99-8911HG - Kit voiture Metra - Free user manual and instructions

USER MANUAL 99-8911HG Metra

Interior view of a car dashboard with air conditioners and control panels (no visible text or symbols)

Subaru Ascent 2019-up

Visit MetraOnline.com for more detailed information about the product and up-to-date vehicle specific applications

KIT FEATURES

• ISO DIN radio provision with pocket
- Painted gloss black

KIT COMPONENTS

• A) Radio trim panel • B) Radio brackets • C) Pocket • D) #8 x 3/8" Phillips screws (4) • E) Panel clips (4)

A

Technical line drawing of a door frame with mounting brackets (no text or symbols)

[Non-Text]

• 

[Non-Text]

• 

TABLE OF CONTENTS

Dash Disassembly 2

Kit Preparation 2

Kit Assembly 3

WIRING & ANTENNA CONNECTIONS (sold separately)

Wiring Harness: 70-1761

Antenna adapter: 40-LX11

Steering wheel control interface: ASWC-1

TOOLS REQUIRED

• Panel removal tool • Phillips screwdriver
• 10mm socket wrench

Attention! Let the vehicle sit with the key out of the ignition for a few minutes before removing the factory radio. When testing the aftermarket equipment, ensure that all factory equipment is connected before cycling the key to ignition.

DASH DISASSEMBLY KIT PREPA

1. Unclip and remove the a/c vent panels to the left and right of the radio. (Figure A)
2. Unclip the hazard switch panel, then set it on top the dash. (Figure B)
3. Remove (4) 10mm screws securing the radio. Slide the radio out, then unplug and remove the radio. (Figure C)

Continue to Kit Preparation

Interior view of a car dashboard with steering wheel and rearview panel (no visible text or symbols)

(Figure A) (Figure A)

Top-down view of a car interior showing the front seat, dashboard, and rear seats with no visible text or symbols

(Figure B) (Figure B)

Top-down view of a car dashboard with control panel and surrounding vehicle (no text or symbols visible)

(Figure C) (Figure C)

TION

From the factory radio brackets:

1. Loosen (8) Phillips screws securing the radio. (Figure A)
2. Remove (4) Phillips screws securing the lower electronic module then remove. (Figure A)
3. Remove (3) screws securing the upper electronic module then remove. (Figure A)
4. Relocate the lower electronic module in the radio cavity, down low. It should fit snugly, but if not, secure with zip ties. Connect the wiring harness in the vehicle back to the module.
5. Secure the upper electronic module to the radio brackets using the factory screws. (Figure B)
6. Attach (4) panel clips to the radio trim panel. (Figure C)

Continue to Kit Assembly

Left side shown Step 3 Step 2 Step 1

Technical diagram of a mechanical component with mounting flanges and housing (no text or symbols)

Technical line drawing of a mechanical component with mounting brackets and internal structure (no text or symbols)

KIT ASSEMBLY

1. Secure the pocket to the radio brackets using (4) #8 x 3/8" Phillips screws provided. (Figure A)
2. Remove the metal DIN sleeve and trim ring from the aftermarket radio.
3. Slide the radio into the bracket/pocket assembly, then secure it using the screws supplied with the radio. (Figure B)
4. Locate the factory wiring harness and antenna connector in the dash and complete all necessary connections to the radio. Metra recommends using the proper mating adapter from Metra and/or Axxess. Test the radio for proper operation.

Technical line drawing of a mechanical assembly with labeled components (no text or symbols present)

(Figure A)

1. Connect the upper electronic module back to the wiring harness in the vehicle, then slide the radio into the dash. Secure the radio using the factory screws. (Figure C)
2. Reassemble the dash in reverse order of disassembly to complete the installation.

Top-down schematic of a vehicle's internal components, showing dashboard, air vent, and control panels (no text or labels)

(Figure C)

Technical line drawing of an electronic device with ports and components (no text or symbols)

(Figure B)

If you are having difficulties with the installation of this product, contact our Tech Support line either by phone at 1-800-253-TECH, or email at [e-mail]. Before doing so, look over the instruction booklet a second time and ensure that the installation was performed exactly as the instruction booklet is stated. Have the vehicle apart and ready to perform troubleshooting steps before contacting Metra/Axxess Tech Support.

KNOWLEDGE IS POWER

Enhance your installation and fabrication skills by enrolling in the most recognized and respected mobile electronics school in our industry. Log onto www.installerinstitute.com or call 800-354-6782 for more information and take steps toward a better tomorrow.

Metra recommends MECP certified technicians

Interior view of a car dashboard with digital display and air filters (no visible text or symbols)

Exterior view of a black automotive airbox housing with mounting brackets and side panels (no text or symbols)

HARDWARE INCLUDED

Subaru Ascent 2019-up

Visit MetraOnline.com for more detailed information about the product and up-to-date vehicle specific applications.

S

ISO DIN radio provision with pocket

P

Painted high-gloss black

KIT COMPONENTS

• Radio trim panel
• Radio brackets
• Pocket

• 8 x 3/8" Phillips screws (4)

• Panel clips (4)

WIRING & ANTENNA CONNECTIONS

(sold separately)

Wiring Harness: 70-1761

Antenna adapter: 40-LX11

Steering wheel control interface: ASWC-1

SALES 800-221-0932