VTC-TTAT2HR2F - Security Camera Vitek - Free user manual and instructions

USER MANUAL VTC-TTAT2HR2F Vitek

Exterior view of two white surveillance cameras with visible lens and camera blades (no text or symbols on the cameras themselves)

FEATURES

• 1/3" 2.1 MegaPixel CMOS Sensor
• HD-TVI & AHD/CVBS Video Output
- 2.8\~12mm Varifocal Lens (VTC-TTAT2HR2V) or 3.6mm Fixed Lens Options (VTC-TTAT2HR2F)
- 2 High Power Infrared LED's with 100' IR Range (VTC-TTAT2HR2V) / 65' IR Range (VTC-TTAT2HR2F)
• Digital Wide Dynamic Range (D-WDR)
• True Mechanical Day/Night function by ICR
• 3D-DNR Noise Reduction
• IP66 Weather Resistance
• Supports Up The COAX Control
• Over 1500' HD Video Transmission (Depending on cable characteristics and integrity)
- Optional Junction Box Mount Available (VT-TJB01) / Wall Mount (VT-TWM03) Also Available for VTC-TTAT2HR2V
- 12VDC Operation

Safety Precaution

- To prevent electrical shock and risk of fire hazards, do not expose this unit to rain or moisture and only use specified power source..

CAUTION RISK OF ELECTRIC SHOCK . DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTICAL SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL

The symbol is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electrical shock.

The symbol is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the unit.

- Warning :

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at their own expense.

- Caution :

Any changes or modifications in construction of this device which are not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

Main power quality should be that of a typical commercial environment. If the user of the model requires continued operation during power interruptions, it is recommended that the device be powered from an uninterruptible power supply (UPS).

Components and Accessories

Camera		Hex Wrench
User Manual		Mounting Plate
Screws

Overview

This camera series supports both fixed and varifocal lenses. Please note that the zoom and focus features mentioned below are not features of the fixed lens version.

1 2 Focus Zoom 3 4 5 6 7 8

1	Lens	5	Power Cable
2	Focus*	6	AHD/CVBS Switch
3	Zoom*	7	AHD/CVBS Output
4	Lock Screws	8	HD-TVI Output

*VTC-TTAT2HR2V Only

Video Connection

Connect the HD-TVI Video or AHD/CVBS video connector to a BNC patch cable, then to DVR. HD-TVI DVR Monitor

patch cable, then to DVR. HD-TVI DVR VGA HDMI Video Monitor Focus Zo om

AHD/CVBS Switch:

Switch to CVBS Mode: Press & Hold the Switch for 5 seconds

Switch to AHD Mode: Press & Release the Switch quickly

Power Connection

Connect the power connector to a 12 VDC power adaptor.

Power 12VDC - - +

Installation

Before you begin, please make sure that the wall or ceiling is strong enough to withstand 3 times the weight of the camera. The mounting steps are as follows:

1. Attach the drill template to the place where you want to install the camera, then drill 3 screw holes and 1 cable hole (if you want to route the cables through the mounting base) according to the drill template

2. Route the cables and connect the power & video cables, then secure the mounting base to the ceiling or wall with screws.

3. Loosen the lock screws, then adjust the camera to obtain the optimism viewing angle. Confirm the correct viewing angle with a monitor. (See next page for location of lock screws)

Pure geometric diagram of a circular mechanical or electrical component with internal gear-like shapes and mounting holes (no text or symbols)

n k Fo dB 20 cm

Installation

1. Tighten the lock screws to secure the viewing angle adjustments.

Focus Zoom

1. Adjust the Focus and Zoom screws to achieve a clear image (if your camera has a fixed lens, please skip this step).

Focus Zoom

1. Carefully remove the protective film from the lens to complete the installation.

Focus s 200 m

Camera OSD Menu

The Transcendent HD-TVI/AHD camera series must be connected to a DVR which supports HD-TVI/AHD video signal input and COC protocol to access the OSD setup menu. Different DVRs manufacturers may have different modes of menu operation.

The following menu toolbar will pop up by right-clicking the mouse when using VITEK Transcendent Series HD-TVI DVRs.

Screenshot of a software toolbar with icons for file, grid, media, and options like IPC, REC, and navigation buttons.

You will see the following interface by clicking the button.

01 02 03 04 05 06 07 08 09 10 11 12 13 14 15 16 All Zoom + Focus + Iris + Preset preset095 Cruise Start Track Start Auto Scan Start Cruise Speed: 5

Click "Iris +" to go to the main menu. You can also select preset NO.95, then click the ↗ button (call preset NO.95) to go to the following main menu.

MAIN MENU
1. LENS	MANUAL
2. EXPOSURE
3. BACKLIGHT	OFF
4. WHITE BAL	AWB
5. DAY&NIGHT	EXT ↙
6. NR
7. SPECIAL
8. ADJUST
9. EXIT	SAVE&END ↙

You can select the menu by clicking ▲ (U) or ▼ (D) key on the direction area. Click □ (L) or ▶ (R) key to select the menu on the left. The menu with arrow icon which means it has sub-menu. You can select the menu and click “Iris +” or call preset NO.95 to enter the sub-menu. To return to the previous menu or exit the main menu, please select “RET” or “Save & END” by clicking U or D key and then click “Iris +” or call preset NO.95.

Detailed Specifications VTC-TTAT2HR2F VTC-TTAT2HR2V

Image Sensor	1/3" 2.1 MegaPixel CMOS Sensor
Resolution	1080p (2.1 MegaPixel)
Effective Pixels	1920(H) x 1080(V)
Signal System	PAL/NTSC
Video Output	1x HD-TVI (BNC) & 1 AHD/CVBS (BNC)
Lens	3.6mm Fixed	2.8~12mm (Vari-Focal)
Day/Night	True Day/Night by ICR
S/N Ratio	>52dB (AGC OFF)
Auto Gain Control	OFF ~ 44.8dB
Min Illumination	0 Lux (LED ON)
IR LEDs	2 x High Power	2 x High Power
IR Distance	65'	100'
Color-B/W Auto Switch	Yes
Electronic Shutter	1/50s~ 1/67500s
White Balance	AWB
WB Range	2300~9600K
BLC	Yes
WDR	Digital WDR
Transmission Distance	Up to 1500' (Depending on cable characteristics & integrity)
Up the COAX Control	YES
Noise Reduction	Yes
Weather Resistance	IP66
Power Supply	12VDC
Working Environment	-4~122 / 10%~90% Humidity
Weight	13.05 oz. / 0.82 lbs. / 370g	24.30 oz. / 1.52 lbs. / 689g
Dimensions	3.43" x 4.25" (87 × 108mm) Dia x H	4.29" x 5.12" (109 × 130mm) Dia x H

TRANSCENDENT

VITEK

Two black VITEK connectors connected by a cable, no visible text or symbols on the devices themselves.

VT-TR4K

Passive Video Balun Transmitter/Receiver pair (2ea included) for TVI/AHD/CVI for distances from 680 to 1400'. Built in Surge suppression and 60dB noise immunity

OPTIONAL ACCESSORIES FOR TRANSCENDENT CAMERAS

Two black VITEK Ethernet connectors with attached cables, no visible text or symbols on the devices themselves.

VT-TR4VPK

Video & Power Balun Transmitter/Receiver pair (2ea included) for TVI/AHD/CVI for distances from 680 to 1400'. Built in Surge suppression and 60dB noise immunity

3D rendering of a white plastic enclosure with internal compartments and mounting holes (no text or symbols)

VT-TJB01

Optional Junction Box for Cable Management for use with all Transcendent Bullet and Turret Style Cameras

Exterior view of a white wall-mounted security camera (no text or symbols visible)

VT-TWM03

Wall Mount for Transcendent 30 IR LED Vandal Domes and Varifocal Turret Cameras

LIMITED PRODUCT WARRANTY

VITEK products carry a three (3) year limited warranty. VITEK warrants to the purchaser that products manufactured by VITEK are free of any rightful claim of infringement or the like, and when used in the manner intended, will be free of defects in materials and workmanship for a period of three (3) years, or as otherwise stated above, from the date of purchase by the end user. This warranty is nontransferable and extends only to the original buyer or end user customer of a VITEK Authorized Reseller.

The product must have been used only for its intended purpose, and not been subjected to damage by misuse, willful or accidental damage, caused by excessive voltage or lightning.

The product must not have been tampered with in any way or the guarantee will be considered null and void.

This guarantee does not affect your statutory rights.

Contact your local VITEK Reseller should servicing become necessary.

VITEK makes no warranty or guarantee whatsoever with respect to products sold or purchased through unauthorized sales channels. Warranty support is available only if product is purchased through a VITEK Authorized Reseller.