VTC-THB5R3 - Security Camera Vitek - Free user manual and instructions

USER MANUAL VTC-THB5R3 Vitek

Transcendent 5.0 Megapixel Indoor/

Outdoor 4-IN-1 HDA Cameras w/IR LED

Illumination

Three white surveillance cameras with different camera designs and mounting brackets (no visible text or symbols)

FEATURES

• 1/2.5" 5.0 Megapixel Progressive Scan CMOS Sensor
  • High Definition Analog (HDA): HD-TVI & AHD: 5.0 MegaPixel / CVI: 4.0 MegaPixel / CVBS: 960H Video Output
  • 3.6mm Fixed Lens
  • Infrared LED's with up to 120' IR Range
  • Digital Wide Dynamic Range (D-WDR)
  • True Mechanical Day/Night function by ICR

• 2D-DNR Noise Reduction
• IP66 Weather Resistance & IK10 Impact Rating
• Supports Up The COAX Control
• Over 1500' HD Video Transmission (Depending on cable characteristics and integrity)
- Optional Junction Box & Wall Mounts Available
• 12VDC Operation
• 3 Year Warranty

TRANSCENDENT

VITEK

Safety Precaution

• To prevent electrical shock and risk of fire hazards, do not expose this unit to rain or moisture and only use specified power source..

CAUTION: TO REDUCE THE RISK OF ELECTICAL SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL

The symbol is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electrical shock.

The symbol is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the unit.

Warning :

* This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at their own expense.

Caution :

• Any changes or modifications in construction of this device which are not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

Main power quality should be that of a typical commercial environment. If the user of the model requires continued operation during power interruptions, it is recommended that the device be powered from an uninterruptible power supply (UPS).

Limited Product Warranty

VITEK products carry a three (3) year limited warranty. VITEK warrants to the purchaser that products manufactured by VITEK are free of any rightful claim of infringement or the like, and when used in the manner intended, will be free of defects in materials and workmanship for a period of three (3) years, or as otherwise stated above, from the date of purchase by the end user. This warranty is nontransferable and extends only to the original buyer or end user customer of a VITEK Authorized Reseller.

The product must have been used only for its intended purpose, and not been subjected to damage by misuse, willful or accidental damage, caused by excessive voltage or lightning.

The product must not have been tampered with in any way or the guarantee will be considered null and void.

This guarantee does not affect your statutory rights.

Contact your local VITEK Reseller should servicing become necessary.

VITEK makes no warranty or guarantee whatsoever with respect to products sold or purchased through unauthorized sales channels. Warranty support is available only if product is purchased through a VITEK Authorized Reseller.

VTC-THB5R3 Components

Camera		Screws
User Manual		Drill Template

Overview

Technical diagram of a mechanical device with numbered components, likely a camera or sensor assembly.

1	Lens	5	BNC Video Output
2	Sun Shield	6	Output Mode Switch
3	Mount Lock	7	Power Cable
4	Mount Base

Video Connection

Connect the BNC video connector to a BNC cable, then to a DVR.

DVR VGA HDMI Monitor Video

Video Output Mode Switch:

Select the desired video mode using the dip switches contained within the on-cable Output Mode Switch as follows:

Power Connection

Connect the power connector to a regulated 12 VDC power adaptor.

Power 12VDC

Installation

Before you begin, please make sure that the wall or ceiling is strong enough to withstand 3 times the weight of the camera. The mounting steps are as follows:

1. Attach the drill template to the place where you want to install the camera, then drill 3 screw holes and 1 cable hole (if you want to route the cables through the mounting base) according to the drill template

Simple circular diagram with a central cross and four corner symbols (no text or labels)

1. Loosen the mount lock to adjust the Pan and Tilt of the camera, then tighten the mount lock to secure the viewing angle adjustments.

360° Pan 90° Tilt

1. Route the cables and connect the power & video cables, then secure the mounting base to the ceiling or wall with screws.

Technical line drawing of a mechanical device with no visible text or symbols

Ceiling Mounted

Technical line drawing of a mechanical assembly with no visible text or symbols

Wall Mounted

1. Carefully remove the protective film from the lens to complete the installation.

Protective Lens Film

VTC-THT5R3 Components

Camera		Hex Wrench	[TZGC]
Manual	[COCW]	Mounting Plate	[XOSS]
Screws	[SCBW]	Rubber Plug	[SKKS]

Overview

1 2 3 4 5

1	Lens	4	Output Mode Switch
2	Lock Screws	5	Power Cable
3	BNC Video Output

Video Connection

Connect the BNC video connector to a BNC cable, then to a DVR.

DVR H0-TV1 VIDEO IN VGA HDMI Video Monitor

Video Output Mode Switch:

Select the desired video mode using the dip switches contained within the on-cable Output Mode Switch as follows:

Power Connection

Connect the power connector to a regulated 12 VDC power adaptor.

Power 12VDC

Installation

Before you begin, please make sure that the wall or ceiling is strong enough to withstand 3 times the weight of the camera. The mounting steps are as follows:

1. Attach the drill template to the place where you want to install the camera, then drill 3 screw holes and 1 cable hole (if you want to route the cables through the mounting base) according to the drill template
2. Route the cables and connect the power & video cables, then secure the mounting base to the ceiling or wall with screws.
3. Loosen the lock screws, then adjust the camera to obtain the optimism viewing angle. Confirm the correct viewing angle with a monitor. Next insert the rubber plug.

Circular diagram with a central rectangular block and symmetrical cutouts, no text or symbols present.

Rubber Plug

1. Tighten the lock screws to secure the viewing angle adjustments.

Technical line drawing of a mechanical component with concentric rings and a circular base, shown with an inset detail (no text or symbols)

1. Carefully remove the protective film from the lens to complete the installation.

Protective Lens Film

VTD-THD2RFE Components

Camera		Screws
Manual		Hex Wrench
Drill Template

Overview

1 2 3 4 5

1	Mounting Base	4	Output Mode Switch
2	Dome Cover	5	Power Cable
3	BNC Video Output

Video Connection

Connect the BNC video connector to a BNC cable, then to a DVR.

DVR H0-1VI VIDEO IN VGA HDMI Video Monitor

Video Output Mode Switch:

Select the desired video mode using the dip switches contained within the on-cable Output Mode Switch as follows:

Power Connection

Connect the power connector to a regulated 12 VDC power adaptor.

Power 12VDC

Installation

Before beginning installation, make sure that the wall or ceiling is strong enough to withstand 3 times the weight of the camera. The mounting steps are as follows:

1. Attach the drill template to the place where you want to install the camera, then drill the screw holes and 1 cable hole according to the drill template.
2. Loosen the screws to open the lower dome and then loosen the lock screw to remove the mounting base.
3. Route the cables and connect the power & video cables, use the rubber plug to fill the gap of the mounting base, then secure the mounting base to the ceiling or wall with screws.

Rubber Plug

1. Adjust the Three-axis camer bracket to obtain the optimism viewing angle.

Pan: 0°~240° Rotation: 0°~220° Tilt: 0°~68°

1. Install the dome bubble on the camera with the screws, then carefully remove the protective film to complete the installation.

Technical diagram of a mechanical assembly with an upward arrow indicating motion or force (no text or symbols present)

Camera OSD Menu

The Transcendent 4-in1 camera series must be connected to a DVR which supports HD-TVI/AHD video signal input and COC protocol to access the OSD setup menu. Different DVRs manufacturers may have different modes of menu operation.

The Following image will pop-up when you left click once on the image when using Transcendent HDA DVR's.

You will see the following interface by clicking the PTZ button.

Camera DCT Mono Preset Delete

Click on the OSD tab and then click on the camera menu button.

MAIN MENU
1. LENS	MANUAL
2. EXPOSURE
3. BACKLIGHT	OFF
4. WHITE BAL	AWB
5. DAY&NIGHT	EXT
6. NR
7. SPECIAL
8. ADJUST
9. EXIT	SAVE&END

You can select the menu by clicking ▲(U) or ▼(D) key on the direction area. Click □(L) or ▶(R) key to select the menu on the left. The menu with arrow icon which means it has sub-menu. You can select the menu and click the Enter Button ← to enter the sub-menu. to return to previous screen, arrow down to Return and click Enter Button. To Exit menu arrow down to Exit and click Enter Button.

Detailed Specifications VTC-THB5R3 VTC-THT5R3 VTD-THD5R3

Image Sensor	1/2.5" 5.0 Megapixel Progressive Scan CMOS Sensor
Signal System	PAL/NTSC
Effective Pixels	2592 x 1944
Resolution	HD-TVI & AHD: 5.0 MegaPixel / CVI: 4.0 MegaPixel / CVBS: 960H
Video Output	HD-TVI / AHD / CVI / CVBS (Selectable)
Frame Rate	20fps
Lens	3.6 mm (Fixed)
Day/Night	True Day/Night by ICR
Min. Illumination	Color: 0.001 lux@F1.2, AGC ON / B/W: 0 lux (with IR ON)
IR LEDs	36 Dynamic Intensity LEDs	30 Dynamic Intensity LEDs	16 Dynamic Intensity LEDs
IR Distance	120'	65'	65'
S/N Ratio	≥52dB (AGC Off)
WDR	D-WDR
Defog	YES
Digital Noise Reduction (DNR)	2D-DNR
White Balance	Auto (AWB)
BLC	YES
Up the COAX Control (COC)	YES
Transmission Distance	Up to 1500' (Depending on cable characteristics & integrity)
Power Input	12VDC
Power Consumption (12VDC)	IR On: 120mA / IR Off: 360mA	IR Off: 120mA / IR On: 480mA	IR Off: 120mA / IR On: 480mA
Weather Resistance	IP66		IP66 / IK10
Operation Conditions	-4~122 / 10%~90% Humidity
Weight	20.81 oz. / 1.30 lbs. / 590g	13.05 oz. / 0.82 lbs. / 370g	21.34 oz. / 1.33 lbs. / 605g
Dimensions	3.43 x 8.62" (87mm x 219mm) Dia x L	3.43" x 4.25" (87 × 108mm) Dia x H	4.57" x 3.58" (116mm×91mm) Dia x H

TRANSCENDENT VARIFOCAL 4-IN-1 CAMERAS ALSO AVAILABLE!

Exterior view of a white surveillance camera with mounted lens and mounting flange (no text or symbols visible)

VTC-THB5RV
Transcendent 5.0 Megapixel Indoor/Outdoor 4-IN-1 HDA Varifocal Bullet Camera w/36 IR LED Illumination

Exterior view of a modern surveillance camera (no visible text or symbols)

VTD-THD5RV
Transcendent 5.0 Megapixel Indoor/Outdoor 4-IN-1 HDA Varifocal Dome Camera w/30 IR LED Illumination

OPTIONAL MOUNTS FOR FIXED TRANSCENDENT CAMERAS

VT-TJB01
Optional Junction Box for Cable Management for use with all Transcendent Bullet and Turret Style Cameras

VT-TJB03A
Optional Junction Box for Cable Management for use with Select Transcendent Vandal Dome Cameras

VT-TWMT3
Optional Wall Mount for use with most Transcendent Fixed Domes and Turrets.

28492 CONSTELLATION ROAD VALENCIA, CA 91355 WWW.VITEKCCTV.COM

Version 1.0

December 2017