230-DE3 - Système d'installation Alltemp - Free user manual and instructions

USER MANUAL 230-DE3 Alltemp

SpeedChannel is produced with 100% e new able en e gY TÜV SUD

DIVERSITECH

SpeediChannel™

System Installation

Contents

Introduction

3 DiversiTech Speedichannel™ System
4 Features and Benefits

System Installation

6 Step 1
7 Step 2
8 Step 3
9 Step 4
10 Step 5
11 Step 6

Installation Diagrams

12 Indoor and Outdoor installations
14 Flex Joint and Drain Hose diagrams
16 Line Set configuration
17 Air Handler installations

Sizing Chart

21 Dimensions and Capacities

Technical Information

22 General data and safety information

Mini Component Guide

23 Product information and product layout

DiversiTech SpeediChannel™ System

DiversiTech SpeediChannel™ is an innovative channel system used to cover air conditioning line sets. The two part system has a base and a cover. The base is fastened to a wall or ceiling, then a clever little plastic clip (SpeediClip™) snaps into a channel already molded into the base. SpeediClip™ is the fastest, most convenient way to complete a line set cover installation. Then, using standard cable ties, the line set, cables, control wires, and/or condensate drain line are fastened in place. The cover then simply snaps on top of the base.

The SpeediChannel™ system is available in three widths - 3", 4", and 6". Each piece of SpeediChannel™ is 6-1/2 feet long. A complete line of couplings, elbows, and tees are available for the SpeediChannel™ system.

Manufactured from rigid PVC, the SpeediChannel™ system is a natural color that is a very close match to the typical mini split condensing unit case. However, the SpeediChannel™ system can be painted as desired to match any wall color. The PVC used in the SpeediChannel™ system is resistant to UV light, and is UL rated.

DiversiTech recommends attaching the base to the wall or ceiling and the line sets to the system every 15" to allow for the system to carry the full weight of the

line sets.

The SpeediChannel™ system can also

be used inside.

Features and Benefits

SpeediClipTM	· SpeediClipTM simply slides into place on a railing molded into the inside of the SpeediChannelTM allowing for single person installation. Competitive products must be screwed in place which is extremely time consuming.
Paintable	· The SpeediChannelTM can be easily customized to any wall construction. *See painting specifications below.
Natural color	· The original natural color blends well with almost any wall construction aesthetic.
Large size	· DiversiTech's large SpeediChannelTM size is a full 6" channel — unlike competitors' products which are only 5-1/2".
Tight fit corner and flat bottom channel design	· The flat bottom channel sits on surfaces easier and fits into corners better. It can be silicone sealed against the wall.
Stainless steel screws	· Stainless steel screws will not rust.
Flat wall escutcheon	· Competitive products have a larger escutcheon that is not aesthetically pleasing and wastes space.
Integrated flex joint	· Competitive products require a joiner piece to couple the flex joint to their systems. The DiversiTech flex joint slides right into the end of the SpeediChannelTM with no additional joiner piece.
Long radius 90° bend	· DiversiTech's long radius 90° bend allows for a larger bending radius for the line set, making installation easier.

Features and Benefits

Single piece wall sleeve

20mm drain line with double connections

True Y connection

English packaging

- Competitive products are multi-part which is cumbersome.

- Versatile — fits 16, 18, or 20mm drain line.

- Drainline Y is inline. It does not branch.

- Competitive products have Japanese on the boxes, potentially leading to product selection errors.

Painting Specifications

DiversiTech recommends any 100% acrylic latex or 100% acrylic latex with a urethane additive when painting SpeediChannel products. The reason for this recommendation is because of the paint's flexibility. Lacquers are not recommended with PVC products because lacquers are more brittle and won't flex with the channel. Some suggestions: Duration by Sherwin Williams, Manor Hall paints by PPG and Moorelife by Benjamin Moore. In addition to paint type, only light-to-medium colored paints (Light Reflectance Value of 55% units or greater) should be applied to SpeediChannel or most any exterior PVC products. Light Reflectance Value (LRV) is a measurement that indicates how much light a color reflects. An LRV of 0% is absolute black and an LRV of 100% is perfectly reflective white. LRV is on the back of most color swatches and in the index of all major brands' fandecks. It is not safe to assume the paint is a light color. Some paints that appear light beige can have an LRV in the 20s or 30s.

Step 1

Attach the SpeediChannel™ base to the wall about every 15 inches with screws suitable for the wall construction (siding, stucco, brick, etc.).

Screw through the center of the molded rail. Slide the connecting piece (elbow, union, tee, etc.) under the SpeediChannel™ before attaching the end of the channel to the wall. When cutting lengths of SpeediChannel™, allow 1/8" gap between the end of the SpeediChannel™ and the stop inside the fitting to allow for thermal expansion.

serler of the molded rail. Slade the elbow, union, tee, etc.) under the before attaching the end of the . When cutting lengths of allow 1/8" gap between ediChannel™ and the ing to allow for

Step 2

Slide one SpeediClip™ with cable tie about every 20 inches along the inside sliding rail.

Close-up of a hand adjusting a white plastic bracket on a wooden surface, with no visible text or symbols.

Step 3

Install the line set, drain line, and wires inside the SpeediChannel™. Test the equipment installation prior to tightening the cable ties. Tighten the cable ties snug, but not so tight they damage the tubing insulation or kink the drain line. Trim excess length from the cable tie.

Close-up of hands installing a flexible hose on a wall panel, no text or symbols visible

Step 4

Attach the SpeediChannel™ to the base.

the SpeediChannel™ to the base.

Step 5

Attach the fitting covers with the screws provided.

Two-panel image showing a hand operating a white drill press and a person adjusting the tool on a wooden deck (no text or symbols visible)

Step 6

When complete, paint the SpeediChannel™ to match surface of installation (if desired).

Worker painting a wall-mounted tool against a wooden wall (no text or symbols visible)

Typical Detail of Indoor Installation

A B A C

A - 230-D
B-230-FB
C - 230-WC
D - 230-EB
E - 230-EIN
F - 230-DC
G - 230-FJ
H - 230-WS2
NOTE: Suffix parts A-G with the duct size needed (3,4, or 6)

E D A C

Technical line drawing of a wooden post with curved bracing and support brackets (no text or symbols)

Typical Detail of Outdoor Installation

Technical diagram of a mechanical assembly with labeled components A, C, F, and H, showing directional arrows indicating motion or flow.

Typical Detail of Flex Joint Application

B - 230-FB C - 230-WC D - 230-EB E - 230-EIN F - 230-DC G - 230-FJ H - 230-WS2 NOTE: Suffix parts A-G with the duct size needed (3,4, or 6)

Typical Detail of Cut-out for Drain Hose

Notch bottom half as shown here.

Typical Line Set, Cable, and Drain Hose Configuration

Drain Hose Insulated Refrigerant Line SpeediChannel™ Top SpeediChannel™ Bottom SpeediClip™ F - 230-DC G - 230-FJ H - 230-WS2 J - 230-CP K - 230-DE L - 230-TC NOTE: Suffix parts A-G with the duct size needed (3,4, or 6)

A - 230-D
B - 230-FB
C - 230-WC
D - 230-EB
E - 230-EIN
F - 230-DC
G - 230-FJ
H - 230-WS2
J-230-CP
K - 230-DE
L - 230-TC
NOTE: Suffix parts A-G with the duct size needed (3,4, or 6)
SpeediChannel™ Top
SpeediChannel™ Bottom
SpeediClip™

Basic Application - 1 Air Handler

C A B A J A K

Vertical Dual Air Handler System Application

System Application C A J A K

A - 230-D

B - 230-FB

C - 230-WC

D - 230-EB

E - 230-EIN

F - 230-DC

G-230-FJ

H-230-WS2

J - 230-CP

K - 230-DE

L - 230-TC

NOTE: Suffix parts A-G with the duct size needed (3,4, or 6)

Horizontal Dual Air Handler System Application

C A L A J A K C

Building with Different Wall Thickness Application

Technical diagram of a pipe or duct system with labeled components A, B, C, D, E, G and a base block, showing internal structure and connections.

A - 230-D

B - 230-FB

C - 230-WC

D - 230-EB

E - 230-EIN

F - 230-DC

G-230-FJ

H-230-WS2

J - 230-CP

K - 230-DE

L - 230-TC

NOTE: Suffix parts A-G with the duct size needed (3,4, or 6)

Sizing Chart and Selection Information

Maximum Line Set, Drain Pipe, and Cable Capacity using 3/8" Insulation

Model 30-D3 2 30-D4 2 30-D6
Dimensions	3" x 2-1/2"	4" x 2-3/4"	6" x 3"
Length	78"	78"	78"

Mini Split Systems - Liquid and Suction Line with 3/8" Insulation

Liquid Line	3/8"	2 x 1/4"	1 x 1/4" + 2 x 3/8"
Suction Line	5/8"	2 x 3/8"	1 x 1/2" + 2 x 5/8"
Drain Hose	3/4" OD	2 x 3/4" OD	3 x 3/4" OD
Power Cable	1 x UF 14-3	2 x 1/2" SealTite	3 x 1/2" SealTite
Control Cable	1 Pair 18 AWG	2 Pairs 18 AWG	3 Pairs 18 AWG
Nominal Tonnage	1–3 Tons	1x3 Ton or 2x1 Ton	1x3 Ton or 2x2 Ton

Conventional Split Systems – Liquid Line Plain, Suction Line with 3/8" Insulation

Liquid Line	3/8"	3/8"	3/8"
Suction Line	3/4" or 7/8"	1-1/8"	1-1/8"
Drain Hose	3/4" PVC	3/4" PVC	3/4" PVC
Power Cable	1 x UF 14-2	1 x 1/2" SealTite	1 x 1/2" SealTite
Control Cable	1 Pair 18 AWG	1 Pair 18 AWG	1 Pair 18 AWG
Nominal Tonnage	Up to 3.5 Tons	4-5 Tons	7.5 Tons and up

Technical Data

Color Natural
Size	230-D3: 3" x 2-1/2" OD	230-D4: 4" x 2-3/4" OD	230-D6: 6" x 3-1/8" OD	Standard Length: 78"
Material Weather Resistant PVC, UV Stabilized and Fire Resistant
Fire Rating Meets UL 94V.-0
Temperature Range	- 4°F TO 140°F
Weather Resistance	Tested to over 2,000 hours
Fixing Screws	Stainless Steel

SpeediChannel™

CATALOG NO. DESCRIPTION QTY. NEEDED
2 30-D3 3" SpeediChannelTM - 6-1/2' long
2 30-D4 4" SpeediChannelTM - 6-1/2' long
2 30-D6 6" SpeediChannelTM - 6-1/2' long

Wall Penetration

CATALOG NO. DESCRIPTION QTY. NEEDED
2 30-WC3 3" Wall Penetration
2 30-WC4 4" Wall Penetration
2 30-WC6 6" Wall Penetration
2 30-WS2 2-1/2" Wall Sleeve

Union Coupling

CATALOG NO. DESCRIPTION QTY. NEEDED
2 30-CP3 3" Union Coupling
2 30-CP4 4" Union Coupling
2 30-CP6 6" Union Coupling

90° Long Radius Flat Bend

CATALOG NO. DESCRIPTION QTY. NEEDED
2 30-LFB3 3" 90 deg Long Radius Flat Bend
2 30-LFB4 4" 90 deg Long Radius Flat Bend
2 30-LFB6 6" 90 deg Long Radius Flat Bend

90° Flat Bend

CATALOG NO. DESCRIPTION QTY. NEEDED
2 30-FB3 3" 90 deg Flat Bend
2 30-FB4 4" 90 deg Flat Bend
2 30-FB6 6" 90 deg Flat Bend

90° Inside Elbow

CATALOG NO. DESCRIPTION QTY. NEEDED
2 30-EB3 3" 90 degree Inside Elbow
2 30-EB4 4" 90 degree Inside Elbow
2 30-EB6 6" 90 degree Inside Elbow

90° Outside Elbow

CATALOG NO. DESCRIPTION QTY. NEEDED
2 30-EIN3 3" 90 degree Outside Elbow
2 30-EIN4 4" 90 degree Outside Elbow
2 30-EIN6 6" 90 degree Outside Elbow

45° Flat Bend

CATALOG NO. DESCRIPTION QTY. NEEDED
2 30-FB453 3" 45 degree Flat Bend
2 30-FB454 4" 45 degree Flat Bend
2 30-FB456 6" 45 degree Flat Bend

T-Joint

CATALOG NO. DESCRIPTION QTY. NEEDED
2 30-TJ4 4" T-Joint
2 30-TJ6 6" T-Joint

Reducer Coupling

CATALOG NO. DESCRIPTION QTY. NEEDED
2 30-TC34 3" x 4" Reducer Coupling
2 30-TC46 4" x 6" Reducer Coupling

White plastic cylindrical container with a small outlet, no visible text or symbols

White 3D cube-shaped object with a small hole at the top (no text or symbols)

White plastic curved pipe fitting with a small cylindrical component (no text or symbols visible)

White plastic mechanical component with cutouts and a slot (no text or symbols visible)

White plastic mechanical component with a rectangular cutout (no text or symbols visible)

Flex Joint

CATALOG NO. DESCRIPTION QTY. NEEDED
230-FJ3 3" Flex Joint
230-FJ4 4" Flex Joint

Duct End

CATALOG NO. DESCRIPTION QTY. NEEDED
230-DE3 3" Duct End
230-DE4 4" Duct End
230-DE6 6" Duct End

Cap

CATALOG NO. DESCRIPTION QTY. NEEDED
230-DC3 3" Cap
230-DC4 4" Cap
230-DC6 6" Cap

Flat Wall Escutcheon

CATALOG NO. DESCRIPTION QTY. NEEDED
230-FR3 3" Flat Wall Escutcheon
230-FR4 4" Flat Wall Escutcheon
230-FR6 6" Flat Wall Escutcheon

Wall Escutcheon

CATALOG NO. DESCRIPTION QTY. NEEDED
230-WR3 3" Wall Escutcheon
230-WR4 4" Wall Escutcheon
230-WR6 6" Wall Escutcheon

Mounting Blocks

CATALOG NO. DESCRIPTION QTY. NEEDED
230-MB14W 14" MountBlock (White) pack of 2
230-MB17W 17" MountBlock (White) pack of 2
230-MB36W 36" MountBlock (White) pack of 2
230-MBCW MountBlock End Cap (White) pack of 4

Condensate Drain Pans

CATALOG NO. DESCRIPTION QTY. NEEDED
230-DPPL Poly Cond Drain Pan (Large)
230-DPML Metal Cond Drain Pan (Large)
230-DPPM Poly Cond Drain Pan (Medium)
230-DPMM Metal Cond Drain Pan (Medium)

UltraLite® Equipment Pads

CATALOG NO. DESCRIPTION QTY. NEEDED
UC1636-2	16" x 36" x 2" UltraLite® Equipment Pad
UC1636-3	16" x 36" x 3" UltraLite® Equipment Pad
UC2448-2	24" x 48" x 2" UltraLite® Equipment Pad

E Lite® Equipment Pads

CATALOG NO.	DESCRIPTION	QTY.	NEEDED
EL1838-3	18" x 38" x 3" E Lite® Equipment Pad

Exterior view of a white plastic enclosure with internal compartments and a lid (no text or symbols visible)

White rectangular tray with a handle and a metal clip attached to the side (no text or symbols visible)

Plain gray rectangular block with no visible text or markings

Gray plastic tray with triangular cutouts and horizontal lines (no text or symbols)

CladLite® Equipment Pads

CATALOG NO.	DESCRIPTION	QTY. NEEDED
1636-2	16" x 36" x 2"	CladLite® Equipment Pad
1636-3	16" x 36" x 3"	CladLite® Equipment Pad

Type 2 Wall Brackets

CATALOG NO. DESCRIPTION QTY. NEEDED
230-B2L Type 2 Wall Brackets (Large)
230-B2M Type 2 Wall Brackets (Medium)
Arm Length 21" (Large), 18" (Medium)
Load Rating per Arm 220 lbs. (Large), 165 lbs. (Medium)

Type 3 Wall Brackets

CATALOG NO. DESCRIPTION QTY. NEEDED
230-B3L Type 3 Wall Brackets (Large)
230-B3M Type 3 Wall Brackets (Medium)
Arm Length 21" (Large), 19" (Medium)
Load Rating 150 lbs. (Large), 100 lbs. (Medium) per Arm

Plain gray rectangular block with rounded edges, no text or symbols visible

Metal L-shaped bracket with mounting holes (no text or symbols visible)

Simple diagram of a metal frame structure with mounting holes (no text or symbols)

DIVERSITECH

6650 Sugarloaf Parkway Duluth, GA 30097

678.542.3600 800.995.2222 678.542.3700 Fax

About DiversiTech

DiversiTech Corporation is North America's largest manufacturer of equipment pads and a leading manufacturer and supplier of components and related products for the heating, ventilating, air conditioning, and refrigeration (HVACR) industry.

Headquartered in the Atlanta, GA metropolitan area, DiversiTech manufactures a suite of products which includes a wide range of mechanical, electrical, chemical, and structural parts for HVACR and electrical systems, and swimming pool installations. The company maintains manufacturing and distribution facilities in key U.S. locations, Europe, and in the Far East. DiversiTech has enjoyed a continued history of successful growth and has acquired industry-recognized names including Devco® Enterprises, Wagner® Manufacturing, The Black Pad®, Hef-T-Pad™, and Specialty Chemical.

Send edits / corrections / comments on this catalog to [e-mail]

DOC32066 ©2017 DiversiTech Corporation Form no. LIT-INSTR-MSPLIT

Download an electronic copy of these instructions at www.diversitech.com