CD1561.07FKO - Switch JUNG - Free user manual and instructions

USER MANUAL CD1561.07FKO JUNG

Light Management Radio-control pushbutton and pilot lamp

Ref.-no.:

Operating Instructions Radio-control pushbutton and pilot lamp

1. Function

The radio-contol pushbutton permits radio-controlled or manual switching and dimming of lamps. The starting brightness can be stored in the device as memory brightness. The pushbutton with radio-control receiver is plugged onto one of the following inserts:

■ Universal touch dimmer 1254 UDE
- Standard touch dimmer 1225 SDE
- Relay insert single-channel 1201 URE
- Relay insert two-channel 1202 URE
- Tronic switching insert 1254 TSE
- LV triac switching insert 1244 NVSE
■ Touch control unit 1240 STE

JUNG

Light Management Radio-control pushbutton and pilot lamp

Ref.-no.:

Important

The present instructions describe the functions of the radio-control pushbutton without lighting control. More information on light control with a presence detector is set out in the operating instructions for these devices.

WARNING!

Caution: The installation and assembly of electrical equipment may only be performed by a skilled electrician.

2. Fitting

The radio-control pushbutton can only be operated in conjunction with the inserts listed under 'Functions'. Connection and fitting are described in the operating instructions of the insert.

Procedure

1. Install the selected insert (1) in a flush-mounting box (deep model recommended), the connecting terminals of the insert pointing downwards.
2. Plug the radio-control pushbutton (2) together with frame (3) onto the insert while the mains voltage is disconnected.

JUNG

Light Management Radio-control pushbutton and pilot lamp

Ref.-no.:

> 4 s Prog 1 min t

1. Send a radio telegram from the selected transmitter (fig. D); see "Radio-control transmitter" operating instructions:
   

Programming a channel

Depress the channel key for more than 1 second.

Programming a lightscape key

Depress the lightscape key for more than 3 seconds.

Programming a detector

Remove the battery for about 2 minutes from the detector. Put the battery back in place and make a movement inside the detection range of the detector within the next 10 minutes.

Programming a presence detector

JUNG

Light Management Radio-control pushbutton and pilot lamp

Ref.-no.:

① The programming of a radio channel (e.g. hand-held transmitter 'Komfort') always includes the simultaneous and automatic storage of the functions of the All-ON or All-OFF key.

Deleting a radio-control transmitter

A radio-control-transmitter in the pushbutton's memory is deleted when the same transmitter is programmed again into the memory (see above). All channels and lightscape keys must be deleted one by one. Successful deletion is indicated by the LED blinking fast (fig. F).

Deleting all radio-control transmitters

It is possible to delete all transmitters in the radio pushbutton. In this case, the radio pushbutton is reset to the state as delivered.

1. Depress both faces of the radio pushbutton at the same time for about. 20 s (Fig.. G: full-faced operation). After abt. 4 s, the LED starts blinking (cf. Fig. C). After 20 s the LED emits brief flashes of light for abt. 6 s.

JUNG

Light Management Radio-control pushbutton and pilot lamp

Ref.-no.:

Illustration of a hand pointing at a light bulb with a lightbulb above it (no text or symbols)

Short depression of pushbutton (< 0,4 s)

The lights are switched on (on with memory brightness) or off. When the lights are on, the LED is illuminated.

Short depression of pushbutton (> or = 0,4 s)

When the radio-control pushbutton is attached to an insert permitting the dimming function, the brightness of the lamps connected can be increased (upper rocker) and decreased (lower rocker) by a long depression of the pushbutton rockers.

① To switch on the lamps at minimum brightness, depress the lower rocker for more than 0.4 seconds when the lamps are off.

3.1. Memory-function

The selected brightness level can be stored as memory value in the radio-control pushbutton. A brief depression of the pushbutton recalls the memory brightness level as the starting brightness of the lamp.

Storing the memory value

Light Management Radio-control pushbutton and pilot lamp

Ref.-no.:

4. Radio Transmission

Radio transmission takes place on a non-exclusive path. Therefore, interference cannot be excluded. This type of radio transmission is not suitable for safety applications such as emergency stops or emergency calls. The range of a radio-control system depends on transmitter power, receiver characteristics, air humidity, fitting height and building conditions. Fig. 1 illustrates the penetration of building materials by radio waves:

Illustration of a hand interacting with a wall-mounted control panel, next to a circuit board, a switch, and a lightbulb (no text or symbols present)

Dry

material

Permeability

Timber, gypsum, gypsum-plasterboards approx. 90 %

Brickwork, particle boards

approx.

70

%

Reinforced concrete approx. 30 %

Metal, metal grating, aluminium lamination approx. 10%

Rain, snow

approx.

0

40

Radio operation

Light Management Radio-control pushbutton and pilot lamp

Ref.-no.:

6. Guarantee

Our products are under guarantee within the scope of the statutory provisions.

Please return the unit postage paid to our central service department giving a brief description of the fault:

ALBRECHT JUNG GMBH & CO. KG

Service-Center

Kupferstr. 17-19

D-44532 Lünen

Service-Line: +(49) 23 55 . 80 65 51

Telefax: +(49) 23 55 . 80 61 65

The C€-Sign is a free trade sign addressed exclusively to the authorities and does not include any warranty of any properties.