95-8728B - Kit voiture Metra - Free user manual and instructions

USER MANUAL 95-8728B Metra

Interior view of a car dashboard with a digital display and control knobs (no visible text or symbols)

Mercedes R Class 2006-2011

Visit MetraOnline.com for more detailed information about the product and up-to-date vehicle specific applications

KIT FEATURES

• ISO DDIN radio provision
- Painted black

KIT COMPONENTS

• A) Radio trim panel • B) Radio brackets • C) Radio screws (8) • D) Radio trim panel screws (4)

A

Isometric line drawing of a rectangular device casing with internal compartments (no text or symbols)

B

C

D

TABLE OF CONTENTS

Dash Disassembly 2

Kit Preparation 3

Kit Assembly 3

WIRING & ANTENNA CONNECTIONS (sold separately)

Wiring Harness: XSVI-9005-NAV (non-amped only)

Antenna Adapter: 40-EU10

Steering Wheel Control Interface: • ASWC-1

TOOLS REQUIRED

• Panel removal tool • Phillips screwdriver
  • 3mm Allen screwdriver

Attention! Let the vehicle sit with the key out of the ignition for a few minutes before removing the factory radio. When testing the aftermarket equipment, ensure that all factory equipment is connected before cycling the key to ignition.

DASH DISASSEMBLY

1. Unclip the climate control panel, then set to the side. No need to disconnect the wiring harness. The tabs holding the panel in place are located on the left and right sides of the panel, towards the top. (Figure A)

2. Remove (2) Torx screws below the radio (white circles in figure), then pull down the metal clips to release the radio. Slide the radio out, then unplug and remove the radio. (Figure B)

Continue to Kit Preparation

Top of Climate

(Figure A)

Interior view of a car dashboard with digital gauges and control buttons (no visible text or symbols)

(Figure B)

KIT PREPARATION KIT ASSEMB

1. Remove the top trim from the factory radio by pulling back on the release tab in the middle, then sliding the trim to the right. Follow the same procedure to attach it to the radio trim panel. (Figure A)

2. Secure the radio brackets to the radio trim panel using the (4) radio trim panel screws supplied. (Figure B)

Continue to Kit Assembly

Interior view of a device showing a speaker grille and drive casing (no visible text or symbols)

(Figure A) (Figure A)

Technical line drawing of a mechanical component with no visible text or symbols

(Figure B)

1. Slide the radio into the bracket/panel assembly, then secure the radio using either the screws supplied with the radio, or the radio screws provided. (Figure A)

2. Locate the factory wiring harness and antenna connector in the dash and complete all necessary connections to the radio. Metra recommends using the proper mating adapter from Metra and/or Axxess. Test the radio for proper operation.

3. Slide the radio into the dash, then push the metal clips up into the bottom of the kit. Using the factory Torx screws, secure the metal clips to the dash to secure the radio assembly.

4. Clip the climate control panel back in to complete the installation.

Technical diagram of a device with labeled components and directional arrows indicating flow or movement.

If you are having difficulties with the installation of this product, contact our Tech Support line either by phone at 1-800-253-TECH, or email at [e-mail]. Before doing so, look over the instruction booklet a second time and ensure that the installation was performed exactly as the instruction booklet is stated. Have the vehicle apart and ready to perform troubleshooting steps before contacting Metra/Axxess Tech Support.

KNOWLEDGE IS POWER

Enhance your installation and fabrication skills by enrolling in the most recognized and respected mobile electronics school in our industry. Log onto www.installerinstitute.com or call 800-354-6782 for more information and take steps toward a better tomorrow.

Metra recommends MECP certified technicians

Visit MetraOnline.com for more detailed information about the product and up-to-date vehicle specific applications.

ISO DDIN radio provision

Painted black

Exterior view of a black rectangular device with two small metal bracket components (no text or symbols visible)

HARDWARE INCLUDED

KIT COMPONENTS

• Radio trim panel
• Radio brackets
  • Radio screws (8)
• Radio trim panel screws (4)

WIRING & ANTENNA CONNECTIONS

(sold separately)

• Wiring Harness: XSVI-9005-NAV (non-amped only)
- Antenna Adapter: 40-EU10
• Steering wheel control interface: ASWC-1

SALES 800-221-0932