Focus Profile - Machine à effets American DJ - Free user manual and instructions

USER MANUAL Focus Profile American DJ

Black triangular light fixture with yellow lens and control panel (no visible text or symbols)

User Manual

©2021 ADJ Products, LLC all rights reserved. Information, specifications, diagrams, images, and instructions herein are subject to change without notice. ADJ Products, LLC logo and identifying product names and numbers herein are trademarks of ADJ Products, LLC. Copyright protection claimed includes all forms and matters of copyrightable materials and information now allowed by statutory or judicial law or hereinafter granted. Product names used in this document may be trademarks or registered trademarks of their respective companies and are hereby acknowledged. All non-ADJ Products, LLC brands and product names are trademarks or registered trademarks of their respective companies.

ADJ Products, LLC and all affiliated companies hereby disclaim any and all liabilities for property, equipment, building, and electrical damages, injuries to any persons, and direct or indirect economic loss associated with the use or reliance of any information contained within this document, and/or as a result of the improper, unsafe, insufficient and negligent assembly, installation, rigging, and operation of this product.

DOCUMENT VERSION

Due to additional product features and/or enhancements, an updated version of this document may be available online.

Please check www.adj.com for the latest revision/update of this manual before beginning installation and/or programming.

Date	Document Version	Software Version	DMX Channels Notes
09/21/2021	1.0 1.2.1 36 /	40 / 51 channels	Initial Release

Europe Energy Saving Notice

Energy Saving Matters (EuP 2009/125/EC)

Saving electric energy is a key to help protecting the environment. Please turn off all electrical products when they are not in use. To avoid power consumption in idle mode, disconnect all electrical equipment from power when not in use. Thank you!

TABLE OF CONTENTS

General Information 4
Key Features | Warranty Returns 5
Limited Warranty (USA Only) 6
Safety Guidelines 7
Overview 8
DMX Set Up 9
Installation 11
Gobo Replacement 15
Control Panel 20
System Menu 21
DMX Addressing 25
DMX Traits 26
White Color Temperature Presets 36
Color Wheel 37
Dimmer Modes and Curves	38
Frame Macros Table	39
Cleaning and Maintenance	40
Fuse Replacement | Software Updates	41
Dimensional Drawings	42
Specifications	43
Error Codes	44

GENERAL INFORMATION

Introduction: Congratulations on your purchase of the ADJ Focus Profile! This device is a 400W, CMY (Cyan, Magenta, Yellow), LED moving head spot, and has been designed to perform reliably for years when the guidelines in this booklet are followed. Please read and understand the instructions in this manual carefully and thoroughly before attempting to operate this device. These instructions contain important information regarding safety during use and maintenance.

Please keep this manual with the device for future reference.

Customer Support: Contact ADJ Service for any product related service and support needs. Also visit forums.adj.com with questions, comments or suggestions.

Parts: To purchase parts online visit:

http://parts.adj.com (US)

http://www.adjparts.eu (EU)

ADJ SERVICE USA - Monday - Friday 8:00am to 4:30pm PST

Voice: 800-322-6337 | Fax: [phone] | [e-mail]

ADJ SERVICE EUROPE - Monday - Friday 08:30 to 17:00 CET

Voice: [phone] | Fax: [phone] | [e-mail]

ADJ PRODUCTS LLC USA

6122 S. Eastern Ave. Los Angeles, CA. 90040

323-582-2650 | Fax [phone] | www.adj.com | [e-mail]

ADJ SUPPLY Europe B.V

Junostraat 2 6468 EW Kerkrade, The Netherlands

[phone] | Fax [phone]

www.adj.eu | [e-mail]

ADJ PRODUCTS GROUP Mexico

AV Santa Ana 30 Parque Industrial Lerma, Lerma, Mexico 52000

[phone]

WARNING! To prevent or reduce the risk of electrical shock or fire, do not expose this unit to rain or moisture.

CAUTION! There are no user serviceable parts inside this unit. Do not attempt any repairs yourself, as doing so will void your manufacturer's warranty. In the unlikely event your unit may require service, please contact ADJ Products, LLC.

Do not discard the shipping cartoon in the trash. Please recycle when ever possible.

KEY FEATURES

• 400W LED engine
  • 20,000 total lumens (fully zoomed out)
  • 7 to 45 degree zoom range
  • 6,700K color temperature
  • >70 CRI
  • 4 rotating framing shutter blades
  • Full CMY color mixing
  • 0-100% variable CTO

INCLUDED ITEMS:

• Twist-lock power cable (x1)
• Omega brackets (x2)

WARRANTY RETURNS

All returned service items, whether under warranty or not, must be freight pre-paid and accompanied by a return authorization (R.A.) number. The R.A. number must be clearly written on the outside of the return package. A brief description of the problem as well as the R.A. number must also be written down on a piece of paper included in the shipping carton. If the unit is under warranty, you must provide a copy of your proof of purchase invoice. You may obtain an R.A. number by contacting our customer support team. All packages returned to the service department not displaying an R.A. number on the outside of the package will be returned to the shipper.

LIMITED WARRANTY (USA ONLY)

A. ADJ Products, LLC hereby warrants, to the original purchaser, ADJ Products, LLC products to be free of manufacturing defects in material and workmanship for a prescribed period from the date of purchase (see specific warranty period on reverse). This warranty shall be valid only if the product is purchased within the United States of America, including possessions and territories. It is the owner's responsibility to establish the date and place of purchase by acceptable evidence, at the time service is sought.
B. For warranty service, you must obtain a Return Authorization number (RA#) before sending the product back—please contact ADJ Products, LLC Service Department at 800-322-6337. Send the product only to the ADJ Products, LLC factory. All shipping charges must be prepaid. If the requested repairs or service (including parts replacement) are within the terms of this warranty, ADJ Products, LLC will pay return shipping charges only to a designated point within the United States. If the entire instrument is sent, it must be shipped in its original package and packaging material. No accessories should be shipped with the product. If any accessories are shipped with the product, ADJ Products, LLC shall incur no liability whatsoever for loss of or damage to any such accessories, nor for the safe return thereof.
C. This warranty is void if the product serial number and/or labels are altered or removed; if the product is modified in any manner which ADJ Products, LLC concludes, after inspection, affects the reliability of the product; if the product has been repaired or serviced by anyone other than the ADJ Products, LLC factory unless prior written authorization was issued to purchaser by ADJ Products, LLC; if the product is damaged because it was not properly maintained as set forth in the product instructions, guidelines and/or user manual.
D. This is not a service contract, and this warranty does not include maintenance, cleaning, or periodic checkup. During the period specified above, ADJ Products, LLC will replace defective parts at its expense with new or refurbished parts, and will absorb all expenses for warranty service and repair labor by reason of defects in material or workmanship. The sole responsibility of ADJ Products, LLC under this warranty shall be limited to the repair of the product, or replacement thereof, including parts, at the sole discretion of ADJ Products, LLC. All products covered by this warranty were manufactured after August 15, 2012, and bear identifying marks to that effect.
E. ADJ Products, LLC reserves the right to make changes in design and/or improvements upon its products without any obligation to include these changes in any products theretofore manufactured.
F. No warranty, whether expressed or implied, is given or made with respect to any accessory supplied with products described above. Except to the extent prohibited by applicable law, all implied warranties made by ADJ Products, LLC in connection with this product, including warranties of merchantability or fitness, are limited in duration to the warranty period set forth above. And all warranties, whether expressed or implied, including warranties of merchantability or fitness, are limited in duration to the warranty period set forth above. The consumer's and/or dealer's sole remedy shall be such repair or replacement as is expressly provided above; and under no circumstances shall ADJ Product, LLC be liable for any loss and/or damage, direct and/or consequential arising out of the use of, and/or inability to use this product.
G. This warranty is the only written warranty applicable to ADJ Products, LLC products, and supersedes all prior warranties and written descriptions of warranty terms and conditions heretofore published.

MANUFACTURER'S LIMITED WARRANTY PERIODS:

• Non-LED Lighting Products = 1-Year (365 Days) (Including Special Effect Lighting, Intelligent Lighting, UV lighting, Strobes, Fog Machines, Bubble Machines, Mirror Balls, Par Cans, Trussing, Lighting Stands, Power/Data Distribution, etc. excluding LED and lamps)
  • Laser Products = 1-Year (365 Days) (excluding laser diodes which have a 6-Month Limited Warranty)
• LED Products = 2-Year (730 Days) (excluding batteries which have a 180 Day Limited Warranty)
  NOTE: 2-Year (730 Days) Limited Warranty ONLY applies to product purchased within the United States. StarTec Series = 1-Year (365 Days) (excluding batteries which have a 180 Day Limited Warranty)
• ADJ DMX Controllers = 2 Year (730 Days)
  • American Audio Products = 1 Year (365 Days)

SAFETY GUIDELINES

For Your Own Personal Safety, Please Read and Understand This Manual Completely Before You Attempt To Install Or Operate This Unit!

• Be sure to save the packing carton in the unlikely event the device may have to be returned for service.
• Do not spill water or other liquids into or on to the device.
• Be sure that the local power outlet matches the required voltage for the device.
• Do not open up the device for any reason. There are no user serviceable parts inside.
• Disconnect the device's main power when left unused for long periods of time.
• Never connect this device to a dimmer pack.
• Do not attempt to operate this device if it has been damaged in any way.
• Never operate this device with the cover removed.
  • To reduce the risk of electrical shock or fire, do not expose this device to rain or moisture.
  • Do not attempt to operate this device if the power cord has been frayed or broken.
• Do not attempt to remove or break off the ground prong from the electrical cord. This prong is used to reduce the risk of electrical shock and fire in case of an internal short.
• Disconnect from main power before making any type of connection.
• Never block the ventilation holes. Always be sure to mount this device in an area that will allow proper ventilation. Allow about 6" (15cm) between this device and a wall.
  • This unit is intended for indoor use only. Use of this product outdoors voids all warranties.
  • Always mount this unit in a safe and stable matter.
• Please route your power cord out of the way of foot traffic. Power cords should be routed so they are not likely to be walked on, or pinched by items placed upon or against them.

Maximum ambient operating temperature for this fixture is 113 degrees F (45 degrees C). Do not operate this device when ambient temperature exceeds this value!

Keep flammable materials away from this fixture!

FIXTURE IS DESIGNED FOR INDOOR USE ONLY! DO NOT EXPOSE TO RAIN OR MOISTURE!

The device should be serviced by qualified service personnel when:

A. The power-supply cord or the plug has been damaged.
B. Objects have fallen on, or liquid has been spilled into, the device.
C. The device has been exposed to rain or water.
D. The appliance does not appear to operate normally or exhibits a marked change in performance.

OVERVIEW

Net In Fuse (T6.3A 250V) Power In Power Out Net Out DMX In (5-pin) DMX Out (5-pin) DMX Out (3-pin) Carry Handle DCMX In (3-pin) Mode Button Up Button Display Screen Left Button Down Button Enter Button Right Button Tilt Lock (on side of yoke) Pan Lock

Omega Bracket Attachments Safety Cable Loop

DMX SET UP

DMX-512: DMX is short for Digital Multiplex. This is a universal protocol used as a form of communication between intelligent fixtures and controllers. A DMX controller sends DMX data instructions from the controller to the fixture. DMX data is sent as serial data that travels from fixture to fixture via the DATA "IN" and DATA "OUT" XLR terminals located on all DMX fixtures (most controllers only have a DATA "OUT" terminal).

DMX Linking: DMX is a language allowing all makes and models of different manufacturers to be linked together and operate from a single controller, as long as all fixtures and the controller are DMX compliant. To ensure proper DMX data transmission, try to use the shortest cable path possible when linking several DMX fixtures. The order in which fixtures are connected in a DMX line does not influence the DMX addressing. For example, a fixture assigned a DMX address of 1 may be placed anywhere in a DMX line: at the beginning, at the end, or anywhere in the middle. When a fixture is assigned a DMX address of 1, the DMX controller knows to send DATA assigned to address 1 to that unit, no matter where it is located in the DMX chain.

Data Cable (DMX Cable) Requirements (For DMX Operation): The Focus Profile can be controlled via DMX-512 protocol. The DMX address is set on the front panel of the fixture. Your unit and your DMX controller require a standard 3-pin XLR connector for data input and data output. We recommend Accu-Cable DMX cables. If you are making your own cables, be sure to use standard 110-120 Ohm shielded cable (This cable may be purchased at almost all pro lighting stores). Your cables should be made with a male XLR connector at one end and a female XLR connector on the other. Also remember that DMX cable must be daisy chained and cannot be split.

Notice: Be sure to follow figures 1 and 2 when making your own cables. Do not use the ground lug on the XLR connector. Do not connect the cable's shield conductor to the ground lug or allow the shield conductor to come in contact with the XLR's outer casing. Grounding the shield could cause a short circuit and may result in erratic behavior.

COMMON DMX512 OUT 3-PIN XLR 10 30 20 DMX + DMX - 1 3 2 DMX512 IN 3-PIN XLR

Figure 1

XLR Male Socket 1 Ground 2 Cold 3 Hot XLR Female Socket 2 Cold 1 Ground 3 Hot

Figure 2

XLR Pin Configuration

Pin 1 = Ground

Pin 2 = Data Compliment (negative)

Pin 3 = Data True (positive)

DMX SET UP

Special Note: Line Termination. When longer runs of cable are used, you may need to use a terminator on the last unit to avoid erratic behavior. A terminator is a 110-120 ohm 1/4 watt resistor which is connected between pins 2 and 3 of a male XLR connector (DATA + and DATA -). This unit is inserted in the female XLR connector of the last unit in your daisy chain to terminate the line. Using a cable terminator (ADJ part number Z-DMX/T) will decrease the possibilities of erratic behavior.

Termination reduces signal errors and avoids signal transmission problems and interference. It is always advisable to connect a DMX terminal, (Resistance 120 Ohm 1/4 W) between PIN 2 (DMX-) and PIN 3 (DMX +) of the last fixture.

5-Pin XLR DMX Connectors. Some manufacturers use 5-pin DMX-512 data cables for DATA transmission in place of 3-pin. 5-pin DMX fixtures may be implemented in a 3-pin DMX line. When inserting standard 5-pin data cables into a 3-pin line, a cable adaptor must be used. These adaptors are readily available at most electronics stores. The chart below details a proper cable conversion.

3-Pin XLR to 5-Pin XLR Conversion
Conductor	3-Pin XLR Female (Out)	5-Pin XLR Male (In)
Ground/Shield	Pin 1	Pin 1
Data Compliment (- signal)	Pin 2	Pin 2
Data True (+ signal)	Pin 3	Pin 3
Not Used		Do Not Use
Not Used		Do Not Use

INSTALLATION

IP RATING

This device is IP20 rated. It is protected against instrusion of solids larger than 12.5mm in size, or approximately the size of an adult finger. The device is NOT protected against liquid instrusion of any kind.

FLAMMABLE MATERIAL WARNING!

Keep device a minimum of 5.0 feet (1.5m) away from flammable material and/or pyrotechnics.

ELECTRICAL CONNECTIONS

A qualified electrician should be used for all electrical connections and/or installations.

MULTI-DEVICE DAISY CHAINING

• When connected to 240V power, up to 2 devices may be daisy chained together.
• When connected to 110V power, daisy chaining is NOT permitted. In this situation, only operate the fixture as a single standalone device!

DO NOT INSTALL THE DEVICE IF YOU ARE NOT QUALIFIED TO DO SO!

The unit MUST be installed following all local, national, and country commercial electrical and construction codes and regulations.

Before installing or mounting any device, a professional equipment installer MUST be consulted to determine whether the mounting structure or surface is properly certified to safely support the combined weight of the fixture, clamps, cables, and accessories.

Overhead fixture installations must always be secured with a secondary safety attachment, such as an appropriately rated safety cable that meets all local, national, and country codes and regulations.

Maximum ambient operating temperature is 113^ (45°C). Do not operate this device when ambient temperature exceeds this value.

This fixture should be installed in areas outside walking paths, seating areas, and areas where unauthorized personnel might be able to reach the device by hand.

NEVER stand directly below the fixture when rigging, removing, or servicing.

Allow approximately 15 minutes for the fixture to cool down before servicing.

INSTALLATION

POTENTIAL INTERNAL FIXTURE DAMAGE FROM EXTERNAL SOURCES OF LIGHT BEAMS

External sources of light beams from direct sunlight, lighting moving head fixtures, and lasers which are focused directly towards the exterior housing and/or penetrate the front lens opening of ADJ lighting fixtures can cause severe internal damage including burning of optics, dichroic color filters, glass and metal gobos, prisms, animation wheels, frost filters, irises, shutters, motors, belts, wiring, discharge lamps, and LEDs.

This issue is not unique to ADJ lighting fixtures; it is a common issue with lighting fixtures from all manufacturers. Although there is no true way to fully prevent this issue from happening, the guidelines below can reduce the risk of any potential damage if followed. Contact ADJ Service for more details.

DO NOT EXPOSE THE FIXTURE AND/OR FRONT LENS OPENING TO LIGHT BEAMS FROM DIRECT SUNLIGHT, OTHER LIGHTING MOVING HEAD FIXTURES, AND LASERS DURING UNPACKING, INSTALLATION, USE, AND EXTENDED IDLE TIMES OUTDOORS. DO NOT FOCUS A LIGHT BEAM FROM ONE LIGHTING FIXTURE DIRECTLY TOWARDS ANOTHER.

This fixture features multiple mounting clamp attachment points, as well as a safety cable attachment point, located on the bottom face of the fixture (see the illustration below). When mounting the fixture to a truss or any other suspended or overhead installation, be sure to secure appropriately rated clamps (not included) to the clamp attachment points and attach a separate SAFETY CABLE of the appropriate safety rating to the safety cable rigging point.

SAFETY CABLE ATTACHMENT MOUNTING CLAMP ATTACHMENT POINT

SAFETY CABLE

ALWAYS ATTACH A SAFETY CABLE WHENEVER INSTALLING THIS FIXTURE IN A SUSPENDED ENVIRONMENT TO ENSURE THAT THE FIXTURE WILL NOT FALL IF THE CLAMP FAILS.

RIGGING

Overhead rigging requires extensive experience, including but not limited to: calculating working load limits, understanding the installation material being used, and periodic safety inspection of all installation material and the fixture itself. If you lack these qualifications, do not attempt to perform the installation yourself. Improper installation can result in bodily injury.

INSTALLATION

NOTICE: The max suitable environmental temperature for this lighting fixture is 45^ C. Do not place this lighting fixture in an environment where the temperatures exceed this rating. This will allow the fixture to run at its best and help prolong the fixture life.

The Focus Profile is fully operational in three different mounting positions: hanging upside-down from a ceiling or trussing, sideways on trussing, or set on a flat level surface. Be sure this fixture is kept at least 12m (40ft) away from any flammable materials (decoration etc.). Always use and install a safety cable (not included) as a safety measure to prevent accidental damage and/or injury in the event the clamp fails. Never use the carrying handles for secondary attachment.

GOBO REPLACEMENT

1. Engage both the pan and tilt locks. Use a screwdriver to loosen the 4 fasteners that secure the cover (left), then unclip the security cable (right) and remove the cover. Repeat this process for both halves of the cover.

Front view of a black industrial lighting fixture with red circular annotations pointing to specific components (no visible text or symbols)

Close-up of a mechanical assembly with visible gears, springs, and a red arrow pointing to a component (no text or symbols)

1. Position the head so that the side with the small fan (located near the bottom of the head) is facing towards you. Locate the gobo wheel module, which prominently features a row of 3 stepper motors. From there, find and disconnect the electrical connector on the right-hand side of the module, near the effect wheel.

Stepper Motors Small Fan Electrical Connector

GOBO REPLACEMENT

1. Locate the two screws that hold the gobo wheel module in place. The first screw is located below and left of the stepper motors, and the second is located below and right of the electrical connector that was disconnected in Step 2.

Interior view of a robotic vehicle showing internal components and wiring, with red arrows pointing to specific parts (no text or symbols visible)

1. Remove the gobo wheel module from the head. Locate the open area between the left-most stepper motor and the gobo wheel. This is the location that will be used to remove the desired gobo. Please beware of damaging the sensor beneath the gobo wheel at this location.

SENSOR LOCATION GOBO ACCESS

GOBO REPLACEMENT

1. Rotate the replaceable gobo wheel (top wheel) so that the gobo you wish to replace is positioned near the open area just behind the left-most stepper motor. Then rotate the non-replaceable gobo wheel (bottom wheel) so that the open slot is aligned with the gobo you wish to replace. The top image shows the 2 gobo wheels out of alignment; the bottom image shows the 2 wheels aligned as desired.

REPLACEABLE GOBO WHEEL NON-REPLACEABLE GOBO WHEEL (UNALIGNED) NON-REPLACEABLE GOBO WHEEL (ALIGNED)

GOBO REPLACEMENT

1. Firmly grasp the holder of the gobo you wish you replace by the toothed gear portion. Lift the gobo upward, gently pushing from below with a finger if necessary (left), then pull the holder outward (right) to remove from the gobo wheel.

Close-up of hands assembling a device with visible circuitry and wiring (no text or symbols)

Close-up of hands assembling a computer case with visible gears and components (no text or symbols)

1. Turn the holder over so that the gear side is facing downwards. Carefully use a pick to catch the spring tab and release the retainer spring (left). Be careful to avoid scratching the gobo. Remove the retainer spring, then remove the gobo (right).

SPRING TAB

Close-up of a hand holding a small object with a red upward arrow, next to a black ring (no text or symbols visible)

GOBO REPLACEMENT

1. Place the new gobo in the gobo holder, and re-install the retainer spring.

2. Manually rotate the silver central gear of the gobo wheel so that the positioning mark is aligned with the slot where you will be installing the new gobo.

TPM-STEP 100-13 200-250 POSITIONING MARK HP-STEP M 140/2004-13

1. Turn the gobo holder back over so that the gear side is facing upwards. Position the mark on the gobo holder so that it aligns with the mark on the gobo wheel, then slide the prong on the gobo holder into the slot on the gobo wheel until it clicks into place.

GOGO WHEEL MARK GOBO HOLDER MARK

1. Re-assemble the moving head by reversing steps 1-4.

CONTROL PANEL

This fixture includes an easy to navigate control panel display, from which all necessary settings and adjustments can be made. During normal operation, pressing the MODE button once will access the fixture's main menu. Once in the main menu, the UP and DOWN buttons can be used to navigate through the different functions. Press the ENTER button to select the option displayed on the screen, and use the LEFT and RIGHT buttons to adjust the settings for the selected option. Press the ENTER button once more to confirm the setting. Press the MODE button at any time to return to the main menu without making any adjustments.

The fixture also includes an internal battery that allows users to operate the screen and control panel even when the fixture is not plugged in. To access the system menu when the fixture is running on internal battery power, press and hold the MODE button to illuminate the display screen until the DMX address is displayed, then navigate to the desired system menu.

Please note that the battery is only capable of powering the screen and control panel, and that the fixture is NOT capable of illuminating while on battery power.

The screen display can be quickly inverted without navigating through the system menu. To do so, simply press the RIGHT button once to invert the display, and press the RIGHT button again to undo the display inversion.

MODE UP ENTER LEFT DOWN RIGHT

SYSTEM MENU

DMX SETTINGS	Set Address	A001~AXXX
	DMX Channel Mode	Standard 40
		Basic 36
		Extended 51
	No DMX Status	Hold Last
		Blackout
		Manual
PERSONALITY	Status Settings	Primary	On / Off
		Secondary	On / Off
		Pan Degree	630 / 540
		Pan Invert	On / Off
		Tilt Invert	On / Off
		P./T. Feedback	On / Off
		P.T. Speed	Speed1 / Speed2
		Hibernation	Off, 01M~99MDefault = 15M
	Fixture ID	Service PIN Password = 050
		Universe 000 - 255
		UnitIPAddr xxx.xxx	xxx.xxx
		Mask Addr xxx.xxx	xxx.xxx
	ProtocolSet	ArtNet
		sACN
	Net Switch	On / Off
	Fan Settings Head		Auto
			High
			Silent
	Dim Modes	Standard
		Stage
		TV
		Architecur
		Theatre
		Stage2
		Dim Speed 0.1S ~ 10S
CONTINUED ON NEXT PAGE

SYSTEM MENU

PERSONALITY (cont'd from prev page)	LED Refresh Rate	900Hz~1500Hz, 2500Hz, 4000Hz, 5000Hz, 6000Hz, 10KHz, 15KHz, 20KHz, 25KHz		Default = 15KHz
	Dim Curve	Linear
		Square
		Inverse Square
		S-Curve
	CT Mode	Off / On
	Reset Motors	Reset All Motors	Yes / No
		Pan/Tilt Reset	Yes / No
		Color Reset	Yes / No
		Gobo Reset	Yes / No
		Effect/Focus Reset	Yes / No
		Focus/Zoom Reset	Yes / No
		Other Reset	Yes / No
	Display	Intensity	1~10
		Display Invert	Yes / No
		Screen Saver Delay	Off ~ 10M Default = 5M
		Key Lock	Off / On / On1
	Service (Password = 050)	Effect Adjust	Pan Pan Fine Tilt ...
		USB Port Power On /	Off
		Update Software Yes /	No
		Factory Restore Yes /	No Passcode = 011
MANUAL CONTROL	Pan 000-255
	Pan Fine 000-255
	Tilt 000-255
	Tilt Fine 000-255
	Color1 000-255
	Color2 000-255
	Gobo1 000-255
	Gobo1Rot 000-255
CONTINUED ON NEXT PAGE

SYSTEM MENU

MANUALCONTROL(cont'd from prev page)	Gobo2 000-255
	Gobo2Rot 000-255
	Shutter 000-255
	Dimmer 000-255
	Dimmer Fine 000-255
	Prism 1 000-255
	Prism 1 Rot 000-255
	Prism 1 Rot Fine 000-255
	Prism 2 000-255
	Prism 2 Rot 000-255
	Prism 2 Rot Fine 000-255
	Focus 000-255
	Zoom 000-255
	Iris 000-255
	Frost1 000-255
	Frost2 000-255
	Dim Modes 000-255
	Dim Curve 000-255
	P/T Speed 000-255
	Special Function	000-255
INTERNALPROGRAMS	Program 1	Speed	000-255
		Fade	000-255
	Program 2	Speed	000-255
		Fade	000-255
	Program 3	Speed	000-255
		Fade	000-255
	Program 4	Speed	000-255
		Fade	000-255
	Program 5	Speed	000-255
		Fade	000-255
CONTINUED ON NEXT PAGE

SYSTEM MENU

INTERNAL PROGRAMS (cont'd from prev page)	Program 6	Speed 000-255
		Fade 000-255
	Program 7	Speed 000-255
		Fade 000-255
INFORMATION	Fixture Life Time	Power On Time xxxxxx Hours
		P-On Time-R xxxxxx Hours
		P-On Time-Reset Passcode = 050
	Total LED Time	LED On Time xxxxxx Hours
		LED ON Time-R xxxxxx Hours
		LED Hours Reset Passcode = 050
	Fixture Temps	LEDs	Current	F / C
			Max Resettable
			Max Not Resettable
		Base Temp
		Reset LED Temp Passcode = 050
		Reset Base Temp Passcode = 050
	Fan Info (RPM)	LED Fan 1
		LED Fan 2
		LED Fan 3
		LED Fan 4
		LED Fan 5
		Gobo Fan
		Motor Fan
		Base Fan1
		Base Fan2
	DMX Values	Pan
		Tilt
		...
		Special Function
	Error Logs	Fixture Errors	List Errors One by One	Passcode = 050
		Reset Error Log	Yes / No
	Software Version

DMX ADDRESSING

All fixtures should be given a DMX starting address when operating with a DMX controller, in order to ensure that the correct fixture responds to the correct control signal. This digital starting address is the channel number from which the fixture starts to “listen” to the digital control signal sent out from the DMX controller. The assignment of this starting DMX address is achieved by setting the correct DMX address on the digital control display on the fixture.

You can set the same starting address for all fixtures or a group of fixtures, or set different addresses for each individual fixture. Setting all fixtures to the same DMX address will cause all fixtures to react in the same way. In this case, please note that changing the settings of one channel will affect all the fixtures simultaneously.

If you set each fixture to a different DMX address, each unit will start to "listen" to the channel number you have set, based on the quantity of DMX channels of each fixture. That means changing the settings of one channel will only affect the selected fixture.

As an example, when operating this fixture model in 36 channel mode, you should set the starting DMX address of the first unit to 1, the second unit to 37 (36 + 1), the third unit to 73 (1 + 36 + 36), and so on. (See the chart below for more details.)

Channel Mode Unit 1 Address Unit 2 Address Unit 3 Address Unit 4 Address
36 Channels	1 37 73 109
40 Channels	1 41 81 121
51 Channels	1 52 103 154

DMX TRAITS

CHANNEL			VALUES FUNCTION
36-CH	40-CH 51-CH
1 1 1	000 - 25	5
	2 2 0	00 - 255
2 3 3	000 - 25	5
	4 4 0	00 - 255
3 5 5	000 - 25	5
		6 000 - 255	Cyan Fine
4 6 7	000 - 25	5
		8 000 - 255	Magenta Fine
5 7 9	000 - 25	5
		10 000 - 255	Yellow Fine
6 8 1	1 000 - 2	55
		12 000 - 255	CTO Fine
7 9 13
			White Color Temperature Presets
			000 - 023 Open
			024 - 069 See White Color Temperature Presets section
			070 - 255 6700K
8 10	14
			Color Wheel
			000 - 005 Color off (open)
			006 - 011 Red
			012 - 017 Blue
			018 - 023 Green
			024 - 029 Yellow
			030 - 035 CRI
			035 - 041 CTB
			042 - 047 Color off (open)
			048 - 059 Open - Red
			060 Red
			061 - 070 Red - Blue
			071 Blue
			072 - 081 Blue - Green
CONTINUED ON NEXT PAGE

DMX TRAITS

CHANNEL			VALUES FUNCTION
36-CH	40-CH 51-CH
8 10	14			Color Wheel (continued)
			082 Green
			083 - 092 Green - Yellow
			093 Yellow
			094 - 104 Yellow - CRI
			105 CRI
			106 - 116 CRI - CTB
			117 CTB
			118 - 126 CTB - Open
			127 Color off (open)
			128 - 190 Clockwise color wheel rotation, fast to slow
			191 - 192 Stop color wheel rotation
			193 - 255 Counter-clockwise color wheel rotation, slow to fast
9 11	15			Rotating Gobos, continuous rotation
			000 - 006 Open
			007 - 013 Gobo 1
			014 - 020 Gobo 2
			021 - 027 Gobo 3
			028 - 034 Gobo 4
			035 - 041 Gobo 5
			042 - 048 Gobo 6
			049 - 055 Gobo 7
			056 - 062 Gobo 1 shake, slow to fast
			063 - 069 Gobo 2 shake, slow to fast
			070 - 076 Gobo 3 shake, slow to fast
			077 - 083 Gobo 4 shake, slow to fast
			084 - 090 Gobo 5 shake, slow to fast
			091 - 097 Gobo 6 shake, slow to fast
			098 - 104 Gobo 7 shake, slow to fast
CONTINUED ON NEXT PAGE

DMX TRAITS

CHANNEL			VALUES FUNCTION
36-CH	40-CH	51-CH
9 11	15			Rotating Gobos, continuous rotation (continued)
			105 - 178 C	Clockwise gobo wheel rotation, fast to slow
			179 - 181 S	Stop gobo wheel rotation
			182 - 255 C	Counter-clockwise gobo wheel rotation, slow to fast
10 12	16			Gobo Rotation
			000 - 127 G	Gobo Rotation Indexing
			128 - 190 C	Clockwise Gobo Rotation, fast to slow
			191 - 192 S	Stop Gobo Rotation
			193 - 255 C	Counter-clockwise Gobo Rotation, slow to fast
		17 000 - 255		Gobo Rotation Indexing, Fine
11 13	18			Fixed Gobos, continuous rotation
			000 - 006 Open
			007 - 013 Gobo 1
			014 - 020 Gobo 2
			021 - 027 Gobo 3
			028 - 034 Gobo 4
			035 - 041 Gobo 5
			042 - 048 Gobo 6
			049 - 055 Gobo 7
			056 - 062 Gobo 8
			063 - 069 Gobo 1 shake, slow to fast
			070 - 076 Gobo 2 shake, slow to fast
			077 - 083 Gobo 3 shake, slow to fast
			084 - 090 Gobo 4 shake, slow to fast
			091 - 097 Gobo 5 shake, slow to fast
			098 - 104 Gobo 6 shake, slow to fast
			105 - 111 Gobo 7 shake, slow to fast
			112 - 118 Gobo 8 shake, slow to fast
			119 - 185 C	Clockwise fixed gobo wheel rotation, fast to slow
			186 - 188 S	Stop fixed gobo wheel rotation
			189 - 255 C	Counter-clockwise fixed gobo wheel rotation, slow to fast
CONTINUED ON NEXT PAGE

DMX TRAITS

CHANNEL			VALUES F	FUNCTION
36-CH	40-CH 51	-CH
12 14	19			Shutter, Strobe
			000 - 031 No function (shutter closed)
			032 - 063 No action, shutter open
			064 - 095 Strobe, slow to fast
			096 - 127 No action, shutter open
			128 - 159 Pulse effect, slow to fast
			160 - 191 No action, shutter open
			192 - 223 Random strobe, slow to fast
			224 - 255 No action, shutter open
13 15	20 000	255		Dimmer Intensity, 0% to 100%
	16 21	000 - 255		Dimmer Fine, 0% to 100%
14 17	22			Prism 1
			000 - 031 No effect
			032 - 255 Prism 1 (3 facet)
15 18	23			Prism 1 Rotation
			000 - 127 Prism 1 indexing
			128 - 189 Clockwise rotation, fast to slow
			190 - 193 No rotation
			194 - 255 Counter-clockwise rotation, slow to fast
		24 000	0 - 255	Prism 1 Index Fine
16 19	25			Prism 2
			000 - 031 No effect
			032 - 255 Prism 2 (4-facet)
17 20	26			Prism 2 Rotation
			000 - 127 Prism 2 indexing
			128 - 189 Clockwise rotation, fast to slow
			190 - 193 No rotation
			194 - 255 Counter-clockwise rotation, slow to fast
		27 000	0 - 255	Prism 2 Index Fine
18 21	28 000	255		Focus, continuous adjustment, far to near
		29 000	0 - 255	Focus Fine
CONTINUED ON NEXT PAGE

DMX TRAITS

CHANNEL			VALUES FUNCTION
36-CH	40-CH 51-CH
19 22	30 000	255		Zoom, minimum to maximum beam angle
		31 000	0 - 255	Zoom Fine
20 23	32			Iris
			000 - 191 Diameter, maximum to minimum
			192 - 223 Pulse opening, fast to slow
			224 - 255 Pulse closing, slow to fast
		33 000	0 - 255	Iris Fine
21 24	34 000	255		Frost, open to full frost
22 25	35			Animation Indexing and Rotation
			000 - 005 Open
			006 - 127 Animation indexing
			128 - 189 Clockwise animation rotation, fast to slow
			190 - 193 No rotation
			194 - 255 Counter-clockwise animation rotation, slow to fast
23 26	36 000	255		Blade 1A, 0% to 100%
24 27	37 000	255		Blade 1B, 0% to 100%
25 28	38 000	255		Blade 2A, 0% to 100%
26 29	39 000	255		Blade 2B, 0% to 100%
27 30	40 000	255		Blade 3A, 0% to 100%
28 31	41 000	255		Blade 3B, 0% to 100%
29 32	42 000	255		Blade 4A, 0% to 100%
30 33	43 000	255		Blade 4B, 0% to 100%
31 34	44			Frame Rotation
			000 - 126 Minimum (-60 degrees)
			127 - 128 Parallel (0 degrees)
			129 - 255 Maximum (+60 degrees)
		45 000	0 - 255	Frame Rotation Fine
32 35	46 000	255		Frame Speed, maximum to minimum
CONTINUED ON NEXT PAGE

DMX TRAITS

CHANNEL			VALUES FUNCTION
36-CH	40-CH 51-CH
33 36	47
			Frame Macros (see Frame Macros Chart for details)
			000 - 007 Off
			008 - 015 Macro1
			016 - 023 Macro2
			024 - 031 Macro3
			032 - 039 Macro4
			040 - 047 Macro5
			048 - 055 Macro6
			056 - 063 Macro7
			064 - 071 Macro8
			072 - 079 Macro9
			080 - 087 Macro10
			088 - 095 Macro11
			096 - 103 Macro12
			104 - 111 Macro13
			112 - 119 Macro14
			120 - 127 Macro15
			138 - 135 Macro16
			136 - 143 Macro17
			144 - 151 Macro18
			152 - 159 Macro19
			160 - 167 Macro20
			168 - 175 Macro21
			176 - 183 Macro22
			184 - 191 Macro23
			192 - 199 Macro24
			200 - 207 Macro25
			208 - 215 Macro26
			216 - 223 Macro27
			224 - 231 Macro28
CONTINUED ON NEXT PAGE

DMX TRAITS

CHANNEL			VALUES FUNCTION
36-CH	40-CH 51	-CH
33 36	47			Frame Macros (continued, see Frame Macros Chart for details)
			232 - 239 Macro29
			240 - 247 Macro30
			248 - 255 Macro31
34 37	48			Dim Modes
			000 - 020 Standard
			021 - 040 Stage
			041 - 060 TV
			061 - 080 Architectural
			081 - 100 Theatre
			101 - 120 Stage 2
			121 - 140 Dim Speed, fast to slow, 0.1s to 10s
			141 - 255 Default
	38 49			Dim Curves
			000 - 020 Linear
			021 - 040 Square
			041 - 060 Inv. Squa
			061 - 080 S. Curve
			081 - 255 No Function
35 39	50 000 -	255		Pan/Tilt Speed, maximum to minimum speed
36 40	51			Special Functions, Reset, & Internal Programs
			000 - 005 No function
			006 - 010 Normal operation, default refresh rate = 1200 Hz
			011 900 Hz
			012 910 Hz
			013 920 Hz
			014 930 Hz
			015 940 Hz
			016 950 Hz
			017 960 Hz
CONTINUED ON NEXT PAGE

DMX TRAITS

CHANNEL			VALUES FUNCTION
36-CH	40-CH 51	-CH
36 40	51			Special Functions, Reset, & Internal Programs (cont'd)
			018 970 Hz
			019 980 Hz
			020 990 Hz
			021 1000 Hz
			022 1010 Hz
			023 1020 Hz
			024 1030 Hz
			025 1040 Hz
			026 1050 Hz
			027 1060 Hz
			028 1070 Hz
			029 1080 Hz
			030 1090 Hz
			031 1100 Hz
			032 1110 Hz
			033 1120 Hz
			034 1130 Hz
			035 1140 Hz
			036 1150 Hz
			037 1160 Hz
			038 1170 Hz
			039 1180 Hz
			040 1190 Hz
			041 1210 Hz
			042 1220 Hz
			043 1230 Hz
			044 1240 Hz
			045 1250 Hz
			046 1260 Hz
CONTINUED ON NEXT PAGE

DMX TRAITS

CHANNEL			VALUES FUNCTION
36-CH	40-CH 5	1-CH
36 40	51			Special Functions, Reset, & Internal Programs (cont'd)
			047 1270 Hz
			048 1280 Hz
			049 1290 Hz
			050 1300 Hz
			051 1310 Hz
			052 1320 Hz
			053 1330 Hz
			054 1340 Hz
			055 1350 Hz
			056 1360 Hz
			057 1370 Hz
			058 1380 Hz
			059 1390 Hz
			060 1400 Hz
			061 1410 Hz
			062 1420 Hz
			063 1430 Hz
			064 1440 Hz
			065 1450 Hz
			066 1460 Hz
			067 1470 Hz
			068 1480 Hz
			069 1490 Hz
			070 1500 Hz
			071 2500 Hz
			072 4000 Hz
			073 5000 Hz
			074 6000 Hz
			075 10,000 Hz
CONTINUED ON NEXT PAGE

DMX TRAITS

CHANNEL			VALUES FUNCTION
36-CH	40-CH 51	-CH
36 40	51
			Special Functions, Reset, & Internal Programs (cont'd)
			076 15,000 Hz
			077 20,000 Hz
			078 25,000 Hz
			079 Disable LED Refresh Rate
			080 - 085 Enable blackout while pan/tilt moving
			086 - 091 Disable blackout while pan/tilt moving
			092 - 097 Enable blackout while color changing
			098 - 103 Disable blackout while color changing
			104 - 109 Enable blackout while gobo changing
			110 - 115 Disable blackout while gobo changing
			116 - 121 All motors reset
			122 - 127 Pan/tilt reset
			128 - 133 Effect reset
			134 - 139 Color reset
			140 - 145 Gobo reset
			146 - 151 Focus and zoom reset
			152 - 157 Other motors reset
			158 - 163 Fan mode low
			164 - 169 Fan mode high
			170 - 175 Fan mode auto
			176 - 179 Idle
			180 - 189 Internal program 1 (scenes 1-8)
			190 - 199 Internal program 2 (scenes 9-16)
			200 - 209 Internal program 3 (scenes 17-24)
			210 - 219 Internal program 4 (scenes 25-32)
			220 - 229 Internal program 5 (scenes 33-40)
			230 - 239 Internal program 6 (scsnes 41-48)
			240 - 249 Internal program 7 (scenes 49-56)
			250 - 252 Enable CT mode
			253 - 255 Disable CT mode

WHITE COLOR TEMPERATURE PRESETS

DMX VALUE	COLOR TEMP	DMX VALUE	COLOR TEMP
024 2700	045 4800
025 2800	046 4900
026 2900	047 5000
027 3000	048 5100
028 3100	049 5200
029 3200	050 5300
030 3300	051 5400
031 3400	052 5500
032 3500	053 5600
033 3600	054 5700
034 3700	055 5800
035 3800	056 5900
036 3900	057 6000
037 4000	058 6100
038 4100	059 6200
039 4200	060 6300
040 4300	061 6400
041 4400	062 6500
042 4500	063 6600
043 4600	064 6700
044 4700

COLOR WHEEL

GOBOS

Rotating Gobos

1 2 3 4 5 6 7

Fixed Gobos

1 2 3 4 5 6 7 8

DIMMER MODES AND CURVES

Dimming Curve Ramp Effect	0 sec Fade Time		1 sec Fade Time
	255		255
	Rise Time (ms)	Down Time (ms)	Rise Time (ms)	Down Time (ms)
Standard (default)	0	0	0	0
Stage	780	1100	1540	1660
TV	1180	1520	1860	1940
Architectural	1380	1730	2040	2120
Theatre	1580	1940	2230	2280
Stage 2	0	1100	0	1660

FRAME MACROS TABLE

FRAME MACRO NO.	BLADE 1A	BLADE 1B	BLADE 2A	BLADE 2B	BLADE 3A	BLADE 3B	BLADE 4A	BLADE 4B
1 150	0 150 0 15	0 0 150 0
2 138	116 126 0	162 206 88	146
3 146	0 208 70 1	66 0 162 168
4 220	0 122 0 16	6 0 114 64
5 0 10	4 0 124 0 1	62 64 132
6 88 7	4 132 240	84 144 114	60
7 144	74 0 255 1	0 108 48 116
8 138	116 198 0	162 106 11	2 78
9 96 1	00 0 130 1	62 0 0 172
10 138	216 134 0	0 206 88 146
11 88	94 0 244 46	112 114 44
12 138	216 140 0	0 206 0 0
13 124	62 216 0 1	108 206					126 2
14 152	118 128 1	06 136 102	68 114
15 124	54 0 154 1	6 118 126	206
16 0 21	4 2 146 0	124 0 128
17 144	74 0 152 1	0 240 138	74
18 102	120 56 20	2 30 102 152	40
19 174	104 100 1	24 194 152	64 132
20 88	74 132 240	84 102 114	172
21 86	112 168 0 2	28 26 122	64
22 146	0 208 70 1	66 0 162 0
23 138	116 126 0	162 206 11	2 78
24 150	154 150 0	150 0 150	86
25 122	0 0 196 15	0 0 150 86
26 182	0 98 124 1	62 64 0 168
27 210	0 120 0 16	6 0 162 0
28 88	92 150 0 22	8				144 114 0
29 122	0 0 130 16	2 0 220 86
30 124	54 216 15	4 16 118 126	2
31 138	116 198 1	42 0 160 138	80

CLEANING AND MAINTENANCE

WARNING! DISCONNECT UNIT FROM POWER BEFORE PERFORMING ANY CLEANING OR MAINTENANCE PROCEDURES!

ALWAYS ALLOW THE FIXTURE TO COOL FOR AT LEAST 15 MINUTES BEFORE PERFORMING ANY CLEANING OR MAINTENANCE!

CLEANING

Frequent cleaning is recommended to ensure proper function, optimized light output, and an extended life. The frequency of cleaning depends on the environment in which the fixture operates: damp, smoky, or particularly dirty environments can cause greater accumulation of dirt on the fixture's optics. Clean periodically with a soft cloth to avoid dirt/debris accumulation.

NEVER use alcohol, solvents, or ammonia-based cleaners.

MAINTENANCE

Regular inspections are recommended to insure proper function and extended life. There are no user serviceable parts inside this fixture. Please refer all other service issues to an authorized ADJ service technician. Should you need any spare parts, please order genuine parts from an authorized ADJ dealer.

Please refer to the following points during routine inspections:

• A detailed electrical check by an approved electrical engineer every three months, to make sure the circuit contacts are in good condition and prevent overheating.
• Be sure all screws and fasteners are securely tightened at all times. Loose screws may fall out during normal operation, resulting in damage or injury as larger parts could fall.
• Check for any deformations on the housing, color lenses, rigging hardware and rigging points (ceiling, suspension, trussing). Deformations in the housing could allow for dust to enter into the fixture. Damaged rigging points or unsecured rigging could cause the fixture to fall and seriously injure a person(s).
  • Electric power supply cables must not show any damage, material fatigue or sediments.

FUSE REPLACEMENT

Disconnect the unit from the power source, then use a flat head screw driver to unscrew the fuse holder located next to the Power In port. Remove the bad fuse and replace with a new one, then screw the fuse holder back in. Replace only with a new fuse of the same type and rating.

Fuse Location

SOFTWARE UPDATES

ONLY QUALIFIED TECHNICIANS SHOULD PERFORM THIS FUNCTION! NOTE ALL MENU SETTINGS BEFORE UPDATING SOFTWARE!

FIXTURE SOFTWARE CANNOT BE DOWNGRADED!

DOWNLOAD FIXTURE SOFTWARE TO PC ONLY! (NO MAC SUPPORT)

PLEASE CONTACT ADJ CUSTOMER SERVICE FOR FURTHER INFORMATION.

1. Contact ADJ customer service to obtain the updated software. Download software to a USB flash drive. In order to minimize the risk of downloading the incorrect software to your device, make sure that the desired update files are the only files on the USB flash drive.
2. Disconnect any DMX connections from your device. Insert the USB flash drive into the service port on your device.
3. Use the display screen control panel to navigate to Personality > Service > USB Port Power. See the System Menu section of this manual for detailed instructions. Enter the passcode when prompted, and switch the USB Port Power setting to ON.
4. Highlight the desired file and press ENTER to select it and begin the download.
5. The unit will now update, run an automatic software check, and reset. This may take some time.
6. Repeat this process for each software update file.
7. Verify by navigating to Information > Software Version and confirming that the correct software version number is shown there (see the System Menu section of this manual for detailed instructions).

DIMENSIONAL DRAWINGS

Drawings may not be to scale.

SPECIFICATIONS

SOURCE

• 400W LED Engine
  • 20,000 Hour Average LED Life

PHOTOMETRIC DATA

• 20,000 Total Lumens, 6,700K, >70CRI
• 44,330 LUX 4,118 FC @16.4' (5m) (7.32° Beam)
• 1,767 LUX 164 FC @16.4' (5m) (45° Beam)

EFFECTS

• 4 Rotating Framing Shutters plus shape rotation
• 3 & 6 Facet Rotating Prisms
- Variable Frost
- Animation wheel
- Motorized Focus
- Motorized Iris
• Electronic Dimming & Strobe (1-20Hz)

COLOR

• Full CMY color mixing
- Variable CTO
- Colors Wheel with 6 dichroic colors

GOBOS

• (2) Gobo Wheels
- #1 - (7) Interchangeable Rotating-Indexing Gobos
• #2 - (8) Static-Stamped Gobos

CONTROL / CONNECTIONS

• (3) DMX Channel Modes (33 / 36 / 48)
• RDM (Remote Device Management)
- 6 Button Touch Control Panel
• Full Color 180° Reversible LCD Menu Display
• 8 / 16 Bit Resolution Adjustable Movement
• 3 & 5 pin XLR DMX In/Out
• RJ45 Ethernet In/Out (Art-NET)
- Locking In/Out power connections
- With Wired Digital Communication Network

SIZE / WEIGHT

• Length: 25.6" (651mm)
• Width: 15.7" (400mm)
• Vertical Height: 10.2" (260mm)
• Weight: 61.2 lbs. (27.75kg)

ELECTRICAL / THERMAL

• AC 100-240V - 50/60Hz
• Max Power Consumption: 560W
- Max ambient temperature: -13°F to 113°F (-25°C to 45°C)
• Max housing temperature: 136°F (58°C)

TECHNICAL DATA

• DB Rating @ 3ft.: 49dB
• BTU Rating @ 3ft.: 113°F (45°C)

APPROVALS / RATINGS

• CE | ETL
  • IP20

Specifications and documentation subject to change without prior written notice.

ERROR CODES

ERROR CODES

PanTiltLEDTempLEDFan1LEDFan2LEDFan3LEDFan4MotorFan1CyanMagentaYellowCTOLEDFan5ColorGobo1Gobo1RotGobo2AnimationGoboFanBladeZoomFocusFrostPrism1Prism1RotPrism2Prism2RotBaseTempBaseFan1BaseFan2