95-3302 - Kit voiture Metra - Free user manual and instructions

USER MANUAL 95-3302 Metra

INSTALLATION INSTRUCTIONS FOR PART 95-3302

APPLICATIONS

GM

MULTI KIT

(see models list inside)

95-3302

KIT FEATURES

• Double DIN Mount Radio Provision
- Stacked ISO Mount Radio Provision

Close-up of a medical device control panel with display and control buttons (no visible text or symbols)

KIT COMPONENTS

A) Double DIN Housing • B) Double DIN Brackets

Technical line drawing of a rectangular electronic device with mounting brackets and a central panel (no text or symbols)

Two isometric diagrams of electrical connectors or circuit breakers, labeled B (no text or symbols on the diagrams themselves)

TOOLS REQUIRED:

Small Flat Blade Screwdriver/ Panel Removal Tool

• Phillips Screwdriver • Socket Set • Cutting Tool

Line drawings of five different screwdriver tools (no text or symbols)

TABLE OF CONTENTS

Dash Disassembly

Chevrolet

-Cobalt 2005-2007 ....1
-Equinox 2005-2007 .... 2
- HHR 2006-2007 .... 3
-Malibu 2004-2007 ....4,5

Pontiac

-G5 2007 ....1
-G6 2005-2007....6
-Solstice 2006-2007 ....7
-Torrent 2006-2007 ....2

Saturn

• Aura 2007 ....8
• Ion 2006-2007 9
• Sky 2006-2007 .... 10
  -Vue 2006-2007 ....11

Kit Assembly

Double DIN Mount Radio Provision 12

Stacked ISO Mount Radio Provision 13

Note: (Malibu and G6 only)

•The Driver Information Center and radio are one unit. Removal of the radio will prohibit the vehicle owner from programming any of the features of the Driver Information Center. However once the features are programmed the vehicle will retain all the settings.
- Refer also to the instructions included with the aftermarket radio.

Chevrolet Cobalt 2005-2007/Pontiac G5 2007

1 Disconnect the negative battery terminal to prevent an accidental short circuit.
2 Unclip and remove trim panel from above glove box. (Figure A)
3 Unclip upper edge of panel below steering column and let hang. Not necessary to remove completely. (Figure B)
4 Unclip and remove small trim panel to right of ignition switch. (Figure C)
5 Unclip and remove trim panel surrounding radio and climate controls. (Figure D)
6 Remove (4) 9/32 screws securing radio. Unplug and remove the radio. (Figure E)

Continue to kit assembly.

E

Line drawing of a car infotainment system with a hand operating the dashboard (no text or symbols visible)

A

Line drawing of hands inserting a fan into a car air conditioner unit (no text or symbols)

B

Line drawing of a car interior showing steering wheel, dashboard, and steering wheel (no text or symbols)

C

Line drawing of a hand operating a device inside a vehicle (no text or symbols visible)

D

Line drawing of hands installing or adjusting a car air conditioner unit on the back panel (no text or symbols visible)

Chevrolet Equinox 2005-2007 Pontiac Torrent 2006-2007

1 Disconnect the negative battery terminal to prevent an accidental short circuit.
2 Unsnap panel below power window switch and remove. Note: This allows you to unplug the window switch easier. (Figure A)
3 Unsnap and remove entire panel surrounding radio and shifter. (Figure B)
4 Remove (4) 9/32 screws securing radio. Unplug and remove the radio. (Figure C)

Continue to kit assembly.

Diagram of hands installing or adjusting a car interior panel (no text or symbols visible)

Illustration of hands operating a handheld device with control buttons and a display screen (no text or symbols)

C

Chevrolet HHR 2006-2007

1 Disconnect the negative battery terminal to prevent an accidental short circuit.
2 Unclip and remove entire panel surrounding radio and a/c controls including the a/c vents. (Figure A)
3 Remove (8) 9/32" screws securing radio and a/c control to remove radio. (Figure B)

Continue to kit assembly.

Interior view of a car dashboard with steering wheel and hand operating controls (no text or symbols)

B

Diagram of a car interior showing dashboard, steering wheel, and internal air conditioners (no text or labels)

Chevrolet Malibu 2004-2007

1 Disconnect the negative battery terminal to prevent an accidental short circuit.
2 Unclip and remove wood grain/painted trim pieces from both sides of steering wheel. (Figure A)
3 Unclip and remove side panel from driver's side of dash with door open and remove (2) 7 MM screws. (Figure B)
4 Remove (2) 7 MM screws from bottom edge of panel below steering wheel, unclip panel and let hang. It is not necessary to completely remove panel. (Figure C)
5 Unclip and remove wood grain/painted trim piece from above glove box. (Figure D)

Diagram of a car interior showing steering wheel, dashboard, and directional arrows indicating movement (no text or symbols)

Line drawing of a person using a wrench to adjust the door panel (no text or symbols)

C

Illustration of a car interior showing hands installing or adjusting a component, no text or symbols present

Chevrolet Malibu 2004-2007

6 Unclip and remove side panel from passenger side of dash with door open and remove (2) 7 MM screws from behind panel. (Figure E)
7 Remove (2) 7 MM screws from bottom of glove box then open box and squeeze sides together to open further and remove the remaining (4) 7MM screws. Unclip the black vent cover under the glove box then unclip and remove entire glove box assembly. (Figure F)
8 Unclip and remove trim panel surrounding radio and climate controls. (Figure G)
9 Remove (4) 7 MM screws securing the radio and (2) 7 MM screws securing the climate control. Unplug and remove the radio. (Figure H)

Continue to kit assembly.

Line drawing of a hand using a tool to lift a car (no text or symbols)

F

G p₀

H

Pontiac G6 2005-2007

1 Disconnect the negative battery terminal to prevent an accidental short circuit.
2 Open glove box and remove (6) screws from outer edge then unclip and remove box. (Figure A)
3 Remove (4) screws from panel below steering column. Unclip and remove panel. (Figure B)
4 Unclip and remove center panel surrounding radio and A/C controls. (Figure C)
5 Remove (4) screws securing the radio. Unplug and remove the radio. (Figure D)

Continue to kit assembly.

A

Technical line drawing of a mechanical assembly with no visible text or symbols

B

Technical line drawing of a mechanical assembly with no visible text or symbols

C

Illustration of hands holding a car air conditioner unit with directional arrows indicating airflow or movement (no text or symbols)

D

Line drawing of a mechanical device with adjustment tools and circular components (no text or symbols)

Pontiac Solstice 2006-2007

1 Disconnect the negative battery terminal to prevent an accidental short circuit.
2 Manual transmission:

A. Lift up the lower edge of the instrument panel cluster trim plate enough to reach underneath and release the shift boot trim ring retaining tabs. (Figure A)

B. Lift up on the shift boot and loosen the setscrew to release the shift lever. (Figure B)

2 Automatic transmission:

A. Unclip and remove shifter trim ring. (Figure C)

3 Unclip and remove passenger assist handle trim panel. (Figure D)
4 Remove (2) bolts securing the passenger assist handle and remove handle. (Figure D)
5 Unclip and remove dash trim panel.
6 Remove (4) screws securing the radio. Unplug and remove the radio.

Continue to kit assembly.

Diagram of a car gear shift lever with directional arrows indicating motion (no text or symbols)

Diagram of a car gear shift lever mechanism with control panel and dial (no text or symbols)

C

Technical line drawing of a mechanical assembly with no visible text or symbols

Saturn Aura 2007

1 Disconnect the negative battery terminal to prevent an accidental short circuit.
2 Unclip and remove shifter trim ring. (Figure A)
3 Unclip and remove the center console trim panel, then remove (2) screws from bottom edge of dash trim panel. (Figure B)
4 Unclip and remove the key switch trim ring, then unclip and remove dash trim panel. (Figure C)
5 Remove (2) screws securing the climate controls.
6 Remove (4) screws securing the radio. Unplug and remove the radio.

Continue to kit assembly.

Diagram of a vehicle gear shift lever system with control panel and dashboard (no text or labels)

Interior view of a car dashboard with control panel and gear shift (no text or symbols)

C

Saturn Ion 2006-2007

1 Disconnect the negative battery terminal to prevent an accidental short circuit.
2 Unclip radio trim panel. (Figure A) Unplug connectors from trim panel and remove panel. (Figure B)
3 Remove (4) screws securing the radio. Unplug and remove the radio.

Continue to kit assembly.

Interior view of a car dashboard with steering wheel and air conditioner unit (no text or symbols)

B

Saturn Sky 2006-2007

1 Disconnect the negative battery terminal to prevent an accidental short circuit.
2 Unclip and remove side panel from driver's side of dash with door open and remove (2) 7 MM screws. (Figure A)
3 Remove (2) 7 MM screws from bottom edge of panel below steering wheel, unclip panel and remove panel.
4 Unclip and remove side panel from passenger side of dash with door open and remove (2) 7 MM screws from behind panel. (Figure B)
5 Open the glove box and disconnect the glove box dampener from the glove box assembly. Squeeze sides together to open further. (Figure C)
6 Remove (2) bolt covers from top edge of glove box frame. (Figure C)
7 Remove (5) bolts from glove box frame and remove frame. (Figure C)
8 Unsnap and remove climate control trim panel. (Figure D)
9 Remove (1) screw from lower left corner of radio trim panel and unplug connectors to remove panel. (Figure D)
10 Remove (4) screws securing the radio. Unplug and remove the radio. Continue to kit assembly.

A

B

C

Technical line drawing of a car air conditioning unit with fan and control panel (no text or symbols)

1 Disconnect the negative battery terminal to prevent an accidental short circuit.
2 Grasp the front edge of the shifter trim panel and pull outward and upward. (Figure A)
3 Squeeze the locking tabs located at the front edge of the shifter trim panel together to release the front edge of the panel from the center console. (Figure B)
4 Pull upward on the panel to release the remaining clips, and remove trim panel.
5 Remove (4) screws securing storage pocket and remove pocket. (Figure C)
6 Unclip and remove center dash trim panel. (Figure D)
7 Remove (4) screws securing the radio. Unplug and remove the radio.

Continue to kit assembly.

Top-down diagram of a car dashboard with control panel and directional arrows (no text or symbols)

Interior view of a car dashboard with steering wheel and control panel (no text or symbols)

B BOTTOM VIEW

Technical line drawing of a vehicle's steering wheel and cab assembly (no text or symbols)

DOUBLE DIN MOUNT RADIO PROVISION

*Note: Refer also to the instructions included with the aftermarket radio.

1 Slide the appropriate bracket into the trim plate aligning the holes in the trim plate to the clips on the bracket. (Figure A)
2 Slide the DDIN radio unit into the trim plate bracket assembly and secure the unit to the kit using the screws supplied with the head unit. (Figure B)
3 Aura, HHR, Sky and Vue only: Cut and remove top mounting tabs on each side of the Radio Housing. (Figure C)

Continue to final assembly.

Technical line drawing of a mechanical assembly with labeled component A (no text or symbols present)

Technical line drawing of a device with labeled components and directional arrows (no text or symbols)

C CUT THE TWO TOP HOLES OFF

STACKED ISO MOUNT RADIO PROVISION

*Note: Refer also to the instructions included with the aftermarket radio.

1 Slide the appropriate bracket into the trim plate aligning the holes in the trim plate to the clips on the bracket. (Figure A)
2 Slide the stacked ISO DIN units into the trim plate bracket assembly and secure the units to the kit using the screws supplied with the head units. (Figure B)
3 Aura, HHR, Sky and Vue only: Cut and remove top mounting tabs on each side of the Radio Housing. (Figure C)

Continue to final assembly.

Technical line drawing of a mechanical assembly with directional arrows indicating movement or force (no text or symbols present)

Technical line drawing of a server rack unit with ports and connectors (no text or symbols)

C CUT THE TWO TOP HOLES OFF

FINAL ASSEMBLY

A B C D

(A) Strip wire ends back 1/2"
B) Twist ends together
C) Solder
D) Tape

1 Locate the factory wiring harness in the dash. Metra recommends using the proper mating adapter and making connections as shown. (Isolate and individually tape off the ends of any unused wires to prevent electrical short circuit.)
2 Re-connect the negative battery terminal and test the unit for proper operation.
3 Reassemble radio and dash assemblies in reverse order of disassembly.

FINAL WIRING CONNECTIONS

Make wiring connections using the EIA color code chart shown below and the instructions included with the head unit. Metra recommends making connections as shown below; Strip, Splice, Solder, Tape. Isolate and individually tape off ends of any unused wires to prevent electrical short circuit.

METRA / EIA WIRING CODE

12V Ignition / Acc. . . . . . . . Red

Right Front (+) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

12V Batt / Memory. . . . . . . . . . . Yellow

Right Front (-). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Ground. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Power Antenna. . . . . . . . . . . . . . . Blue Amp Turn-On. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Amp Ground. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Illumination. . . . . . . . . . . . . Orange Dimmer. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

*NOTE: When a Black wire is not present, ground radio to vehicle chassis. All colors may not be present on all leads due to manufacturer's specifications.

NOTES

NOTES

NOTES

95-3302 INSTRUCTIONS