

The fibers of machine washable woolers have been specifically modified to prevent telling when they are machine washed.

Most handknated garments are not made of machine washable wool and we recommend that you hand wash them

- When washing wafens use a mild Detergent environmental for washing wool

- Hand washed coolers may be spun in a washing machine to reduce the time they take to cry.

- To dry woolens lay down them flat on a towel and put into shape. Dry woolens out of direct sunlight.

(The heat and turbine action in a dryer may cause shrinkage or melting in women' garments.)

Some wall undertays and sheepskin products can be washed in a washing machine but may cause pump messages.

You may wish to handwash these articles and place them in the machine to spin dry.

FAVORITE Wash

This setting allows you to store your FAVORITE wash conditions in the normal cycle memory. (refer to page 19)

SILENT Wash

Use this program to wash quietly at night. (refer to page 20)

Washing according to the condition of laundry

QUICK WASH

QUICK WASH can be selected to wash lightly soiled clothes of less than 2.0 kg in a short time. (refer to page 16)

SOAK Wash

SOAK Wash can be selected to wash heavily sealed laundry by soaking in water for some time to remove dirt and

grine. (refer to page 18)

TUB CLEAN

Use this program to clean the inside of washing machine especially Inner tub & Outer tub. (refer to page 21)

DELAY START Wash

reparation Before Washing

Care Labels

* Look for a care label on your clothes. This will tell you about the fabric content of your garment and how it should be washed.

Set clothes into loads that can be washed with the same wash cycle. Water Temperature and spin speed.

Sorting

To get the best results, different fabrics need to be washed in different ways.

• SOIL (Heavy, Normal, Light) Separate clothes according to the type and amount of soil.
• COLOR (Whites, Lights, Darks) Separate white fabrics from colored fabrics.
• LINT (Lint producers, Collectors) Separate lint producers and lint collectors.

Lint Producers - Terry cloth, Chenille, Towels, Nappies, Diapers

Lint Collectors Synthetics, Conlanary, Permanent Press, Sacks

Check before Loading

• Check all pockets to make sure that they are empty. Things such as nails, hairclips, matches,
  pens, curns, and keys can damage both your washer and your clothes.
• Mend any torn garments or loose buttons. Tears or holes may become larger during washing.
• Remove belts, underwires, etc. to prevent damage to the machine or your clothes.
  • Pretreat any dirt and stains
  • Make sure the clothes are washable in water.
• Check the washing instructions.
• Remove tissue in pockets.

Pretreatment on stains or heavy soil

• Pretreat shirt collars and cuffs with a pre-wash product or liquid Detergent when placing them in the washer.
  Before washing treat special stains with bar soaps, liquid Detergent or a paste of water and granular Detergent.
• Use a pretreat soil and storm remover
  Treat stairs AS SOON AS POSSIBLE. The longer they are left the harder they are to remove.
  (For more detail refer to page13)

Loading

Do not wash fabrics containing flammable materials (waves, cleaning fluids, etc.). Load Size

The WATER LEVEL should just cover the clothes. Adjust the load size accordingly. Loosely load clothes no higher than the top row of holes in the washer tab. To add items after washer has started, press Start button and submerge additional items. Close the lid and press Start button again to restart.

Light and Large-sized clothing

Clothes like down and available are light weight. Large and float easily. Use a nylon net and

WARNING

Fire Hazard

Never places items in the washer that are

dampered with gasoline or other tannable

1.13

No weather can completely remove oil

Do not try anything that has either all any type of oil or liquidation processing coal.

Doing so can result in death, explosion, or fire.

Use of Water, Dispenser Drawer, Detergent, and Softener

Using Water

Amount of WATER LEVEL

- This machine detects the quantity of laundry automatically, then sets the WATER LEVEL and proper amount of Detergent.

- When you select a wash program, the WATER LEVEL and amount of Detergent (to be used) will be shown on the control panel.

- The following table shows the amount of water. - When the WATER LEVEL is automatically detected, it may differ depending on the quantity of laundry even though the same WATER LEVEL is indicated on the control panel.

NOTE

[ Minimum water amount ]

It depends on laundry load and washer model. Or manually you can pour a certain amount water into tub directly to some height. That's because if water level reaches to the some height sensed by washer itself, washer automatically operates. In other words, it is needed to pour water to the point when washer starts operating.

Water Temperature

• The machine sets the appropriate temperature automatically according to the wash program

- You can change the Water Temperature by pressing the WATER TEMP. button. (refer to page 14)

- The temperature of the water impacts the effectiveness of all laundry additives and therefore, the cleaning results. We recommend temperatures of:

- HOT 49\~60°C...(120-140°F) White items, diapers, underclothing and heavily soiled, colorfast items.

- WARM 29\~40°C... (85-105°F) Most items - COLD* 18\~24°C... (65-75°F) Only very bright colors with light soil.

- When washing in COLD water additional steps may be needed:

- Adjust Detergent amount and pre-dissolve Detergent in WARM water

- Pretreat spots and stains

- Soak heavily soiled item

- Use appropriate bleach

* Temperature below 18°C...(65°F) will not activate laundry additives and may cause lint, residue, poor cleaning, etc. In addition, Detergent manufactures and care labels define COLD water as 26\~29°C...(80-85°F). If the temperature of the water in the tub is too cold for your hands, the Detergent will not activate and clean effectively.

NOTE

If iron is present in the water the clothes may become an all-over yellow or they may be stained with brown or orange spots or streaks. Iron is not always visible. Installation of water softener or an iron filter may be necessary for severe cases.

Using the Dispenser Drawer

The dispenser drawer contains 2 compartments:

• Liquid Fabric Softener

• Powder Low-Sulsing, High-Efficiency Detergent

The distance heterotrally distance additions at the mean time in the much mode

Using Detergent

Detergent

Follow the Detergent package directions. Using too little Detergent is a common cause of laundry problems. Use more Detergent if you have hard water, large loads, greasy or oily soils or lower Water Temperature.

Choosing the right Detergent

We recommend the use of domestic Detergent, (powder, liquid or concentrated). Soap flakes or granulated soap powders should not be used in your washing machine. When washing woolens remember to use Detergent suitable for washing woolens.

Using Detergent

How much Detergent

The correct amount of Detergent will vary depending on the amount of soil in your clothes (Jeans and work clothes may need more Detergent, while bath towels usually need less).

For liquid and concentrated Detergents, follow the recommendations of the Detergent manufacturer. Note: To check you are using the correct amount of Detergent, lift the lid of your machine about halfway through the wash. There should be a thin layer of foam over the surface of the water. Lots of foam may look good, but it does not contribute to cleaning your clothes. No foam means not enough Detergent has been used; soil and lint can settle back on the clothes or the washing machine.

If excess Detergent is used, the rinse will not be as clean and efficient. Also, it could cause environmental pollution, so use it accordingly.

Adding Detergent

Add measured detergent to the detergent compartment of the dispenser drawer.

For Liquid / Powdered Detergent

- Do not exceed the maximum fill line.

se of Water, Dispenser Drawer, Detergent, and Softener

Using Fabric Softener

If desired, pour the recommended amount of liquid fabric softener into the right-hand compartment.

Use only liquid fabric softener.

Dilute with water to the maximum fill line.

- Do not exceed the maximum fill line.

Overfilling can cause early dispensing of the fabric softener, which could stain clothes.

NOTE : Do not pour fabric softener directly on the wash load. It may stain the clothes.

Attention

■ Do not mix with Detergent or bleach.
■ Never pour fabric softener directly on clothes. It may stain them.
■ Do not stop the washer during the first spin for timely dispensing.
■ Option washing is not designed to be used with fabric softener dispenser.

Scrud(Waxy Build up)

Scrud is the name given to the waxy build-up that can occur within any washer when the fabric softener comes into contact with Detergent. This build-up is not brought about by a fault in the machine.
If scrud is allowed to build-up in the machine it can result in stains on your clothes or an unpleasant smell in your washer.

If you wish to use fabric softener we recommend

• Using fabric softener sparingly.
- When filling the dispenser, do not splash or overfill.
- Clean dispenser as soon as the cycle is finished.
• Clean your machine regularly. (refer to page 21 or 32)
- Cold water washing increases the chance of this build-up occurring. We recommend a regular WARM or HOT wash e.g. every 5th wash should be at least a warm one.
- Fabric softener of thinner consistency is less likely to leave residue on the dispenser and contribute to a build-up.

pecial Guide for Stain Removal

WARNING

■ Do not use or mix liquid chlorine bleach with other household chemicals such as toilet cleaners, rust removers, acid or products containing ammonia. These mixtures can produce dangerous fumes which can cause serious injury or death.
■ To reduce the risk of fire or serious injury to persons or property, comply with the basic warnings listed below:
- Read and comply with all instructions on stain removal products.
- Keep stain removal products in their original labeled containers and out of children's reach.
• Thoroughly wash any utensil used.
- Do not combine stain removal products, especially ammonia and chlorine bleach. Dangerous fumes may result.
- Never wash items which have been previously cleaned in, washed in, soaked in or spotted with gasoline, dry cleaning solvents
or other flammable or explosive substances because they give off vapor that could ignite or explode.
- Never use highly flammable solvents, such as gasoline, inside the home. Vapars can explode on contact with flames or sparks.

For successful stain removal:

• Remove stains promptly.
• Determine the kind of stain, then follow the recommended treatment in the stain
  removal chart below.
  • To pretreat stains, use a prewash product, liquid Detergent, or a paste made from
  granular Detergent and water.
• Use COLD water on unknown stains because HOT water can set stains.
• Check care label instructions for treatments to avoid on specific fabrics.
• Check for colorfastness by testing stain remover on an inside seam.
• Rinse and wash items after stain removal.

Follow fabric care label
instructions

Stain Removal
STAIN	TREATMENT
Adhesive size: dressing gum, cutter coat	Apply ice. Scrape off excess. Place stain face down or paper towels. Saturate with prewash stain remover or contaminated dry cleaning fluid.
Baby formax: dry product, egg	Use product containing enzymes to pretreat or soak stains.
Boreage (face, air soda juice, biotic texture)	Pretreat stain. Wash using COLD water and bleach safe for fabric.
Blood	Rins with COLD water. Rub with bar soup. Or pretreat or soak with product containing enzymes. Wash using bleach safe for fabric.
Code wax, copy	Scrape off surface wax. Place stain face down between paper towels. Press with warm iron tail wax is absorbed Replace paper towels frequently. Treat remaining stain with prewash stain remover or nonflammable dry cleaning fluid. Hold dust to remove soven. Wash using bleach safe for fabric.
Chassis	Pretreat or sink in WARM water using product containing enzymes. Wash using bleach safe for fabric.
Cell surface seal, osmatic	Pretreat or sink in WARM water using product containing enzymes. Wash using bleach safe for fabric.
Dry transfer or white fabric	Use packaged color remover. Wash using bleach safe for fabric.
Grams	Pretreat or sink in WARM water using product containing enzymes. Wash using bleach safe for fabric.
Grams oil for (water, ash, and drying cooking mix or grass, natural)	Scrape residue from fabric. Drycoat. Wash using bottled water safe for fabrics. For heavy stains and air, apply non-irradiative dry cleaning fluid to lock of stain. Freeze towels under stain frequently. Freeze thoroughly. Wash using hazardous water safe for fabric.
hk	Some links may be impresible to remove. Washing may set some ink. Use prewash stain remover, denatured alcohol or nonflammable dry cleaning fluid.
Mildew sores	Wash with chlorine bleach if safe for fabric. Or, soak in oxygen bleach and HOT water before washing. Badly mildewed flouries may be permanently damaged.
Mud	Brush off dry coat. Pretreat or soak with product containing enzymes.
Wood surface	Pretreat with prewash stain remover. Wash using bleach safe for fabric.

United States

unction of each Button

WATER TEMPERATURE BUTTON (Only 2 valve)

• Use to select Water
  Temperature.
  Pressing the Sumber allows
  you to select COLD WARM (HOT&GOLD)
  HOT ▲ COLD
  respectively
  Default setting is COLD.

WATER BUTTON

• Use to select the proper amount of water in relation to the weight and type of laundry.
  • Automatically controlled, but can be selected
  manually by pressing the WATER Bolton.
  • WATER is automatically selected for
  FUZZY(inormal) program
  The following settings are indicated as the button is
  planned
  7▶8•9▶10▶1▶2•3▶4▶5•6▶7

TIME LEFT, DELAY START (RESERVATION). ALARM INDICATION

• Time left - During operation, the remaining time is indicated
  • DELAY START INDICATION
  TRESERVATION) - When DELAY START
  [GR/SERVATION] program institutional, it
  indicates the following time. (K=5-391.51)
• Abitin indicated - when in order to be, in
  Message Speaks to above the Sociality. For example, dE indicates that the lid is open.

BEEPER BUTTON (Only 1 valve)

• If you want to use the
washing machine
without alarm signal
sounds, press BEEPER
buttons allow you to
select : HIGH ▶ OFF ▶
LOW • HIGH respectively
Default setting is HIGH.
(refer to page 25)

AIR DRY TEMP WATER WASH RINSE SPIN DELAY AIR DRY TEMP WATER WASH RINSE SPIN DELAY AIR DRY TEMP WATER WASH RINSE SPIN DELAY AIR DRY TEMP WATER WASH RINSE SPIN DELAY AIR DRY TEMP WATER WASH RINSE SPIN DELAY

AIR DRY

- This button is used for air-drying of your laundry.

- Air dry selections light up in sequence as follows.

TUB DRY ▶ 60 92 120

▶ TUB DRY as the button is pushed.

CHILD LOCK FUNCTION

- Use to lock or unlock the control buttons to prevent settings from

being changed by a child:

To lock, push the RINSE and

SPIN buttons simultaneously and

to unlock push them one more

time during the washing process.

(refer to page 25)

WASH. RINSE. SPIN BUTTON

- Use when wash, rinse, spin time need to be adjusted.

• The time increases when the

button is pressed

- IT adjustments are needed

during the wash, press the

[star/pause] button 5

making any changes.

- When the button is pressed

during washing, the remaining

NOTE

WASHING CONDITION INDICATOR (OPTION)

- It only operates in FUZZY Program.

- During being detected by the sensor, the LED flashes green, orange

and red in turn. And, after detecting, the LED lights a specific color according to the detecting condition as

follows:

If the current washing condition (Detergent quantity, Water Temperature, water quality, etc.) is determined as

better than the standard one, it optimizes the algorithm to save the energy by decreasing washing time/strength,

and the LED automatically turns to red.

* If the current washing condition is determined as worse than the standard one, it optimizes the algorithm by

Increasing washing time/strength, and the LED automatically turns to orange.

* If the current washing condition is determined as equal to the standard one, the algorithm has no change and the LED has no change.

LED turns to green.

POWER(AUTO OFF) BUTTON

• Use to turn the power in or off.

• Push again and power goes on or off

• The power goes off automatically about

10 seconds after the wash is finished

PROGRAM

POWER AUTO OFF

START PAUSE

DELAY START (RESERVATION) BUTTON

- Use to set a delayed finishing time.

- The time increases when the button is pushed.

• The following settings are indicated

as the button is pushed 3▶4▶5▶

• To cancel delay time, turn the power switch off.

(refer to page 24)

PROGRAM BUTTON

• Use for selecting wash program.

• This button allows you to select 8

different programs for different kinds of laundry and dirtiness.

• program selections light up in sequence as

follows: FUZZY(Normal) ▶ WOOL ▶

QUICK WASH ➕ ANS SMART

CLEANING ▶ SILFNT FAVORITE

▶ TUB CLEAN ▶U/Z/Y(Normal) etc.

Select the desired program by pressing the

button.

START/PAUSE BUTTON

• Use to start or pause the

washing process.

• Repeats start and pause by

pushing the button.

(五) 2017年1月1日

[Non-Text]

[Non-Text]

[Non-Text]

[Non-Text]

[Non-Text]

[Non-Text]

Washing Programs

Washing Programs		Add the laundry		Add the Detergent
Use this program for washing delicate fabrics such as lingerie and woolens. (wash only "water washable" clothes) Before washing your woolens check the care label for the washing instructions. (wash only water washable clothes)
Use this mode when washing lightly soiled clothes for a short time. The highly recommended laundry amount is under 2.0kg.
Use lean program when washing jeans of different sizes

	Close the lid Finish Caution & Note
The pulsator rotates for 8 seconds to detect the laundry load.Then the WATER LEVEL and the amount of Detergent to be used will be shown and water will be supplied.	Water will be supplied for 2 minutes after the start of the wash to supplement the water the laundry has absorbed.	When the wash program ends, the buzzer will ring for 10 seconds before the Power goes off automatically.	If water is already in the tub, or pulling wet laundry into the tub before starting will increase the WATER LEVEL.With lightweight bulky loads, WATER LEVEL can be set low.Changes to Water Temperature (HOT/COLD) and wash level are possible during operation.(refer to page 14)
			When setting the WATER LEVEL manually, do not set to Medium to prevent damage to laundry.Washing with HOT water may damage the laundry (Water is set to cold automatically). Ensure that the load is under 2kg.In order to avoid damage to laundry, the spin cycle may appear slow.This also avoids wrinkles and clothing may still contain some water. This is normal.
			When static pressure of water is more than 2kg/min, the QUICK WASH course will be within 15min.

OAK Wash

Use this mode to wash normal clothes or thick and heavy clothes which are excessively dirty. SOAK mode can be used with FUZZY or JEAN or SILENT or FAVORITE program.

1 Press the POWER (AUTO OFF) button to turn power on.

POWER AUTO OFF

2 Press the PROGRAM button to select the washing program.

PROGRAM

• SOAK will not work in WOOL and QUICK WASH, TUB CLEAN Program.

3 Press the WASH button, to select SOAK program.

WASH

- Keep pressing the WASH button until the light turns on 'SOAK' and 'WASIL' simultaneously as next image - SOAK program only works when socking time is 40, 50 or 60 minutes. Sensor

4 Add the Detergent. • The appropriate quantity of Detergent marked next to the

5 Add the laundry and press the START/PAUSE button.

START PAUGE

- The WATER LEVEL will be shown and water will be supplied.

6 Close the lid. • Water will be supplied for 2 minutes after the start of the

Finish

- When the wash program ends, the buzzer will ring for 10 seconds before the Power goes off automatically.

NOTE

• Order of Soak-Wash timing

Soak-Wasn

AVORITE Wash

Pressing the FAVORITE button allows you to store your FAVORITE wash conditions in the normal cycle memory and then recall it for use at a later time.

Press the POWER (AUTO OFF) button to turn power on.

POWER AUTO OFF

Select the FAVORITE program.

Select your FAVORITE wash conditions.

- Press the TEMP. button to select wash Water

Temperature.

- Press the WATER button to select

WATER

- Press the WASH button, the RINSE button & the SPIN

button to select wash time, rinse time & spin time

respectively you want to store.

Press the START/PAUSE button to store & start your FAVORITE wash cycle. Power turns off automatically after wash.

START PAUSE

19

Washing Programs

ILENT Wash

Use this program to wash quietly in SILENT especially during late night and dawn.

1 Press the POWER (AUTO OFF) button to turn power on.

POWER AUTO OFF

2 Press the PROGRAM button to select SILENT program.

PROGRAM

3 Add the laundry into the washing tub.

4 Press the START/PAUSE button.

START PAUSE

5 Add the Detergent and close the lid.

NOTE

• SILENT program takes longer washing time than FUZZY(Normal) program.
• To reduce noise in spinning, spin rpm is lower than normal spinning rpm. So the laundry has more moisture than normal.

TUB CLEAN

If scrud is allowed to build-up in the machine it can result in stains on your clothes or unpleasant smell in your washer.

Scrud is the way build-up that can occur within any washer when the fabric softener comes into contact with Detergent, and according to particular degree of dirtiness or quality of water to be use, in these case, use this program to clean inner tub and outer tub.

1 Press the POWER (AUTO OFF) button to turn power on.

POWER AUTO OFF

2 Press the PROGRAM button to select the TUB CLEAN program.

PROGRAM

※ Ex-Large WATER is set automatically.

3 Press the START/PAUSE button. • Left time is displayed.

START PAUSE

4 After 10 minutes of water supplement. Add the oxygenated bleach (about 300m).

- Do not use Detergent bus.

• Do not place any laundry inside tub.

5 Close the lid. When the lid is open the machine will not operate, and an alarm signal will remind you to close the lid.

NOTE

• Before using this program remove lint inside lint filter.
- When using this program, do not place any laundry inside tub.
• This program takes about 3 hours to be completed.
• After using this program, remove dirt inside filter.
• After finishing this program, open the lid of wash to remove irritant odor.

IR DRY

AIR DRY for your laundry.

Press the POWER (AUTO OFF) button to turn power on.

POWERWER AUTO OFF

Press the AIR DRY button to select-the desired timing.

AIR DRY

Press the START/PAUSE button.

START PAUSE

Closed the lid.

NOTE

■ Select "Air Dry" 30min → TUB DRY

-Use this mode to keep inner tub from getting moldy caused by remaining moisture.

- Do not place any laundry inside tub.

- Use this mode once a week.

(Caution) For better performance, put drain hose down to the floor so that water inside will be

completely drained out.

■ Select "Air Dry" above 1 hour

• Use this mode to reduce the drying time by minimizing remaining moisture on the laundry.
• In general, this is very effective on synthetic items(100% polyester)
• Do place laundry which is evenly distributed(Under 2kg).
• For normal clothes : Select 1 hour
• For synthetic items(100% polyester): Select 2 hours or 3 hours(on some models)

ption Washing

When you only need the Wash. Wash/Rinse or Rinse cycles, these can be set manually.

Press the POWER (AUTO OFF) button to turn power on.

Only Wash	Only Rinse	Only Spin
Press the WASH button to select the desired timing.WASH	Press the RINSE button to select the desired times of rinse.RINSE	Press the SPIN button to select the desired times of spin.SPIN
Only Wash,Rinse	Only Rinse,Spin	Only Drain
Press the WASH button to select the desired timing.WASHPress the RINSE button to select the desired times of rinse.RINSEYou can use this option for preventing wrinkles of laundry	Press the RINSE button to select the desired times of rinse.RINSEPress the SPIN button to select the desired times of spin.SPIN	When you want to only drain, wait until the water in the washing tub drains completely.

Press the WATER button, to control the water level according to the amount of laundry. If you do not choose anything, it is set the middle water level automatically.

Add the laundry into the washing tub.

Press the START/PAUSE button.

Add the detergent and place the lid

23

Additional Function Program

ELAY START (RESERVATION) Wash

DELAY START (RESERVATION) Wash is used to delay the finishing time of the operation.

The hours to be delayed can be set by the user accordingly.

The time on the display is the finishing time, not the start time.

Press the POWER (AUTO OFF) button to turn power on.

POWER AUTO OFF

Press the PROGRAM button to select the washing program.

PROGRAM

- Select the program for laundry on the Control panel.

This program will not work in WOOL and TUB CLEAN

Program.

Press the DELAY START (RESERVATION) button.

DELAY

The light will 'DELAY' turn on and

'TIME LEFT' 03:00 will be marked

Press the button repeatedly to set the desired finishing time.

For example, To finish washing in 9 hours from now, by

make the number 9:00 pressing the DELAY START

(RESERVATION) hutton repeatedly

(RES.=DELAY)

Add the Detergent.

- The appropriate quantity of Detergent marked next to the

WATER OF WATER•DETERGENT

- When the bid is open the machine will not operate, and an

alarm signal will remind you to close the lid

Add the laundry and press the START/PAUSE button.

STSTAR PAUSE

- When you press the START/PAUSE button the light will

blink

Close the lid.

- Water will be supplied for 2 minutes after the start of the

wash to supplement the water the laundry has absorbed.

Finish

• The washing will be finished according to the delayed time.

NOTE

- Finishing time can be delayed from 3–48 hours. Deloquent from 3–12 hours can be done in 1 hour time intervals:

ther Useful Functions

Child Lock Function

If you want to lock all the keys to prevent settings from being changed by a child, you can use the child lock option.

How to Lock

Press the POWER (AUTO OFF) button.

POWER AUTO OFF

• Turn Power on.

Press the START/PAUSE button to start washing.

START PAUSE

• After all washing conditions are set according to the manual.

Press both the RINSE button and the SPIN button simultaneously.

- During the wash program, all the buttons are locked until washing is completed or it is child-lock function is deactivated manually.

How to Unlock

If you want to unlock during wash, press both the RINSE and the SPIN button simultaneously again.

NOTE

• [L] & the remaining time are alternatively shown on the display while they are locked.

Beeper Option (For only 1 valve)

If you want to use the washing machine without alarm signal sounds, press BEEPER buttons allow you to select: HIGH ▶ OFF ▶ LOW ▶ HIGH respectively. Default setting is HIGH. To make buzzer work, press both the BEEPER buttons simultaneously one more time.

25

Additional Function Program

lacing and Leveling

Please ensure that transit restraint has been removed before operating your machine

Place the machine on a flat and firm surface which allows proper clearance.

We suggest a minimum clearance of 2 cm to the

right side and left sides of the machine for ease of installation.

At the rear, a minimum clearance of 10 cm is suggested.

NOTE

If the washer is installed on a uneven,weak or tilted floor causing excessive vibration,

spin failure or "UE" error can happen to it.

It must be placed on a firm and level floor to prevent spin failure.

Check that the machine is level

Open the lid and look from above to see if it is same as shown.

Top view of the machine

Leveling the machine

Lift the front of the washing machine and twist the Adjustable Leg until the surface bubble is placed in the center.

Adjustable legs

* Installing the Anti-Rat Cover (option) Insert the anti-rat cover to be firmly fixed from the back or front of washing machine and screw it

onnecting Water Supply Hose

Before connecting the Water Supply Hose to the water tap, check the hose type and then choose the correct instruction here under.

Note that the Water Supply Hose supplied may vary from country to country. Make sure to connect the blue inlet hose to the COLD water tap, and the orange inlet hose to the HOT water tap.

Connecting Water Supply Hose to water tap

Normal Type

(Normal tap without thread & screw type inlet hose.)

Untighten the screw

Unlighten the screw of the connector so that the tap can be placed in the middle.

Fixing the connector to the tap

Push the upper connector up till the rubber packing is in tight contact with the tap. Then tighten the 4 screws.

Attach the water supply hose securely to the connector

Push the water supply hose vertically upwards so that the rubber seal within the hose can adhere completely to the tap.

Fixing the connector to the water supply hose

Attach the water supply hose to the connector and then tighten it by screwing it to the right.

Check the connection of water supply hose and the connector

After connecting the hose, open the tap to check for any water leakage.

onnecting Water Supply Hose

Normal Type (Normal tap without thread & one touch type inlet hose.)

Separate Middle connector from Water Supply Hose

Separate Middle connector from the Water Supply Hose by pulling the Pressing Rod and the Pressing Handle that is attached to the Water Supply Hose.

Middle connector

Fixed Sticker Pressing Handle

Pressing Rod

Fressing Rod

Water Supply Hose

2 Loosen the fixed nuts to connect the connector to the tap

Untighten the screw of the connector so that the tap can be placed in the middle.

Rubber packing screw

Fixed sticker

NOTE

In case tap is too large. If the tap diameter is too large or is square, untighten the 4 screws and remove the guide plate. Then follow stept.

3 Fixing Connectors to the Tap

Push the upper connector up till the rubber packing is in tight contact with the tap. Then tighten the 4 screws.

4 Fixing Upper Connector and Middle Connector

Remove the fixed sticker in between the Upper and Middle Connectors. Tighten the connectors by holding one connector and twist middle connector to the right.

5 Connecting Middle Connector and Water Supply Hose

Press down the pressing rod of the Water Supply Hose which was separated from middle connector (refer to Step1) and then join it to the middle connector.

Water Supply Hose

Screw Type

1 Attach the water supply hose to the tap.

Push the water supply hose up so that the rubber packing within the hose can adhere completely to the tap.

2 Connect the water supply hose to the tap.

Connect the water supply hose to the tap and then tighten it by screwing it to the right.

3 Check water leakage.

After connecting the hose, open the tap to check for any water leakage.

Connecting Water Supply Hose to the machine

- Connect the water supply hose to inlet valve of the washing machine, and then lock it by turning the hose connecting part.

- Check to see if there is a rubber seal inside the connector.

onnecting Drain Hose

Before connecting Drain Hose, check your Drain Hose model and choose the correct instructions.

Pump Model

1 Fit the end of the drain hose to the outlet of the drain pump and tighten the clamp.

2 Put the other end of the drain hose over the standpipe or wash tub.

Hose Guide Within 50mm 0.9-1.2m Drain Hose

NOTE

* To prevent siphoning, the drain hose should not extend more than 50 mm from the end of the hose guide.
* The discharge height should be approximately 0.9 - 1.2 m from the floor.

Non-Pump Model

1 Before connecting

Ensure that the hose clip is set as indicated here.

2 Connect the Elbow Hose

Push the elbow hose toward the body of the washing machine.

rounding Method

Earth wire should be connected.

If the earth wire is not connected, there is possible a danger of electric shock caused by the current leakage.

Grounding Method with Ground insert space Terminal

If the AC current outlet has a ground terminal, then separate grounding is not required. Note that AC power outlet configurations may differ from country to country

Ground Terminal

Outlet with ground terminal.

Caution

CAUTION concerning the Power Cord

Most appliances recommend they be placed upon a dedicated circuit; that is, a single outlet circuit which powers only that appliance and has no additional outlets or branch circuits. Check the specification page of this owner's manual to be certain. Do not overhead wall outlets. Overloaded wall outlets, loose or damaged wall outlets, extension curbs, forced power curbs, or damaged or cracked wire insulation are dangerous. Any of these conditions could result in electric shock or fire. Periodically examine the cord of your appliance, and if its appearance indicates damage or deterioration, unplug it, discontinue use of the appliance, and have the cord replaced with an exact replacement part by an authorized server. Protect the power cord from physical or mechanical abuse, such as being twisted, knitted, pinched, closed in a door, or walked upon. Pay particular attention to plugs, wall outlets, and the point where the cord exists the appliance.

Other Grounding Method

Burying Copper Plate

Connect the Ground Wire to a Ground Copper Plate and bury it more than 75cm in the ground.

Using Ground Wire

Connect the ground Wire to the socket provided exclusively for Grounding.

Using a Short Circuit Breaker

If grounding methods described above are not possible, a separate circuit breaker should be employed and installed by a qualified electricity

leaning and Maintenance

Cold water washing

- If you always use COLD water, we recommend that a WARM or HOT wash be used at a regular intervals e.g. every 5th wash should be at least a WARM one.

When you have finished

• Turn off taps to prevent the chance of flooding should a hose burst.
  • Always unplug the power cord after use.

When water supply into the tub is not clean or the filter is clogged with particles (such as sand), clean the filter in the inlet valve occasionally.

(The figure of power cord and water tap may vary according to the country)

To Clean the Filter in the Inlet Valve

1 Close the tap before turning off the power. Select both IIOT/COLD and then press the [START/PAUSE] button to remove water from the machine completely.

3 After removing the water supply hose pull out the filter. Then use a brush to clean the filter

Turn off the power before pulling out the cord.

Replace the filter after cleaning it.

NOTE

• Before cleaning the filter, the impurities in the water supply hose should be removed.

To Clean the Lint Filter

1 2 3 4 5

NOTE

- If the first filter is torn or damaged, purchase a new one from 1.G service center.

To Clean the Pump casing (for pump model)

1. T. 10: A towel on the floor under the drain pump cap. Excess water may flow out.

Remove any foreign objects and fluff inside pump casing and from the filter.

Replace the cap, insert the filter along the guide ribs inside the pump casing. Filter must face the guide ribs inside pump casing and securely turn the cap clockwise. Guide rib

leaning and Maintenance

When there is a fear of freezing

• Close the water taps and remove the Water Supply Hose.
• Remove the water which remains in the water supply.
• Lower the drain hose and drain the water in the bowl and the drain hose by spinning.

If frozen

• Remove the water supply base, and immerse it in HOT water at approx., 40°C.
• Pour approx.. 2 liters of HOT water at approx.. 40^ , into the bowl and let it stand for 10 minutes.
• Connect the water supply hose to the water tap and confirm that the washing machine performs the supply and drainage of water.

Wash Inner-tub

Leave the lid open after washing to allow moisture to evaporate. If you want to clean the inner-tub use a clean soft cloth campened with liquid Detergent, then rinses. (Do not use harsh or gritty cleaners.)

Inlet Hoses

Hoses connecting washer to faucet should be replaced every 5 years.

Exterior

Immediately wipe off any spills. Wipe with damp cloth. Try not to hit surface with sharp objects.

Long Vacations

Be sure water supply is shut off at faucets. Drain all water from hoses if weather will be below freezing.

Cleaning the Inside of your Washer

If you use fabric softener or do regular COLD water washing, it is very important that you occasionally clean the inside of your washer.

• I'll your washer with HOT water.
- Add about two cups of a powdered Detergent that contains phosphate.
• Let it operate for several minutes.
- Stop the washer, open the lid and leave it to soak overnight.
• After soaking, drain the washer and run it through a normal cycle.
Or use TLH CLEAN PROGRAM periodically.
We do not recommend that you wash clothes during this procedure.

Products that might damage your washing machine

• Concentrated bleaches and diaper sanitizer will cause damage to the paintwork and components of your washer.
• Hydrocarbon solvents i.e. petrol, paint thinners and lacquer thinners, etc. can dissolve plastic and blister paint (Be careful when washing garments stained with these solvents as they are flammable DO NOT put them in washer or dryer.)

ommon washing problems

Many washing problems involve poor soil & stain removal, residues of lint and scum, and fabric damage. For satisfactory washing results, follow these instructions.

WASH PROBLEM

Problems	Possible Causes	Solutions & Preventive Measures
Poor soil removal	· Not enough Detergent · Wash Water Temperature too low. · Overloading the washer · Incorrect wash cycle · Incorrect sorting · Do not pretreat stain	· Use correct amount of Detergent for load size, amount of soil and water Hardness. · Use WARM or HOT water for normal soil. Difficult. Water Temperature may be required according to soil type (refer to page 10). · Reduce load size. · Wash with JEAN or SOAK & JEAN wash cycle for heavy soiled laundry. · Separate heavily soiled items from lightly soiled ones. · Pretreat stain and heavy soil according to directions shown on page 9.
Blue Stains	· Undiluted fabric softener dispensed directly onto fabric	· Rub the stain with bar soup. Wash. · Do not overfill fabric softener dispenser and do not pour liquid fabric softener directly onto fabric. See page 12 for more instructions.
Black or gray marks on clothes	· A buildup caused by the interaction of fabric softener and Detergent can flake off and mark clothes · Not enough Detergent	· Keep the recommendations against. Scrull wavy buildup). (refer to scrd page 12.) · So correct amount of Detergent for load size, amount of soil and water Hardness.
Yellow or brown rust stains	· Iron or manganese in water supply, water pipes, or water heater	· To normalize discolored lead of white, use red remover sale for fabric. · Install nonprecipitating water softener or an iron filter in your water supply system for an ongoing problem. · Before washing, run water for a few minutes to clear lacks.
Lint	· Incorrect sorting · Tissues left in pocket · Overloading the washer	· Wash lint givers og towels, dynamette sheets, separately from lint collectors og synthetic fabrics and remove tissues in pockets before wash. See page 9 for sorting and caring before loading. · Do not overload the washer.
Residue or Detergent	· Overloading the washer · Undissolved Detergent · Use too much Detergent	· Do not overload the washer. · Some Detergents used to be pre-dissolved, clock the Detergent instructions. Try pre-dissolving the Detergent. · Increase Waste Temperature using HOT water safe for fabric. · Use proper amount of Detergent.

11.12.10

roubleshooting

Before calling for service, check the problem against the list bellows.

Symptom Error Message		Check up
Water Supply Failure		• Is the water tap shot off?• Is the water supply cut off?• Is the tap or water supply hose frozen?• Is the water pressure low or is the filter of the inlet valve clogged with impurities?• Is the Hot hose connected to cold?• Is the Cold hose connected to hot?
Drainage Failure		• Is the drain hose positioned correctly?• Is the drain hose bent or placed too high?• Is the internal part of the hose or drain pump (only pump model) clogged with impurities?• Check if electric power has gone off.
Spin Failure		• Is the laundry evenly balanced?• Is the washing machine placed on a flat surface?
Door(Lid) Open		• Is the lid closed?
Internal sensing failure		• Please call your nearest LG Electronics service center for help.

Terms of Warranty

What Is Not Covered:

• Service trips to your home to teach you how to use the product.
- If the product is connected to any voltage other than that shown on the rating plate.
- If the fault is caused by accident, neglect, misuse or Act of God.
- If the fault is caused by factors other than normal domestic use or use in
accordance with the owner's manual.
- Provide instruction on use of product or change the set-up of the product.
- If the fault is caused by pests for example, rats or cockroaches etc..
- Noise or vibration that is considered normal for example water drain sound, spin sound, or warming beeps.
- Correcting the installation for example, levelling the product, adjustment of drain.
• Normal maintenance which recommended by the owner's manual.
- Removal of foreign objects / substances from the machine, including the pump and inlet hose filter for example, grit, nails, bra wires, buttons etc.
- Replace fuses in or correct house wiring or correct house plumbing.
- Correction of unauthorized repairs.
- Incidental or consequential damage to personal property caused by possible defects with this appliance.
- If this product is used for commercial purpose, it is not warranted.
(Example : Public places such as public bathroom, lodging house, training center, dormitory)

If the product is installed outside the normal service area, any cost of transportation involved in the repair of the product, or the replacement of a defective part, shall be borne by the owner.

pecification

Illustration of a single water heater with labeled dimensions (W, D, H) and control panel (no text or symbols on the device itself)

37

Specification

Mndel

T9503TEDT1/T9503TRETI/T9503TEDTO

Power supply

220-240V\~50Hz

Weight

42 kg

Size

611(W) × 635(D) × 992(H)

Water tab pressure

30 - 800 kPa (0.3 - 8.0 kgf/cm²)

emo

Memo

المواصفات

Illustration of a portable kitchen appliance with labeled dimensions (no text or symbols on the device itself)

T9503TEDT1 / T9503TEET1 / T9503TEDT0

611(W) x 635(D) x 992(H)

30 - 800 kPa (0.3 - 8.0 kg/cm²)

الموديلات

tightةima.

Illustration showing five sequential steps of a food or food preparation procedure, labeled 1 to 7.

rr

العربية

m = 311

[Non-Text]

[Non-Text]

[Non-Text]

[Non-Text]

[Non-Text]

الغسيل الافتياري

• ت Connectivity Learning Strategy: Shows Simple, incline, administrative, clinical, and clinical

m = 311

m = 311

m = 311

m = 311

m = 311

m = 311

m = 311

m = 311

2

1

R

m = 311

m = 311

m = 311

m = 311

m = 311

m = 311

m = 311

1

[Non-Text]

[Non-Text]

[Non-Text]

[Non-Text]

[Non-Text]

[Non-Text]

[Non-Text]

[Non-Text]

[Non-Text]

[Non-Text]

[Non-Text]

[Non-Text]

[Non-Text]

[Non-Text]

[Non-Text]

[Non-Text]

[Non-Text]

[Non-Text]

[Non-Text]

[Non-Text]

[Non-Text]

[Non-Text]

[Non-Text]

[Non-Text]

[Non-Text]

[Non-Text]

[Non-Text]

[Non-Text]

[Non-Text]

[Non-Text]

[Non-Text]

[Non-Text]

[Non-Text]

[Non-Text]

[Non-Text]

[Non-Text]

[Non-Text]

تعريف الأجنبية