95-8208 - Kit voiture Metra - Free user manual and instructions

USER MANUAL 95-8208 Metra

Interior view of a car dashboard with air conditioner and digital display (no visible text or symbols)

KIT COMPONENTS

• A) Radio housing • B) Double DIN trim plate • C) Double DIN brackets

A

Technical line drawing of a mechanical component with no visible text or symbols

B

Line drawing of a rectangular frame with mounting holes and a central recess (no text or symbols)

C

Illustration of two panels with decorative patterns and a folded paper corner (no text or symbols)

WIRING & ANTENNA CONNECTIONS (sold separately)

WiringHarness:

• 70-1761 - Toyota harness 1987-up
• TYTO-01 - Toyota amp interface harness 2003-up
Antenna Adapter:
- Not required

TOOLS REQUIRED

- Phillips screwdriver • Panel removal tool • Socket wrench

Three line drawings of different types of tools: a screwdriver, a pointed tool, and a wrench (no text or symbols present)

CAUTION: Metra recommends disconnecting the negative battery terminal before beginning any installation. All accessories, switches, and especially air bag indicator lights must be plugged in before reconnecting the battery or cycling the ignition.

Note: Refer to the instructions included with the aftermarket radio.

KNOWLEDGE IS POWER

Enhance your installation and fabrication skills by enrolling in the most recognized and respected mobile electronics school in our industry. Log onto www.installerinstitute.com or call 800-354-6782 for more information and take steps toward a better tomorrow.

Metra recommends MECP certified technicians

Toyota Sienna 2004-2010

1. Unclip and remove panels from left and right side of radio. (Figure A)
2. Unclip and remove panel or speaker cover above radio. (Figure B)
3. Remove (4) 10 mm bolts from radio to remove. (Figure C)
   Continued to kit assembly

Interior view of a car dashboard with air vent, steering wheel, and control panel (no text or symbols)

(Figure A)

Top-down view of a car dashboard with air vent, steering wheel, and control panel (no text or symbols visible)

(Figure B)

Top-down view of a car dashboard with air vent, buttons, and control panel (no text or symbols)

(Figure C)

Double DIN radio provision

1. Snap the Double DIN brackets to the inside edge of the radio housing. (Figure A)
2. Slide the Double DIN radio into the bracket/housing assembly and secure the radio to the assembly using the screws supplied with the radio. (Figure B)
3. Snap the Double DIN trim plate into the radio housing. (Figure C)
4. Locate the factory wiring harness in the dash. Metra recommends using the proper mating adapter from Metra or AXXESS. Re-connect the negative battery terminal and test the unit for proper operation.
5. Reassemble dash in reverse order of disassembly.

Technical line drawing of a mechanical device with internal components and directional arrows (no text or symbols)

(Figure A)

Technical line drawing of a device with arrows indicating directional movement or assembly (no text or symbols present)

(Figure B)

Technical line drawing of a mechanical device housing with internal components (no text or symbols)

(Figure C)

Stacked ISO mount units provision

1. Snap the Double DIN brackets to the inside edge of the radio housing. (Figure A)
2. Slide the Stacked ISO units into the bracket/housing assembly and secure the units to the assembly using the screws supplied with the units. (Figure B)
3. Snap the Double DIN trim plate into the radio housing. (Figure C)
4. Locate the factory wiring harness in the dash. Metra recommends using the proper mating adapter from Metra or AXXESS. Re-connect the negative battery terminal and test the unit for proper operation.
5. Reassemble dash in reverse order of disassembly.

Technical line drawing of a mechanical housing or enclosure with internal components and directional arrows indicating movement (no text or symbols)

(Figure A)

Technical line drawing of a device casing with control panel and buttons (no text or symbols)

(Figure B)

Technical line drawing of a mechanical device with internal components and mounting brackets (no text or symbols)

(Figure C)

Notes

Notes

APLICACIONES

Toyota Sienna 2004-2010 95-8208

CARACTERÍSTICAS DEL KIT

Interior view of a car dashboard with air conditioner and control panel (no visible text or symbols)

COMPONENTES DEL KIT

Technical line drawing of a mechanical component with no visible text or symbols

B

Line drawing of a rectangular frame with mounting holes and a central recess (no text or symbols)

C

Illustration of two panels with decorative patterns and a folded paper corner (no text or symbols)

Three line drawings of different types of tools: a screwdriver, a pointed tool, and a wrench (no text or symbols present)

Interior view of a car dashboard with control panel and directional arrows indicating traffic flow (no text or symbols)

(Figura A)

Top-down view of a car dashboard with air vent, steering wheel, and control panel (no text or symbols visible)

(Figura B)

Top-down view of a car dashboard with air vent, buttons, and control panel (no text or symbols)

(Figura C)

Technical line drawing of a mechanical device with internal components and directional arrows (no text or symbols)

(Figura A)

Technical line drawing of a device with arrows indicating directional movement or assembly (no text or symbols present)

(Figura B)

Technical line drawing of a mechanical device housing with internal components (no text or symbols)

(Figura C)

Technical line drawing of a mechanical housing or enclosure with internal components and directional arrows indicating movement (no text or symbols)

(Figura A)

Technical line drawing of a device casing with control panel and buttons (no text or symbols)

(Figura B)

Technical line drawing of a mechanical device with internal components and housing (no text or symbols)

(Figura C)

Notas

Notas