VTC-TTAB36R2V - Security Camera Vitek - Free user manual and instructions

USER MANUAL VTC-TTAB36R2V Vitek

Two white surveillance cameras with black caps and metallic blades, no visible text or symbols on the devices themselves.

FEATURES

• 1/3" 2.1 MegaPixel CMOS Sensor
• HD-TVI & AHD/CVBS Video Output
- 3.6mm Fixed Lens (VTC-TTAB42R2F) / 2.8\~12mm Varifocal Lens (VTC-TTAB36R2V)
• 42 Infrared LED's with 150' IR Range (VTC-TTAB42R2F) / 36 Infrared LED's with 120' IR Range (VTC-TTAB36R2V)
• Digital Wide Dynamic Range (D-WDR)
• True Mechanical Day/Night function by ICR
• 3D-DNR Noise Reduction
• IP66 Weather Resistance
• Supports Up The COAX Control
• Over 1500' HD Video Transmission (Depending on cable characteristics and integrity)
- Optional Junction Box Mount Available (VT-TJB01)
• 12VDC Operation

Safety Precaution

- To prevent electrical shock and risk of fire hazards, do not expose this unit to rain or moisture and only use specified power source..

CAUTION RISK OF ELECTRIC SHOCK . DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTICAL SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL

The symbol is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electrical shock.

The symbol is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the unit.

- Warning :

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at their own expense.

- Caution :

Any changes or modifications in construction of this device which are not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

Main power quality should be that of a typical commercial environment. If the user of the model requires continued operation during power interruptions, it is recommended that the device be powered from an uninterruptible power supply (UPS).

Components and Accessories

Camera		Screws
User Manual		Drill Template

Overview

This camera series supports both fixed and varifocal lenses. Please note that the zoom and focus features mentioned below are only available on the varifocal lens version.

Technical diagram of a security camera with labeled components and internal wiring connections

1	Lens	7	Focus*
2	Sun Shield	8	HD-TVI Output
3	Mount Lock	9	AHD/CVBS Output
4	Mount Base	10	AHD/CVBS Switch
5	Lens Cover	11	Power Cable
6	Zoom*

*VTC-TTAB36R2V Only

Video Connection

Connect the HD-TVI Video or AHD/CVBS video connector to a BNC patch cable, then to DVR.

DVR VGA HDMI Monitor Video

AHD/CVBS Switch:

Switch to CVBS Mode: Press & Hold the Switch for 5 seconds Switch to AHD Mode: Press & Release the Switch quickly

Power Connection

Connect the power connector to a 12 VDC power adaptor.

Power 12VDC

Installation

Before you begin, please make sure that the wall or ceiling is strong enough to withstand 3 times the weight of the camera. The mounting steps are as follows:

1. Attach the drill template to the place where you want to install the camera, then drill 3 screw holes and 1 cable hole (if you want to route the cables through the mounting base) according to the drill template

Simple circular diagram with a central crosshair and four corner symbols (no text or labels)

1. Route the cables and connect the power & video cables, then secure the mounting base to the ceiling or wall with screws.

Technical line drawing of a mechanical device with no visible text or symbols

Ceiling Mounted

Technical line drawing of a mechanical device with no visible text or symbols

Wall Mounted

Installation

1. Loosen the mount lock to adjust the Pan and Tilt of the camera, then tighten the mount lock to secure the viewing angle adjustments.

360° Pan 90° Tilt

1. To adjust the lens, start by removing the Lens Cover, then adjust the Focus and Zoom levers to achieve a clear image. Replace the Lens Cover. (if your camera is Fixed lens, please skip this step)

Lens Cover Zoom Focus

1. Carefully remove the protective film from the lens to complete the installation.

Camera OSD Menu

The Transcendent HD-TVI/AHD camera series must be connected to a DVR which supports HD-TVI/AHD video signal input and COC protocol to access the OSD setup menu. Different DVRs manufacturers may have different modes of menu operation.

The following menu toolbar will pop up by right-clicking the mouse when using VITEK Transcendent Series HD-TVI DVRs.

Screenshot of a software toolbar with icons for file, grid, media, and options like IPC, REC, and navigation buttons.

You will see the following interface by clicking the button.

01 02 03 04 05 06 07 08 09 10 11 12 13 14 15 16 All Zoom + Focus + Iris + Preset preset095 Cruise Start Track Start Auto Scan Start Cruise Speed: 5

Click "Iris +" to go to the main menu. You can also select preset NO.95, then click the ↗ button (call preset NO.95) to go to the following main menu.

MAIN MENU
1. LENS	MANUAL
2. EXPOSURE
3. BACKLIGHT	OFF
4. WHITE BAL	AWB
5. DAY&NIGHT	EXT ↙
6. NR
7. SPECIAL
8. ADJUST
9. EXIT	SAVE&END ↙

You can select the menu by clicking ▲ (U) or ▼ (D) key on the direction area. Click □ (L) or ▶ (R) key to select the menu on the left. The menu with arrow icon which means it has sub-menu. You can select the menu and click “Iris +” or call preset NO.95 to enter the sub-menu. To return to the previous menu or exit the main menu, please select “RET” or “Save & END” by clicking U or D key and then click “Iris +” or call preset NO.95.

Detailed Specifications VTC-TTAB42R2F VTC-TTAB36R2V
Image Sensor	1/3" 2.1 MegaPixel CMOS Sensor
Resolution	1080p (2.1 MegaPixel)
Effective Pixels	1920(H) x 1080(V)
Signal System	PAL/NTSC
Video Output	1x HD-TVI (BNC) & 1 AHD/CVBS (BNC)
Lens	3.6mm Fixed 2.8~12mm (Vari-Focal)
Day/Night	True Day/Night by ICR
S/N Ratio	>52dB (AGC OFF)
Auto Gain Control	OFF ~44.8dB
Min Illumination	0 Lux (LED ON)
IR LEDs	42 36
IR Distance	150' 120'
Color-B/W Auto Switch	Yes
Electronic Shutter	1/50s~ 1/67500s
White Balance	AWB
WB Range	2300~9600K
BLC	Yes
WDR	Digital WDR
Transmission Distance	Up to 1500' (Depending on cable characteristics & integrity)
Up the COAX Control	YES
Noise Reduction	Yes
Weather Resistance	IP66
Power Supply	12VDC
Working Environment	-4~122 / 10%~90% Humidity
Weight	20.81 oz. / 1.30 lbs. / 590g 21.16 oz. / 1.32 lbs. / 600g
Dimensions	3.43 x 8.62" (87mm x 219mm) Dia x L

LIMITED PRODUCT WARRANTY

VITEK products carry a three (3) year limited warranty. VITEK warrants to the purchaser that products manufactured by VITEK are free of any rightful claim of infringement or the like, and when used in the manner intended, will be free of defects in materials and workmanship for a period of three (3) years, or as otherwise stated above, from the date of purchase by the end user. This warranty is nontransferable and extends only to the original buyer or end user customer of a VITEK Authorized Reseller.

The product must have been used only for its intended purpose, and not been subjected to damage by misuse, willful or accidental damage, caused by excessive voltage or lightning.

The product must not have been tampered with in any way or the guarantee will be considered null and void.

This guarantee does not affect your statutory rights.

Contact your local VITEK Reseller should servicing become necessary.

VITEK makes no warranty or guarantee whatsoever with respect to products sold or purchased through unauthorized sales channels. Warranty support is available only if product is purchased through a VITEK Authorized Reseller.